summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* video: mb862xx: change controller detection messageAnatolij Gustschin2011-08-04-1/+1
| | | | Signed-off-by: Anatolij Gustschin <agust@denx.de>
* video: mb862xx: support Coral-PA controllerAnatolij Gustschin2011-08-04-5/+27
| | | | | | | | | Add detection of Coral-PA and configure Coral CCF an MMR parameters using CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx_MMR macros. Use CCF and MMR parameters for Coral-P Eval. Board if the appropriate macros weren't defined. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* video: Add SHARP LQ084S3LG01 LCD support on P1022DSTimur Tabi2011-08-04-19/+40
| | | | | | | | | | | | | | | | | The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board. This device only supports 800x600 resolution, so if that resolution is selected, assume that this is the device. The device is attached to the LVDS port on the P1022DS board. The existing 800x600 entry (for the PDM360NG board) is actually 800x480, so we fix that. To support two different 800x resolutions, the Y-resolution is now passed to fsl_diu_init() and both values are used to pick the proper fb_videomode structure. The data for the 800x600 video mode is originally from Jiang Yutang. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Jiang Yutang <b14898@freescale.com>
* video: Use memset instead of loopMatthias Weisser2011-08-02-2/+1
| | | | | | | There is a optimized version of memset in u-boot available so use it instead of the hand written loop version. Signed-off-by: Matthias Weisser <weisserm@arcor.de>
* Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-08-02-12/+1
|\ | | | | | | | | * 'master' of git://git.denx.de/u-boot-mmc: Revert "AT91:mmc:fix multiple read/write error"
| * Revert "AT91:mmc:fix multiple read/write error"Andy Fleming2011-07-28-12/+1
| | | | | | | | | | | | | | | | | | This reverts commit c310fc840472a36e4b9d2505830e9dc8d458d63c. The Atmel custodian had apparently rejected this patch's approach in another thread, so this patch reverts it for now. Signed-off-by: Andy Fleming <afleming@freescale.com>
* | sf: macronix: disable write protection when initializingSimon Guinot2011-08-02-0/+42
| | | | | | | | Signed-off-by: Simon Guinot <sguinot@lacie.com>
* | sf: spansion: add support for S25FL129P_64KShaohui Xie2011-08-02-0/+9
| | | | | | | | | | Signed-off-by: Shaohui Xie <b21989@freescale.com> Cc: Mike Frysinger <vapier@gentoo.org>
* | mtd/spi/macronix.c: add MX25L4005 and MX25L8005Macpaul Lin2011-08-02-0/+16
| | | | | | | | | | | | | | | | | | Add support of MX25L4005 and MX25L8005 according to the datasheet http://www.mct.net/download/macronix/mx25l8005.pdf This patch has been tested with MX25L4005 and MX25L8005 Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2011-08-02-7/+7
|\ \ | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-ppc4xx: net/4xx: Install interrupt handler after driver registration
| * | net/4xx: Install interrupt handler after driver registrationStefan Roese2011-07-28-7/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Only install der 4xx-EMAC interrupt handlers *after* the core network driver is registered. This problem was noticed on the APM Taishan 440GX board, where the board hung upon bootup after displaying "Net:". Signed-off-by: Stefan Roese <sr@denx.de>
* | | Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk2011-08-02-462/+904
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-blackfin: Blackfin: jtag-console: fix timer usage Blackfin: switch to common display_options() Blackfin: serial: move early debug strings into .rodata section Blackfin: adi boards: also set stderr to nc with helper Blackfin: update anomaly lists to latest public info Blackfin: serial: convert to bfin_{read,write} helpers Blackfin: split out async setup Blackfin: adi boards: enable pretty flash progress output Blackfin: drop unused dma.h header from start code Blackfin: portmux: allow header to be included in assembly files Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings Blackfin: sync MMR read/write helpers with Linux Blackfin: gpio: optimize free path a little Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR Blackfin: uart: fix printf warning Blackfin: add init.elf helper code Blackfin: dont reset SWRST on newer bf526 parts Blackfin: adi boards: enable multi serial support by default Blackfin: uart: add multiple serial support Blackfin: uart: move debug buffers into local bss
| * | | Blackfin: jtag-console: fix timer usageMike Frysinger2011-07-12-2/+2
| | | | | | | | | | | | | | | | | | | | Reported-by: Graeme Russ <graeme.russ@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: switch to common display_options()Mike Frysinger2011-07-12-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use common code to output the version string rather than doing it ourselves. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: serial: move early debug strings into .rodata sectionMike Frysinger2011-07-12-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rewrite the assembly serial_early_puts() helper to place the strings in the .rodata section rather than embedding them directly in the .text section. Using .text is a little simpler, but it doesn't let people execute out of internal L1 sram (since core reads don't work on those regions). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: adi boards: also set stderr to nc with helperMike Frysinger2011-07-12-1/+2
| | | | | | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: update anomaly lists to latest public infoMike Frysinger2011-07-12-221/+335
| | | | | | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: serial: convert to bfin_{read,write} helpersMike Frysinger2011-07-12-17/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the serial struct declares the sizes for us, no need to hardcode them in the accessor functions. Let the bfin_{read,write} helpers do it for us. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: split out async setupMike Frysinger2011-07-12-50/+84
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We really only need to tweak the async banks in the initcode if the processor is booting out of it, otherwise we can wait until later on in the CPU booting setup. This also makes testing in the sim and early bring up over JTAG work much smoother when the initcode gets bypassed. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: adi boards: enable pretty flash progress outputMike Frysinger2011-07-12-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For only ~150 bytes increase in size, we can get a nice flash progress indicator rather than just the boring dots (which don't tell too much about overall progress). So enable it for all ADI boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: drop unused dma.h header from start codeMike Frysinger2011-07-12-1/+0
| | | | | | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: portmux: allow header to be included in assembly filesMike Frysinger2011-07-12-0/+4
| | | | | | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi supportHarald Krapfenbauer2011-07-12-3/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These boards have an mmc/sd slot on them connected over SPI, so enable the driver. Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settingsHarald Krapfenbauer2011-07-12-47/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These boards can have an addon card plugged onto them, so enable support for it. Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: sync MMR read/write helpers with LinuxMike Frysinger2011-07-12-46/+42
| | | | | | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: gpio: optimize free path a littleMike Frysinger2011-07-12-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we aren't doing resource tracking, the gpio_free() function is a stub that simply returns, so pull this logic up a level and make it an inline stub in the header. Now we don't have to waste time at any of the call sites. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDRMike Frysinger2011-07-12-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the default post word location to an L1 data location for all Blackfin parts so things "just work" for most people. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: uart: fix printf warningMike Frysinger2011-07-12-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The code uses %i to printf a size_t when it should use %zu, otherwise we get a warning from gcc about it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: add init.elf helper codeMike Frysinger2011-07-12-2/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This creates a standalone ELF that executes just the Blackfin initcode. This is useful for people who want to program the low level aspects of the CPU (memory/clocks/etc...) and can easily be used with JTAG for quick booting while developing. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: dont reset SWRST on newer bf526 partsMike Frysinger2011-07-12-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The bug in the BF526 rom when doing a software reset exists only in older silicon versions, so don't clear SWRST on newer parts. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: adi boards: enable multi serial support by defaultMike Frysinger2011-07-12-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | Since this only adds less than 3KiB, enable for all ADI boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: uart: add multiple serial supportMike Frysinger2011-07-12-55/+222
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This brings CONFIG_SERIAL_MULTI support to the Blackfin on-chip UARTs. Ends up adding only ~512bytes per additional UART. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | | Blackfin: uart: move debug buffers into local bssMike Frysinger2011-07-12-8/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | There's no need for these saved buffers to be global symbols, or in the data section. So mark them static to move them into the bss. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-mipsWolfgang Denk2011-08-02-10/+56
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mips: README: update MIPS related informations MIPS: make cache operation mode configurable MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFG MIPS: INCA-IP: rename inca-swap-bytes host tool
| * | | | README: update MIPS related informationsDaniel Schwierzeck2011-07-31-1/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amend section 'Directory Hierarchy' for current MIPS directory. Describe config options for MIPS. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | | | MIPS: make cache operation mode configurableDaniel Schwierzeck2011-07-31-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the cache operation mode is hard-coded to CONF_CM_CACHABLE_NONCOHERENT. This is not appropiate for CPUs or SOCs which operate at a different mode. This patch makes the cache operation mode configurable via board config. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | | | MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFGDaniel Schwierzeck2011-07-31-4/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This define is a board-specific config option and should be renamed to follow the U-Boot naming convention. Additionally, add an explaining comment for this option. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | | | MIPS: INCA-IP: rename inca-swap-bytes host toolDaniel Schwierzeck2011-07-31-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The INCA-IP SoC belongs to the Lantiq XWAY SoC product portfolio. For the upcoming support of other Lantiq SoC devices this tool should not solely depend on the INCA-IP board. Rename the tool to xway-swap-bytes and add an config option to enable compilation optionally. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
