summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ARM: OMAP5: Align memory used for testing to the power of 2SRICHARAN R2012-07-07-0/+3
| | | | | | | | | | | | get_ram_size checks the given memory range for valid ram, but expects the size of memory to be aligned to the power of 2. In case of OMAP5 evm board the memory available is 2GB - 16MB(used for TRAP section) = 2032MB. So always ensure that the size of memory used for testing is aligned to the power of 2. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP5: dmm: Create a tiler trap section.SRICHARAN R2012-07-07-3/+3
| | | | | | | | | | | | | | | | | The unmapped entries in tiler space are set with values 0xFF. So creating a DMM section of size 16MB at 0xFF000000 with ADDRSPACE set to 0x2. This way all the unmapped entry accesses to tiler will be trapped by the EMIF and a error response is sent to the L3 interconnect. L3 errors are inturn reported to MPU. Note that here the tiler trap section is overlapping with the actual ddr physical space and we lose 16MB out of the total 2GB. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4+: dmm: Take care of overlapping dmm and trap sections.SRICHARAN R2012-07-07-2/+18
| | | | | | | | | | | | | The DMM sections can be overlapping with each other, with sections 3 to 0 having the highest to lowest priority in that order. There could also be a section that is used trap the unmapped Tiler entries and this trap section could be overlapping with the actual sdram area. So take care of the above scenarios while calculating the size of the actual ram. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* arm,davinci: update for enbw_cmc boardHeiko Schocher2012-07-07-28/+364
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - change gpio pin settings: - gpio pin 6[13] (PLC reset) default value low - gpio pin 6[0] (TPM reset) default value low - 4 new GPIO pins pin i/o name - 3[9] input Board Type - 2[7] input HW-ID0 - 2[6] input HW-ID1 - 2[3] input HW-ID2 - read board type and hw id from gpio pins on the enbw_cmc board, and use board type for setting up different gpio pin settings. - do not pass "davinci_mmc.use_dma=0" to linux, as MMC now works with DMA. - update logbuf support: store post word in RTC scratch register - add support for configuring KSZ8864RMN switch through a config file on u-boot startup. For more infos see: doc/README.switch_config Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Sandeep Paulraj <s-paulraj@ti.com>
* am33xx: Do not call init_timer twiceTom Rini2012-07-07-28/+17
| | | | | | | We do not need to call init_timer both in SPL and U-Boot itself, just SPL needs to initialize the timer. Signed-off-by: Tom Rini <trini@ti.com>
* omap4/5: Use CPUDIR for .lds scriptThomas Weber2012-07-07-2/+2
| | | | Signed-off-by: Thomas Weber <thomas@tomweber.eu>
* tegra: trimslice: fix a couple typosStephen Warren2012-07-07-2/+2
| | | | | | | | | | Fix the .dts file USB unit addresses not to duplicate each-other. Fix the board name string to indicate the vendor is Compulab not NVIDIA. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* arm: Tegra: Use ODMDATA from BCT in IRAMTom Warren2012-07-07-9/+25
| | | | | | | | | | | | | | | | Walk the BIT and BCT to find the ODMDATA word in the CustomerData field and put it into Scratch20 reg for use by kernel, etc. Built all Tegra builds OK; Booted on Seaboard and saw ODMDATA in PMC scratch20 was the same as the value in my burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities will have to specify the odmdata (nvflash --odmdata n) on the command line or via a cfg file, or built in to their BCT. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
* tegra: seaboard: disable SPI, move environment to eMMCStephen Warren2012-07-07-25/+4
| | | | | | | | | | | | | | | | | | | | | | | | | The SPI hardware on Seaboard is too broken to use; it is muxed with the console UART and requires evil interactions between the SPI and UART drivers to work even partially. The current code in U-Boot is not sufficient to make this work correctly; auto boot is aborted due to corruption in the UART RX channel interrupting it. Instead, move the environment to eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage, irrespective of whether the board boots from SPI, NAND, or eMMC: if U-Boot is stored in eMMC, it will be stored well below this location. The kernel only uses the general area of the eMMC once booted, not the boot sectors. Boards that are derivatives of Seaboard don't have the muxing issue, and should/could have a separate U-Boot configuration file that does enable SPI if desired. Alternatively, the environment could be stored in NAND flash, but we currently have no driver for that controller. Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: paz00: store environment in eMMCStephen Warren2012-07-07-2/+4
