summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* sf: probe: Fix quad bit set pathPoddar, Sourav2014-09-25-10/+10
| | | | | | | | | | Currently, flash quad bit is set in "spi_flash_validate_params" and later at the end in the same api, we write 0 to status register for few flashes, thereby overriding the quad bit set. This fix moves the quad bit setting outside this api in "spi_flash_probe_slave" Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* ENGR00332535 imx: mx6sx: Remove WEIM plugin work around for TO 1.2 and higherYe.Li2014-09-23-1/+7
| | | | | | | | ROM fixes the WEIM plugin issue in TO 1.2. The work around for hacking WEIM base address to ROM variable is not needed. To avoid hacking useful data, remove the work around for TO 1.2 and higher revisions. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00331269 arm: mx6: select OSC as uart's clk parentAnson Huang2014-09-18-0/+9
| | | | | | | | As M4 is sourcing UART clk from OSC, to make UART work when M4 is enabled, need to select OSC as clk parent, 24M OSC is enough for debug UART in uboot. Signed-off-by: Anson Huang <b20788@freescale.com>
* ENGR00331706-5 imx: mx6: Enable 24Mhz OSC for GPTYe.Li2014-09-18-0/+1
| | | | | | | Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that enable the 24Mhz OSC GPT on all MX6 platforms. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00331706-4 imx: mx6sl: Set the preclk clock source to OSC 24MhzYe.Li2014-09-18-0/+16
| | | | | | | For MX6SL, uses the OSC 24Mhz as the preclk source in CCM. Align the preclk setting with kernel. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00331706-3 imx: mx6: Change the get_ipg_per_clk for OSC 24Mhz sourceYe.Li2014-09-18-0/+4
| | | | | | | For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix the get_ipg_per_clk function to support it. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00331706-2 imx: mx6sl: Add perclk_clk_sel bit define in CCMYe.Li2014-09-18-0/+2
| | | | | | | The MX6SL has the perclk_clk_sel to select the perclk source. Add its define in CCM Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00331706-1 imx: gpt: Add 24Mhz OSC clock source support for GPTYe.Li2014-09-18-10/+66
| | | | | | | | | | | | | | | | Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set, the GPT will use 24Mhz OSC as clock source. Otherwise, the GPT will use 32Khz OSC as clock source. Since only the GPT on iMX6 series provide the clock source option for 24Mhz OSC. For other series(MX5), if the configuration is set, the perclk will be selected as clock source. MX6Q/D Rev 1.0 and MX6SL can't use the 24Mhz OSC clock source option, so select the perclk for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so eventually the clock comes from OSC 24Mhz. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00327364 iMX6: Ensure that the bandgap self-bias circuit is disabled ↵Ranjani Vaidyanathan2014-09-10-0/+24
| | | | | | | | | | | | after boot. The self-bias circuit is used by the bandgap during startup. Once the bandgap has stabilized, the self-bias circuit should be disabled for best noise performance of analog blocks. Also this bit should be disabled before the chip enters STOP mode or when ever the regular bandgap is disabled. Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
* ENGR00330792 imx: mx6: Merge anatop registers to CCM structureYe.Li2014-09-10-216/+160
| | | | | | | | | | THe anatop registers structure is duplicated with CCM structure at PLL fields. Since we are suggested not to use the name "anatop" any longer, merge the anatop registers to the CCM structure "mxc_ccm_reg" and use CCM to replace anatop. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00329484-2 ARM:MX6: Clear Align bit in SCTLRPeng Fan2014-09-05-0/+3
