summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ENGR00153394 mx50 rd3: make SDHC1 as default boot device for androidXinyu Chen2011-07-20-48/+50
| | | | | | | Drop NAND/SPI boot support. Enable fastboot. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00152907 MX5X: update GPU default cmdline.Zhang Jiejing2011-07-14-39/+39
| | | | | | update default cmdline to align with Document. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00152755 MX6 Switch DRAM init script from plugin to DCD for emmc fastbootAnish Trivedi2011-07-06-265/+146
| | | | | | | | | | | | | | | | | ROM requires DCD table instead of plugin to initialize DRAM if emmc fastboot mode is to be used. Therefore, switched the DRAM script from plugin to DCD table. The DCD table created is based on the following RVD script: Arik_init_DDR3_528MHz_002.inc found at http://compass.freescale.net/livelink/livelink?func=ll&objId=222928845 When fastboot mode is used by ROM, the MMC_BOOT register of USDHC does not get reset when RSTA bit is set by uboot driver. Therefore, need to write 0 to it manually during driver init. This brings USDHC out of fastboot mode, allowing normal communication with emmc to proceed in uboot. Changed comments for DLL delay to be more accurate. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00139206 MX6 USDHC eMMC 4.4 supportAnish Trivedi2011-07-05-24/+75
| | | | | | | | | | | New bit definitions in USDHC. Added is_usdhc variable to fsl_esdhc_cfg to distinguish between ESDHC and USDHC. Enabled DDR mode support in USDHC. Created a config to customize target delay for DDR mode. Modified USDHC pad settings to make DDR mode work for all emmcs at 50 MHz. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00152439: MX51: PLL workaround should be implemented only for PLL1Ranjani Vaidyanathan2011-07-01-2/+15
| | | | | | Make sure the PLL workaround is done only for PLL1. Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
* ENGR00152241 MX6: enable 1G speed mode for PHY and ENETZeng Zhaoming2011-06-29-10/+41
| | | | | | | | | | | | | In precode, PHY forced to work at 100M even connect to 1G switch. In this commit, let PHY auto negotiate it working speed. Enet tx work at store-and-forward mode. BTW, AR8031 take quite a long time, about 1.6s from negotiation to link up. we have to wait and then set ENET correctly. Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
* ENGR00139198: iMX61 uBoot add ENET supportZeng Zhaoming2011-06-27-69/+139
| | | | | | | | | | | | | | | | Add ENET and AR8031 PHY support to uboot. To make it works on sabreauto, need do following changes: 1. rework phy to output 125M clock from CLK_25M signal, and the 125M clock input to SoC as reference clock to generate RGMII_TXC clock. 2. Enable TXC delay in PHY debug register. 3. set ENET working in RMII mode. 4. set ENET working at 1000M or 100M/10M. 5. set ENET TX fifo to maximum to avoid underrun error. 6. force AR8031 PHY working at 100M Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
* ENGR00144424 MX6: enable uboot for ARM2(SABREAUTO) CPU boardAnson Huang2011-06-24-8/+10711
| | | | | | | | | | | | | Use 528M DDR script Disable L2 cache because rom enable L2 cache when use plug-in Fix usdhc pad settings Remove mac address hardcode Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Terry Lv <r65388@freescale.com> Signed-off-by: Anish Trivedi <anish@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00151966: MX51 - Apply SW workaround for the PLL1 unlock HW issue.Ranjani Vaidyanathan2011-06-22-10/+43
| | | | | | | | | | | | | | | | | | | | | | Apply the following SW workaround to fix the PLL unlock issue. 1.Move all the clock sources which are currently running on PLL1 from PLL1 to PLL2 2.Clear AREN bit in PLL1 (to avoid restart during MFN change) 3.Program the PLL1 to the next settings: a. MFI = 8 b. MFD = 179 c. MFN = 180 d. PLM = 1 4.Manually restart the PLL1 5.Wait to PLL1 to lock 6.Reprogram the PLL1 to the next settings: a. MFI = 60, others keep same 7.Load the MFN 8.Wait for LDREQ and delay ~4.6us 9.Switch the clocks which were previously moved from PLL1 to PLL2 back to PLL1 Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
* ENGR00151892 MX50: Workaround to prevent PLL1 from losing lockAnish Trivedi2011-06-21-24/+59
