summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ENGR00142322: mx53-smd: spi nor: can't erase 0x200000 sizerel_imx_2.6.35_11.04.01imx_v2009.08_11.04.01Terry Lv2011-04-21-14/+14
| | | | | | | | | | | | | Spi nor can't erase 0x200000 size. There are two issues in this CR. 1. Spi nor can't erase 0x200000 size. 2. Whole chip erase don't work. The solution will be: 1. Delay more time for WIP check. 2. Use normal erase for whole chip erase. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141885: mx50 and mx53 reboot fail when booting from spi norTerry Lv2011-04-21-2/+15
| | | | | | | mx50 reboot fail when booting from spi nor. Reconfigure eCSPI SS signal as GPIO before reset. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00142259 set UART2_RXD (GP6_11) to highRobby Cai2011-04-18-0/+10
| | | | | | | Isolate EIM signals and boot configuration signals. Without this setting, the chip's temperature will be high. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00142247 MX50: Add PD+3 routine for all DDR typesRobby Cai2011-04-16-18/+34
| | | | | | | | | | | PD+3 routine help test pass for ddr with higher freq. Tested on ARM2 board (mDDR, DDR2) RDP board (LPDDR2 from both vendors) RD3 board (LPDDR2) Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00142246 MX50 Update DDR2 script to use more optimized settingsRobby Cai2011-04-16-123/+64
| | | | | | | | | | | | | | | New DDR2 initialization script from designer includes controller changes as well as very important PHY changes that increase internal sampling window to detect DQS edge. This increase compensates for possible jitter. The script, Codex_DDR2_266MHz.inc v3, is found at http://compass.freescale.net/livelink/ livelink?func=ll&objId=218722501&objAction=browse&viewType=1 Also corrected the DDR clock. (DDR mode changed from Sync to Async) Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00141335-3: Add CONFIG_EMMC_DDR_PORT_DETECT to mx53 and mx50config filesTerry Lv2011-04-11-12/+47
| | | | | | | | | | | | Add CONFIG_EMMC_DDR_PORT_DETECT to mx53 and mx50 config files. For fastboot, please note that the bit width of card should match the dip settings. For example, if mmcinfo shows eMMC 4.4 card is 8Bit DDR, then dip settings should be 8bit DDR. Then fastboot can work. Otherwise, fastboot will fail. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141335-2: get more accurate ipg_per clock frequencyTerry Lv2011-04-11-17/+24
| | | | | | | Add perclk_lp_apm_sel check to function __get_ipg_per_clk. This will get more accute clock frequency. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141335-1: Use bypass way to set ddr dll in mx53Terry Lv2011-04-11-1/+1
| | | | | | | | Usually dll setup for eMMC4.4 DDR is required to polling SLV_LOCK status bit. However the system hangs when polling for SLV_LOCK bit. The temporary workaround is to force slave override mode to bypass it. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141556: Fix copyright issueTerry Lv2011-04-08-78/+44
| | | | | | | | | | | We're following the following rules: 1. FSL copyright should be added for freescale added and modified files. 2. FSL copyright should go after existing copyrights. 3. For Duplicate FSL copyright, Our copyright will go after that also. 4. FSL copyright should not include personal names as part. 5. For only FSL copyright, "All rights reserved" is not mattered. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141410 MX50 RD3: Set GPIO4_16 to Enable DCDC_3V15Robby Cai2011-03-31-2/+12
| | | | | | | | This is needed for FEC to work properly, since FEC3V15 is supplied by DCDC_3V15. In addition, corrected the pin name for FEC_EN. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00141363: change mx53 uart clk parent to pll2Jason Chen2011-03-31-35/+60
| | | | | | | | | | Change all mx53 platform uart clk default parent to pll2. MX53 SMD board need support LVDS and HDMI at the same time, they may use the same clock parent-pll4, so kernel need change ipu di clock parent to pll3, after that, uart clock parent need change to pll2 to avoid console mess. Signed-off-by: Jason Chen <b02280@freescale.com>
* ENGR00141157: Add m25p32 spi nor config to mx53_smd_androidTerry Lv2011-03-25-6/+18
| | | | | | Add m25p32 spi nor config to mx53_smd_android. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141129: Add m25p32 spi_nor support for mx53_smdTerry Lv2011-03-24-12/+125
| | | | | | Add m25p32 spi_nor support for mx53_smd. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141058 MX50_RDP: Android Fix typo in recoevry command linerel_imx_2.6.35_11.03.00Zhang Jiejing2011-03-23-1/+1
| | | | | | | | | A typo is in last commit, will cause android recovery not work. Add a space between two string. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00141000 MX50_RDP: add android recovery support.Zhang Jiejing2011-03-23-1/+129