| | | | | | | | | | This problem is found when debugging QuadSPI. When "A" bit is enabled, unaligned access will cause data abort exception. Actually, we do not want this exception. So clear the align bit for MX6 SOCs. Tested this code with android team colleague and did not find problem. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00329484-1 QuadSPI:Unaligned access crash ubootPeng Fan2014-09-05-5/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To fsl_qspi_write_data and fsl_qspi_ip_read, pointer txbuf and rxbuf are not guaranteed that they are 4 Bytes aligned. Also, it it not a good idea to cast type 'u8 *' to 'u32 *', except we are sure that pointer type 'u8 *' is 4 Bytes aligned and cast it to 'u32 *' will not pass memory boundary. The problem is found when using fsl_qspi_write_data to write registers in flash devices. The err msg: data abort pc : [<87822f44>] lr : [<87822f38>] sp : bf5512c8 ip : 0000001c fp : bf856608 r10: 87868904 r9 : bf551efc r8 : 200f048c r7 : 00000002 r6 : bf551336 r5 : bf552a70 r4 : 00000001 r3 : 00000000 r2 : 00000060 r1 : 8783b520 r0 : 8783b520 Flags: nZCv IRQs on FIQs off Mode SVC_32 Resetting CPU ... The asm code which cause data abort is: 87822f30: e5964000 ldr r4, [r6] From the dump msg, r6 is not 4 Bytes aligned, and data abort exception. So, Use mempcy but not unsafe type casting. In this patch, max_write_size is assigned using txfifo to avoid possible errors in future. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00328278-1: Fix i.MX6DQ/DL arm2 LPDDR2 boards mem sizeNitin Garg2014-09-04-11/+11
| | | | | | | Couple of issues in commit 21a2eb5f. The RAM size is wrong and max number of DCD is 220. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00323255 Fixed QSPI randomly access timeout issueAllen Xu2014-08-29-16/+22
| | | | | | | | | | | | | | | | The QSPI clock rate was set without disabling the clock gate, the randomly glitch may mess up the clock and there will be no clock output, when kernel boot up the QSPI access will fail. To debug this issueon i.MX6SX SDB, changed the u-boot bootscript to 'sf probe; reset' to keep rebooting, the issue can be reproduced in 20 mins, set clock out register in CCM and measured TP86, found there is no clock ouput. To fix this bug, disable clock gate before changing clock rate. NOTICE: QSPI2 and GPMI_BCH_INPUT_GPMI_IO share the same clock gate, need to disable both of them. Signed-off-by: Allen Xu <b45815@freescale.com>
* ENGR00329631: imx6: fix kernel suspend reboot if keep watchdog aliveRobin Gong2014-09-02-0/+5
| | | | | | | WDZST bit is write-once only bit. So we need take care the setting in kernel ,otherwise, kernel setting will never be enabled. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00328278: Add support for i.MX6DQ/DL arm2 LPDDR2 boardsNitin Garg2014-08-28-8/+989
| | | | | | Add support for i.MX6DQ/DL arm2 LPDDR2 boards. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00326277-2 imx6: watchdog: use WDOG_B mode for wdog reset in ldo-bypass modeRobin Gong2014-08-26-7/+28
| | | | | | In ldo-bypass mode, we need trigger WDOG_B pin to reset pmic in ldo-bypass mode. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00326277-1: imx6: ldo_bypass: fix VDDARM voltage setting violate datasheetRobin Gong2014-08-26-11/+145
| | | | | | | | | Current only set VDDARM_IN@1.175V/VDDSOC_IN@1.175V before ldo bypass switch. So untile ldo bypass switch happened, these voltage setting is set in ldo-enable mode. But in datasheet, we need 1.15V + 125mV = 1.275V for VDDARM_IN. We need to downgrade cpufreq to 400Mhz and restore after ldo bypass mode switch. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00328312 i2c: imx: Optimize the i2c device recovery solutionFugang Duan2014-08-25-2/+25
| | | | | | | | | | | | | | | From i2c spec, if device pull down the SDA line that causes i2c bus dead, host can send out 9 clock to let device release SDA. But for some special device like pfuze100, it pull down SDA line and the solution cannot take effort. The patch just add NACK and STOP signal after 8 dummy clock, and pmic can release SDA line after the recovery. Test case catch 375 times of i2c hang, and all are recovered. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00326994 iMX6: Checking PLL2 PFD0 and PFD2 for periph_clk before resetYe.Li2014-08-15-7/+16
| | | | | | | | | | | | | u-boot v2014 upstream codes have a problem in pfd reset (s_init function) that imx6 Dual is not applied for PLL2 PFD2 reset. It is originated by using dynamical cpu type checking and introducing two cpu types: MXC_CPU_MX6Q and MXC_CPU_MX6D for iMX6 Dual/Quad platform. Fixed this problem by checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source, do not reset this PFD to avoid system hang. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00326448: mx6slevk: I2C: correct scl/sda defineRobin Gong2014-08-08-2/+2