| | | | | | | | | | | | | | | PLL1 workaround to prevent it from losing lock: (1) Disable AREN bit to avoid PLL1 restart during MFN change (2) set PLL1 to ~864Mhz with MFI = 8, MFN = 180, MFD = 179, PDF = 0 (3) Manual restart PLL1 (4) Wait PLL1 lock (5) Set PLL1 to 800Mhz with only change MFN to 60, others keep (6) Set LDREQ bit to load new MFN (7) Poll on LDREQ bit for MFN update to be completed (8) Delay at least 4 us to avoid PLL1 instability window (9) Switch ARM back to PLL1 Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00151187 MX53 SMD: Kernal stopped Usb driver after reseting in stop modeWayne Zou2011-06-10-1/+14
| | | | | | | After reseting in stop mode, the VUSB_2V5 voltage is disable by pmic. It needs to be enable manually in u-boot. Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00144224: MX53: Add MMU mapping for all peripheralsTerry Lv2011-06-09-36/+84
| | | | | | | Not all peripherals are mapped in MMU. Thus we add those missed mapped area. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00144389 mx53 QS Ripley: change VCC from 1.35V to 1.3V QS Ripley boardWayne Zou2011-06-01-2/+2
| | | | | | Change VCC from 1.35V to 1.3V QS Ripley board Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00144060 MX53_SMD: recovery android, update recovery command for emmc.Zhang Jiejing2011-05-26-1/+1
| | | | | | Change the recovery boot for MX53_SMD to emmc 's device 1. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00143837 mx50 rd3: support android boot from RD3 NAND deviceXinyu Chen2011-05-23-12/+7
| | | | | | | | | Enable NAND gpio, recovery mode detect after boot from spi nor. Change default env for loading kernel and uramdisk from NAND, disabling elcdif lcd driver to support EPDC eink panel as default. Enable recovery mode support and NAND/UBI/UBIFS command. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00143704: U_BOOT: Nand oobsize is wrong in some nand chipsTerry Lv2011-05-20-7/+11
| | | | | | Nand oobsize is wrong in some nand chips. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00143298: Reinit uart after using clk commandTerry Lv2011-05-20-0/+6
| | | | | | | For clk command always make console output mess characters, here we reinitilize it after clock is changed. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00143302 Add mc34708 pmic support on loco/Ripley boardZou Weihua -wayne zou2011-05-20-10/+47
| | | | | | Add mc34708 pmic support on loco/Ripley board Signed-off-by: Zou Weihua -wayne zou <b36644@freescale.com>
* ENGR00143570 mx53: change the default environment settingLily Zhang2011-05-19-10/+14
| | | | | | | Change the default environment setting as sd boot for mx53 loco, mx53 smd and mx53 ard boards. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00143613 uboot: update the android ramdisk load addressXinyu Chen2011-05-18-3/+3
| | | | | | | update the ramdisk load address due to android kernel size enlarge. the ramdisk memory load address is 5MB offset to kernel. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00143469 mx53 smd: pull down GPIO_9 to reset the boardLily Zhang2011-05-16-0/+15
| | | | | | | | | In mx53 smd, to type "reset" command in u-boot console can not reset the system. It hangs in ROM with unknown reason. This patch adds one workaround to configure GPIO_9 (WDT_OUTPUT_B) as GPIO and pull down it to reset DA9053 PMIC. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00143461 mx51 evk: increase VDDGP as 1.1v for 800MHZLily Zhang2011-05-16-0/+5
| | | | | | | | The default VDDGP output voltage is 1.05V in mx51 evk board According to mx51 datasheet (Rev 0.4), the VDDGP for 800MHZ should be 1.1v for 800MHZ Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00143457: Don't let ROM copy .bss sectionJason Liu2011-05-16-5/+9
| | | | | | | | | | | Don't need let ROM copy the .bss section since it will all be zeroed by u-boot at start up, thus it can speed up the boot up time. Need add CONFIG_FLASH_HEADER_OFFSET to the size since ROM will copy from the beginning of the MMC card. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00143442 uboot: support android spi boot and mfg on mx50 rd3 boardXinyu Chen2011-05-16-4/+443
