summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
* MLK-10908: imx: mx6sx Add mx6sx_17x17_arm2_qspi2 configHan Xu2015-05-15-0/+7
| | | | | | This config was missed when porting to 2015.04 u-boot. Signed-off-by: Han Xu <b45815@freescale.com>
* MLK-10885 imx: mx6slevk ignore elan init when no epdc on boardPeng Fan2015-05-14-13/+21
| | | | | | | | | | | | | | | | If no epdc pannel is plugged into mx6slevk board, no need to do the elan init operation for each i2c init transfer which will slow the i2c speed. If epdc panned is plugged into mx6slevk board, all works as the original patch: "b6ba68516b681a38025252bd0ef6a6ed3e8adfa0" - "MLK-10215 Add elan init in i.MX6SL-EVK board" This patch also fix a bug that setup_elan_pads should be called in board_init, but not board_late_init where too late to setup_elan_pads. And align pad property with linux kernel, value is 0x17000. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10839: arm: imx: mx7d 19x19 lpddr3 arm2 board supportAdrian Alonso2015-05-13-2/+1072
| | | | | | | | | | | | | * Add mx7d_19x19_lpddr3_arm2 target board supprt * Enable i2c, spinor, usb, usdhc, qspi, enet, uart * Build targets mx7d_19x19_lpddr3_arm2_defconfig mx7d_19x19_lpddr3_arm2_eimnor_defconfig - Set EIMNOR settings for Intel Sibley Asynchronous mode - Set flash sector size for 256kb (erase block size) Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10884 imx: MX6SX: Fix IOMUXC GPR registers access issueYe.Li2015-05-13-6/+2
| | | | | | | | The iomuxc structure has changed to add 0x4000 offset for i.MX6SX and UL, so when using this structure to access gpr registers needs to change the base address to IOMUXC_BASE_ADDR. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10873-2 imx:mx6ul removed uncompiled pmic codePeng Fan2015-05-11-8/+0
| | | | | | | This piece of code will never be compiled and used, since we use pmic framework. So remove the code block. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10873-1 imx:mx7d use pmic frameworkPeng Fan2015-05-11-93/+58
| | | | | | Use pmic framework to simplify code and make code clean. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10870 imx: mx7d: Implement to get board serial numberYe.Li2015-05-11-1/+7
| | | | | | Get the Unique ID of the chip from the fuse TESTER0 and TESTER1. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10865 imx: mx6ulevk: Add android supportYe.Li2015-05-08-0/+182
| | | | | | | | Add android features booti, fastboot and recovery to i.MX6UL EVK board. Since there is no user button on the board, we can't implement the recovery by using button. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10855 imx: mx6ulevk/ddr3_arm2: Fix bmode value for SD1 and SD2Ye.Li2015-05-07-3/+3
| | | | | | Correct USDHC Port Selection bits in bmode value for SD1 and SD2. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10852 imx: mx6ul_ddr3_arm2: Add support for NAND bootYe.Li2015-05-07-20/+27
| | | | | | | | | | | Since the NAND has two pins conflict with SD2, when NAND is enabled, we must disable SD2. So the CONFIG_SYS_FSL_USDHC_NUM needs configure to 1 and should be moved to under defining CONFIG_SYS_USE_NAND. New build target for NAND boot: mx6ul_ddr3_arm2_nand_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10841 imx: mx6ul_ddr3_arm2: Add support for WEIMNOR bootYe.Li2015-05-07-5/+17
| | | | | | | | | | Correct the EIMNOR settings to non-mux mode and set the environment variables configuration to FLASH when using WEIMNOR boot. New target is added for build WEIMNOR boot u-boot: mx6ul_ddr3_arm2_eimnor_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10740: add maximum ecc platfrom can supportHan Xu2015-05-07-1/+7
| | | | | | | | Add maximum ecc strength for each platfrom to avoid the calculated ecc exceed the limitation. Signed-off-by: Han Xu <b45815@freescale.com> (cherry picked from commit fdc5bac6ae8b699924c4e84b86e38aa73f694827)
