summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ARM: AM33XX: Add AM33XX I2C driver supportPatil, Rachna2012-01-23-7/+13
| | | | | | | | 1. Compliant with Philips I2C specification version 2.1 2. Supports upto 100Kbps in standard mode Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
* ARM: I2C: I2C Multi byte address supportPatil, Rachna2012-01-23-173/+296
| | | | | | | | | | Existing OMAP I2C driver does not support address length greater than one. Hence this patch is to add support for 2 byte address read/write. Signed-off-by: Philip, Avinash <avinashphilip@ti.com> Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
* overo: add SPL supportAndreas Müller2012-01-16-29/+147
| | | | | | | | | | * implementation based on ti beagleboard/omap3evm * timing data and i2c workaround for revision 0 boards taken from x-loader * run-tested with overo revision 0 and 1 / boot from NAND and SDcard * run-tested with x-loader Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
* omap_rev_string: output to stdoutAndreas Müller2012-01-16-17/+11
| | | | | | | | * avoid potential buffer overflows * allow SPL-build not to output "Texas Instruments Revision detection unimplemented" Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP SPL: call timer_init in s_init to make udelay work earlierAndreas Müller2012-01-16-2/+2
| | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* drivers/i2c/omap24xx_i2c.c: move all local variables to SRAMAndreas Müller2012-01-16-4/+9
| | | | | | | | | | | | | At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately this pin is also used for revision detection. Therefore we need to send shut-up to TWL4030 to avoid reading wrong revision. In SPL this must be done before SDRAM is set up because the type of SDRAM is revision dependent. By this patch it is ensured that all variables used by omap24xx_i2c.c are located in SRAM. Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* include/configs/omap3_overo.h: several cleanupsAndreas Müller2012-01-16-35/+31
| | | | | | | | | * remove unused macros * remove unused macro values * align tabs * remove Free Software Foundation address Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* board/overo/overo.c: replace printf with one argument by putsAndreas Müller2012-01-16-7/+7
| | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* drivers/i2c/omap24xx_i2c.c: replace printf with one argument by putsAndreas Müller2012-01-16-6/+6
| | | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de>
* ARM:AM33XX: Add SPL support for AM335X EVMChandan Nath2012-01-16-122/+231
| | | | | | | | | | | This patch is added to support SPL feature on AM335X platform. In this patch, MMC1 is configured as boot device for SPL and support for other devices will be added in the next patch series. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM:AM33XX: Add mmc/sd supportChandan Nath2012-01-16-0/+205
| | | | | | | | | This patch add supports for mmc/sd driver on AM335X platform. PLL and pinmux configurations for mmc/sd are configured in this patch. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Fixing AM335X config parametersChandan Nath2012-01-16-8/+3
| | | | | | | | | This patch is added to correct some of the AM335X config parameters which were incorrect along with some cleanup like removing unused code. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Fix ddr and timer register offsetChandan Nath2012-01-16-27/+32
| | | | | | | | This patch is added to update incorrect ddr and timer register offset. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Replace CONFIG_AM335X with CONFIG_AM33XXChandan Nath2012-01-16-3/+3
| | | | | | | | | This patch is added to replace CONFIG_AM335X symbol with CONFIG_AM333XX for AM33XX platforms. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Thomas Weber <weber@corscience.de>
* cm-t35: use the new EEPROM module to read the MAC addressNikita Kiryanov2012-01-16-3/+54
| | | | | | | | | Switch to the new EEPROM module and fix the problem of MAC address being read from the wrong offset due to lack of distinction between EEPROM layouts. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: pass correct revision information to LinuxNikita Kiryanov2012-01-16-0/+28
| | | | | | | Read revision from EEPROM and pass it to Linux. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* omap3: make get_board_rev() function weakNikita Kiryanov2012-01-16-1/+2
| | | | | | | | | | Current get_board_rev() function returns a hard coded value which is obviously incorrect for the majority of boards. Allow boards to provide a correct implementation by making this function weak. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: add EEPROM module and pass Linux a serial numberNikita Kiryanov2012-01-16-1/+95
