summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* net, davinci_emac: let the EMAC detect the PHYsHeiko Schocher2011-09-30-0/+3
| | | | | | | | | | | Once the MDIO state machine has been initialized and enabled, it starts polling all 32 PHY addresses on the MDIO bus, looking for an active PHY. Add a 5 ms delay, so all PHYs are for sure detected. This problem was detected on the cmc board with a KSZ8864 switch. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* net, davinci_emac: make less verbose - turn printf() into debug()Heiko Schocher2011-09-30-1/+1
| | | | | | | | | | | | | | | | | | | | The PHY driver was too verbose and corrupted the boot message display like this: ... Net: Ethernet PHY: KSZ8873 @ 0x02 DaVinci-EMAC ... Turn printf() into debug() so we get the expected output again: ... Net: DaVinci-EMAC ... Signed-off-by: Heiko Schocher <hs@denx.de> cc: Paulraj Sandeep <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* net, davinci_emac: add KSZ8864 switchHeiko Schocher2011-09-30-1/+82
| | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* i2c, davinci: add i2c set speedHeiko Schocher2011-09-30-0/+5
| | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Devkit8000: Change console from ttyS2 to ttyO2Thomas Weber2011-09-30-1/+1
| | | | | | | | The omap serial names have changed from ttySx to ttyOx, so the console should be also changed to support this. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: update maintainer for omap4 boardsAneesh V2011-09-30-2/+5
| | | | | | | | | | | | Steve wants to transfer maintainership of OMAP4 boards to me as he is not working on these boards lately. CC: Steve Sakoman <steve@sakoman.com> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Albert Aribaud <albert.u.boot@aribaud.net> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap3evm: env: Fix default consoleSanjeev Premi2011-09-30-1/+1
| | | | | | | | | Change the default console from ttyS2 to ttyO0 to match the Linux default for the EVM. Signed-off-by: Sanjeev Premi <premi@ti.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap3: Fix compile warningSanjeev Premi2011-09-30-1/+1
| | | | | | | | | | Building without option CONFIG_DISPLAY_CPUINFO leads to this warning: sys_info.c:50:14: warning: 'rev_s_37xx' defined but not used Signed-off-by: Sanjeev Premi <premi@ti.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* mmc: omap: config VMMC, MMC1_PBIASBalaji T K2011-09-30-4/+49
| | | | | | | | | | Config VMMC voltage to 3V for MMC/SD card slot and PBIAS settings needed for OMAP4 Fixes MMC/SD detection on boot from eMMC. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* mmc: omap: enable high capacityBalaji T K2011-09-30-1/+2
| | | | | | | | | | Enable high capacity to host capability. Fixes eMMC detection on boot from MMC/SD card. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* devkit8000: Fix build breakSandeep Paulraj2011-09-30-1/+1
| | | | | | | Found a build erros when i ran MAKEALL. So fix it. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap-common: reorganize spl.cSimon Schwarz2011-09-30-177/+247
| | | | | | | | | | split-up spl.c into spl.c, spl_mmc.c and spl_nand.c. This avoids problems with missing defines if a board does not use mmc or nand. This includes adding spl_ prefix to some functions which are now public. spl_image_t is now a public type. Added some of the common functions to omap-common.h Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap3: implement boot parameter savingSimon Schwarz2011-09-30-3/+12
| | | | | | | Implements the saving of boot params passed by OMAP3 ROM code. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* devkit8000: Add nand-spl support for new SPLSimon Schwarz2011-09-30-1/+47
| | | | | | | Add NAND SPL support to the devkit8000 config Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap3: new SPL structure supportSimon Schwarz2011-09-30-0/+36
| | | | | | | | Support for the new spl structure. Using the interface defined by Aneesh V for OMAP4 Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* spl: Add POWER library to new splSimon Schwarz2011-09-30-0/+2
| | | | | | | Adds power library to the new spl Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* spl: add NAND Library to new SPLSimon Schwarz2011-09-30-5/+288
| | | | | | | | Adds NAND library to SPL. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap-common: add nand spl supportSimon Schwarz2011-09-30-3/+127
| | | | | | | Add NAND support for the new SPL structure. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap3: Configure RAM bank 0 if in SPLSimon Schwarz2011-09-30-1/+67
