diff options
Diffstat (limited to 'include')
27 files changed, 336 insertions, 28 deletions
diff --git a/include/asm-arm/arch-davinci/gpio_defs.h b/include/asm-arm/arch-davinci/gpio_defs.h index ec43969..ff62976 100644 --- a/include/asm-arm/arch-davinci/gpio_defs.h +++ b/include/asm-arm/arch-davinci/gpio_defs.h @@ -50,4 +50,3 @@ struct davinci_gpio_bank { }; #endif - diff --git a/include/asm-blackfin/config.h b/include/asm-blackfin/config.h index 25794dd..327843d 100644 --- a/include/asm-blackfin/config.h +++ b/include/asm-blackfin/config.h @@ -18,6 +18,9 @@ # define CONFIG_BFIN_SCRATCH_REG retn #endif +/* Relocation to SDRAM works on all Blackfin boards */ +#define CONFIG_RELOC_FIXUP_WORKS + /* Make sure the structure is properly aligned */ #if ((CONFIG_SYS_GBL_DATA_ADDR & -4) != CONFIG_SYS_GBL_DATA_ADDR) # error CONFIG_SYS_GBL_DATA_ADDR: must be 4 byte aligned diff --git a/include/asm-blackfin/global_data.h b/include/asm-blackfin/global_data.h index 3194b72..b78b04c 100644 --- a/include/asm-blackfin/global_data.h +++ b/include/asm-blackfin/global_data.h @@ -44,7 +44,6 @@ typedef struct global_data { unsigned long baudrate; unsigned long have_console; /* serial_init() was called */ phys_size_t ram_size; /* RAM size */ - unsigned long reloc_off; /* Relocation Offset */ unsigned long env_addr; /* Address of Environment struct */ unsigned long env_valid; /* Checksum of Environment valid? */ #if defined(CONFIG_POST) || defined(CONFIG_LOGBUFFER) diff --git a/include/asm-ppc/config.h b/include/asm-ppc/config.h index eba7901..af0853b 100644 --- a/include/asm-ppc/config.h +++ b/include/asm-ppc/config.h @@ -47,6 +47,16 @@ #define CONFIG_MAX_CPUS 1 #endif +/* + * Provide a default boot page translation virtual address that lines up with + * Freescale's default e500 reset page. + */ +#if (defined(CONFIG_E500) && defined(CONFIG_MP)) +#ifndef CONFIG_BPTR_VIRT_ADDR +#define CONFIG_BPTR_VIRT_ADDR 0xfffff000 +#endif +#endif + /* Relocation to SDRAM works on all PPC boards */ #define CONFIG_RELOC_FIXUP_WORKS diff --git a/include/asm-ppc/fsl_pci.h b/include/asm-ppc/fsl_pci.h index 2790da7..6b0c89b 100644 --- a/include/asm-ppc/fsl_pci.h +++ b/include/asm-ppc/fsl_pci.h @@ -62,6 +62,7 @@ typedef struct pci_inbound_window { #define PIWAR_LOCAL 0x00f00000 #define PIWAR_READ_SNOOP 0x00050000 #define PIWAR_WRITE_SNOOP 0x00005000 +#define PIWAR_IWS_4K 0x0000000b u32 res2[3]; } pit_t; @@ -171,7 +172,7 @@ struct fsl_pci_info { }; int fsl_pci_init_port(struct fsl_pci_info *pci_info, - struct pci_controller *hose, int busno); + struct pci_controller *hose, int busno, int pcie_ep); #define SET_STD_PCI_INFO(x, num) \ { \ diff --git a/include/asm-ppc/immap_512x.h b/include/asm-ppc/immap_512x.h index bdc6ff2..95350fd 100644 --- a/include/asm-ppc/immap_512x.h +++ b/include/asm-ppc/immap_512x.h @@ -215,8 +215,8 @@ typedef struct clk512x { #define CLOCK_SCCR2_DIU_EN 0x80000000 #define CLOCK_SCCR2_AXE_EN 0x40000000 #define CLOCK_SCCR2_MEM_EN 0x20000000 -#define CLOCK_SCCR2_USB2_EN 0x10000000 -#define CLOCK_SCCR2_USB1_EN 0x08000000 +#define CLOCK_SCCR2_USB1_EN 0x10000000 +#define CLOCK_SCCR2_USB2_EN 0x08000000 #define CLOCK_SCCR2_I2C_EN 0x04000000 #define CLOCK_SCCR2_BDLC_EN 0x02000000 #define CLOCK_SCCR2_SDHC_EN 0x01000000 diff --git a/include/config_cmd_all.h b/include/config_cmd_all.h index c747b4b..058fdf1 100644 --- a/include/config_cmd_all.h +++ b/include/config_cmd_all.h @@ -30,6 +30,7 @@ #define CONFIG_CMD_DOC /* Disk-On-Chip Support */ #define CONFIG_CMD_DTT /* Digital Therm and Thermostat */ #define CONFIG_CMD_ECHO /* echo arguments */ +#define CONFIG_CMD_EDITENV /* editenv */ #define CONFIG_CMD_EEPROM /* EEPROM read/write support */ #define CONFIG_CMD_ELF /* ELF (VxWorks) load/boot cmd */ #define CONFIG_CMD_SAVEENV /* saveenv */ diff --git a/include/config_cmd_default.h b/include/config_cmd_default.h index a5d87a6..6e3903c 100644 --- a/include/config_cmd_default.h +++ b/include/config_cmd_default.h @@ -20,6 +20,7 @@ #define CONFIG_CMD_BOOTD /* bootd */ #define CONFIG_CMD_CONSOLE /* coninfo */ #define CONFIG_CMD_ECHO /* echo arguments */ +#define CONFIG_CMD_EDITENV /* editenv */ #define CONFIG_CMD_FPGA /* FPGA configuration Support */ #define CONFIG_CMD_IMI /* iminfo */ #define CONFIG_CMD_ITEST /* Integer (and string) test */ diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 32e747e..17ea3bb 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -70,6 +70,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_ENABLE_36BIT_PHYS 1 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_HWCONFIG #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 @@ -180,6 +181,29 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO +/* Chip select 3 - NAND */ +#define CONFIG_SYS_NAND_BASE 0xFC000000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE 1 +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) +#define CONFIG_SYS_BR3_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR3_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ /* * SDRAM on the LocalBus @@ -206,6 +230,7 @@ extern unsigned long get_clock_freq(void); /* Serial Port */ #define CONFIG_CONS_INDEX 1 +#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL @@ -258,8 +283,10 @@ extern unsigned long get_clock_freq(void); #define PLPPAR1_I2C_BIT_MASK 0x0000000F #define PLPPAR1_I2C2_VAL 0x00000000 +#define PLPPAR1_ESDHC_VAL 0x0000000A #define PLPDIR1_I2C_BIT_MASK 0x0000000F #define PLPDIR1_I2C2_VAL 0x0000000F +#define PLPDIR1_ESDHC_VAL 0x00000006 /* * General PCI @@ -450,6 +477,18 @@ extern unsigned long get_clock_freq(void); #undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_MMC 1 + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + /* * Miscellaneous configurable options */ diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 7619328..7cb4ccd 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -102,8 +102,6 @@ #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ #define CONFIG_VERY_BIG_RAM -#define MPC86xx_DDR_SDRAM_CLK_CNTL - #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index b0ae25c..a46f7c8 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -141,8 +141,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ #define CONFIG_VERY_BIG_RAM -#define MPC86xx_DDR_SDRAM_CLK_CNTL - #define CONFIG_NUM_DDR_CONTROLLERS 2 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 8e97ad0..e2930c1 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -43,6 +43,22 @@ #define CONFIG_P2020 #endif +#ifdef CONFIG_MK_NAND +#define CONFIG_NAND_U_BOOT 1 +#define CONFIG_RAMBOOT_NAND 1 +#define CONFIG_RAMBOOT_TEXT_BASE 0xf8f82000 +#endif + +#ifdef CONFIG_MK_SDCARD +#define CONFIG_RAMBOOT_SDCARD 1 +#define CONFIG_RAMBOOT_TEXT_BASE 0xf8f80000 +#endif + +#ifdef CONFIG_MK_SPIFLASH +#define CONFIG_RAMBOOT_SPIFLASH 1 +#define CONFIG_RAMBOOT_TEXT_BASE 0xf8f80000 +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ @@ -82,16 +98,34 