| | | | | | Add android recovery related config and code. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00140537 mx53: update vddgp according to new data sheetZhou Jingyu2011-03-23-0/+33
| | | | | | mx53: update vddgp according to new data sheet Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00140982 MX53 Increase VDDGP to 1.25V for 1 GHzAnish Trivedi2011-03-22-6/+6
| | | | | | | | MX53 TO 2.0 requires 1.25V for VDDGP instead of 1.2V in order for the core to operate at 1 GHz. Signed-off-by: Anish Trivedi <anish@freescale.com> Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00140872 Add MX50 RD3 SupportRobby Cai2011-03-22-10/+595
| | | | | | | | Assembled With new PMIC chip - MC34708 (Ripley), and new SPI NOR - M25P32 as well. Add new config file for RD3. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00140873: MMC may wrongly regconize 2GB eMMC as high capacityTerry Lv2011-03-21-2/+4
| | | | | | | | | | | | MMC driver may wrongly regconize some 2GB eMMC as high capacity card. This patch is picked from community. A non-zero value of SEC_COUNT does not indicate that the card is sector addressed. According to the MMC specification, cards with a densitygreater than 2GiB are sector addressed. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00140824 Android: Enable fastboot support for mx50 rdpSammy He2011-03-21-4/+391
| | | | | | Enable fastboot support for mx50 rdp. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00140825: Add mx53 to2.1 chip id recognitionTerry2011-03-20-4/+19
| | | | | | Add mx53 to2.1 chip id recognition. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00140486 Add SPI NOR Flash M25P32 driverRobby Cai2011-03-18-1/+565
| | | | | | | So far, it's supposed to be on MX50 RD3 and MX53 SMD Signed-off-by: Robby Cai <R63905@freescale.com> (cherry picked from commit 0e3d67cd1a2dc30af80e5119b626d997be254991)
* ENGR00140767: Improve mx5x DDR clock functionTerry2011-03-17-47/+41
| | | | | | | | | | | | | | As now mx51 DDR frequency is derived from PLL1. We need to get DDR frequency from PLL1. Mx53 don't use PLL1 for ddr clock source, so just the precision is adjusted. Mx50 don't support clk command yet. DDR config function is modified according to mx50 spec, but not tested yet. Signed-off-by: Terry <r65388@freescale.com>
* ENGR00140750 mx53smd: set the default DDR size to 512MB for android configureXinyu Chen2011-03-17-3/+2
| | | | | | | | Decrease the default DDR size to 512MB in the default android uboot configuration file. This can align with most customers' hardware design, and help us to find more issues before release. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00140692 Update for DDR3-based MX53 SABRE Auto boardsMahesh Mahadevan2011-03-16-4/+413
| | | | | | | Added a new config file, the DDR setup is similar to the MX53 Quick Start & MX53 SABRE-Tablet ref design boards. Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00140089 MX53_SMD: update command line.Zhang Jiejing2011-03-14-3/+3
| | | | | | | 1. update new style ldb per kernel update. 2. update the default boot command is from eMMC Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00138533: Fix sata write operation random failure issueTerry Lv2011-03-02-1/+3
| | | | | | | Parameter of calling to memalign is wrong. Thus need to modify it. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139747: Read fuse to distinguish between mx53 revA and revBTerry Lv2011-03-02-7/+43
| | | | | | | | | Read fuse to distinguish between mx53 revA and revB. Now SoC efuse is used for board id. Thus we now check fuse value for board rev and id. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139924 mx53 smd &loco: set bootup vdd GP to 1.2vZhou Jingyu2011-03-01-0/+6
| | | | | | set bootup vdd GP to 1.2v for mx53 smd &loco Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00139120: Correct CONFIG_CMD_MMC to CONFIG_CMD_IIM for iimTerry Lv2011-02-14-8/+8
| | | | | | Correct CONFIG_CMD_MMC to CONFIG_CMD_IIM for iim. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00138689 MX50 Update LPDDR2 script to use more optimized settingsAnish Trivedi2011-01-31-315/+42
| | | | | | | | | | | | | | | | New LPDDR2 initialization script from designer includes controller changes as well as very important PHY changes that increase internal sampling window to detect DQS edge. This increase compensates for possible jitter. The script, Codex_LPDDR2_266MHz.inc v7, is found at http://compass.freescale.net/livelink/ livelink?func=ll&objId=218722501&objAction=browse&viewType=1 Also removed ARM2 LPDDR2 init section since the settings for that board are the same as the RDP (EVK). Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00138635 MX50 Update mDDR script to use more optimized settingsAnish Trivedi2011-01-28-55/+55
