summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
* ENGR00275821 imx6slevk: Set PMIC's standby voltage and rampup timeAnson Huang2013-09-02-0/+48
| | | | | | | | | Need to set SW1AB and SW1C's standby voltage for suspend, from 1.375V -> 0.975V; Need to increase the speed of SW1AB and SW1C ramp up time. Signed-off-by: Anson Huang <b20788@freescale.com>
* ENGR00276023-3: ARM: mx6: enable ldo bypass check on mx6 boardRobin Gong2013-09-02-0/+6
| | | | | | | Enable ldo bypass check on mx6 and get fdt->blob from 'fdt_addr' which contained the right fdt. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00276023-2: board: freescale: mx6q: add ldo bypass interface on boardsRobin Gong2013-09-02-1/+151
| | | | | | | | | | | | | | | | | | There are three types of board for ldo bypass feature: 1.The board support ldo bypass feature, because of pmic exist. Then implement the full function in the board file. such as mx6qsabresd/mx6slevk 2.The board can't support ldo bypass feature, although pmic still be here. For example: WDOG reset pin and RESET key are not connected with PWRON of pfuze on Sabreauto board, hence at worst case chip can't boot again(reboot failed while system run on 400Mhz, because ROM boot on 800Mhz and the external pmic voltage still be kept @400Mhz). On these board we only implement 1.2G check and increase VDDARM/VDDSOC automatically. Force to ldo-enable mode always. 3.There is no PMIC on the board, hence LDO bypass feature cannot be supported. In this case, ldo_mode_set() is an empty function. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00276023-1: ARM: imx: add ldo bypass and 1.2G checkRobin Gong2013-08-29-2/+56
| | | | | | | Add ldo bypass and 1.2G check in soc.c. Extend arch_preboot_os to support read ldo-bypass from fdt. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00276276 Add config file for uboot that used for mfgtool.Lu Lin2013-08-22-0/+62
| | | | | | this patch adds the config file to build uboot of mx6qsabresd for mfgtool. Signed-off-by: Lu Lin <b37454@freescale.com>
* ENGR00275348-12 imx6slevk: add the secureboot supportJason Liu2013-08-22-0/+10
| | | | | | | | | In order to support the secureboot, please turn on the CONFIG_SECURE_BOOT in include/configs/mx6slevk.h By default, the CONFIG_SECURE_BOOT is disabled Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-11 imx6slevk: add the plugin mode supportJason Liu2013-08-22-0/+217
| | | | | | | | This patch add the plugin mode support for imx6slevk board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6slevk.h Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-10 imx6/sabre{sd,auto}: clean up the image config fileJason Liu2013-08-21-14/+41
| | | | | | | | | This patch does the following housekeep: - improve the comments for the BOOT_FROM item - fix the mising EIMNOR boot condition, - fix the nand clock gating in the image config file Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-9 imx6/sabre{sd,auto}: add the secureboot supportJason Liu2013-08-21-0/+35
| | | | | | | | | In order to support the secureboot, please turn on the CONFIG_SECURE_BOOT in include/configs/mx6qsabre_common.h By default, the CONFIG_SECURE_BOOT is disabled. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-8 imx6/arm2: add the secureboot supportJason Liu2013-08-21-0/+10
| | | | | | | | | In order to support the secureboot, please turn on CONFIG_SECURE_BOOT in the include/configs/mx6qarm2.h By default, the CONFIG_SECURE_BOOT is disabled. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-7 imx6: add secureboot supportJason Liu2013-08-21-5/+426
| | | | | | This patch add the secureboot support Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-6 imx6/sabresd: add the plugin mode supportJason Liu2013-08-21-2/+527
| | | | | | | | This patch add the plugin mode support for sabresd board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6qsabre_common.h Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-5 imx6/sabreauto: add the plugin mode supportJason Liu2013-08-21-6/+527
| | | | | | | | This patch add the plugin mode support for sabreauto board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6qsabre_common.h Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-4 imx6/arm2: add the plugin mode supportJason Liu2013-08-21-3/+294
| | | | | | | | This patch add the plugin mode support for arm2 board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6qarm2.h Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-3 imx6: add the core plugin helper function supportJason Liu2013-08-21-0/+108
| | | | | | This patch add the core plugin helper function support Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-2 tools/imximage: add the plugin mode supportJason Liu2013-08-21-56/+219
| | | | | | This patch add the plugin mode support Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275348-1 imx6: turn on L2 cache supportJason Liu2013-08-21-0/+32