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MEMTEST_END 0x1fffffff #define CONFIG_PANIC_HANG /* do not reset board on panic */ + /* + * Config the L2 Cache as L2 SRAM + */ +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull +#else +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#endif +#define CONFIG_SYS_L2_SIZE (512 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) + /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of */ /* CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ /* CONFIG_SYS_IMMR */ + +#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR +#else +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#endif + #define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) @@ -158,6 +192,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND) \ + || defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO @@ -177,7 +218,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ +#ifndef CONFIG_NAND_SPL #define CONFIG_SYS_NAND_BASE 0xffa00000 +#else +#define CONFIG_SYS_NAND_BASE 0xfff00000 +#endif #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} #define CONFIG_SYS_MAX_NAND_DEVICE 1 @@ -187,6 +232,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_NAND_FSL_ELBC 1 #define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) +/* NAND boot: 4K NAND loader config */ +#define CONFIG_SYS_NAND_SPL_SIZE 0x1000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) +#define CONFIG_SYS_NAND_U_BOOT_START (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_OFFS (0) +#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) + /* NAND flash config */ #define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ @@ -202,10 +256,17 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); | OR_FCM_TRLX \ | OR_FCM_EHTR) +#ifdef CONFIG_RAMBOOT_NAND +#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ +#else #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ #define CONFIG_SYS_BR1_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ #define CONFIG_SYS_OR1_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#endif #define CONFIG_SYS_VSC7385_BASE 0xffb00000 @@ -221,7 +282,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -//#define CONFIG_CONS_INDEX 2 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL @@ -371,14 +431,26 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Environment */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 -#define CONFIG_ENV_ADDR 0xfff80000 +#if defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_RAMBOOT_NAND) + #define CONFIG_ENV_IS_IN_NAND 1 + #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE + #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) + #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 +#endif #else -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) + #define CONFIG_ENV_IS_IN_FLASH 1 + #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 + #define CONFIG_ENV_ADDR 0xfff80000 + #else + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) + #endif + #define CONFIG_ENV_SIZE 0x2000 + #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h index 26b798b..7782df3 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/XPEDITE5370.h @@ -49,6 +49,13 @@ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ /* + * Multicore config + */ +#define CONFIG_MP +#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ +#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ + +/* * DDR config */ #define CONFIG_FSL_DDR2 @@ -109,6 +116,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable + * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h index 51128a3..8cd97b8 100644 --- a/include/configs/amcc-common.h +++ b/include/configs/amcc-common.h @@ -156,6 +156,8 @@ */ #define CONFIG_OF_LIBFDT #define CONFIG_OF_BOARD_SETUP +/* Update size in "reg" property of NOR FLASH device tree nodes */ +#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE /* * Booting and default environment diff --git a/include/configs/davinci_dm6467evm.h b/include/configs/davinci_dm6467evm.h index 2a4cb79..6617941 100644 --- a/include/configs/davinci_dm6467evm.h +++ b/include/configs/davinci_dm6467evm.h @@ -129,4 +129,3 @@ #endif #endif /* __CONFIG_H */ - diff --git a/include/configs/galaxy5200.h b/include/configs/galaxy5200.h index 3b67ea9..4be28b2 100644 --- a/include/configs/galaxy5200.h +++ b/include/configs/galaxy5200.h @@ -88,15 +88,21 @@ /* * Autobooting */ -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ +#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */ /* even with bootdelay=0 */ -#undef CONFIG_BOOTARGS +#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */ +#define CONFIG_RESET_TO_RETRY #define CONFIG_PREBOOT "echo;" \ "echo Welcome to U-Boot;"\ "echo" +#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \ + "bootm ff040000 ff900000 fffc0000" +#define CONFIG_BOOTARGS "console=ttyPSC0,115200" +#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0" + /* * IPB Bus clocking configuration. */ @@ -210,7 +216,7 @@ /* Chip Select configuration for NAND flash */ #define CONFIG_SYS_CS1_START 0x20000000 #define CONFIG_SYS_CS1_SIZE 0x90000 -#define CONFIG_SYS_CS1_CFG 0x0002d900 +#define CONFIG_SYS_CS1_CFG 0x00025b00 /* Chip Select configuration for Epson S1D13513 */ #define CONFIG_SYS_CS3_START 0x10000000 diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h index e5812ee..7ef6385 100644 --- a/include/configs/mcc200.h +++ b/include/configs/mcc200.h @@ -398,7 +398,7 @@ #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5) #elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5) -#elif +#else #error "Wrong QUART expander number." #endif diff --git a/include/configs/sbc35_a9g20.h b/include/configs/sbc35_a9g20.h index f4b3477..7a2dcd8 100644 --- a/include/configs/sbc35_a9g20.h +++ b/include/configs/sbc35_a9g20.h @@ -161,6 +161,7 @@ #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif #define CONFIG_BOOTCOMMAND "nboot 0x21000000 0 400000" diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index bf7cf82..7bef119 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -158,7 +158,7 @@ /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* flash Base address */ \ - (2 << BR_PS_SHIFT) | /* 32 bit port size */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ #define CONFIG_SYS_OR0_PRELIM 0xFF806FF7 /* 8 MB flash size */ @@ -304,7 +304,7 @@ #define CONFIG_SYS_I2C1_OFFSET 0x3000 #define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET -/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SPD_BUS_NUM... */ +/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ /* TSEC */ #define CONFIG_SYS_TSEC1_OFFSET 0x24000 diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 2865df5..682d241 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -121,8 +121,6 @@ #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ #define CONFIG_VERY_BIG_RAM -#define MPC86xx_DDR_SDRAM_CLK_CNTL - #define