| | | | | | | | | | | | Add mx50_rd3_android default config file Add basic support for UBI partition mount and UBIFS file read for recovery Add gpmi nand enable in MFG kernel commandline by uboot configure, which enable MFG tool to flash system images on NAND. The total NAND boot and NAND recovery has been disabled. They will be enabled later. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00143428 mx53 ard RevB: use internal clock for sataLily Zhang2011-05-14-0/+19
| | | | | | Switch to use SATA internal clock in mx53 ARD RevB board. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00142995 MX50: Enable uSDHC instead of eSDHC for SDR modeAnish Trivedi2011-05-10-13/+103
| | | | | | | | | | | | | | | | | | On SD3 on MX50, there is an option to choose eSDHC or uSDHC controller. By default eSDHC is selected. However, eSDHC shows some borderline timing in SDR mode at 50 MHz, whereas uSDHC shows borderline timing in DDR mode at 50 MHz. Therefore, add a compile time option to uboot for MX50 to select uSDHC in SDR mode or eSDHC in DDR mode on SD3 port. By default the compile time option, CONFIG_MX50_ENABLE_USDHC_SDR, is commented out in the include/configs/mx50_<board>.h file to select eSDHC with DDR mode enabled. Uncomment the define to select uSDHC with only SDR mode enabled. Also increased max frequency supported by ESDHC to 52 MHz instead of 50 MHz. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00143178 mx53 ARD DDR3 board: add MFG tool supportLily Zhang2011-05-10-0/+231
| | | | | | Add MFG tool support for MX53 ARD DDR3 board. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00142740 mx50 rdp: mfg support GPMI nand by command lineXinyu Chen2011-04-29-2/+2
| | | | | | | | As android make UBIFS as default file system on MX508 RDP, we must enable MFG tool to support UBIFS image update. So enable GPMI nand in default commandline to detect nand devices. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00142497 Android: MX53_SMD: check eMMC and SD recovery file.Zhang Jiejing2011-04-22-38/+42
| | | | | | | | | | Check eMMC and SD cards recovery file, if it exist, enter recovery mode. original code only check SD card, since we already change main storage to eMMC, so we check it both, since most of customer still test it under SD card, check them to avoid support effert. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00142322: mx53-smd: spi nor: can't erase 0x200000 sizeTerry Lv2011-04-20-14/+14
| | | | | | | | | | | | | Spi nor can't erase 0x200000 size. There are two issues in this CR. 1. Spi nor can't erase 0x200000 size. 2. Whole chip erase don't work. The solution will be: 1. Delay more time for WIP check. 2. Use normal erase for whole chip erase. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141885: mx50 and mx53 reboot fail when booting from spi norTerry Lv2011-04-20-2/+15
| | | | | | | mx50 reboot fail when booting from spi nor. Reconfigure eCSPI SS signal as GPIO before reset. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00142259 set UART2_RXD (GP6_11) to highRobby Cai2011-04-18-0/+10
| | | | | | | Isolate EIM signals and boot configuration signals. Without this setting, the chip's temperature will be high. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00142247 MX50: Add PD+3 routine for all DDR typesRobby Cai2011-04-16-18/+34
| | | | | | | | | | | PD+3 routine help test pass for ddr with higher freq. Tested on ARM2 board (mDDR, DDR2) RDP board (LPDDR2 from both vendors) RD3 board (LPDDR2) Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00142246 MX50 Update DDR2 script to use more optimized settingsRobby Cai2011-04-16-123/+64
| | | | | | | | | | | | | | | New DDR2 initialization script from designer includes controller changes as well as very important PHY changes that increase internal sampling window to detect DQS edge. This increase compensates for possible jitter. The script, Codex_DDR2_266MHz.inc v3, is found at http://compass.freescale.net/livelink/ livelink?func=ll&objId=218722501&objAction=browse&viewType=1 Also corrected the DDR clock. (DDR mode changed from Sync to Async) Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00141335-3: Add CONFIG_EMMC_DDR_PORT_DETECT to mx53 and mx50config filesTerry Lv2011-04-11-12/+47
| | | | | | | | | | | | Add CONFIG_EMMC_DDR_PORT_DETECT to mx53 and mx50 config files. For fastboot, please note that the bit width of card should match the dip settings. For example, if mmcinfo shows eMMC 4.4 card is 8Bit DDR, then dip settings should be 8bit DDR. Then fastboot can work. Otherwise, fastboot will fail. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141335-2: get more accurate ipg_per clock frequencyTerry Lv2011-04-11-17/+24