| | | | | | This patch is to turn on the L2 cache support Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00275413-02: imx6sl:evk: add i2c0 support for imx6sl evkFugang Duan2013-08-15-0/+9
| | | | | | Add i2c0 bus support in mx6slevk config file. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00275413-01: ARM: MSL: add i2c0 support for imx6sl evkFugang Duan2013-08-15-0/+69
| | | | | | | - Add i2c0 support for imx6sl evk platform. - Read pmic device ID and revsion ID. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00275369-04: imx6sl:evk: add fec support in config fileFugang Duan2013-08-15-0/+14
| | | | | | Add fec support in imx6sl evk config file. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00275369-03: net: fec: add imx6sl fec supportFugang Duan2013-08-15-3/+3
| | | | | | | imx6sl fec need to setup the MII gasket for RMII mode. Add the imx6sl fec support. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00275369-02: mx6sl: add fec pad config and initial code for evkFugang Duan2013-08-15-0/+80
| | | | | | Add imx6sl evk fec pad config and fec initial code. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00275369-01: mx6sl: add fec clock enable interfaceFugang Duan2013-08-15-0/+34
| | | | | | Add fec clock enable interface in clock.c file. Signed-off-by: Fugang Duan <B38611@freescale.com>
* mx6sl: Add initial support for mx6slevk boardFabio Estevam2013-08-07-0/+439
| | | | | | | | | | | | mx6slevk board is a development board from Freescale based on the mx6 solo-lite processor. For details about mx6slevk, please refer to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX6SLEVK&parentCode=i.MX6SL&fpsp=1 [Jason Liu]: Cherry-pick from upstream version, fix some conflicts. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* mx6: Add solo-lite variant supportFabio Estevam2013-08-07-3/+133
| | | | | | | | | | mx6 solo-lite is another member of the mx6 series. For more information about mx6 solo-lite, please visit: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX6SL&nodeId=018rH3ZrDRB24A Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* cmd_mem: fix cp commandMasahiro Yamada2013-07-30-1/+1
| | | | | | | | | | | | | The "cp" command has not worked since commit 0628ab8ec59834f98ede267edd21ddb8ba0bb57b, because of the following lines, which set the destination and the source to the same address. buf = map_sysmem(addr, bytes); src = map_sysmem(addr, bytes); Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* ARM: mx6: define CONFIG_ARM_ERRATA_742230Shawn Guo2013-07-29-0/+1
| | | | | | | | | | The ARM errata 742230 - "ARM errata: DMB operation may be faulty" is claimed for Cortex-A9 (r1p0..r2p2). Though i.MX6 uses a newer revision than r2p2, we are seeing a reboot failure on i.MX6 SMP build that can be fixed by applying the workaround for this errata. So for safety, let's define CONFIG_ARM_ERRATA_742230 to enable the workaround on i.MX6. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ENGR00268897 imx6q:sata_boot:fix the build warning when build sata_boot u-bootJason Liu2013-06-28-1/+0
| | | | | | | Fix the build warning: bin/bash: ../tools/envcrc No such file or directory Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00258606 increase the console I/O buffer to 1KHuang Shijie2013-06-26-5/+5
| | | | | | | Current console buffer is 256 bytes long, it is too small. increase it to 1K. Signed-off-by: Huang Shijie <b32955@freescale.com>
* ENGR00268557 imx6q:sabresd: add SATA supportJason Liu2013-06-26-11/+242
| | | | | | This patch adds the SATA support for i.mx6qsabresd board Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00268502-2 imx6q{dl}-sabreauto: set the environment for NAND bootHuang Shijie2013-06-26-0/+21
| | | | | | Set the default environment for nand boot. Signed-off-by: Huang Shijie <b32955@freescale.com>
* ENGR00268502-1 imx6q{dl}-sabreauto: enable clocks for gpmiHuang Shijie2013-06-26-2/+2
| | | | | | enable the clocks for imx6q{dl}-sabreauto boards. Signed-off-by: Huang Shijie <b32955@freescale.com>
* cfi_flash: Fix unaligned accesses to cfi_qry structureAndrew Gabbasov2013-06-24-13/+20
| | | | | | | | | | | | | | | Packed structure cfi_qry contains unaligned 16- and 32-bits members, accessing which causes problems when cfi_flash driver is compiled with -munaligned-access option: flash initialization hangs, probably due to data error. Since the structure is supposed to replicate the actual data layout in CFI Flash chips, the alignment issue can't be fixed in the structure. So, unaligned fields need using of explicit unaligned access macros. Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Reviewed-By: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Stefan Roese <sr@denx.de>
* ENGR00268402 mx6dl:sabreauto:nor-boot: fix eim-nor bootJason Liu2013-06-24-3/+13
| | | | | | | Should not gate emi_slow clock if boot from NOR flash and Set the eim-nor flash header correctly Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00268061-2 imx6/sabresd: add the dynamtic mmc dev supportJason Liu2013-06-20-0/+18