CONFIG_NUM_DDR_CONTROLLERS 2 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 89acacc..9605ce2 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -243,6 +243,11 @@ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 +/* I2C bootstrap EEPROM */ +#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52 +#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 +#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 + /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_AD7414 1 /* use AD7414 */ @@ -300,6 +305,7 @@ /* * Commands additional to the ones defined in amcc-common.h */ +#define CONFIG_CMD_CHIP_CONFIG #define CONFIG_CMD_DTT #define CONFIG_CMD_FAT #define CONFIG_CMD_NAND diff --git a/include/configs/tny_a9260.h b/include/configs/tny_a9260.h index 4ad081b..5b70a7b 100644 --- a/include/configs/tny_a9260.h +++ b/include/configs/tny_a9260.h @@ -138,6 +138,7 @@ #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif #define CONFIG_BOOTCOMMAND "nboot 0x21000000 0 400000" diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h index d0690fe..f9db73b 100644 --- a/include/configs/vme8349.h +++ b/include/configs/vme8349.h @@ -224,7 +224,7 @@ #define CONFIG_SYS_I2C1_OFFSET 0x3000 #define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C1_OFFSET -/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SPD_BUS_NUM... */ +/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ #define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */ diff --git a/include/fdt_support.h b/include/fdt_support.h index 16734c5..0a9dd0d 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -79,5 +79,7 @@ void ft_pci_setup(void *blob, bd_t *bd); void set_working_fdt_addr(void *addr); int fdt_resize(void *blob); +int fdt_fixup_nor_flash_size(void *blob, int cs, u32 size); + #endif /* ifdef CONFIG_OF_LIBFDT */ #endif /* ifndef __FDT_SUPPORT_H */ diff --git a/include/mtd/cfi_flash.h b/include/mtd/cfi_flash.h new file mode 100644 index 0000000..2aa6911 --- /dev/null +++ b/include/mtd/cfi_flash.h @@ -0,0 +1,157 @@ +/* + * (C) Copyright 2009 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef __CFI_FLASH_H__ +#define __CFI_FLASH_H__ + +#define FLASH_CMD_CFI 0x98 +#define FLASH_CMD_READ_ID 0x90 +#define FLASH_CMD_RESET 0xff +#define FLASH_CMD_BLOCK_ERASE 0x20 +#define FLASH_CMD_ERASE_CONFIRM 0xD0 +#define FLASH_CMD_WRITE 0x40 +#define FLASH_CMD_PROTECT 0x60 +#define FLASH_CMD_PROTECT_SET 0x01 +#define FLASH_CMD_PROTECT_CLEAR 0xD0 +#define FLASH_CMD_CLEAR_STATUS 0x50 +#define FLASH_CMD_READ_STATUS 0x70 +#define FLASH_CMD_WRITE_TO_BUFFER 0xE8 +#define FLASH_CMD_WRITE_BUFFER_PROG 0xE9 +#define FLASH_CMD_WRITE_BUFFER_CONFIRM 0xD0 + +#define FLASH_STATUS_DONE 0x80 +#define FLASH_STATUS_ESS 0x40 +#define FLASH_STATUS_ECLBS 0x20 +#define FLASH_STATUS_PSLBS 0x10 +#define FLASH_STATUS_VPENS 0x08 +#define FLASH_STATUS_PSS 0x04 +#define FLASH_STATUS_DPS 0x02 +#define FLASH_STATUS_R 0x01 +#define FLASH_STATUS_PROTECT 0x01 + +#define AMD_CMD_RESET 0xF0 +#define AMD_CMD_WRITE 0xA0 +#define AMD_CMD_ERASE_START 0x80 +#define AMD_CMD_ERASE_SECTOR 0x30 +#define AMD_CMD_UNLOCK_START 0xAA +#define AMD_CMD_UNLOCK_ACK 0x55 +#define AMD_CMD_WRITE_TO_BUFFER 0x25 +#define AMD_CMD_WRITE_BUFFER_CONFIRM 0x29 + +#define AMD_STATUS_TOGGLE 0x40 +#define AMD_STATUS_ERROR 0x20 + +#define ATM_CMD_UNLOCK_SECT 0x70 +#define ATM_CMD_SOFTLOCK_START 0x80 +#define ATM_CMD_LOCK_SECT 0x40 + +#define FLASH_CONTINUATION_CODE 0x7F + +#define FLASH_OFFSET_MANUFACTURER_ID 