summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* net: Filter incoming netconsole packets by IPJoe Hershberger2012-09-24-3/+9
| | | | | | | Check the incoming packets' source IP address... if ncip isn't set to a broadcast address, only listen to the client at ncip. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* net: Allow netconsole settings to change after nc_startJoe Hershberger2012-09-24-31/+65
| | | | | | | Refresh the netconsole settings from the env before each packet instead of only on netconsole init. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* net: Improve the speed of netconsoleJoe Hershberger2012-09-24-17/+98
| | | | | | | | | | | | | | | | | | | Previously u-boot would initialize the network interface for every network operation and then shut it down again. This makes sense for most operations where the network in not known to be needed soon after the operation is complete. In the case of netconsole, it will use the network for every interaction with the shell or every printf. This means that the network is being reinitialized very often. On many devices, this intialization is very slow. This patch checks for consecutive netconsole actions and leaves the ethernet hardware initialized between them. It will still behave the same old way for all other network operations and any time another network operation happens between netconsole operations. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* net: Make the netconsole buffer size configurableJoe Hershberger2012-09-24-2/+8
| | | | | | | | | Allow a board to configure a larger buffer for netconsole, but leave the default. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
* net: sh_eth: Add support R8A7740 of rmobile (arm core)Nobuhiro Iwamatsu2012-09-24-3/+13
| | | | | | | | R8A7740 of rmobile has ethernet device, and this is same IP of sh-ether. This support R8A7740 of rmobile. Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* dm: net: Fixup the armada100 FEC driverMarek Vasut2012-09-24-2/+3
| | | | | | | | | | | Apply the following questionable adjustment to silence GCC. armada100_fec.c: In function ‘armdfec_send’: armada100_fec.c:589:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
* net: emaclite: Support OF initializationMichal Simek2012-09-24-0/+30
| | | | | | | | Support new CONFIG_OF_CONTROL option where device probing is done based on device tree description. Signed-off-by: Michal Simek <monstr@monstr.eu> CC: Joe Hershberger <joe.hershberger@gmail.com>
* dm: net: Move IXP NPE to drivers/net/Marek Vasut2012-09-24-2/+2
| | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com>
* net: bugfix: NetSetTimeout assumes CONFIG_SYS_HZ=1000Tetsuyuki Kobayashi2012-09-24-1/+1
| | | | | | NetSetTimeout sets incorrect value to timeDelta when CONFIG_SYS_HZ != 1000. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
* api: net: fix length check in eth_receive()Michael Walle2012-09-24-4/+1
| | | | | | | | | | | | | | | If the requested length is too small to hold the received packet, eth_receive() will return -1 and will leave the packet in the receive buffers. Instead of returning an error in this case, we return the first portion of the received packet and remove it from the receive buffers. This fixes FreeBSD's ubldr. Without this patch it will just stop receiving packets if the NIC receives more than PKTBUFSRX too large packets. Signed-off-by: Michael Walle <michael@walle.cc> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Rafal Jaworowski <raj@semihalf.com> Cc: Piotr Kruszynski <ppk@semihalf.com>
* net: Make netconsole src and dest ports configurableJoe Hershberger2012-09-24-16/+34
| | | | | | | | | | | | | | | It is desirable to use different port numbers for sending and receiving packets with netconsole in the case where you have more than one device on the local subnet with netconsole enabled for broadcast. When they use the same port for both, any output from one will look like input to the other. This is typlically not desirable. This patch allows the input and output ports to be specified separately in the environment. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
* Prepare v2012.10-rc1Tom Rini2012-09-21-2/+2
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini2012-09-21-12/+35
|\
| * pci: fix some warnings related to assumptions aboutKumar Gala2012-09-22-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following commit introduced some warnings associated with using pci_addr_t instead of a proper 32-bit data type. commit af778c6d9e2b945ee03cbc53bb976238a3374f33 Author: Andrew Sharp <andywyse6@gmail.com> Date: Wed Aug 1 12:27:16 2012 +0000 pci: fix errant data types and corresponding access functions On some platforms pci_addr_t is defined as a 64-bit data type so its not proper to use with pci_{read,write}_config_dword. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * fdt: Add header guard to fdtdec.hSimon Glass2012-09-21-0/+3
| | | | | | | | | | | | | | This makes it easier to include this header from other headers. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
| * fdt: Tidy debugging, add to fdtdec_get_int/addr()Simon Glass2012-09-21-8/+19
| | | | | | | | | | | | | | The new debugging shows the value of integers and addresses read from the device tree and tidy up GPIO output. Signed-off-by: Simon Glass <sjg@chromium.org>
| * Add gpio_request() to asm-generic headerSimon Glass2012-09-21-0/+9
| | | | | | | | | | | | This function should also be part of the GPIO API, so add it. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2012-09-21-803/+2455
|\ \
| * \ Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD2012-09-21-349/+409
| |\ \
| | * | mx35pdk: README: Remove NAND referencesFabio Estevam2012-09-17-76/+2