* MLK-10747-2 video: ipu: Enable/disable LDB_DI clock when necessaryLiu Ying2015-05-07-7/+65
| | | | | | | | This patch adds enable/disable hooks support for ldb_di[0/1] clocks and enables/disables them when necessary. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> (cherry picked from commit 839a1da941be48baf27c9cb28939cc6b2030424a)
* MLK-10747-1 video: ipu: Build ldb_di clock relevant code only for MX6 and MX53Liu Ying2015-05-07-2/+14
| | | | | | | | The LDB is found in MX6 variants and MX53, so this patch makes the ldb_di clock relevant code be built only for them. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> (cherry picked from commit c0dc175a9780505ec8939bda5dda9c2ec549a7f0)
* MLK-10829-2 imx:mx6 support thermal for all mx6Peng Fan2015-05-06-14/+10
| | | | | | | | Move CONFIG_IMX_THERMAL to mx6_common.h Make CONFIG_MXC_OCOTP only depends on CONFIG_CMD_FUSE, since when THERMAL is not implemented, we may use fuse. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10829-1 imx:mx6sx correct i2c and video clock settingsPeng Fan2015-05-06-13/+3
| | | | | | | | Change MXC_CCM_CCGR6_I2C4_xx to MXC_CCM_CCGR6_I2C4_SERIAL_xx Remove duplicated mxs_set_vadcclk Correct enable_pll_video usage Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10827 imx: mx6 update thermal driver according new equationPeng Fan2015-05-06-17/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From IC guys: " After a thorough accuracy study of the Temp sense circuit, we found that with our current equation, an average part can read 7 degrees lower than a known forced temperature. We also found out that the standard variance was around 2C; which is the tightest distribution that we could create. We need to change the temp sense equation to center the average part around the target temperature. Old Equation: Temp = Troom,cal – slope*(Count measured – Count room fuse) Where Troom,cal = 25C and Slope = 0.4297157 – (0.0015974 * Count room fuse) New Equation: Temp = Troom,cal – slope*(Count measured – Count room fuse) +offset Where Troom,cal = 25C and Slope = 0.4445388 – (0.0016549 * Count room fuse) Offset = 3.580661 " According the new equation, update the thermal driver. c1 and c2 changed to u64 type and update comments. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10817 imx:mx6ul_ddr3_arm2 add mx6ul ddr3 arm2 board supportPeng Fan2015-05-05-0/+1762
| | | | | | | | | | | | | Add board code for mx6ul ddr3 arm2 board. QSPI, USDHC, ENET, USB, VIDEO, SPINOR, EIMNOR Add sd1, qspi and spinor boot support DDR script is 1.02 version. Signed-off-by: Fugang Duan <b38611@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10821 imx: mx6ulevk: Add board support for mx6ulevkYe.Li2015-05-05-0/+1570
| | | | | | | | | | | Add BSP codes to support modules on the board: I2C, SD/eMMC, NAND, QSPI, FEC1/FEC2, USB, LCDIF, 74LV, Serial DDR version: 1.0 Build target: mx6ulevk_config mx6ulevk_qspi1_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10812-6 net: fec: add platform check to avoid to access the reserved ↵Peng Fan2015-05-05-1/+4
| | | | | | | | | register Add platform check to avoid to access the reserved register Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10812-5 imx: qspi i.MX6UL needs at least 16 bytes when writePeng Fan2015-05-05-2/+2
| | | | | | i.MX6UL qspi controller also needs at least 16 bytes when writing. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10812-4 mxc:gpio Add MX6UL supportPeng Fan2015-05-05-0/+4
| | | | | | comment out GPIO6/7 for MX6UL Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10812-3 imx:mx6ul PAD_CTL_SPEED_LOW for mx6ulPeng Fan2015-05-05-1/+1
| | | | | | PAD_CTL_SPEED_LOW for mx6ul same with mx6sx. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10812-2 imx:mx6ul add clock supportPeng Fan2015-05-05-61/+421
