summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* lh7a40x: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD2009-06-12-1/+4
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* pxa: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD2009-06-12-1/+16
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: remove cpu_initJean-Christophe PLAGNIOL-VILLARD2009-06-12-67/+2
| | | | | | move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: unify interrupt initJean-Christophe PLAGNIOL-VILLARD2009-06-12-128/+16
| | | | | | | all arm init the IRQ stack the same way so unify it in lib_arm/interrupts.c and then call arch specific interrupt init Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: unify linker scriptJean-Christophe PLAGNIOL-VILLARD2009-06-12-3186/+134
| | | | | | | | | | | | all arm boards except a few use the same cpu linker script so move it to cpu/$(CPU) that could be overwrite in following order SOC BOARD via the corresponding config.mk Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* afeb9260: fix macb device initJean-Christophe PLAGNIOL-VILLARD2009-06-12-1/+1
| | | | | | uses PA10, PA11 for ETX2 and ETX3. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ppc4xx: Remove PCI async bootup message if PCI is not usedStefan Roese2009-06-12-1/+1
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* TQM834x: use buffered writes to accelerate writing to flashWolfgang Denk2009-06-12-4/+3
| | | | | | | Also enable display of 'E'mpty sectors in "flinfo" output. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* TQM834x: add FDT supportWolfgang Denk2009-06-12-20/+95
| | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* TQM834x: fix environment size; add redundant env.Wolfgang Denk2009-06-12-14/+12
| | | | | | | Also reserve more space for U-Boot as it will probably grow soon. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* ARM DaVinci: Reset with watchdog enabledThomas Lange2009-06-12-0/+4
| | | | | | | | | Once the Davinci watchdog has been enabled, the timeout value cannot be changed. If the timeout in use is long, it can take a long time for card to reset. By writing an invalid service key, we can trigger an immediate reset. Signed-off-by: Thomas Lange <thomas@corelatus.se>
* video: Add an option to skip video initializationWolfgang Denk2009-06-12-0/+15
| | | | | | | | | | | | | This patch adds an option to skip the video initialization on for all video drivers. This is needed for the CPCI750 which can be built as CPCI host and adapter/target board. And the adapter board can't access the video cards located on the CompactPCI bus. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Rebased against simplifying patch. Signed-off-by: Wolfgang Denk <wd@denx.de>
* drv_video_init(): simplify logicWolfgang Denk2009-06-12-40/+29
| | | | | | | | | | Simplify nesting of drv_video_init() and use a consistent way of indicating failure / success. Before, it took me some time to realize which of the returns was due to an error condition and which of them indicated success. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
* at91: regroup IP hw init in one file per socJean-Christophe PLAGNIOL-VILLARD2009-06-12-603/+338
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* dm355 evm supportDavid Brownell2009-06-12-0/+365
| | | | | | | | | | | | | | | | | | | | | Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller: http://c6000.spectrumdigital.com/evmdm355/revd/ Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling: http://focus.ti.com/docs/prod/folders/print/tms320dm355.html This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* OMAP3EVM: Set default bootfileSanjeev Premi2009-06-12-0/+2
| | | | | | | | | | | | | | | | | | | The current configuration doesn't define default bootfile; leading to this warning at execution: OMAP3_EVM # dhcp ... ... DHCP client bound to address 192.168.1.11 *** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1 Filename 'AC18BE16.img'. Load address: 0x82000000 Loading: * TFTP error: 'File not found' (1) Signed-off-by: Sanjeev Premi <premi@ti.com>
* ARM DaVinci: Minor Updates to base addressess-paulraj@ti.com2009-06-12-0/+6
| | | | | | | Patch adds base addresses for DaVinci DM365. Updated patches for DM365 will be posted soon. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ZOOM2 Add support for debug board detection.Tom Rix2009-06-12-1/+61
| | | | | | | | | | | | | | | | | | | | | | The logicpd web site is a good source for general information on this board. Please start looking here if the below links are broken. http://www.logicpd.com This is a pdf of the product http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf This is a pdf of the product quick start guide. The debug board is described here. http://support.logicpd.com/downloads/1165/ This is a wiki showing the debug board in use https://omapzoom.org/gf/project/omapzoom/wiki/?pagename=GettingStartedWithZoomII_AKA_OMAP34XII_MDP The zoom2 has an auxillary board that contains the serial, net, jtag and battery simulator. This change supports a runtime check if the debug board is connected. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* OMAP3 Port kernel omap gpio interface.Tom Rix2009-06-12-0/+304
| | | | | | | | | Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot. The orignal source is in linux/arch/arm/plat-omap/gpio.c See doc/README.omap3 for instructions on use. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* ZOOM2 Add initial support for Zoom2Tom Rix2009-06-12-2/+555