| | | | | | | Correct the wrong setting, otherwise, i2c recovery code will use the wrong scl pin to recove, and will never recovery successfully. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00325634 iMX6DQ{DL}:SABRESD Fixed bmode booting failure for eMMCYe.Li2014-08-07-1/+1
| | | | | | | The BOOTCFG value used by bmode for SABRESD eMMC are actually for SD card. Fixed the value to correct one. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00326213 iMX6SX:19x19ARM2: Update LPDDR2 settingsYe.Li2014-08-07-34/+37
| | | | | | | | | | HWApps team updates iMX6SX 19x19 validation board LPDDR2 script. This script is JEDEC compliant. http://compass.freescale.net/livelink/livelink/open/232537085 Update the LPDDR2 settings in DCD and plugin. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00325088 video: mxsfb: Disable LCDIF correctlyLiu Ying2014-08-04-5/+9
| | | | | | | | | | | | | | | | | Let's use the i.MX common miscellaneous reset API to reset the LCDIF block so that we may eliminate a random hang issue at the arch_preboot_os() stage when we disable the LCDIF. This patch also waits for a VSYNC interrupt to guarantee the reset is done at the VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?) and helps the LCDIF work normally at the kernel stage. Tested-by: Jason Liu <r64343@freescale.com> Tested-by: Sandor Yu <R01008@freescale.com> Tested-by: Ye.Li <B37916@freescale.com> Tested-by: Guo Sally <b38912@freescale.com> Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00325255 pcie:enable pcie support on imx6sx sdRichard Zhu2014-07-31-14/+190
| | | | | | | | | | | | | | Enable pcie support in uboot on imx6sx sd boards - enable_pcie_clock should be call before ssp_en is set, since that ssp_en control the phy_ref clk gate, turn on it after the source of the pcie clks are stable. - add debug info - add rx_eq of gpr12 on imx6sx - there are random link down issue on imx6sx. It's pcie ep reset issue. solution:reset ep, then retry link can fix it. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00324352 Set console value to show log info for mfgtool nand downloadAllen Xu2014-07-24-0/+1
| | | | | | set console value to show download log info for mfgtool NAND download. Signed-off-by: Allen Xu <b45815@freescale.com>
* ENGR00323465: iMX6SX ARM2: modified NAND boot rootfs mtd partition numAllen Xu2014-07-14-1/+1
| | | | | | | | Since QSPI will be disabled for NAND module(pin conflict), the mtd partition number will be count from 0, the last partition for rootfs need to be changed from 4 to 3. Signed-off-by: Allen Xu <b45815@freescale.com>
* ENGR00323143 pcie:can't be enabled in both uboot and kernelRichard Zhu2014-07-17-1/+12
| | | | | | | | | | | | | | imx6 q/dl/solo pcie would be failed to work properly in kernel, if the pcie module is iniialized/enumerated both in uboot and linux kernel. rootcause:imx6 q/dl/solo pcie don't have the reset mechanism. it is only be RESET by the POR. So, the pcie module only be initialized/enumerated once in one POR. Set to use pcie in kernel defaultly, mask the pcie config here. Remove the mask freely, if the uboot pcie functions, rather than the kernel's, are required. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00322796 iMX6SXSABRESD: Enable Micron N25Q128 flash support for RevB boardYe.Li2014-07-17-0/+1
| | | | | | | | | The iMX6SX SABRESD RevB board uses Micron N25Q128 to replace Spansion S25FL128 on RevA board. So enable the CONFIG_SPI_FLASH_STMICRO and CONFIG_SPI_FLASH_SPANSION to support both two revisions. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00322860 iMX6SX: Add function to check M4 status before bootingYe.Li2014-07-17-1/+31
| | | | | | | Add new function "arch_auxiliary_core_check_up" to check whether M4 is already up. Therefore, avoid starting M4 again when it is running. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321435-2 video: mxc gis: do not disable mxsfbLiu Ying2014-07-17-2/+0