| | | | | | | Add perclk_lp_apm_sel check to function __get_ipg_per_clk. This will get more accute clock frequency. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141335-1: Use bypass way to set ddr dll in mx53Terry Lv2011-04-11-1/+1
| | | | | | | | Usually dll setup for eMMC4.4 DDR is required to polling SLV_LOCK status bit. However the system hangs when polling for SLV_LOCK bit. The temporary workaround is to force slave override mode to bypass it. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141556: Fix copyright issueTerry Lv2011-04-08-78/+44
| | | | | | | | | | | We're following the following rules: 1. FSL copyright should be added for freescale added and modified files. 2. FSL copyright should go after existing copyrights. 3. For Duplicate FSL copyright, Our copyright will go after that also. 4. FSL copyright should not include personal names as part. 5. For only FSL copyright, "All rights reserved" is not mattered. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141410 MX50 RD3: Set GPIO4_16 to Enable DCDC_3V15Robby Cai2011-03-31-2/+12
| | | | | | | | This is needed for FEC to work properly, since FEC3V15 is supplied by DCDC_3V15. In addition, corrected the pin name for FEC_EN. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00141363: change mx53 uart clk parent to pll2Jason Chen2011-03-31-35/+60
| | | | | | | | | | Change all mx53 platform uart clk default parent to pll2. MX53 SMD board need support LVDS and HDMI at the same time, they may use the same clock parent-pll4, so kernel need change ipu di clock parent to pll3, after that, uart clock parent need change to pll2 to avoid console mess. Signed-off-by: Jason Chen <b02280@freescale.com>
* ENGR00141157: Add m25p32 spi nor config to mx53_smd_androidTerry Lv2011-03-25-6/+18
| | | | | | Add m25p32 spi nor config to mx53_smd_android. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141129: Add m25p32 spi_nor support for mx53_smdTerry Lv2011-03-24-12/+125
| | | | | | Add m25p32 spi_nor support for mx53_smd. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141058 MX50_RDP: Android Fix typo in recoevry command linerel_imx_2.6.35_11.03.00Zhang Jiejing2011-03-23-1/+1
| | | | | | | | | A typo is in last commit, will cause android recovery not work. Add a space between two string. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00141000 MX50_RDP: add android recovery support.Zhang Jiejing2011-03-23-1/+129
| | | | | | Add android recovery related config and code. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00140537 mx53: update vddgp according to new data sheetZhou Jingyu2011-03-23-0/+33
| | | | | | mx53: update vddgp according to new data sheet Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00140982 MX53 Increase VDDGP to 1.25V for 1 GHzAnish Trivedi2011-03-22-6/+6
| | | | | | | | MX53 TO 2.0 requires 1.25V for VDDGP instead of 1.2V in order for the core to operate at 1 GHz. Signed-off-by: Anish Trivedi <anish@freescale.com> Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00140872 Add MX50 RD3 SupportRobby Cai2011-03-22-10/+595
| | | | | | | | Assembled With new PMIC chip - MC34708 (Ripley), and new SPI NOR - M25P32 as well. Add new config file for RD3. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00140873: MMC may wrongly regconize 2GB eMMC as high capacityTerry Lv2011-03-21-2/+4
| | | | | | | | | | | | MMC driver may wrongly regconize some 2GB eMMC as high capacity card. This patch is picked from community. A non-zero value of SEC_COUNT does not indicate that the card is sector addressed. According to the MMC specification, cards with a densitygreater than 2GiB are sector addressed. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00140824 Android: Enable fastboot support for mx50 rdpSammy He2011-03-21-4/+391
| | | | | | Enable fastboot support for mx50 rdp. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00140825: Add mx53 to2.1 chip id recognitionTerry2011-03-20-4/+19
| | | | | | Add mx53 to2.1 chip id recognition. Signed-off-by: Terry Lv <r65388@freescale.com>
generated by cgit v1.1 at 2024-12-26 09:15:02 +0000