| | | | | | | | | | | | | | | | | | | | | | | | Booting from NAND is currently not supported, so remove its references. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * | mx28evk: extend default environmentOtavio Salvador2012-09-17-8/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The environment has been based on mx53loco and m28evk but keeping the possibility to easy change the default console device as Freescale and mainline kernels differ on the device name. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| | * | MX6: drop binary constants from iomux headerStefano Babic2012-09-17-62/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Constants set with binary value (0b...) are not compiled from old toolchain when used by the clrsetbits_le32 macro. Replaces them with the corresponding hex value. The error reported (for example with the mx6qsabrelite board) is something like: mx6qsabrelite.c:369:1: error: invalid suffix "b101" on integer constant mx6qsabrelite.c:369:1: error: invalid suffix "b10010" on integer constant mx6qsabrelite.c:369:1: error: invalid suffix "b0000" on integer constant mx6qsabrelite.c:369:1: error: invalid suffix "b10001" on integer constant Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * | MX35: mx35pdk: add support for MMCStefano Babic2012-09-10-2/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for SD card and change the default environment due to increased u-boot size. Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * | mx6qsabrelite:Use IMX_GPIO_NR MacroAshok Kumar Reddy2012-09-10-12/+12
| | | | | | | | | | | | | | | | Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com>
| | * | MX: set a common place to share code for Freescale i.MXStefano Babic2012-09-10-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Up now only MX5 and MX6 can share code, because they have a common source directory in cpu/armv7. Other not armv7 i.MX can profit of the same shared code. Move these files into a directory accessible for all, similar to plat-mxc in linux. Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * | ima3-mx53:Rename CONFIG_PRIME => CONFIG_ETHPRME, removeAshok Kumar Reddy2012-09-10-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | unused macro CONFIG_DISCOVER_PHY Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | mx31: Define default SoC input clock frequenciesBenoît Thébaudeau2012-09-06-20/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define default SoC input clock frequencies for i.MX31 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Helmut Raiger <helmut.raiger@hale.at>
| | * | MX28: MMC: Avoid DMA DCache race conditionMarek Vasut2012-09-06-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch prevents dcache-related problem. The problem manifested itself on the SPI driver, this is just a port to the MMC driver. The scenario is the same. In case an "mmc read" is issued to a buffer which was written right before it and data cache is enabled, the cache eviction might happen during the DMA transfer into the buffer, therefore corrupting the buffer. Clear any cache lines that might contain the buffer to prevent such issue. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| | * | MX28: SPI: Fix the DMA chainingMarek Vasut2012-09-06-18/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It turns out that in order for the SPI DMA to properly support continuous transfers longer than 65280 bytes, there are some very important parts that were left out from the documentation. Firstly, the XFER_SIZE register is not written with the whole length of a transfer, but is written by each and every chained descriptor with the length of the descriptors data buffer. Next, unlike the demo code supplied by FSL, which only writes one PIO word per descriptor, this does not apply if the descriptors are chained, since the XFER_SIZE register must be written. Therefore, it is essential to use four PIO words, CTRL0, CMD0, CMD1, XFER_SIZE. CMD0 and CMD1 are written with zero, since they don't apply. The DMA programs the PIO words in an incrementing order, so four PIO words. Finally, unlike the demo code supplied by FSL, the SSP_CTRL0_IGNORE_CRC must not be set during the whole transfer, but it must be set only on the last descriptor in the chain. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| | * | MX28: SPI: Fix the DMA DCache race conditionMarek Vasut2012-09-06-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes dcache-related problem. The problem manifested when dcache was enabled and the following command issued twice: mw 0x42000000 0 0x4000 ; sf probe ; sf read 0x42000000 0x0 0x10000 ; sha1sum 0x42000000 0x10000 The SHA1 checksum was correct during the first call. Yet with every subsequent call of the above command, it differed and was wrong. It turns out this was because of a race condition. On the first time the command was called, no cacheline contained any data from the destination memory location. The DMA transfered data into the location and the cache above the location was invalidated. Then the checksum was computed, but that meant the data were loaded into data cache. On any subsequent call, the DMA again transfered data into the same destination. Yet during the transfer, some of the DCache lines were evicted and written back into the main memory. Once the DMA transfer completed, the data cache was invalidated over the memory location as usual. But the data that were to be loaded back into the data cache by subsequent SHA1 checksuming were corrupted. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| | * | Fix mx31_decode_pllBenoît Thébaudeau2012-09-06-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MFN bit-field of the PLL registers represents a signed value. See the reference manual. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
| | * | mx35 timer: Switch to 32-kHz sourceBenoît Thébaudeau2012-09-06-17/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch the mx35 timer driver to the 32-kHz clock source to avoid calling mxc_get_clock() again and again, and to be consistent with the timer drivers of other i.MX SoCs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | mx35: Define default SoC input clock frequenciesBenoît Thébaudeau2012-09-06-30/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define default SoC input clock frequencies for i.MX35 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | mx25: Define default SoC input clock frequenciesBenoît Thébaudeau2012-09-06-11/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define default SoC input clock frequencies for i.MX25 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Matthias Weisser <weisserm@arcor.de>
