diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/commproc.h | 22 | ||||
| -rw-r--r-- | include/configs/MHPC.h | 369 |
2 files changed, 0 insertions, 391 deletions
diff --git a/include/commproc.h b/include/commproc.h index d481707..d78ab00 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -703,28 +703,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00250000) #endif /* CONFIG_KM8XX */ - -/*** MHPC ********************************************************/ - -#if defined(CONFIG_MHPC) -/* This ENET stuff is for the MHPC with ethernet on SCC2. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */ -#endif /* CONFIG_MHPC */ - /*** NETVIA *******************************************************/ #if defined(CONFIG_NETVIA) diff --git a/include/configs/MHPC.h b/include/configs/MHPC.h deleted file mode 100644 index d45be0f..0000000 --- a/include/configs/MHPC.h +++ /dev/null @@ -1,369 +0,0 @@ -/* - * (C) Copyright 2001 - * Frank Gottschling, ELTEC Elektronik AG, fgottschling@eltec.de - * - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Configuation settings for the miniHiPerCam. - * - * ----------------------------------------------------------------- - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ -#define CONFIG_MHPC 1 /* on a miniHiPerCam */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* do special hardware init. */ -#define CONFIG_MISC_INIT_R 1 - -#define CONFIG_SYS_TEXT_BASE 0xfe000000 - -#define CONFIG_8xx_GCLK_FREQ MPC8XX_SPEED -#undef CONFIG_8xx_CONS_SMC1 -#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_ETHADDR 00:00:5b:ee:de:ad - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - -#undef CONFIG_UCODE_PATCH - -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 50000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -/* - * Software (bit-bang) I2C driver configuration - */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C04 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -#define LCD_VIDEO_ADDR (SDRAM_MAX_SIZE-SDRAM_RES_SIZE) -#define LCD_VIDEO_SIZE SDRAM_RES_SIZE /* 2MB */ -#define LCD_VIDEO_COLS 640 -#define LCD_VIDEO_ROWS 480 -#define LCD_VIDEO_FG 255 -#define LCD_VIDEO_BG 0 - -#undef CONFIG_VIDEO /* test only ! s.a devices.c and 8xx */ -#define CONFIG_CFB_CONSOLE /* framebuffer console with std input */ -#define CONFIG_VIDEO_LOGO - -#define VIDEO_KBD_INIT_FCT 0 /* no KBD dev on MHPC - use serial */ -#define VIDEO_TSTC_FCT serial_stub_tstc -#define VIDEO_GETC_FCT serial_stub_getc - -#define CONFIG_BR0_WORKAROUND 1 - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_REGINFO - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x300000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Physical memory map - */ -#define CONFIG_SYS_IMMR 0xFFF00000 /* Internal Memory Mapped Register*/ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xfe000000 - -#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */ -#undef CONFIG_SYS_MONITOR_BASE /* to run U-Boot from RAM */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=mhpc-0" -#define MTDPARTS_DEFAULT "mtdparts=mhpc-0:-(jffs2)" -*/ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map- for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN /* Offset of Environment */ -#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_SEME) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 12-18 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - leave PLL multiplication factor unchanged ! - */ -#define MPC8XX_SPEED 50000000L -#define MPC8XX_XIN 5000000L /* ref clk */ -#define MPC8XX_FACT (MPC8XX_SPEED/MPC8XX_XIN) -#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ - -#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL) /* SCCR_EBDF11 */ -#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_DFLCD001) - - -/*----------------------------------------------------------------------- - * MAMR settings for SDRAM - 16-14 - * => 0xC080200F - *----------------------------------------------------------------------- - * periodic timer for refresh - */ -#define CONFIG_SYS_MAMR_PTA 0xC0 -#define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | MAMR_G0CLA_A11 | MAMR_TLFA_MSK) - -/* - * BR0 and OR0 (FLASH) used to re-map FLASH - */ - -/* allow for max 8 MB of Flash */ -#define FLASH_BASE 0xFE000000 /* FLASH bank #0*/ -#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0*/ -#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ - -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_8_CLK) /* (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)*/ - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_GPCM | BR_V ) - -/* - * BR1 and OR1 (SDRAM) - */ -#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */ -#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */ -#define SDRAM_RES_SIZE 0x00200000 /* 2 MB for framebuffer */ - -/* SDRAM timing: drive GPL5 high on first cycle */ -#define CONFIG_SYS_OR_TIMING_SDRAM (OR_G5LS) - -#define CONFIG_SYS_OR1_PRELIM ((~(SDRAM_MAX_SIZE)+1)| CONFIG_SYS_OR_TIMING_SDRAM ) -#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -/* - * BR2/OR2 - DIMM - */ -#define CONFIG_SYS_OR2 (OR_ACS_DIV4) -#define CONFIG_SYS_BR2 (BR_MS_UPMA) - -/* - * BR3/OR3 - DIMM - */ -#define CONFIG_SYS_OR3 (OR_ACS_DIV4) -#define CONFIG_SYS_BR3 (BR_MS_UPMA) - -/* - * BR4/OR4 - */ -#define CONFIG_SYS_OR4 0 -#define CONFIG_SYS_BR4 0 - -/* - * BR5/OR5 - */ -#define CONFIG_SYS_OR5 0 -#define CONFIG_SYS_BR5 0 - -/* - * BR6/OR6 - */ -#define CONFIG_SYS_OR6 0 -#define CONFIG_SYS_BR6 0 - -/* - * BR7/OR7 - */ -#define CONFIG_SYS_OR7 0 -#define CONFIG_SYS_BR7 0 - - -/*----------------------------------------------------------------------- - * Debug Entry Mode - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -#endif /* __CONFIG_H */ |