| | | | | | | | | | OMAP3 relied on the memory config done by X-loader or Configuration Header. This has to be reworked for the implementation of a SPL. This patch configures RAM bank 0 if CONFIG_SPL_BUILD is set. Settings for Micron-RAM used by devkit8000 are added to mem.h Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap-common/omap4: relocate early UART clock setupSimon Schwarz2011-09-30-1/+2
| | | | | | | | | | | | | | | Moves the early UART clock setup setup_clocks_for_console() from preloader_console_init() to s_init() of OMAP4. This is done to prepare for OMAP3 integration. This patch was posted seperatly to the mailinglist but I decidet - since it is a prereqesit for this patch to add it. Former port to ML: http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395 Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* overo: Set IEN on GPMC_CLK to support synchronous clocking.Philip Balister2011-09-30-1/+1
| | | | | | | | Without this change CS's configured for synchronous clocking cannot read data. Signed-off-by: Philip Balister <philip@opensdr.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: Overo: Update GPMC timing for ethernet chipPhilip Balister2011-09-30-18/+11
| | | | | | | | | | The existing timing does not quite meet the minimum requirements in the LAN9221 datasheet. The timing in this patch solves problems noticed on some parts. The patch also combines the CS configuration for the overo and igep0020 boards per request. Signed-off-by: Philip Balister <philip@opensdr.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Armada100: Enable 88E3015 PHY support for GplugDAjay Bhargav2011-09-30-0/+47
| | | | | | | | This patch adds support for 88E3015 PHY for Marvell GplugD board. This patch depends on series of patch which adds support for Marvell GuruPlug-Display. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* Armada100: Enable Ethernet support for GplugDAjay Bhargav2011-09-30-2/+128
| | | | | | | This patch enables ethernet support for Marvell GplugD board. Network related commands works. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* net: Adds Fast Ethernet Controller driver for Armada100Ajay Bhargav2011-09-30-0/+971
| | | | | | | | This patch adds support for Fast Ethernet Controller driver for Armada100 series. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* omap4_panda: Ignore omap4 SPL called MLOJoe Hershberger2011-09-30-0/+1
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Sandeep Paulraj <s-paulraj@ti.com>
* gpio: Add GPIO driver for Marvell SoC Armada100Ajay Bhargav2011-09-30-0/+48
| | | | | | | This patch adds support for generic GPIO driver framework for Marvell SoC Armada100. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* gpio: Add GPIO driver framework for Marvell SoCsAjay Bhargav2011-09-30-0/+190
| | | | | | | | | This patch adds generic GPIO driver framework support for Marvell SoCs. To enable GPIO driver define CONFIG_MARVELL_GPIO and for GPIO commands define CONFIG_CMD_GPIO in your board configuration file. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* Prepare v2011.09v2011.09Wolfgang Denk2011-09-29-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: versatile: delete split_by_variant.shLinus Walleij2011-09-28-42/+0
| | | | | | | | | Since commit d388298a59ba375c76597b8f95b560afa971a0fb by Stefano Babic this file is no longer needed so delete it. Cc: Stefano Babic <sbabic@denx.de> Cc: Loïc Minier <loic.minier@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Revert "phylib: remove a couple of redundant code lines"Wolfgang Denk2011-09-28-2/+5
| | | | | | | | | | | | | | | | | | | | | | This reverts commit 041c542219af7f31c372d89b4c7c6f4c8064a8ce. The lines removed by this commit weren't redundant. The logic is (and probably should be better commented): Find the intersection of the advertised capabilities of both sides of the link (lpa). From that intersection, find the highest capability we can run at (that will be the negotiated link). Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL). The code will now set phydev->speed to 100, and phydev->duplex to 1, but this link does not support 100FULL. Kudos to Andy Fleming <afleming@gmail.com> for binging this to attention and for the explanation. Signed-off-by: Wolfgang Denk <wd@denx.de>
* doc/README.scrapyard: Update board removal commit IDsWolfgang Denk2011-09-28-13/+13
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-09-28-816/+2