| | | | | | | | | | | | | New mDDR (LPDDR1) initialization script from designer includes controller changes as well as very important PHY changes that increase internal sampling window to detect DQS edge. This increase compensates for possible jitter. The script, Codex_LPDDR1_200MHz.inc v4, is found at http://compass.freescale.net/livelink/ livelink?func=ll&objId=218722501&objAction=browse&viewType=1 Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00138549 Android fastboot: Support eMMC4.4 on imx53_smdrel_imx_2.6.35_11.01.00Sammy He2011-01-28-28/+64
| | | | | | | | Support eMMC4.4 storage on imx53_smd android fastboot, using environment to control it, the command is: > setenv fastboot_dev mmc1 Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00118558 MX51/MX53: change the boot command of android boards.Zhang Jiejing2011-01-27-10/+14
| | | | | | | The android uImage is greater than 3M, so we need to change the boot command. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00138534 Disable splashimage support defaultly for PDKLiu Ying2011-01-26-3/+0
| | | | | | | Disable splashimage support defaultly for MX51 BBG/MX53 SMD/ MX53 ARD platforms. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138422-3 Android fastboot: Pass block offset to cmd_fastbootSammy He2011-01-27-28/+28
| | | | | | Pass mmc/sata block offset from fastboot driver to cmd_fastboot, not byte. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00138422-2 Add SATA storage support for android fastbootSammy He2011-01-26-106/+138
| | | | | | Add SATA storage support for android fastboot. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00138422-1 Fix usb connection failure if do sata initSammy He2011-01-26-8/+19
| | | | | | | Increase memory alignment to fix usb connection failure issue if do sata init, and support MMU disable case in imx_udc driver. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00138468-2 Enable splashimage support for several platformsLiu Ying2011-01-25-0/+3
| | | | | | | This patch enables splashimage support for MX53 SMD/ARD and MX51 BBG pdk platforms. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138468-1 MX5 video:Disable DP/DC/DI/IDMAC before go to kernelLiu Ying2011-01-25-0/+8
| | | | | | | This patch fixes the kernel bootup random hang issue by disabling DP/DC/DI/IDMAC before we go to kernel. This is a workaround. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138390 android recovery, enlarge uImage sizeZhang Jiejing2011-01-24-2/+2
| | | | | | Kernel image is bigger than 3M, the 0x1800 will not enough. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00138359 Change uramdisk from 6M byte offset of android fastbootSammy He2011-01-22-5/+5
| | | | | | | Change uramdisk from 6M byte offset of android fastboot due to kernel image size more than 3M now. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00138240 Disable splashimage support for PDKLiu Ying2011-01-20-3/+0
| | | | | | | Disable splashimage support for mx53 smd, mx53 ard and mx51 bbg. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138191 disable the SPLASH SCREEN for androidXinyu Chen2011-01-19-2/+0
| | | | | | Disable for BBG and SMD Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00138148 MX53 TO2.0 EVK: change the default core as 1GHZLily Zhang2011-01-18-9/+18
| | | | | | | Change the default core frequency as 1GHZ for MX53 TO2.0 EVK board Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00138040-3 Protect splashimage related stuffs by configLiu Ying2011-01-17-3/+5
| | | | | | | This patch protects splashimge related stuffs by config option for mx51 bbg, mx53 ard and mx53 smd. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138040-2 MX51 BBG Android:Support splashimageLiu Ying2011-01-17-0/+19
| | | | | | This patch supports splashimage for MX51 BBG Android. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138040-1 MX53 SMD Android:Support splashimageLiu Ying2011-01-17-0/+23
| | | | | | This patch supports splashimage for MX53 SMD Android. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137552 MX53: increase VDDGP as 1.2V for 1GHZLily Zhang2011-01-15-3/+30
| | | | | | | | | The norminal voltage of VDDGP for 1GHZ is 1.2V in MX53 TO2.0 datasheet (RevD). So set the CPU frequency as 800MHZ firstly since VDDGP is 1.1V after power on. After increasing VDDGP as 1.2V, increase CPU as 1GHZ. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00137894-6 MX53 SMD:Support splashimageLiu Ying2011-01-14-1/+150
| | | | | | | | | | | | | | This patch supports to use pwm wave to control backlight. The pwm rate is 20KHz and the pwm duty is 50%. Only lvds panel is supported. Use 'lvds_num' env variable to choose to use lvds0 or lvds1. However, only lvds1 is tested as the lvds cable cannot be plugged into lvds0 connector. Note that you need to add 'splashimage' env variable to set the memory address of the bmp image. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
generated by cgit v1.1 at 2024-11-21 12:40:07 +0000