| | | | | | | | Add board specific EEPROM handling module, read the serial number from the EEPROM and pass it to Linux. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: various cleanupsNikita Kiryanov2012-01-16-6/+4
| | | | | | | | | Move #ifdef CONFIG_SMC911X out of board_eth_init() function, simplify the board_mmc_init() function, and enclose handle_mac_address() in the CONFIG_SMC911X. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: cleanup the config fileNikita Kiryanov2012-01-16-39/+39
| | | | | | | | Remove values from boolean defines, fix indentation, etc.. No functional changes. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* omap4: fix boot issue on ES2.0 PandaAneesh V2012-01-16-3/+3
| | | | | | | | | | | | | Fix boot issue on ES2.0 Panda by tuning some IO settings. The CONTROL_EFUSE_2 register has to be over-ridden in software for 4430 boards. Commit 23e9f0723e48615332119de4f4ec7a833a282628 wrongly did this for CONTROL_EFUSE_1. Reverting this and doing it for CONTROL_EFUSE_2. Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Raúl Porcel <armin76@gentoo.org>
* beagle: add eeprom expansion board info for bct brettl3Peter Meerwald2012-01-16-0/+4
| | | | | | | this is for a prototyping board vendor/product ids have been added to http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs
* ARMV7: Add support For Logic OMAP35x/DM37x modulesPeter Barada2012-01-16-0/+703
| | | | | | | | | | | | This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo reference boards. It assumes U-boot is loaded to SDRAM with the help of another small bootloader (x-load) running from SRAM. Signed-off-by: Peter Barada <peter.barada@logicpd.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* arm, davinci: Change byte order of RTC kick register valuesChristian Riesch2012-01-16-4/+4
| | | | | | | | Now the values in the defines agree with those in the manuals. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de>
* OMAP3: Remove unused define CONFIG_OMAP3_*_DDRThomas Weber2012-01-16-30/+0
| | | | | | | | | | | This patch removes the unused definitions: CONFIG_OMAP3_MICRON_DDR CONFIG_OMAP3_NUMONYX_DDR CONFIG_OMAP3_INFINEON_DDR Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
* da850evm: Remove CONFIG_SYS_xxCACHE_OFF definesChristian Riesch2012-01-16-3/+0
| | | | | | | | | | | This patch removes the defines CONFIG_SYS_ICACHE_OFF, CONFIG_SYS_DCACHE_OFF, and CONFIG_SYS_L2CACHE_OFF from the board configuration. These defines are useless since cache is anyway disabled for the entire architecture since commit cba4b1809f043bf85c806e5a4e342f62bd5ded45. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com>
* arm, davinci: Use a common configuration file for da850evm and da850_am18xxevmChristian Riesch2012-01-16-247/+1
| | | | | | | | | | | | | | | | In commit 06194b6b65f701a9d6ef2d9b4123c4afe57d8783 a separate header file was introduced for the AM1808 EVM, include/configs/da850_am18xxevm.h. Before this commit, the da850evm.h configuration file was used for both the AM1808 and the OMAP-L138 EVMs. The only substantial difference between the da850evm and the da850_am18xxevm configuration is a single bit in the hardware revision that is passed to the Linux kernel. This patch removes include/configs/da850_am18xxevm.h. Instead the include/configs/da850evm.h configuration is used for AM18xx EVMs and CONFIG_DA850_AM18X_EVM is defined in boards.cfg. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com>
* i.mx: i.mx6q: add the initial support for i.mx6q Sabre Lite boardJason Liu2012-01-16-0/+594
| | | | | | | | Add the initial support for Freescale i.MX6Q Sabre Lite board Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Jason Liu <jason.hui@linaro.org> CC: Eric Nelson <eric.nelson@boundarydevices.com>
* imx: mx6q: add aipstz init for off platform periphJason Liu2012-01-16-6/+34
| | | | | | | | | | | | Init peripheral access control register of AIPSTZ OPACRx: Buffer Writes(BW): 0 -> not bufferable, Supervisor Protect(SP): 0 -> not require supervisor privilege level for accesses. Write Protect(WP): 0 -> allows write accesses. Trusted Protect(TP): 0 -> allows unstrusted master Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de>
* mx28: fix clearing of IRQs in power initZach Sadecki2012-01-16-4/+4
| | | | | | | | | There are 2 locations in the power init code for the mx28 where IRQs are not being cleared because incorrect methods to clear those bits were being used. This was causing my board to get stuck waiting for POWER_CTRL_VDD5V_DROOP_IRQ to clear. Using the correct method to clear the IRQs fixes it. Signed-off-by: Zach Sadecki <zach@itwatchdogs.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* M28EVK: Fix build if CONFIG_CMD_NAND not selectedMarek Vasut2012-01-16-1/+3
| | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* m28evk: Remove 'all' target from MakefileFabio Estevam2012-01-16-2/+0
| | | | | | | Remove 'all' target from Makefile, as this is unused code. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* m28evk: Use GENERATED_GBL_DATA_SIZEFabio Estevam2012-01-16-1/+8
| | | | | | Use GENERATED_GBL_DATA_SIZE for calculating CONFIG_SYS_INIT_SP_OFFSET. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx28evk: Remove 'all' target from MakefileFabio Estevam2012-01-16-2/+0
| | | | | | | Remove 'all' target from Makefile, as this is unused code. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* MX28: Fix MXSBOOT segfault if no params specifiedMarek Vasut2012-01-16-0/+3
| | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* i.mx6:imx6q: allign MAC address with burned-in orderingJason Liu2012-01-16-7/+9
| | | | | | | | | | | | | | | | For the i.mx6q, the burned-in MAC address will be the following odering, fuse: 0x620[7:0] MAC_ADDR[7:0] ---> mac[5] fuse: 0x620[15:8] MAC_ADDR[15:8] ---> mac[4] fuse: 0x620[23:16] MAC_ADDR[23:16] ---> mac[3] fuse: 0x620[31:24] MAC_ADDR[31:24] ---> mac[2] fuse: 0x630[7:0] MAC_ADDR[39:32] ---> mac[1] fuse: 0x630[15:8] MAC_ADDR[47:40] ---> mac[0] This patch also fix the error caculation for the fuse bank[0] address Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de>
* mx28evk: Add initial support for MX28EVK boardFabio Estevam2012-01-16-0/+548
| | | | | | | | | | | Add initial support for Freescale MX28EVK board. Tested boot via SD card and by loading a kernel via TFTP through the FEC interface. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx28: Let dram_init be common for mx28Fabio Estevam2012-01-16-17/+24
| | | | | | | | Let dram_init function be a common function, so that other mx28 boards can reuse it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* mx28: Let imx_get_mac_from_fuse be common for mx28Fabio Estevam2012-01-16-35/+46
| | | | | | | | | Let imx_get_mac_from_fuse function be a common function, so that other mx28 boards can reuse it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* net: imx: Add multi-FEC support for imx_get_mac_from_fuseFabio Estevam2012-01-16-12/+13
| | | | | | | | | | Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter. This feature is important on mx28 SoC for example that has two FEC ports. Cc: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* i.mx6q: mx6qarm2: Enable the usboh3 clockEric Nelson2012-01-16-1/+1
| | | | | | | | | Bits 0 and 1 of CCM_CCGR7 are the usboh3 clock enable bits. Enabling this clock is necessary for the USB download. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> CC: Jason Hui <jason.hui@linaro.org> Acked-by: Jason Hui <jason.hui@linaro.org>
* mx28: remove omap specific config optionsVeli-Pekka Peltola2012-01-16-6/+0
| | | | | | | | | | | Config options for OMAP are not used with i.MX28 so remove dead code. Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* i.mx6q: arm2: Add the enet function supportJason Liu2012-01-16-2/+100
| | | | | | | | | This enable the network function on the i.mx6q armadillo2 board(arm2), thus we can use tftp to load image from network. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jason Liu <jason.hui@linaro.org> Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
* fec: add the i.mx6q enet driver supportJason Liu2012-01-16-1/+16
| | | | | | Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jason Liu <jason.hui@linaro.org> Acked-by: Stefano Babic <sbabic@denx.de>
* i.mx: i.mx6q: Add the enet clock functionJason Liu2012-01-16-0/+5
| | | | | | Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jason Liu <jason.hui@linaro.org> Acked-by: Stefano Babic <sbabic@denx.de>
* openrisc: Add MAINTAINERS entryStefan Kristiansson2012-01-13-0/+11
| | | | Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
* openrisc: Add architecture to MAKEALLStefan Kristiansson2012-01-13-0/+5
| | | | Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
* openrisc: Add openrisc-generic example boardStefan Kristiansson2012-01-13-0/+1238
| | | | Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
* openrisc: Add support for standalone programsStefan Kristiansson2012-01-13-0/+14
| | | | Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
* openrisc: Add board info printout to cmd_bdinfoStefan Kristiansson2012-01-13-0/+22
| | | | Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
generated by cgit v1.1 at 2024-12-22 22:21:46 +0000