| | | | | | | | | | | | | | | This patch add the support to load/save env to the slot which was used as the boot media by dynamic detection. The slot(usdhcx) vs real mmc dev number is board dependent: on imx6q/dl sabresd board, the map is as the followings: slot(USDHCx) mmc dev number SD2(USDHC2) 0 SD3(USDHC3) 1 SD4(USDHC4) 2 Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00268061-1 env_mmc: add the dynamtic mmc dev supportJason Liu2013-06-20-8/+21
| | | | | | | This patch add the support to load/save env to the slot which was used as the boot media by dynamic detection. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00268032 config/sabre_common: change the fdt_addr to a high addressJason Liu2013-06-20-1/+1
| | | | | | | | | | | | | current the fdt_addr is just 16MB offset from the ddr base address, which will cause the dtb will be overritten by linux kernel(include .bss section) if the linux kernel is bigger than 16MB, which cause setup_machine_fdt failed and thus kernel failed to boot. This patch change the defaut fdt_addr to 128MB offset from the ddr base address, which should be enough for common user case. user can change it to other value according to their system needs. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00266276 i.mx6qarm2:should include the asm/arch/mx6-pins.hJason Liu2013-06-08-2/+3
| | | | | | We need include asm/arch/mx6-pins.h now Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00265265 I2C: add I2C support on Sabre- boardRobin Gong2013-06-03-0/+245
| | | | | | - add I2C support on Sabresd ,Sabreauto board. - add pfuze init code based on I2C transfer in Sabre* board file. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00265233 config/i.mx6: fix the abuse of CONFIG_SYS_MMC_ENV_PARTJason Liu2013-06-03-5/+6
| | | | | | | | | | | | | | | | | | | | | | CONFIG_SYS_MMC_ENV_PART: was used to tell the u-boot which emmc (boot)partition to be used for the env_mmc.Usually, the emmc card will have 2 boot partitions, boot1 and boot2. 0: means user area 1: means boot partition 1 2: means boot partition 2 The patch fix the abuse of CONFIG_SYS_MMC_ENV_PART, which detached the emmc boot partition number and the mmc partition to store the boot image such as uImage/dtb or bootscripts. If user want to use the boot partition to store the u-boot env, please change the CONFIG_SYS_MMC_ENV_PART to which boot partition you want. This patch also fixed 2 small display format issue for CONFIG_LOADADDR and CONFIG_SYS_TEXT_BASE. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264385-2 i.mx6q:sabreauto: update the DDR scriptJason Liu2013-05-27-108/+83
| | | | | | | | This patch update the DDR script to the ddr-scripts-rel.git based on the top of the following commit: 7cd1c3b Removed the duplicate script files Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264385-1 i.mx6q:sabresd: update the DDR scriptJason Liu2013-05-27-121/+93
| | | | | | | | This patch update the DDR script to the ddr-scripts-rel.git based on the top of the following commit: 7cd1c3b Removed the duplicate script files Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264076-4 i.mx6:sabre_common:change mmc dev settingJason Liu2013-05-24-5/+1
| | | | | | | - change the CONFIG_MMCROOT to SDHC3(sd3) - make the mmcdev/part independent of ENV_IS_IN_MMC Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264076-5 i.mx6:shutdown vddpu and pcie phy to save powerJason Liu2013-05-24-0/+30
| | | | | | | shutdown vddpu and pcie phy to save power Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264076-3 i.mx6:gate/ungate PFD before using itJason Liu2013-05-24-0/+38
| | | | | | | | | Per the IC design, we need to gate/ungate all the unused PFDs to make sure PFD is working correctly, otherwise, PFDs may not not output clock after reset. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264076-2 i.mx6:Add the CPU temperature supportJason Liu2013-05-24-3/+692
| | | | | | | | The patch add the CPU thermal temperature support. Use universal equation for all i.MX6 series SOCs. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00264076-1 i.mx6:reset LDOs step_timeJason Liu2013-05-24-1/+9
| | | | | | | | | | | | | ROM may modify CORE's LDO step_time settings according to the fuse setting for safe, reset them to the default value.Reset it to 0'b00. 0'b00: 64 cycles of 24M clock; 0'b01: 128 cycles of 24M clock; 0'b02: 256 cycles of 24M clock; 0'b03: 512 cycles of 24M clock; Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00263306 imx6q: put CONFIG_SYS_NAND out of the common configJason Liu2013-05-22-2/+2
| | | | | | | Since Sabresd board does not have NAND, we need put CONFIG_SYS_NAND into the Sabreauto board only. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00263305-14 i.mx6:sabreauto: Add the GPMI nand supportJason Liu2013-05-21-4/+102
| | | | | | Add the GPMI nand support Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00263305-13 mtd: mxs_nand: Add support for i.MX6Stefan Roese2013-05-21-2/+26
| | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-12-18 01:42:29 +0000