| | | | | | | The mxc gis driver should not disable mxsfb, instead, mxsfb could be disabled in machine layer. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00321435-1 imx-common: cpu: Disable mxsfb when necessaryLiu Ying2014-07-17-0/+4
| | | | | | | | The kernel may break the display pipeline at boot stage and introduce various display artifacts, so let's disable mxsfb in uboot when necessary. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* MX6: Correct calculation of PLL_SYSAndre Renaud2014-07-15-1/+1
| | | | | | | | DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do the shift after the multiply to avoid rounding errors Signed-off-by: Andre Renaud <andre@bluewatersys.com> (cherry picked from commit 2eb268f6fd236a5ad9d51e7e47190d7994b3920f)
* mx6: soc: Update the comments of set_ldo_voltage()Fabio Estevam2014-07-15-3/+2
| | | | | | | | | | | | | | | Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces set_ldo_voltage() function that can be used to set the voltages of any of the three LDO regulators controlled by the PMU_REG_CORE register. Prior to this commit there was a single set_vddsoc() which only configured the VDDSOC regulator. Update the comments to align with the new set_ldo_voltage() implementation. Acked-by: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> (cherry picked from commit 157f45da91b306d71dbf3a51325352dc11bf16d1)
* ENGR00321146 gis: faster auto standards detectionSandor Yu2014-07-11-1/+1
| | | | | | | | | | | | | | | | | Vadc need long time to auto standards detection, the default standard is NTSC, if vadc connect to PAL camera and no enough time to detect the video mode, driver will get wrong standard. Confirmation from chip design architecture that auto detect function is not required by rear-view camera application. Setting register vdec_stddbg standard_filte bits to 0 makes the standard detection faster, the issue duplicate decrease to 1%. Signed-off-by: Sandor Yu <R01008@freescale.com> (cherry picked from commit 06735bf6724f2dad2dcbbfc188c6a17145c7126b)
* ENGR00321577 iMX6:Android: Fixed memory overrun issue in do_bootiYe.Li2014-07-09-2/+2
| | | | | | | | | When booting from NAND, the memory copy to boothdr uses the size of fastboot_boot_img_hdr structure which is actually larger than boothdr size. This causes the u-boot heap corruption and failed to allocate memory any more. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321137 mx6sx: arm2: Expand malloc pool to 32MSandor Yu2014-07-08-1/+1
| | | | | | | | | | | | GIS module need about 3M+3M+1.5M+1.5M=9M memory. When gis module enabled, malloc may failed to allocate memory for other modules, that may cause system hang. Expand malloc pool to 32M, system hang issue can not duplicate on mx6sx arm2 board. pass one night reset stress test. Signed-off-by: Sandor Yu <R01008@freescale.com>
* ENGR00321299 gis: clean csi0 input mux set bit in GPRSandor Yu2014-07-07-0/+6
| | | | | | | | When gis enable in uboot, the CSI0 input mux select setting to vadc module, clean the bit when gis disabled. Signed-off-by: Sandor Yu <R01008@freescale.com> (cherry picked from commit ae66b17b7da3be50dc81ca636b67e8e879f52e26)
* ENGR00321260-2 iMX6:Android: Append the "androidboot.serialno" to bootargsYe.Li2014-07-04-0/+24
| | | | | | | | | | | | | Android supports to two ways to pass serialno: 1. ATAG_SERIAL 2. "androidboot.serialno=" argument in boot commandline. Since we support the DTB for android, so the ATAGS can't work. We have to choose the second way. This patch only applys the bootargs in bootimg, while the bootargs saved in u-boot env variables won't have this argument appended. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321260-1 iMX6: Add support to get CPU serial numberYe.Li2014-07-04-0/+13
| | | | | | | | The android boot needs get_board_serial function to get the CPU uid as the serial number. Implement this function to read the uid from fuse for all iMX6 platforms. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321085 iMX6SX:SABRESD: Enable the eMMC boot specific commandsYe.Li2014-07-04-0/+1
