summaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/ns16550.h135
-rw-r--r--include/ps2mult.h99
2 files changed, 93 insertions, 141 deletions
diff --git a/include/ns16550.h b/include/ns16550.h
index edfbc53..87624bf 100644
--- a/include/ns16550.h
+++ b/include/ns16550.h
@@ -1,6 +1,10 @@
/*
* NS16550 Serial Port
* originally from linux source (arch/ppc/boot/ns16550.h)
+ *
+ * Cleanup and unification
+ * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
+ *
* modified slightly to
* have addresses as offsets from CONFIG_SYS_ISA_BASE
* added a few more definitions
@@ -115,53 +119,100 @@ struct NS16550 {
typedef volatile struct NS16550 *NS16550_t;
-#define FCR_FIFO_EN 0x01 /* Fifo enable */
-#define FCR_RXSR 0x02 /* Receiver soft reset */
-#define FCR_TXSR 0x04 /* Transmitter soft reset */
-
-#define MCR_DTR 0x01
-#define MCR_RTS 0x02
-#define MCR_DMA_EN 0x04
-#define MCR_TX_DFR 0x08
-#define MCR_LOOP 0x10 /* Enable loopback test mode */
-
-#define LCR_WLS_MSK 0x03 /* character length select mask */
-#define LCR_WLS_5 0x00 /* 5 bit character length */
-#define LCR_WLS_6 0x01 /* 6 bit character length */
-#define LCR_WLS_7 0x02 /* 7 bit character length */
-#define LCR_WLS_8 0x03 /* 8 bit character length */
-#define LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
-#define LCR_PEN 0x08 /* Parity eneble */
-#define LCR_EPS 0x10 /* Even Parity Select */
-#define LCR_STKP 0x20 /* Stick Parity */
-#define LCR_SBRK 0x40 /* Set Break */
-#define LCR_BKSE 0x80 /* Bank select enable */
-#define LCR_DLAB 0x80 /* Divisor latch access bit */
-
-#define LSR_DR 0x01 /* Data ready */
-#define LSR_OE 0x02 /* Overrun */
-#define LSR_PE 0x04 /* Parity error */
-#define LSR_FE 0x08 /* Framing error */
-#define LSR_BI 0x10 /* Break */
-#define LSR_THRE 0x20 /* Xmit holding register empty */
-#define LSR_TEMT 0x40 /* Xmitter empty */
-#define LSR_ERR 0x80 /* Error */
-
-#define MSR_DCD 0x80 /* Data Carrier Detect */
-#define MSR_RI 0x40 /* Ring Indicator */
-#define MSR_DSR 0x20 /* Data Set Ready */
-#define MSR_CTS 0x10 /* Clear to Send */
-#define MSR_DDCD 0x08 /* Delta DCD */
-#define MSR_TERI 0x04 /* Trailing edge ring indicator */
-#define MSR_DDSR 0x02 /* Delta DSR */
-#define MSR_DCTS 0x01 /* Delta CTS */
+/*
+ * These are the definitions for the FIFO Control Register
+ */
+#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
+#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
+#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
+#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
+#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
+#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
+#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
+#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
+#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
+
+#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
+#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
+
+/*
+ * These are the definitions for the Modem Control Register
+ */
+#define UART_MCR_DTR 0x01 /* DTR */
+#define UART_MCR_RTS 0x02 /* RTS */
+#define UART_MCR_OUT1 0x04 /* Out 1 */
+#define UART_MCR_OUT2 0x08 /* Out 2 */
+#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
+
+#define UART_MCR_DMA_EN 0x04
+#define UART_MCR_TX_DFR 0x08
+
+/*
+ * These are the definitions for the Line Control Register
+ *
+ * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
+ * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
+ */
+#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
+#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
+#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
+#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
+#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
+#define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
+#define UART_LCR_PEN 0x08 /* Parity eneble */
+#define UART_LCR_EPS 0x10 /* Even Parity Select */
+#define UART_LCR_STKP 0x20 /* Stick Parity */
+#define UART_LCR_SBRK 0x40 /* Set Break */
+#define UART_LCR_BKSE 0x80 /* Bank select enable */
+#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
+
+/*
+ * These are the definitions for the Line Status Register
+ */
+#define UART_LSR_DR 0x01 /* Data ready */
+#define UART_LSR_OE 0x02 /* Overrun */
+#define UART_LSR_PE 0x04 /* Parity error */
+#define UART_LSR_FE 0x08 /* Framing error */
+#define UART_LSR_BI 0x10 /* Break */
+#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
+#define UART_LSR_TEMT 0x40 /* Xmitter empty */
+#define UART_LSR_ERR 0x80 /* Error */
+
+#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
+#define UART_MSR_RI 0x40 /* Ring Indicator */
+#define UART_MSR_DSR 0x20 /* Data Set Ready */
+#define UART_MSR_CTS 0x10 /* Clear to Send */
+#define UART_MSR_DDCD 0x08 /* Delta DCD */
+#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
+#define UART_MSR_DDSR 0x02 /* Delta DSR */
+#define UART_MSR_DCTS 0x01 /* Delta CTS */
+
+/*
+ * These are the definitions for the Interrupt Identification Register
+ */
+#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
+#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
