summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2014-11-26-71/+335
|\
| * arm: ls102xa: Select ge2_clk125 for eTSEC clock muxingAlison Wang2014-11-24-0/+1
| | | | | | | | | | | | | | | | | | | | EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1 as other functionality except RGMII. The workaround is to select ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR boardAlison Wang2014-11-24-2/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SystemID information could be read through I2C1 from EEPROM on LS1021ATWR board. As LS1 is a little-endian processor, getting the version ID by be32_to_cpu() is wrong. Fix it by using e.version directly. This change will be compatible for both ARM and PowerPC. As there is an errata that I2C1 could not work in SD boot, reading EEPROM through I2C1 is disabled too in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * ls102xa: ifc: nor: fix the write issue when bytes unalignedYuan Yao2014-11-24-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Add define CONFIG_SYS_WRITE_SWAPPED_DATA. For LS1021AQDS and LS1021QTWR nor flash write should swap the bytes when handle unaligned tail bytes. Because of the ending, if the date bus width is 16-bits and the number of bytes is odd, we should swap the byte when write the last one. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Remove bit reversing for SCFG registersAlison Wang2014-11-24-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SCFG_SCFGREVCR is SCFG bit reverse register. This register must be written with 0xFFFFFFFF before writing to any other SCFG register. Then other SCFG register could be written in big-endian mode. Address: 157_0000h base + 200h offset = 157_0200h Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 W/R SCFGREV Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0-31 SCFGREV SCFG Bit Reverse Control Filed 32'h 0000_0000 - No bit reverse is applied 32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as 0:31 This patch removes the bit reversing for SCFG registers in u-boot. It will be implemented through PBI commands in RCW .pbi write 0x570200, 0xffffffff .end So other SCFG register could be written in big-endian mode in u-boot or kernel directly. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Add snoop disable for slave port 0, 1 and 2Jason Jin2014-11-24-0/+18
| | | | | | | | | | | | | | | | | | Disable the snoop for slave interface 0, 1 and 2 to avoid the interleaving on the CCI400 BUS. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * ls1: config: Enable USB EHCI Host on LS1021AQDSNikhil Badola2014-11-24-0/+17
| | | | | | | | | | | | | | Enable USB EHCI Host on LS1021AQDS Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * drivers: usb: fsl: Define USB configs for LS102XANikhil Badola2014-11-24-0/+7
| | | | | | | | | | | | | | | | Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR, CONFIG_USB_MAX_CONTROLLER_COUNT Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * drivers : usb: fsl: Implement usb Erratum A007798 workaroundNikhil Badola2014-11-24-2/+17
| | | | | | | | | | | | | | | | Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large usb writes Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * drivers: usb: fsl: Move USB Errata checking codeNikhil Badola2014-11-21-56/+68
| | | | | | | | | | | | | | | | | | | | Move USB Errata checking code from "arch/powerpc" to architecture independent file "fsl_usb.h" so that errata(s) become independent of the architecture. For each erratum checking function for PPC arch, define a nop function for non PPC arch for successful compilation in either case Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * u_qe: add u_qe_upload_firmware for u_qeZhao Qiang2014-11-19-2/+131
| | | | | | | | | | Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Fixed a register definition errorTang Yuantian2014-11-19-1/+1
| | | | | | | | | | | | | | There are 8 SCFG_SPARECR registers in SCFG memory block, not one. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support for ls1021a-twr boardZhao Qiang2014-11-19-0/+14
| | | | | | | | | | Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support to ls1021aqdsZhao Qiang2014-11-19-0/+15
| | | | | | | | | | | | | | add qe support to ls1021aqds Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add u-qe support to arm boardZhao Qiang2014-11-19-1/+33
| | | | | | | | | | | | | | | | | | ls1021 is arm-core and support qe which is u-qe. add u-qe init for arm board. Signed-off-by: Zhao Qiang <B45475@freescale.com> [York Sun: Fix compiling error caused by u_qe_init()] Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-11-26-15/+523
|\ \ | | | | | | | | | | | | | | | | | | Conflicts: drivers/mmc/fsl_esdhc.c Signed-off-by: Tom Rini <trini@ti.com>
| * | mmc: fsl_esdhc: fix f_max retrieval during initMarkus Niebel2014-11-19-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | for multi instance API we use struct fsl_esdhc_cfg to pass the clock rate. Do not set f_max from global data, since this is wrong for multi instance case. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Eric Nelson <eric.nelson@boundarydevices.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | net/fm: add 2.5G SGMII supportShengzhou Liu2014-11-19-4/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As auto-negotiation is not supported for 2.5G SGMII, we need to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate SGMII-1G and SGMII-2.5G with different setting for auto-negotiation. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc/t2080qds: fix for 1000BASE-KXShaohui Xie2014-11-19-0/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX mode. By default, the lane runs in SGMII mode, when a MAC uses a lane in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set, and needs to fixup dtb accordingly for kernel to do proper initialization. Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC 1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx", 'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc. If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below setting: fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> [York Sun: Fix compiling warning] Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc/t2080qds: fixup dtb for 10g-krshaohui xie2014-11-19-11/+98