| | | | | | | | | | | | | | | | | | | | | Zoom2 is a new board from Texas Instruments and LogicPD The logicpd web site is a good source for general information on this board. Please start looking here if the below links are broken. http://www.logicpd.com This is a pdf of the product http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf This is the product description web page http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp This patch provides a zoom2 base target by copying zoom1 and by making some obvious changes. To configure, run make omap3_zoom2_config Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* ARM DaVinci:Consolidate common u-boot.ldsSandeep Paulraj2009-06-12-156/+37
| | | | | | | | | The u-boot.lds is common for all DaVinci boards. The patch removes multiple instances and moves the u-boot.lds to /cpu/arm926ejs/davinci folder. This addresses one of the comments i received while submitting patches for DM3xx Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP Consolidate common u-boot.lds to cpu layer.Tom Rix2009-06-12-257/+2
| | | | | | | The u-boot.lds file is common for all omap boards. Move a cleaned up version to the cpu layer and add makefile logic to use it. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* arm/dcc: add xscale supportJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+16
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm/dcc: use static support to allow to use it at anytimeJean-Christophe PLAGNIOL-VILLARD2009-06-12-114/+42
| | | | | | the dcc can be used at the start of the cpu Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: Update mach-typesJean-Christophe PLAGNIOL-VILLARD2009-06-12-7/+1697
| | | | | | update against linux v2.6.29 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm920/926/926: remove non needed headerJean-Christophe PLAGNIOL-VILLARD2009-06-12-41/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci dm6446evm NAND updateDavid Brownell2009-06-12-0/+7
| | | | | | | | | | | | | | | | This updates the optional (non-default!) NAND support for the DaVinci DM6446 EVM: - include MTD partitioning, defaulting to what Linux uses - use a flash-based BBT, which among other things speeds bootup This matches code that's now queued for mainline Linux, and might even merge in an upcoming 2.6.30-rc; and the MTIDS are set up so that the U-Boot $mtdparts environment variable can be passed as-is on the kernel command line as a cmdlinepart override. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: display correct clock infoDavid Brownell2009-06-12-29/+138
| | | | | | | | | | | | Move the clock-rate dumping code into the cpu/.../davinci area where it should have been, enabled by CONFIG_DISPLAY_CPUINFO, updating the format and showing the DSP clock (where relevant). Switch boards to use the cpuinfo() hook for this stuff. Remove a few now-obsolete PLL #defines. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ZOOM1 Remove more legacy NAND defines.Tom Rix2009-06-12-13/+0
| | | | | | These legacy NAND defines are no longer needed by this target. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* LED Add documentation describing the status_led and colour led API.Tom Rix2009-06-12-0/+78
| | | | | | | | This document describes the u-boot status LED API. This allows common u-boot commands to use a board's leds to provide status for activities like booting and downloading files. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* ARM Add blue colour LED to status_led.Tom Rix2009-06-12-0/+8
| | | | | | | There is exiting support for red,yellow,green but no blue. The main LED on the zoom2 is a blue LED. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* arm: timer and interrupt init reworkJean-Christophe PLAGNIOL-VILLARD2009-06-12-173/+161
| | | | | | | | | | | | | | actually the timer init use the interrupt_init as init callback which make the interrupt and timer implementation difficult to follow so now rename it as int timer_init(void) and use interrupt_init for interrupt btw also remane the corresponding file to the functionnality implemented as ixp arch implement two timer - one based on interrupt - so all the timer related code is moved to timer.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* OMAP3: Reorganize Makefile styleJean-Christophe PLAGNIOL-VILLARD2009-06-12-1/+7
| | | | | | | Reformat COBJS handling. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
* OMAP3: Remove dublicated interrupt codeJean-Christophe PLAGNIOL-VILLARD2009-06-12-128/+0
| | | | | | | | Remove duplicated interrupt code. Original, identical code can be found in lib_arm/interrupts.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
* at91rm9200: move reset code to reset.cJean-Christophe PLAGNIOL-VILLARD2009-06-12-40/+82
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ixp/interrupts: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2009-06-12-9/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: cleanup remaining CONFIG_INIT_CRITICALJean-Christophe PLAGNIOL-VILLARD2009-06-12-9/+9
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm946es: remove non used timerJean-Christophe PLAGNIOL-VILLARD2009-06-12-159/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: add basic dm355/dm350/dm335 supportDavid Brownell2009-06-12-17/+84