+
+#define UART_IIR_MSI 0x00 /* Modem status interrupt */
+#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
+#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
+#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
+
+/*
+ * These are the definitions for the Interrupt Enable Register
+ */
+#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
+#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
+#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
+#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
+
#ifdef CONFIG_OMAP1510
-#define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */
+#define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */
#endif
/* useful defaults for LCR */
-#define LCR_8N1 0x03
+#define UART_LCR_8N1 0x03
void NS16550_init (NS16550_t com_port, int baud_divisor);
void NS16550_putc (NS16550_t com_port, char c);
diff --git a/include/ps2mult.h b/include/ps2mult.h
index 599cb6d..1a38733 100644
--- a/include/ps2mult.h
+++ b/include/ps2mult.h
@@ -53,103 +53,4 @@ struct serial_state {
u8 *iomem_base;
};
-#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
-#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
-#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
-
-#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
-#define UART_IER 1 /* Out: Interrupt Enable Register */
-
-#define UART_IIR 2 /* In: Interrupt ID Register */
-#define UART_FCR 2 /* Out: FIFO Control Register */
-
-#define UART_LCR 3 /* Out: Line Control Register */
-#define UART_MCR 4 /* Out: Modem Control Register */
-#define UART_LSR 5 /* In: Line Status Register */
-#define UART_MSR 6 /* In: Modem Status Register */
-#define UART_SCR 7 /* I/O: Scratch Register */
-
-/*
- * These are the definitions for the FIFO Control Register
- * (16650 only)
- */
-#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
-#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
-#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
-#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
-#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
-#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
-#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
-#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
-#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
-
-/*
- * These are the definitions for the Line Control Register
- *
- * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
- * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
- */
-#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
-#define UART_LCR_SBC 0x40 /* Set break control */
-#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
-#define UART_LCR_EPAR 0x10 /* Even parity select */
-#define UART_LCR_PARITY 0x08 /* Parity Enable */
-#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
-#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
-#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
-#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
-#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
-
-/*
- * These are the definitions for the Line Status Register
- */
-#define UART_LSR_TEMT 0x40 /* Transmitter empty */
-#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
-#define UART_LSR_BI 0x10 /* Break interrupt indicator */
-#define UART_LSR_FE 0x08 /* Frame error indicator */
-#define UART_LSR_PE 0x04 /* Parity error indicator */
-#define UART_LSR_OE 0x02 /* Overrun error indicator */
-#define UART_LSR_DR 0x01 /* Receiver data ready */
-
-/*
- * These are the definitions for the Interrupt Identification Register
- */
-#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
-#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
-
-#define UART_IIR_MSI 0x00 /* Modem status interrupt */
-#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
-#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
-#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
-
-/*
- * These are the definitions for the Interrupt Enable Register
- */
-#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
-#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
-#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
-#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
-
-/*
- * These are the definitions for the Modem Control Register
- */
-#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
-#define UART_MCR_OUT2 0x08 /* Out2 complement */
-#define UART_MCR_OUT1 0x04 /* Out1 complement */
-#define UART_MCR_RTS 0x02 /* RTS complement */
-#define UART_MCR_DTR 0x01 /* DTR complement */
-
-/*
- * These are the definitions for the Modem Status Register
- */
-#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
-#define UART_MSR_RI 0x40 /* Ring Indicator */
-#define UART_MSR_DSR 0x20 /* Data Set Ready */
-#define UART_MSR_CTS 0x10 /* Clear to Send */
-#define UART_MSR_DDCD 0x08 /* Delta DCD */
-#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
-#define UART_MSR_DDSR 0x02 /* Delta DSR */
-#define UART_MSR_DCTS 0x01 /* Delta CTS */
-#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
-
#endif /* __LINUX_PS2MULT_H */