| | | | | | | | | | Store the environment in eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage: U-Boot is stored well below this location, and the kernel only uses the general area of the eMMC once booted, not the boot sectors. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: trimslice: store environment in SPI flashStephen Warren2012-07-07-2/+14
| | | | | | | The chosen flash offset matches Compulab's downstream U-Boot. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* gpio: tegra2: rename tegra2_gpio.* to tegra_gpio.*Tom Warren2012-07-07-7/+8
| | | | | | | | In anticipation of Tegra3 support, continue removing/renaming Tegra2-specific files. No functional changes (yet). Updated copyrights to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
* mmc: tegra2: rename tegra2_mmc.* to tegra_mmc.*Tom Warren2012-07-07-20/+20
| | | | | | | | In anticipation of Tegra3 support, continue removing/renaming Tegra2-specific files. No functional changes (yet). Updated copyrights to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
* spi: tegra2: rename tegra2_spi.* to tegra_spi.*Tom Warren2012-07-07-10/+9
| | | | | | | | In anticipation of Tegra3 support, start removing/renaming Tegra2-specific files. No functional changes (yet). Also updated copyright to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: whistler: store environment in eMMCStephen Warren2012-07-07-2/+9
| | | | | | | | | | | | | | | Store the environment in eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage: U-Boot is stored well below this location, and the kernel only uses the general area of the eMMC once booted, not the boot sectors. Note: This assumes the user plugged the standard 8MB MoviNAND card into J29/HSMMC/POP. If they didn't, the boot sector layout may be different. However, use of that particular card is standard practice as far as I know. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: ventana: store environment in eMMCStephen Warren2012-07-07-2/+4
| | | | | | | | | | Store the environment in eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage: U-Boot is stored well below this location, and the kernel only uses the general area of the eMMC once booted, not the boot sectors. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* sf: winbond: Add support for the Winbond W25Q80BLStephen Warren2012-07-07-0/+8
| | | | | | | This chip is present on the Compulab TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* env_mmc: align buffers using ALLOC_CACHE_ALIGN_BUFFERStephen Warren2012-07-07-5/+5
| | | | | | | | | This allows MMC drivers to perform cache flusing on the bufffers without issue. Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: ventana: add own device tree, enable USBStephen Warren2012-07-07-1/+72
| | | | | | | | | | Add a device tree for Ventana; the Seaboard file no longer represents the HW present on Ventana. Enable USB on Ventana. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: remove CONFIG_USB_ETHER_SMSC95XX from boards without itStephen Warren2012-07-07-4/+0
| | | | | | | | | | | | | | The SMSC95xx series may exist either directly on a main board, or as a USB to Ethernet dongle. However, dongles containing these chips are very rare. Hence, remove this config option, except on Harmony where such a chip is actually present on the board. The asix option remains, since it's a popular chip, and I actively use a dongle containing this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* tegra: override compiler flags for low level init codeamartin@nvidia.com2012-07-07-2/+5
| | | | | | | | | | | | | | | Override -march setting for tegra to -march=armv4t for files that are necessary for low level init on tegra. The recent change to use -march=armv7-a for armv7 caused a regression on tegra because tegra starts boot on a arm7tdmi processor before transferring control to the cortex-a9. While still executing on the arm7tdmi there are calls to getenv_ulong() and memset() that cause an illegal instruction exception if compiled for armv7. Signed-off-by: Allen Martin <amartin@nvidia.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Correct PLL access in ap20.c and clock.cSimon Glass2012-07-07-6/+9
| | | | | | | | | | | | | Correct this warning seen by Albert: ap20.c:44:18: warning: array subscript is above array bounds There is a subtle bug here which currently causes no errors, but might in future if people use PCI or the 32KHz clock. So take the opportunity to correct the logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: paz00: add device tree supportStephen Warren2012-07-07-1/+78