| | | | | | | | | | | | | Add some basic declarations for DaVinci DM355/DM350/DM335 support, keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the DM357 is very different; while the DM355 is like a DM355 without the MPEG/JPEG coprocessor). These have different peripherals than the DM6446, and some of the peripherals are at different addresses. Notably for U-Boot, there's no EMAC, and the NAND controller address is different Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: fix dm644x bugletsDavid Brownell2009-06-12-1/+3
| | | | | | | | Fix two buglets in the dm644x support: don't set two must-be-zero bits in the UART management register; and only include the I2C hooks if the I2C driver is being included. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: split out some dm644x-specific bits from pscDavid Brownell2009-06-12-75/+127
| | | | | | | | | | | | | | Split out DaVinci DM6446-specific bits from more generic bits: - Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips; DM6443 and DM6441 chips differ in available peripherals. - Move most DM644X-specific bits from psc.c to a new dm644x.c file, which is conditionally built. It provides device-specific setup. Plus minor coding style and comment updates with respect to the PSC. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: cpu-specific build uses conditional make syntaxDavid Brownell2009-06-12-3/+5
| | | | | | | | | | | Update cpu/arm926ejs/davinci/Makefile to use COBJ-y type syntax. Add the first conditional: for EMAC driver support. Not all chips have an EMAC; and boards might not use it, anyway. This doesn't touch PHY configuration; that should eventually become conditional too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: move psc support board-->cpuDavid Brownell2009-06-12-38/+10
| | | | | | | | Move DaVinci PSC support from board/* to cpu/* where it belongs. The PSC module manages clocks and resets for all DaVinci-family SoCs, and isn't at all board-specific. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* DaVinci now respects SKIP_LOWLEVEL_INITDavid Brownell2009-06-12-1/+5
| | | | | | | | Don't needlessly include lowlevel init code; that's only really needed with boot-from NOR (not boot-from-NAND). The 2nd stage loader (UBL) handles that before it loads U-Boot. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* DaVinci Ethernet cleanupDavid Brownell2009-06-12-19/+15
| | | | | | | | | | | | | | | | Chips without the EMAC controller won't need the utilities it uses to read an Ethernet address from EEPROM; so don't include them needlessly. Use is_valid_ether() to validate the address from EEPROM. All-zero addresses aren't the only invalid addresses. A fully erased EEPROM returns all-ones, also invalid... Switch those Ethernet utilities to use "%pM" for printing MAC addresses; and not say ROM when they mean EEPROM. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Ben Warren <biggerbadderben@gmail.com>
* lib_arch/board.c: Move malloc initialization before flash_init()Stefan Roese2009-06-12-28/+32
| | | | | | | | | | | | | | | | | | | This patch moves the malloc initialization before calling flash_init(). Upcoming changes to the NOR FLASH common CFI driver with optional MTD infrastructure and MTD concatenation support will call malloc(). And nothing really speaks against enabling malloc just a little earlier in the boot stage. Some architectures already enable malloc before calling flash_init() so they don't need any changes here. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Scott McNutt <smcnutt@psyent.com> Cc: Shinya Kuribayashi <shinya.kuribayashi@necel.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: John Rigby <jcrigby@gmail.com>
* ppc4xx: Add Sequoia RAM-booting targetStefan Roese2009-06-12-16/+215
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds another build target for the AMCC Sequoia PPC440EPx eval board. This RAM-booting version is targeted for boards without NOR FLASH (NAND booting) which need a possibility to initially program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000) configured to setup the SDRAM, this debugger can load this RAM- booting image to the target address in SDRAM (in this case 0x1000000) and start it there. Then U-Boot's standard NAND commands can be used to program the NAND FLASH (e.g. "nand write ..."). Here the commands to load and start this image from the BDI2000: 440EPX>reset halt 440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin 440EPX>go 0x1000000 Please note that this image automatically scans for an already initialized SDRAM TLB (detected by EPN=0). This TLB will not be cleared. This TLB doesn't need to be TLB #0, this RAM-booting version will detect it and preserve it. So booting via BDI2000 will work and booting with a complete different TLB init via U-Boot works as well. Signed-off-by: Stefan Roese <sr@denx.de>
* tools/envcrc: add --binary option to export embedded envMike Frysinger2009-06-12-4/+42
| | | | | | | The --binary option to envcrc can be used to export the embedded env as a binary blob so that it can be manipulated/examined/whatever externally. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Enable CONFIG_NET_MULTI on all remaining PPC4xx boardsBen Warren2009-06-12-1/+18
| | | | | | | All in-tree PPC4xx boards now use CONFIG_NET_MULTI Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
* 4xx: Add support for DP405 hardware variantsMatthias Fuchs2009-06-12-6/+26
| | | | | Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit v1.1 at 2024-11-16 23:38:51 +0000