summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* tricorder: add led supportAndreas Bießmann2013-11-01-6/+100
| | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: panic() on unknown boardAndreas Bießmann2013-11-01-0/+84
| | | | | | Also hang() the board on panic(). Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: add tricordereeprom commandAndreas Bießmann2013-11-01-1/+300
| | | | | | | The new tricordereeprom command can read and write the eeprom for hardware detection on tricorder devices. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: add mtdparts to environmentAndreas Bießmann2013-11-01-5/+4
| | | | | | | | Before we always ran 'mtdparts default' which also set the mtdparts and mtdids environment. But if we changed that values by intention we will overwrite them with our default values. This is obviously bad! Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: add cmdline historyAndreas Bießmann2013-11-01-15/+57
| | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: add configuration for a flashcard u-bootAndreas Bießmann2013-11-01-0/+1
| | | | | | | The 'flashcard' u-boot configuration has a readonly environment and boots a bare kernel/initrd to program the device from an clean environment. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: use generic provided loadaddrAndreas Bießmann2013-11-01-1/+4
| | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: update flash partitioningAndreas Bießmann2013-11-01-18/+22
| | | | | | | | | The new flash layout respects posible bad blocks in sectors reserved for e.g. SPL, u-boot, kernel, env a.s.o. Additionally this patch prepares for U-Boot Falcon mode for boot time saving. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* tricorder: remove lcdmode from bootargsThomas Weber2013-11-01-4/+1
| | | | | Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* arm, da85x: update for the ipam390 boardHeiko Schocher2013-11-01-34/+32
| | | | | | | | | | | | - switch to correct ecc layout used by the RBL enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC - update default environment - change A2CR to correct value for UART boot mode - adapt cs3cfg timings for nand - change LED bootmode signalization Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
* nand, davinci: add special UBL ecc positionHeiko Schocher2013-11-01-0/+12
| | | | | | | | | | | | enable the RBL/UBL ECC layout through CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define see for more info: http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com>
* ARM: OMAP4: Convert to ti_armv7_common.hLokesh Vutla2013-11-01-165/+27
| | | | | | | | | | Update omap4_common.h to use ti_armv7_common.h Testing: * Boot tested on OMAP4430 ES2.1 OMAP4460 ES1.1 SDP, OMAP4 PANDA/PANDA ES * Verified ./MAKEALL -s omap Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP3: igep00x0: rename config file to omap3_igep00x0.hJavier Martinez Canillas2013-11-01-5/+5
| | | | | | | | | | | | | | There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEPv2 board and the IGEP COM Module use a TI OMAP35xx/DM37xx processor, is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
* ARM: IGEP0033: rename config file to am335x_igep0033.hJavier Martinez Canillas2013-11-01-1/+1
| | | | | | | | | | | | | There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEP COM AQUILA use a TI AM335x processor is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
* TI:am33xx: Add bootcount support to ti_am335x_common.hTom Rini2013-11-01-0/+8
| | | | | | | Enable the bootcount driver for am335x in general. We leave adding a bootlimit and altbootcmd to the environment to the board ports. Signed-off-by: Tom Rini <trini@ti.com>
* bootcount_davinci: Switch to scratch register #2Tom Rini2013-11-01-4/+6
| | | | | | | | The RTC IP block here provides 3 scratch registers. Currently when using DeepSleep on am335x the scratch0/1 registers are used so moving ourself to scratch2 makes cooperation easier. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini2013-11-01-53/+59
| | | | | | | Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
* drivers/rtc/davinci.c: Reference DAVINCI_RTC_BASE more directlyTom Rini2013-11-01-3/+3
| | | | | | We shouldn't rely on a define to hide this cast for us. Signed-off-by: Tom Rini <trini@ti.com>
* arm: Remove IXP425 boards pdnb3 and scpuStefan Roese2013-10-17-775/+3
| | | | | | | | | | Remove Prodrive pdnb3 board (including the scpu variant) support from mainline. As its unmaintained and not needed any more for quite some time. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* zynq: Use arch_cpu_init() instead of lowlevel_init()Michal Simek2013-10-17-0/+6