| | | | | | | | | | | | add i.MX6UL clock related settings/macros/apis When using TFT43AB, its pixel size is 480x272 which needs a slow pix clock. Without apply the test_div in PLL video, we can't get the pix clock in the rate. So change the LCDIF clock calculation to use the test_div. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10812-1 imx:mx6 add i2c4 supportPeng Fan2015-05-05-8/+28
| | | | | | I2C4 support for i.MX Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10808-5 imx: mx6ul: Update soc relevant settingsYe.Li2015-05-05-9/+25
| | | | | | | Remove PCIe, xPU power, PL310 L2 Cache for MX6UL. Update FEC MAC address, WDOG settings, USDHC clock rate. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10808-4 imx: Move system counter driver to imx-commonYe.Li2015-05-04-11/+28
| | | | | | | | | | | | | Since the system counter driver will also be used by mx6ul, move this timer driver to imx-common and rename it as syscounter.c For mx6ul and mx7, configurations are used for choose the GPT timer or system counter timer (default). GPT timer: CONFIG_GPT_TIMER System counter timer: CONFIG_SYSCOUNTER_TIMER Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10808-3 imx: mx6ul: Update imx registers head fileYe.Li2015-05-04-33/+114
| | | | | | Update imx registers base address for i.MX6UL Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10808-2 imx: mx6ul: Add pins IOMUX head fileYe.Li2015-05-04-0/+1068
| | | | | | | Add i.MX6UL pins IOMUX file which defines the IOMUX settings for choose. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10808-1 imx: mx6ul: Add i.MX6UL CPU typeYe.Li2015-05-04-2/+5
| | | | | | | | | Add MXC_CPU_MX6UL for i.MX6UL CPU type which is got at runtime. The 0x64 is defined as i.MX6Ul CPU type value in RM, but the value has been occupied by i.MX6D as a dummy CPU type. So we also need change i.MX6D to a invalid value 0x67. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10774-53 imx: update setting pmic volatagePeng Fan2015-04-29-8/+179
| | | | | | | | We should not rely on pfuze_common_init to set the voltage, may be we should remove the voltage settings in pfuze_common_init. This patch is to setting the voltages in power_init_board. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-52 nand: mxs correct MXS_DMA_ALIGNMENTPeng Fan2015-04-29-1/+1
| | | | | | | | | | | | We should align MXS_DMA_ALIGNMENT with ARCH_DMA_MINALIGN, otherwise we may encounter errors, " NAND: ERROR: v7_dcache_inval_range - start address is not aligned - 0xbdf1d1a0 ERROR: v7_dcache_inval_range - stop address is not aligned - 0xbdf1f4a0 ERROR: v7_dcache_inval_range - start address is not aligned - 0xbdf1d1a0 " Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10733 imx: imx6qpsabreauto: Update IPU QoS settingsLiu Ying2015-04-29-3/+3
| | | | | | | | | | | | | | Update IPU QoS settings from 0x007f007f to 0x77177717 according to the SoC team's recommendation. This change should be able to balance AXI ID0/2/3 priority and set AXI ID1 priority relatively lower, which matches the way we use AXI ID0/1/2/3 for IDMAC23(0), regular IDMACs, IDMAC27 and IDMAC28 respectively in kernel. The specific priority values for each AXI ID are supposed to be picked for the sake of an overall good system performance. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> (cherry picked from commit 7c4bee613dc47c9e2fb147a159236bca04b8618b)
* MA-6580 recovery.img cannot be authenticated by HABguoyin.chen2015-04-29-9/+13
| | | | | | | | | | Remove the authentication size to be a fixed size, due to recovery.img may be much bigger than the boot.img Add signature size to boot or recovery image size, which is added by boot_signer in android build process Signed-off-by: guoyin.chen <guoyin.chen@freescale.com> (cherry picked from commit d59b24fefcd56d085c4010643ca9f6522a3cc58a)
* MLK-10708 imx:mx6qp Update Saturation THR for PRExPeng Fan2015-04-29-4/+4