|\ | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: ARM: remove broken "ixdp425" and "ixpdg425" boards
| * ARM: remove broken "ixdp425" and "ixpdg425" boardsAlbert ARIBAUD2011-09-27-816/+2
| | | | | | | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Stefan Roese <sr@denx.de>
* | ASIX: Fix buffer access in asix_get_phy_addr()Marek Vasut2011-09-24-1/+1
|/ | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-09-23-1/+1
|\ | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: OMAP3: beagle: Fix build warning in beagle.c
| * OMAP3: beagle: Fix build warning in beagle.cDirk Behme2011-09-22-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix build warning beagle.c:532: warning: initialization from incompatible pointer type Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Koen Kooi <koen@dominion.thruhere.net> CC: Joel A Fernandes <agnel.joel@gmail.com> Cc: Greg Turner <gregturner@ti.com> CC: Sandeep Paulraj <s-paulraj@ti.com> Acked-by: Jason Kridner <jkridner@beagleboard.org>
* | doc: provide a correct board_init_r definition pathVladimir Zapolskiy2011-09-23-1/+1
|/ | | | | | | | This is a trivial fix in the documentation, which corrects board_init_r() source reference. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
* Prepare v2011.09-rc2v2011.09-rc2Wolfgang Denk2011-09-22-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Minor Coding Style CleanupWolfgang Denk2011-09-22-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* km/common: fix bug in IVM mac address accessHolger Brunck2011-09-21-2/+2
| | | | | | | | The MAC address stored in the inventory eeprom begins at offset 1. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* sf: fix debug format string warningVadim Bendebury2011-09-21-1/+1
| | | | | | | | On some systems, we get a warning when %lu is used with size_t's, so use the correct format string. Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* net: turn name len check into an assertMike Frysinger2011-09-21-6/+1
| | | | | | | | | The new sanity check introduces a printf warning for some systems: eth.c:233: warning: format '%zu' expects type 'size_t', but argument 3 has type 'int' Rather than tweak the format string, use the new assert() helper instead. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* ignore soc asm-offsets.sMike Frysinger2011-09-21-0/+1
| | | | | | | | Recent commit a4814a69d3bca6ee05f4bfc4 cleaned up generation of asm-offsets.s for SoC dirs, but missed adding it to the ignore list which makes it show up in `git status`. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Drop bogus BOOTFLAG_* definitionsWolfgang Denk2011-09-20-11/+0
| | | | | | | | | | There is no code anywhere that references BOOTFLAG_* so remove these defines. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Peter Tyser <ptyser@xes-inc.com>
* net/bootp.c: fix tftp load if autoload environment var isn't setPeter Korsgaard2011-09-19-1/+1
| | | | | | | | | | | | | Commit 093498669 (Put common autoload code into auto_load() function) broke handling of autoload environment variable not being set. The bootp/dhcp code will just keep on requesting IP address forever and never start TFTP download. Fix it by moving TftpStart() outside the conditional like it was before. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
* ppc4xx: Flush dcache after DDR2 autocalibration with caches onStefan Roese2011-09-19-0/+7
| | | | | | | | Flush the dcache before removing the TLB with caches enabled. Otherwise this might lead to problems later on, e.g. while booting Linux (as seen on ICON-440SPe). Signed-off-by: Stefan Roese <sr@denx.de>
* Fix incorrect array size of phy settings for 405EXWeirich, Bernhard2011-09-19-1/+1
| | | | | | | | Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since 405EX has 2 ethernet interfaces. Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net> Signed-off-by: Stefan Roese <sr@denx.de>
* DA830: Fix Build WarningSandeep Paulraj2011-09-13-1/+2
| | | | | | This commit fixes a build warning in the DA830 EVM build Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* led: remove camel casing of led identifiers globallyJason Kridner2011-09-13-113/+113
| | | | | | | | | | | | | | | Result of running the following command to address Wolfgang's comment about camel case: for file in `find . | grep '\.[chS]$'`; do perl -i -pe 's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done Discussion: http://patchwork.ozlabs.org/patch/84988/ Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit v1.1 at 2024-11-05 05:09:28 +0000