| | | | | | | | | | | Zynq lowlevel_init() was implemented in C but stack pointer is setup after function call in _main(). Move architecture setup to arch_cpu_init() which is call as the first function in board_init_f() which already have correct stack pointer. Reported-by: Sven Schwermer <sven.schwermer@tuhh.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* Prepare v2013.10Tom Rini2013-10-16-1/+1
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* microblaze: Fix watchdog initializationMichal Simek2013-10-16-8/+5
| | | | | | | | | | | The patch: "blackfin: Move blackfin watchdog driver out of the blackfin arch folder." (sha1: e9a389a18477c1c57a0b30e9ea8f4d38c6e26e63) changed hw_watchdog_init() prototype which didn't match with Microblaze one. This patch fixes the driver and Microblaze initialization. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* common: fsl: Fix broken SPDX-License-Identifier changeMichal Simek2013-10-16-4/+4
| | | | | | | | This bug was introduced by: "Add GPL-2.0+ SPDX-License-Identifier to source files" (sha1: 1a4596601fd395f3afb8f82f3f840c5e00bdd57a) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* mtd: fix warnings due to 64-bit partition supportScott Wood2013-10-15-4/+5
| | | | | | | | | | | | | | | commit 39ac34473f3c96e77cbe03a49141771ed1639486 ("cmd_mtdparts: use 64 bits for flash size, partition size & offset") introduced warnings in a couple places due to printf formats or pointer casting. This patch fixes the warnings pointed out here: http://lists.denx.de/pipermail/u-boot/2013-October/164981.html Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Tom Rini <trini@ti.com>
* spi: mxc_spi: Fix double incrementing read pointer for unaligned buffersTimo Herbrecher2013-10-16-1/+1
| | | | | | | | If dout buffer is not 32 bit-aligned or data to transmit is not multiple of 32 bit the read data pointer is already incremented on single byte reads. Signed-off-by: Timo Herbrecher <t.herbrecher@gateware.de> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* sf: probe: Add missing Atmel at25df321 flashBo Shen2013-10-16-0/+1
| | | | | | | | | As the spi flash transfer to multiple parts, it is forgot to add Atmel AT25DF321 spi flash support, which broken several Atmel EK boards which this chip. So, add it Signed-off-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* spi: Add GPL-2.0+ SPDX-License-Identifier for missing filesJagannadha Sutradharudu Teki2013-10-16-5/+5
| | | | | | | Added GPL-2.0+ SPDX-License-Identifier for missed spi source files. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* sf: Add GPL-2.0+ SPDX-License-Identifier for missing onesJagannadha Sutradharudu Teki2013-10-16-5/+6
| | | | | | | | Added GPL-2.0+ SPDX-License-Identifier for missed sf source files. Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Bo Shen <voice.shen@atmel.com>
* sf: Minor cleanups.Jagannadha Sutradharudu Teki2013-10-16-13/+14
| | | | | | | | | - Add comments. - Renamed few macros. - Add tabs. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Bo Shen <voice.shen@atmel.com>
* sf_ops: Unify bank_sel calculation codeJagannadha Sutradharudu Teki2013-10-16-16/+20
| | | | | | | Unified the bank_sel calculation code for erase and write ops. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* buildman: Use env to pick the python from $PATHJagannadha Sutradharudu Teki2013-10-15-1/+1
| | | | | | | | | | | python used in buildman doesn't need to be placed in /usr/bin/python, So use env to ensure that the interpreter will pick the python from environment. Usefull with several versions of python's installed on system. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
* Merge branch 'buildman' of git://git.denx.de/u-boot-x86Tom Rini2013-10-14-1/+2
|\
| * buildman: don't fail --list-toolchains when toolchains failStephen Warren2013-10-10-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a toolchain invocation fails, an exception is thrown but not caught which then aborts the entire toolchain detection process. To solve this, request that exceptions not be thrown, since the toolchain init code already error-checks the command result. This solves e.g.: - found '/usr/bin/winegcc' Traceback (most recent call last): ... Exception: Error running '/usr/bin/winegcc --version' Change-Id: I579c72ab3b021e38b14132893c3375ea257c74f0 Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> (formatted to 80cols)
* | cmd_sandbox.c: Update for do_(load|save) not taking a number baseTom Rini2013-10-14-2/+2
| | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
* | Prevent null pointer dereference originating in cmd_pxe.cSteven Falco2013-10-14-42/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to avoid possible crashes due to null pointer dereferencing. Commit d7884e047d08447dfd1374e9fa2fdf7ab36e56f5 does not go far enough. There is still at least one call chain that can result in a crash. The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid cmdtp. Passing in NULL is particularly bad in the do_tftpb() case, because eventually boot_get_kernel() will be called with a NULL cmdtp: do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm() -> do_bootm_states() -> bootm_find_os() -> boot_get_kernel() Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the null pointer, and the board will crash. Signed-off-by: Steven A. Falco <stevenfalco@gmail.com>
* | Coding Style cleanup: drop some excessive empty linesWolfgang Denk2013-10-14-46/+0
| | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | Coding Style cleanup: remove trailing empty linesWolfgang Denk2013-10-14-18/+0
| | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | Coding Style cleanup: replace leading SPACEs by TABsWolfgang Denk2013-10-14-506/+506
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
* | Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-14-640/+640
| | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | ARM: omap4-panda: Add MAC address creation for pandaDan Murphy2013-10-14-0/+20
| | | | | | | | | | | | | | | | Add a MAC address create based on the OMAP die ID registers. Then poplulate the ethaddr enviroment variable so that the device tree alias can be updated prior to boot. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | pmic: max77686: fix the wrong offsetJaehoon Chung2013-10-14-1/+1
| | | | | | | | | | | | 0x1D is reserved. So BUCK3DVS1 is started from 0x1e. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* | env_mmc: fix buffer allocation for armv7Markus Niebel2013-10-14-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit d196bd880347373237d73e0d115b4d51c68cf2ad adds redundand environment to mmc. The usage of malloc in env_relocate_spec triggers cache errors on armv7. Tested on a not mainlined i.MX53 board: Board: TQMa53 I2C: ready DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57c2d8 ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f57e2d8 ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57e2e0 ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f5802e0 Using default environment Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
* | env: dataflash: fix env_init issueBo Shen2013-10-14-32/+18
| | | | | | | | | | | | | | | | | | | | | | | | As the SPI controller is not initialized before env_init(), it causes reading env in dataflash failed. So, although saveenv() successfully, it shows warning information when reboot the system as following: *** Warning - bad CRC, using default environment Let the env_relocate() to check env CRC and import it. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* | ARM: omap4: Update sdram setting for panda rev A6Dan Murphy2013-10-14-0/+4
| | | | | | | | | | | | | | | | | | | | OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory part. The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron so the timings needs to be updated Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | am335x_evm.h: Make 'am335x_boneblack' use redundant environmentTom Rini2013-10-14-0/+3
| | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
* | .gitignore: add auto-generated /include/[s|t]pl-autoconf.mkDaniel Schwierzeck2013-10-14-0/+2
| | | | | | | | Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* | SPDX: document dual license notationWolfgang Denk2013-10-14-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | In [1] we discussed how we should deal with dual (or, more generally, multiple) licensed files. Add this to Licenses/README so it's properly documented. [1] http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/166518 Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Add the word 'list' to the end of the line, per Stephen Warren's feedback] Signed-off-by: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-14-0/+1449
|\ \
| * \ Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-10-11-0/+1449
| |\ \
| | * | samsung: trats2: add support for new board Trats2Piotr Wilczek2013-09-25-0/+859
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add support for a new Samsung board Trats2. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit v1.1 at 2024-09-19 10:44:36 +0000