| | | | | | | | Update settings for PRE. Value for Saturation THR of PREx, changed from 0x20 to 0x10 to make system more stable. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 02e7090604e55d9690532294b02b499609d46e63)
* MLK-10702 imx: mx7d: clock: correct fec MDC root clockFugang Duan2015-04-29-1/+1
| | | | | | | | In i.MX7d platform, fec MDC root clock is ENET_AXI_ROOT_CLK, not ipg clock, correct it. Signed-off-by: Fugang Duan <B38611@freescale.com> (cherry picked from commit 07105e18dd0899c47ef80d3fddecf3ef250d895a)
* MLK-10701 net: fec_mxc: setup right value for mdio hold timeFugang Duan2015-04-29-1/+3
| | | | | | | | | | | | | | The minimal hold time according to IEE802.3 (clause 22) is 10 ns. HOLDTIME + 1 is the number of clk cycles the fec is holding the output. Set the right hold time value when the MDC root clock is greater than 100Mhz. The issue was reported on i.MX28 and is fixed by Uwe Kleine-König in kernel: https://git.kernel.org/cgit/linux/kernel/git/next/linux-next.git/commit/ drivers/net/ethernet/freescale/fec_main.c?id=63c607321492c5efc7a31bc4ea734b877f8e7f87 Signed-off-by: Fugang Duan <B38611@freescale.com> (cherry picked from commit 0373a160e7f698064a6625e85f9120b6c81c1b61)
* MLK-10774-51 imx: Add epdc default configuration filePeng Fan2015-04-29-0/+28
| | | | | | Add epdc default configuration file. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-50 imx:mx7dsabresd move VIDEO config before EPDCPeng Fan2015-04-29-16/+16
| | | | | | Move VIDEO config to the front of EPDC Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-34 imx6:dlsabresd/slevk Fix build break when enables EPDCYe.Li2015-04-29-11/+14
| | | | | | | | | | | | | -Use the new pins' name for imx6dl. -Change the read/write to registers by using register structure. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 66e7a93ff1e47d0e47627a984bcf2337db4f3bbf) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: board/freescale/mx6sabresd/mx6sabresd.c Remove imx6dl part, since already fixed.
* MLK-10774-49 imx: pcie update to align with imx_v2014.04Peng Fan2015-04-29-4/+87
| | | | | | | Update pcie code to align with imx_v2014.04. Mainly add DEBUG related stuff. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-48 imx: mx7 update hab_caam_clock_enablePeng Fan2015-04-29-11/+8
| | | | | | | Merge hab_caam_clock_enable and hab_caam_clock_disable into one function Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00329484-2 ARM:MX6: Clear Align bit in SCTLRPeng Fan2015-04-29-0/+3
| | | | | | | | | | | This problem is found when debugging QuadSPI. When "A" bit is enabled, unaligned access will cause data abort exception. Actually, we do not want this exception. So clear the align bit for MX6 SOCs. Tested this code with android team colleague and did not find problem. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit aa76a7e472e34bc59554f9932d611b1047d24590)
* MLK-10774-47 imx: mx7dsabresd enable thermalPeng Fan2015-04-29-0/+2
| | | | | | Enable thermal for mx7dsabresd board. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10674-2 imx: mx6qp settings for PREPeng Fan2015-04-29-0/+38
| | | | | | | | | | | | | | | | | | | | | | Since the following piece settings can not be in DCD table, we add them in enable_ipu_clock. " setmem /32 0x00bb048c = 0x00000002 ## Bypass IPU1 QoS generator setmem /32 0x00bb050c = 0x00000002 ## Bypass IPU2 QoS generator setmem /32 0x00bb0690 = 0x00000200 ## Bandwidth THR for of PRE0 setmem /32 0x00bb0710 = 0x00000200 ## Bandwidth THR for of PRE1 setmem /32 0x00bb0790 = 0x00000200 ## Bandwidth THR for of PRE2 setmem /32 0x00bb0810 = 0x00000200 ## Bandwidth THR for of PRE3 setmem /32 0x00bb0694 = 0x00000020 ## Saturation THR for of PRE0 setmem /32 0x00bb0714 = 0x00000020 ## Saturation THR for of PRE1 setmem /32 0x00bb0794 = 0x00000020 ## Saturation THR for of PRE2 setmem /32 0x00bb0814 = 0x00000020 ## Saturation THR for of PRE " CONFIG_VIDEO_IPUV3 is always defined in mx6sabre_common.h, the settings sure will effect. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 61cec88a59ebf450dd1352d81e03b5aa842e1d71)