| | | | | | | | | The v2014 u-boot provides some “mmc” sub-commands for setting eMMC boot parameters, such as boot bus, partition, etc. These sub-commands are controlled by "CONFIG_SUPPORT_EMMC_BOOT". Enable this configuration for iMX6SXSABRESD board. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321077 iMX6: Enable the mtest command for DDR testYe.Li2014-07-03-0/+5
| | | | | | | The mtest is no longer default in v2014. To test the DDR, enable this command for each iMX6 board. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00320609 Use FUNC2 as Volume down key in bootloader recovery mode detectionguoyin.chen2014-07-01-2/+2
| | | | | | | | Align the keymap with Android rootfs as: FUNC1 -- > Volume + FUNC2 -- > Volume - Signed-off-by: guoyin.chen <guoyin.chen@freescale.com>
* ENGR00320125 iMX6: Change to use dynamical mmcrootYe.Li2014-06-30-48/+272
| | | | | | | | | | | | | | | | | | | | | | | | | The kernel changes to fix the mmcblk index with USDHC controllers as below: mmcblk0 ---> USDHC1 mmcblk1 ---> USDHC2 mmcblk2 ---> USDHC3 mmcblk3 ---> USDHC4 So in u-boot, the "mmcroot" must be updated together. When booting from SD/MMC device, change the "mmcroot" to dynamically set according to the boot USDHC controller. It is the same mechanism as "mmcdev" used for kernel image loading. Therefore, the uboot, kernel image, dtb and rootfs are required in same SD/MMC card. To disable the mmc dynamical detection, set the "mmcautodetect" to "no", then "mmcroot" and "mmcdev" will not be overwritten. When booting from other devices which needs to load kernel, dtb and rootfs from SD/MMC card, their "mmcdev" reset vaule is CONFIG_SYS_MMC_ENV_DEV and "mmcroot" reset value is CONFIG_MMCROOT. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00320350 iMX6SLEVK: Fix build warning of PCIE Phy power downYe.Li2014-06-30-0/+2
| | | | | | | | | | | | Since the iMX6SL does not have PCIE module, should not define the function "imx_set_pcie_phy_power_down" for it. Otherwise, get the build warning below: arch/arm/cpu/armv7/mx6/soc.c:446:13: warning: 'imx_set_pcie_phy_power_down' defined but not used [-Wunused-function] static void imx_set_pcie_phy_power_down(void) Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00320057 iMX6SX:SABRESD/19x19ARM2: Update DDR3 scriptsYe.Li2014-06-28-70/+136
| | | | | | | | Update latest DDR3 scirpts for imx6sx SabreSD and 19x19 DDR3 ARM2 board as provided by board team. (http://sw-git.freescale.net/cgi-bin/gitweb.cgi?p=ddr-scripts-rel.git) Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00319772 iMX6SX:ARM2: Add EIM-NOR support for 17x17 ARM2 boardYe.Li2014-06-25-0/+79
| | | | | | | | | | | | | | The NOR flash PC28F00AG18 has 512 of 256KB erase blocks which are locked after power on reset. Change the 17x17 ARM2 configurations to match the flash parameters, and enable the CONFIG_SYS_FLASH_PROTECTION to allow write to the flash. The EIM-NOR on 17x17 ARM2 board uses MUXed mode. This has less effort on board rework. When boot from EIM-NOR, set SW8, SW7, SW5 to all off. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00319965 pcie: mask the imx6sl outRichard Zhu2014-06-25-2/+7
| | | | | | | imx6sl doesn't have the pcie module, mask the pcie related codes from imx6sl. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00319415 pcie: random link down issue after warm-rstRichard Zhu2014-06-24-0/+18
| | | | | | | | | | | | | | | | | There are about 0.02% percentage on some imx6q/dl/solo hw boards, random pcie link down when warm-reset is used. Make sure to clear the ref_ssp_en bit16 of gpr1 before warm-rst, and set ref_ssp_en after the pcie clks are stable to workaround it. rootcause: * gpr regisers wouldn't be reset by warm-rst, while the ref_ssp_en is required to be reset by pcie. (work-around in u-boot) * ref_ssp_en should be set after pcie clks are stable. (work-around in kernel) Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00319241: imx6: pfuze: set pmic mode to decrease power number in DSM modeRobin Gong2014-06-20-0/+213
| | | | | | | Currently, kernel common regulator framework can't support setting pmic mode by common DTS, so move the related code to u-boot firstly. Signed-off-by: Robin Gong <b38343@freescale.com>
generated by cgit v1.1 at 2024-11-24 17:29:34 +0000