0x00 +#define FLASH_OFFSET_DEVICE_ID 0x01 +#define FLASH_OFFSET_DEVICE_ID2 0x0E +#define FLASH_OFFSET_DEVICE_ID3 0x0F +#define FLASH_OFFSET_CFI 0x55 +#define FLASH_OFFSET_CFI_ALT 0x555 +#define FLASH_OFFSET_CFI_RESP 0x10 +#define FLASH_OFFSET_PRIMARY_VENDOR 0x13 +/* extended query table primary address */ +#define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x15 +#define FLASH_OFFSET_WTOUT 0x1F +#define FLASH_OFFSET_WBTOUT 0x20 +#define FLASH_OFFSET_ETOUT 0x21 +#define FLASH_OFFSET_CETOUT 0x22 +#define FLASH_OFFSET_WMAX_TOUT 0x23 +#define FLASH_OFFSET_WBMAX_TOUT 0x24 +#define FLASH_OFFSET_EMAX_TOUT 0x25 +#define FLASH_OFFSET_CEMAX_TOUT 0x26 +#define FLASH_OFFSET_SIZE 0x27 +#define FLASH_OFFSET_INTERFACE 0x28 +#define FLASH_OFFSET_BUFFER_SIZE 0x2A +#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x2C +#define FLASH_OFFSET_ERASE_REGIONS 0x2D +#define FLASH_OFFSET_PROTECT 0x02 +#define FLASH_OFFSET_USER_PROTECTION 0x85 +#define FLASH_OFFSET_INTEL_PROTECTION 0x81 + +#define CFI_CMDSET_NONE 0 +#define CFI_CMDSET_INTEL_EXTENDED 1 +#define CFI_CMDSET_AMD_STANDARD 2 +#define CFI_CMDSET_INTEL_STANDARD 3 +#define CFI_CMDSET_AMD_EXTENDED 4 +#define CFI_CMDSET_MITSU_STANDARD 256 +#define CFI_CMDSET_MITSU_EXTENDED 257 +#define CFI_CMDSET_SST 258 +#define CFI_CMDSET_INTEL_PROG_REGIONS 512 + +#ifdef CONFIG_SYS_FLASH_CFI_AMD_RESET /* needed for STM_ID_29W320DB on UC100 */ +# undef FLASH_CMD_RESET +# define FLASH_CMD_RESET AMD_CMD_RESET /* use AMD-Reset instead */ +#endif + +#define NUM_ERASE_REGIONS 4 /* max. number of erase regions */ + +typedef union { + unsigned char c; + unsigned short w; + unsigned long l; + unsigned long long ll; +} cfiword_t; + +/* CFI standard query structure */ +struct cfi_qry { + u8 qry[3]; + u16 p_id; + u16 p_adr; + u16 a_id; + u16 a_adr; + u8 vcc_min; + u8 vcc_max; + u8 vpp_min; + u8 vpp_max; + u8 word_write_timeout_typ; + u8 buf_write_timeout_typ; + u8 block_erase_timeout_typ; + u8 chip_erase_timeout_typ; + u8 word_write_timeout_max; + u8 buf_write_timeout_max; + u8 block_erase_timeout_max; + u8 chip_erase_timeout_max; + u8 dev_size; + u16 interface_desc; + u16 max_buf_write_size; + u8 num_erase_regions; + u32 erase_region_info[NUM_ERASE_REGIONS]; +} __attribute__((packed)); + +struct cfi_pri_hdr { + u8 pri[3]; + u8 major_version; + u8 minor_version; +} __attribute__((packed)); + +void flash_write_cmd(flash_info_t * info, flash_sect_t sect, + uint offset, u32 cmd); + +#endif /* __CFI_FLASH_H__ */ diff --git a/include/ppc440.h b/include/ppc440.h index fe0db93..e54a977 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -1701,9 +1701,14 @@ #define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */ #endif /* CONFIG_440GX */ -#if defined (CONFIG_440EPX) || defined (CONFIG_440GRX) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define CPR0_ICFG_RLI_MASK 0x80000000 #define CPR0_SPCID_SPCIDV0_MASK 0x03000000 +#define CPR0_SPCID_SPCIDV0_DIV1 0x01000000 +#define CPR0_SPCID_SPCIDV0_DIV2 0x02000000 +#define CPR0_SPCID_SPCIDV0_DIV3 0x03000000 +#define CPR0_SPCID_SPCIDV0_DIV4 0x00000000 #define CPR0_PERD_PERDV0_MASK 0x07000000 #endif diff --git a/include/ppc4xx.h b/include/ppc4xx.h index 3bff00a..5024db4 100644 --- a/include/ppc4xx.h +++ b/include/ppc4xx.h @@ -221,6 +221,8 @@ static inline void set_mcsr(u32 val) asm volatile("mtspr 0x23c, %0" : "=r" (val) :); } +int ppc4xx_pci_sync_clock_config(u32 async); + #endif /* __ASSEMBLY__ */ /* for multi-cpu support */ |