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | XFI ports on t2080qds can work with fiber cable and direct attach cable(copper). We use hwconfig to define cable type for XFI, and fixup dtb based on the cable type. For copper cable, set below env in hwconfig: fsl_10gkr_copper:<10g_mac_name> the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4. fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3 stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if a given 10G port will use the copper cable for 10GBASE-KR, set the <10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be assumed to be used for the port. For ex. if four XFI ports will both use copper cable, the hwconfig should contain: fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | config: MPC837X : Add complete USB EHCI supportNikhil Badola2014-11-19-0/+10
| | | | | | | | | | | | | | | | | | | | | Add complete USB EHCI support for MPC837XEMDS and MPC837XERDB Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc/t4rdb: Fix CPLD timingChunhe Lan2014-11-19-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes CPLD timing from previous commit ab06b236f76cfa42f264ee161be190b3e479298f. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> [York Sun: This is the difference between v2 and v1 patch] Reviewed-by: York Sun <yorksun@freescale.com>
| * | board/t2080qds: add readme for t2080qdsShengzhou Liu2014-11-19-0/+243
| | | | | | | | | | | | | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | P1023RDB: Update default environmentChunhe Lan2014-11-19-0/+43
| |/ | | | | | | | | Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | spl: Fix SPL EXT supportGuillaume GARDET2014-11-26-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | Commit 9f12cd0e062614e19734b2ab37842d387457c5e5 has broken SPL EXT support. This patch update error code check to get SPL EXT support working again. Tested on a Pandaboard (rev. A3). Reviewed-by: Suriyan Ramasami <suriyan.r@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com>
* | Merge branch 'master' of http://git.denx.de/u-boot-samsungTom Rini2014-11-26-87/+787
|\ \
| * | ORIGEN: Enhance origen config to be more flexible on boot.Guillaume GARDET2014-11-25-1/+34
| | | | | | | | | | | | | | | | | | | | | | | | This patch enhances the boot of origen board by adding support to ext2, bootz, initrd, bootenv loading and boot script. It still keeps the previous mmc load command if boot script fails. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | odroid: Turn blue LED onSuriyan Ramasami2014-11-24-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | To indicate that U-Boot is active, turn on the blue LED. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | odroid: usbhost - Add missing gpio_request callSuriyan Ramasami2014-11-24-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The USB host code was missing gpio_request() calls before using the gpio functions, causing errors to be printed out. As a side note calls to max77686_set_buck_mode(OPMODE_OFF/OPMODE_ON) have been removed, as they did not have any effect. This is as per Przemyslaw: I looked into the documentation and there is a "ENB8" pin in PMIC package. This pin allows steering BUCK8 ON/OFF by the hardware. If ENB8 is set to low then you can do on/off. If high, then you cannot change its state by I2C write, which seems to be the case with the Odroids. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | odroid: Update README with USB host usageSuriyan Ramasami2014-11-24-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add information wrt using the USB host interface for loading kernel over ethernet and/or usb mass storage. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | arm: odroid: usb: add support for usb host including ethernetSuriyan Ramasami2014-11-17-8/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | This change adds support for enabling the USB host features of the board. This includes the USB3503A hub and the SMC LAN9730 ethernet controller as well. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | arm: odroid: enable/disable usb host phy for exynos4412Suriyan Ramasami2014-11-17-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | Enable/disable the usb host phy on the odroid U/X2 boards which are based on the Exynos4412 SOC. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | arm: odroid: pmic77686: allow buck voltage settingsSuriyan Ramasami2014-11-17-3/+52
| | | | | | | | | | | | | | | | | | | | | | | | Allow to set the buck voltage for the max77686. This will be used to reset the SMC LAN9730 ethernet on the odroids. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | SMDK2410: convert to generic boardDavid Müller (ELSOFT AG)2014-11-17-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Compile-time tested only, as I currently don't have access to the eval board. Signed-off-by: David Müller <d.mueller@elsoft.ch> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | exynos: dts: Correct USB vbus-gpio numbering for SnowSjoerd Simons2014-11-17-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current vbus GPIOs on snow make very little sense, their number is far above the maximum. As a result, USB doesn't work on snow. Correct the GPIO numbering so they match the current scheme for exynos5. Tested both EHCI and XHCI to correctly work after this change. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | exynos: Increase command line buffer size (CONFIG_SYS_CBSIZE)Ian Campbell2014-11-17-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I was running into this limit with a not overly long PXE append line. Since the PXE code wants to print the resulting command line increase CONFIG_SYS_PBSIZE too. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | exynos5: Use config_distro_bootcmd.hIan Campbell2014-11-17-22/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This replaces the existing CONFIG_BOOTCOMMAND for exynos5250 and 5420. exynos4 platforms seem to have existing complex extra env configuration for booting and so are excluded here. Hence the bootcmd.h is added to exynos5-common.h. I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot tested on arndale. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Guillaume GARDET <guillaume.gardet@free.fr> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | exynos: Enable config_distro_defaults.hIan Campbell2014-11-17-24/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ...and remove explicit setting of things which this implies. This is done for all exynos platforms (4 & 5) so it is added to exynos-common.h I'm mainly interested in CONFIG_CMD_BOOTZ and CONFIG_SUPPORT_RAW_INITRD I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot tested on arndale. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Guillaume GARDET <guillaume.gardet@free.fr> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Peach-Pi: Use the enhanced usb_copy() prototypeVadim Bendebury2014-11-17-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Exynos5800 IROM has a different, from 5250 and 5420, prototype of the usb_copy() function. Luckily the earlier version did not expect any arguments, which means the same code could be used with old and new SoCs, the old ones just ignoring the arguments. Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos5: ddr3: Choose between single or double channel configAkshay Saraswat2014-11-17-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a 4G configuration and choose it based on the number of banks declared in config file. A board with 4 SDRAM banks declared (as per CONFIG_NR_DRAM_BANKS) will end up with the 2G confiuration. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Config: Exynos5420: Refactor SDRAM Bank and SizeAkshay Saraswat2014-11-17-4/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since, not every board may have all memory channels configured and all available banks of DMC used, we wish to refactor configs for Memory Bank size and numbers as per board memory config. For Example, Peach-Pit has 2GB memory and will be using only 4 banks but Peach-Pi has 3.5GB memory and will be using all 7 available SDRAM banks. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | DMC: Exynos5: Enable update mode for DREX controllerAlim Akhtar2014-11-17-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As per Exynos5800 UM ver 0.00 section 17.13.2.1 CONCONTROL register bit 3 [update_mode], Exynos5800 does not support the PHY initiated update. And it is recommanded to set this field to 1'b1 during initialization. This patch sets this bit. Applying MC-initiated mode makes DDL tracking ON, that helps in compensate MIF voltage variation. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Config: Exynos5800: Enable build for Peach-PiAkshay Saraswat2014-11-17-4/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds following things : - New config and defconfig for Peach-Pi board. - Alterations in Kconfig and MAINTAINERS. - Addition of CONFIG_EXYNOS5800. - ADdition of exynos5800-peach-pi in dts list. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos5800: Add DTS for new board Peach-PiAkshay Saraswat2014-11-17-1/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have a new board Peach-Pi similar to Peach-Pit. Peach-Pi differs from Peach-Pit in configuration factors like display resolution, memory size, SoC version etc. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos5800: Introduce new proid for Exynos5800Akshay Saraswat2014-11-17-14/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch intends to add a new proid for Exynos5800 which is a variant of Exynos5420. Product id for Exynos5800 is 0x5422. Both Exynos5420 and Exynos5800 are pin to pin compitable. This gives us an advantage of reusing Exynos5420 clock, pinmux, memory and other settings. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2014-11-26-53/+1032
|\ \ \
| * | | sun7i: Set ARMV7_BOOT_SEC_DEFAULT when OLD_SUNXI_KERNEL_COMPAT is setHans de Goede2014-11-25-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Old kernels cannot handle booting in non-secure (hyp) mode, so when OLD_SUNXI_KERNEL_COMPAT is set, also set ARMV7_BOOT_SEC_DEFAULT. Note that whether to booting secure or non-secure can always be overriden using the bootm_boot_mode environment variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | sun7i: Drop CONFIG_ARMV7_PSCI_NR_CPUSHans de Goede2014-11-25-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | It is not used anywhere. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | sun6i: Drop some "unknown magic" from dram initHans de Goede2014-11-25-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allwinner tells us that this bit of code is the rtc ram being used to detect coming out of "super-standby" mode, and if that is the case, going out of self-refresh mode. Since we do not support "super-standby" mode, this can be dropped. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | sun6i: Add gmac support for sun6i boardsHans de Goede2014-11-25-1/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hookup the gmac found on the sun6i / A31 SoCs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>