| | * | mx35: Fix clock dividersBenoît Thébaudeau2012-09-06-59/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The clock dividers that were used do not match at all the reference manual. They were either completely broken, or came from an early silicon revision incompatible with the current one. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
| | * | mx35: Add definitions for clock gate valuesBenoît Thébaudeau2012-09-06-0/+6
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
| | * | mx35: Fix decode_pllBenoît Thébaudeau2012-09-06-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MFN bit-field of the PLL registers represents a signed value. See the reference manual. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
| | * | efikamx: refine USB supportMatt Sealey2012-09-04-8/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because of the way USB pad settings are handled it doesn't make sense to be able to build the Efika MX board support without CONFIG_CMD_USB turned on. So, we change the build to always compile in USB support. We do not need to check for CONFIG_CMD_USB like we do with CONFIG_MXC_SPI since the USB subsystem will error out of the compile for us. Additionally, the following behaviors have changed; * Smartbook "preboot" should not set input and output to USB keyboard as there is no display support * board_eth_init is implemented such that it does not cause U-Boot to report an explicit failure ("CPU Net Initialization Failed"). Since Ethernet is implemented via USB (fixed on Smarttop, pluggable on Smartbook, and handled by "usb start") - the warning that is left ("No ethernet found") is perfectly reasonable at the point it is printed since the USB system hasn't been started and nothing has been probed yet. Signed-off-by: Matt Sealey <matt@genesi-usa.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de>
| | * | SCSPS1: Enable cachesMarek Vasut2012-09-04-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable caches, make it faster! Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Detlev Zundel <dzu@denx.de>
| | * | mx28evk: Add USB Ethernet supportFabio Estevam2012-09-04-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add USB Ethernet support. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Marek Vasut <marex@denx.de>
| | * | MX28: Fixup the ad-hoc use of DIGCTL_MICROSECONDSMarek Vasut2012-09-04-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use proper struct-based access for this register in the SPL code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | MX28: Cleanup mxsboot within make mrproperMarek Vasut2012-09-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Delete the "mxsboot" binary if make mrproper is called. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> CC: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | M28: Fix the use of gpmi-nand in mtdpartsMarek Vasut2012-09-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mtd name of the NAND in Linux is "gpmi-nand", not "gpmi-nand.0" as it would be expected, since the controller doesn't support multiple NANDs attached to it as of now. Rectify this flub by adjusting default mtdparts. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | mx28evk: Convert to mxs_adjust_memory_params()Fabio Estevam2012-09-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recent conversion from mx28_adjust_memory_params to mxs_adjust_memory_params missed to update mx28evk, which caused the board not to boot. Apply the conversion so that the board can boot again. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
| | * | MX28: mx28evk: Enable SPI DMAOtavio Salvador2012-09-04-0/+1
| | | | | | | | | | | | | | | | Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| | * | MX28: mx28evk: Align SSP clock speedOtavio Salvador2012-09-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Align the SSP clock speed with oscilator to achieve higher transfer stability. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
| * | | NAND: MXS: include common.h first so cache.h is included in correct orderTom Warren2012-09-10-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With Simon Glass's include/nand.h alignment changes, some mxs builds were generating errors. Fix is to ensure asm/cache.h is included before linux/mtd/nand.h. Moving common.h to top of include list does that. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de>
| * | | Tegra: Change Tegra20 to Tegra in common code, prep for T30Tom Warren2012-09-10-146/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate. Convert tegra20_ source file and function names to tegra_, also. Upcoming Tegra30 port will use common code/defines/names where possible. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com>
| * | | tegra20: usb: rework set_host_modeLucas Stach2012-09-10-16/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows for two things: - VBus GPIO may be used on other ports than the OTG one - VBus GPIO may be low active if specified by DT Signed-off-by: Lucas Stach <dev@lynxeye.de> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <TWarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | | ARM: tegra: fix Ventana standalone buildStephen Warren2012-09-07-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ventana always pulls in files from the Seaboard directory, so needs to mkdir $(obj)../seaboard unconditionally. This fixes: git clean -f -d -x ./MAKEALL ventana "MAKEALL -s tegra20" passes without this change, because Seaboard happens to be built before Ventana, and hence the directory has already been created. I believe the mkdir is only needed for out-of-tree builds, since the seaboard directory is part of the source tree. However, since we always build an SPL for Tegra now, which I believe is effectively an out-of-tree build, we will always need this at some time. The overhead of just uncondtionally executing the mkdir is minimal, and simplifies the Makefile, since we don't need to code up the exact minimal condition to execute the mkdir. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
generated by cgit v1.1 at 2024-11-09 07:26:46 +0000