* MLK-10674-1 imx: mx6qpsabreauto Update to 1.05 DDR ScriptPeng Fan2015-04-29-1/+9
| | | | | | | | | | | | | | | | | | | | Update to 1.05 ddr script, url: http://compass.freescale.net/livelink/livelink?func=ll& objId=233944823&objAction=browse&viewType=1 File name: arik_r2_sabre_ddr3_528_1.05c.inc Update: Read latency Aging control for IPU1/PRE0/PRE3 Aging control for IPU2/PRE1/PRE2 Test results: 3 boards passed overnight memtester stress test. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit b8625b732cfc59e44955f0e23b581e7896be1733)
* MLK-10504 imx: mx6dqarm2: Fix CCM setting for lpddr2 400Mhz supportYe.Li2015-04-29-0/+6
| | | | | | | | | | | | | | | | | | Current uboot supports for running LPDDR2 at 400MHz on MX6Q ARM2 board, but there is a problem in switching pre_periph_clk_sel to pll2_pfd2. We cannot directly change the parent of pre_periph_clk_sel as this mux is not a glitchless mux. We need to follow the correct procedure and wait for the busy bits to clear before switching. Change to follow the procedure: 1. Set periph_clk2 to OSC. 2. Switch the periph_clk to periph_clk2, checking the CCM_CDHIPR for periph_clk , ahb_podf and axi_podf busy bits. 3. Setting the pre_periph_clk to PLL2 PFD 396M. 4. Switch the periph_clk back to pre_periph_clk and checking CCM_CDHIPR busy bits. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 7490062ff86e1132b95bf153091f28f7940c0cf9)
* MLK-10658 imx: mx7d 12x12 arm2: Update plugin codes to use latest DDR scriptYe.Li2015-04-29-23/+27
| | | | | | | | | | The LPDDR3 intialization in plugin codes were missed to update in previous DDR script upgrading. So update the plugin codes to LPDDR3 script: 7D_lpddr3_0_2.ds5 Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 1874cec3a70adde2ea911a9c155fb41c43ccab61)
* MLK-10655 Video: Fix second line string display issueYe.Li2015-04-29-4/+5
| | | | | | | | | | The string display on second line repeats the last word of first line and does not show full. This is the bug introduced by the fixing to MLK-10542. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit ac430cee8c42f0acad9e126631d772b99f1166ea) (cherry picked from commit ff62c5b275a9b5e47d570d3eb10622799bf12070)
* MLK-10647 armv7: Fix Dcache disable issue on i.MX7Ye.Li2015-04-29-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The issue on the i.MX7D is that, there is one cache-able memory access between the L1 and L2 cache flush by calling the flush_dache_all-> v7_maint_dcache_all() [Flush L1 and L2 cache) which written in the C code. L1-cache-flush -> This will flush L1 cache to L2 cache in the end. Cache-able memory access -> This will have the chance cause the L1 line-fill with dirty data from L2 cache(L1 cache-line dirty, L2 clean) L2-cache-flush -> This will only flush L2 cache to L3, but still some dirty data on the L1 cacheline. After C & M bit clean, -> The dirty data on the L1 cache line lost, which will cause memory coherent issue if that dirty cache line has some useful data The only problem here is: there is one cache-cable memory access between L1 and L2 cache flush. This patch should works fine on the i.MX6 and i.MX7. The second cache flush have zero impact on the i.MX6, but this is really need for the i.MX7D platform due to the L1 line-fill during the first dcache_flush. And the second flush will not bring in the L1 dirty cache line due to the C bit is clear now, which means the dcache is disabled. Acked-by: Jason Liu<r64343@freescale.com> Reviewed-by: Jason Liu<r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit f5d5f07fba936c4bb05c887de9d72fb75b3dc0f2) (cherry picked from commit 86c784cf4c4b633d37a76de7d47155c08f75dc82)
generated by cgit v1.1 at 2024-12-18 02:21:22 +0000