* | | | | tqm834x.c: fix compiler warningWolfgang Denk2011-08-02-3/+3
| |_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix: tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards qualifiers from pointer target type Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | | | environment.h: fix warning: "CONFIG_ENV_IS_EMBEDDED" redefinedWolfgang Denk2011-08-01-1/+3
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de>
* | | | fpga: constify to fix build warningWolfgang Denk2011-08-01-92/+92
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix compiler warning: cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data' from incompatible pointer type Adding the needed 'const' here entails a whole bunch of additonal changes all over the FPGA code. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de> Cc: Murray Jensen <Murray.Jensen@csiro.au> Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
* | | | Unify timer_init() and cpu_init() prototypesWolfgang Denk2011-08-01-35/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clean up some duplicated prototype declarations. Get rid of now useless AVR32 initcalls.h file. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: Graeme Russ <graeme.russ@gmail.com>
* | | | ARM: fix error: conflicting types for 'setenv'seedshope2011-08-01-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also remove bogus comment. Signed-off-by: Zhong hongbo <bocui107@gmail.com> Changed commit message Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.aribaud@free.fr>
* | | | cfb_console.c: checkpatch cleanupWolfgang Denk2011-08-01-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following: ERROR: do not initialise statics to 0 or NULL ERROR: do not use assignment in if condition Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | | cfb_console.c: drop custom PRINTD() and use debug() insteadWolfgang Denk2011-08-01-9/+2
| | | | | | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | | Cosmetic: reformat drivers/video/cfb_console.cWolfgang Denk2011-08-01-484/+609
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Run cfb_console.c through indent and manually fix some of he deficiencies of the automatic line breaking. Fix multiline comments, excessive line spacing and such. No changes to code done. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2011-07-30-55/+246
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of /home/wd/git/u-boot/custodians: powerpc/8xxx: Remove dependency on <usb.h> powerpc/85xx: enable USB2 gadget mode for corenet ds board powerpc/85xx: verify the device tree before booting Linux MPC8xxx: drop redundant boot messages powerpc/85xx: Fix build failure for P1023RDS powerpc/p2041rdb: Enable SATA support powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500 powerpc/85xx: Fix up clock_freq property in CAN node of dts 85xx: enable FDT support for STX SSA board powerpc/85xx: provide 85xx flush_icache for cmd_cache powerpc/p2041rdb: Enable backside L2 cache support powerpc/85xx: Handle the lack of L2 cache on P2040/P2040E powerpc/85xx: Add support for P2041[e] XAUI in SERDES powerpc/85xx: Rename P2040 id & SERDES to P2041 powerpc/85xx: Adding configuration for DCSRCR to enable 32M access powerpc/85xx: Fix setting of EPAPR_MAGIC value
| * | | powerpc/8xxx: Remove dependency on <usb.h>Kumar Gala2011-07-29-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We used <usb.h> for USB_MAX_DEVICE. However this requires we actual build in support for USB into u-boot (which should not be required for device tree fixup). At this time no FSL SoC that utilizies this code (83xx/85xx) has more than 2 USB controllers. So we replace USB_MAX_DEVICE with a local define FSL_MAX_NUM_USB_CTRLS. If/when a device shows up with more than 2 controllers we can easily bump this value or refactor into a proper define per SoC. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | powerpc/85xx: enable USB2 gadget mode for corenet ds boardShaohui Xie2011-07-29-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to 'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break out if it cannot find 'usb1', so drop the 'else' clause to make driver scan all the 'usbx'. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | powerpc/85xx: verify the device tree before booting LinuxTimur Tabi2011-07-29-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce ft_verify_fdt(), a function that is called after the device tree has been fixed up, that displays warning messages if there is a mismatch between the physical addresses of some devices that U-Boot has configured with what the device tree says the addresses are. This is a particular problem when booting a 36-bit device tree from a 32-bit U-Boot (or vice versa), because the physical address of CCSR is wrong in the device tree. When the operating system boots, no messages are displayed, so the user generally has no idea what's wrong. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-06 14:07:39 +0000