| | | | | | | ... to enable USB host support, which enables Ethernet support. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: harmony: add device tree supportStephen Warren2012-07-07-1/+78
| | | | | | | ... to enable USB host support, which enables Ethernet support. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Compulab TrimSlice board supportStephen Warren2012-07-07-0/+270
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: add SDMMC1 on SDIO1 funcmux entryStephen Warren2012-07-07-0/+8
| | | | | | | This will be used on TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: add SDIO1 funcmux entry for UARTALucas Stach2012-07-07-0/+8
| | | | | | | | | | | | | | | This is based on top of: tegra: add alternate UART1 funcmux entry tegra: add UART1 on GPU funcmux entry v2: remove enum change Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren@nvidia.com> CC: Marek Vasut <marex@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: sync SDIO1 pingroup enum name with TRMLucas Stach2012-07-07-4/+4
| | | | | | Signed-off-by: Lucas Stach <dev@lynxeye.de> CC: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: add UART1 on GPU funcmux entryStephen Warren2012-07-07-1/+9
| | | | | | | TrimSlice uses UART1 on the GPU pingroup. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: seaboard: add support for USB networkingStephen Warren2012-07-07-0/+9
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: whistler: reduce and comment network cfg optionsStephen Warren2012-07-07-6/+4
| | | | | | | | | CONFIG_CMD_PING/NFS aren't required for Whistler to boot. Add some comments. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: flesh out bootcmdStephen Warren2012-07-07-3/+135
| | | | | | | | | | | | | | | | | | | | | | | | | This implements a useful bootcmd for Tegra. The boot order is: * If USB enabled, USB storage * Internal MMC (SD card or eMMC) * If networking is enabled, BOOTP/TFTP When booting from USB or MMC, the boot script is assumed to be in partition 1 (although this may be overridden via the rootpart variable), both ext2 and FAT filesystems are supported, the boot script may exist in either / or /boot, and the boot script may be named boot.scr.uimg or boot.scr. When booting over the network, it is assumed that boot.scr.uimg exists on the TFTP server. There is less flexibility here since those setting up network booting are expected to need less hand-holding. In all cases, it is expected that the initial file loaded is a U-Boot image containing a script that will load the kernel, load any required initrd, load any required DTB, and finally bootm the kernel. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: remove some cruft from CONFIG_EXTRA_ENV_SETTINGSStephen Warren2012-07-07-10/+0
| | | | | | | | | | | | | | | | console isn't used by anything, and the kernel should be set appropriately by whatever script is booting the kernel, not imposed by the bootloader. mem might be useful, but the current value is pretty bogus, since it includes nvmem options that make no sense for an upstream kernel, and equally should not be required for any downstream kernel. Either way, this is also best left to the kernel boot script. smpflag isn't used by anything, and again was probably intended to be a kernel command-line option better set by the kernel boot script. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Whistler board supportStephen Warren2012-07-07-0/+323
| | | | | | | | | | | | | | | | | | | Whistler is a highly configurable Tegra evaluation and development board. This change adds support for the following specific configuration: E1120 motherboard E1108 CPU board E1116 PMU board The motherboard configuration switches are set as follows: SW1=0 SW2=0 SW3=5 S1/S2/S3/S4 all on, except S3 7/8 are off. Other combinations of daugher boards may work to varying degrees, but will likely require some SW adjustment. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: add alternate UART1 funcmux entryStephen Warren2012-07-07-2/+26
| | | | | | | | (In at least some configurations) Whistler uses UART1 on pingroups UAA, UAB. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: paz00: fix typo in SD slot CD detect GPIOStephen Warren2012-07-07-3/+3
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* spi: Tegra2: Seaboard: enable SPI/UART corruption fixTom Warren2012-07-07-0/+9
| | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
* spi: Tegra2: Seaboard: fix UART corruption during SPI transactionsTom Warren2012-07-07-23/+21
| | | | | | | | | | | Simon Glass's proposal to fix this on Seaboard was NAK'd, so I removed his NS16550 references and added a small delay before SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes and saw no corruption (crc's matched) and no spurious comm chars. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
* tools/mkenvimage.c: fix basename(3) usageAndreas Bießmann2012-07-02-0/+1
| | | | | | | | | | | | | | | | | | | Use the POSIX variant of basename due to BSD systems (e.g. OS X) do not provide GNU version of basename(3). It is save to use the POSIX variant here cause we do never use argv[0] later on which may be modified by the basename(3) POSIX variant. On systems providing GNU variant the GNU variant should be used since string.h is included before libgen.h. Therefore let the _GNU_SOURCE as is. This patch fixes following warning (on OS X): ---8<--- mkenvimage.c: In function ‘main’: mkenvimage.c:105: warning: implicit declaration of function ‘basename’ mkenvimage.c:105: warning: assignment makes pointer from integer without a cast --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Keith Mok <ek9852@gmail.com>
* sh: ap_sh4a_4a: Fix wrong register initialization valueNobuhiro Iwamatsu2012-06-28-2/+2
| | | | | | | | The value of ET0_ERXD6 and GPSR1_INIT was wrong. This fixes them. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* ext2load: increase read speedu-boot@lakedaemon.net2012-06-21-2/+24
| | | | | | | | | | | | | | | | This patch dramatically drops the amount of time u-boot needs to read a file from an ext2 partition. On a typical 2 to 5 MB file (kernels and initrds) it goes from tens of seconds to a couple seconds. All we are doing here is grouping contiguous blocks into one read. Boot tested on Globalscale Technologies Dreamplug (Kirkwood ARM SoC) with three different files. sha1sums were calculated in Linux userspace, and then confirmed after ext2load. Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> Tested-by: Eric Nelson <eric.nelson@boundarydevices.com> Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
* pxe: add support for parsing local syslinux filesRob Herring2012-06-21-8/+139
| | | | | | | | Add a new command "sysboot" which parses syslinux menu files and boots using kernel and initrd specified by menu files. The operation is similar to "pxe boot" except local files on ext2 or fat filesystem are parsed. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* pxe: parse initrd file from append stringRob Herring2012-06-21-4/+14
| | | | | | | | For syslinux, the initrd can be set in the append string as "initrd=<file>", so try to find it there if we haven't already set the initrd. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* pxe: support absolute pathsRob Herring2012-06-21-11/+12
| | | | | | | | If the file path starts with a '/', then don't pre-pend the bootfile path. This fixes a problem with running 'pxe boot' multiple times where the bootfile path gets pre-pended to itself each time. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* pxe: support linux entries for labelsRob Herring2012-06-21-0/+3
| | | | | | | | Kernels can be specified using "linux" or "kernel" entry. The difference is kernel is supposed to detect the type of file, but for u-boot both are treated the same. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* pxe: add support for label menu textRob Herring2012-06-21-4/+9
| | | | | | Use a menu string if present, otherwise use the kernel string. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* pxe: support include files at top-levelRob Herring2012-06-21-0/+5
| | | | | | Include files outside of a menu were not getting included and parsed. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* menu: only timeout when menu is displayedRob Herring2012-06-21-32/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make the menu timeout apply only when prompt flag is set and after the menu is displayed. This allows auto boot to work no matter whether prompt is set or cleared. Use the default selection if the menu times out. This also fixes the timeout value given to readline_into_buffer to be seconds instead of 10th of seconds. Old behavior: if prompt display menu and wait for choice else wait for timeout if key pressed display menu and wait for choice else exit command New behavior: if prompt display menu if key pressed wait for choice else boot default entry on timeout else boot default entry Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* checkpatch: add check for whitespace before semicolon at end-of-lineEric Nelson2012-06-21-0/+6
| | | | | | | | This tests for a bad habits of mine like this: return 0 ; Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* Block: Remove MG DISK supportMarek Vasut2012-06-21-1050/+1
| | | | | | | | This driver is unused and obsolete. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: unsik Kim <donari75@gmail.com>
generated by cgit v1.1 at 2024-11-15 09:54:03 +0000