diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/PMC405DE.h | 378 |
1 files changed, 378 insertions, 0 deletions
diff --git a/include/configs/PMC405DE.h b/include/configs/PMC405DE.h new file mode 100644 index 0000000..5232745 --- /dev/null +++ b/include/configs/PMC405DE.h @@ -0,0 +1,378 @@ +/* + * (C) Copyright 2009 + * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd.eu + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_405EP 1 /* This is a PPC405 CPU */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_PMC405DE 1 /* ...on a PMC405DE board */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#undef CONFIG_BOOTARGS +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change*/ + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address */ +#define CONFIG_PHY1_ADDR 2 /* 2nd PHY address */ + +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BSP +#define CONFIG_CMD_CHIP_CONFIG +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING + +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ +#define CONFIG_PRAM 0 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console info */ + +#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x3000000 /* 1 ... 48 MB in DRAM */ + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK +#define CONFIG_SYS_BASE_BAUD 691200 +#define CONFIG_UART1_CONSOLE + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n", bootdelay +#undef CONFIG_AUTOBOOT_DELAY_STR +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * PCI stuff + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +/* + * PCI identification + */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH +#define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x040e /* Dev ID: Non-Monarch */ +#define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x040f /* Dev ID: Monarch */ +#define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC +#define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST + +#define CONFIG_SYS_PCI_CLASSCODE CONFIG_SYS_PCI_CLASSCODE_MONARCH +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH + +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable=1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0xef000000 /* point to CPLD, GPIO */ +#define CONFIG_SYS_PCI_PTM2MS 0xff000001 /* 16MB, enable=1 */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) +/* + * FLASH organization + */ +#define CONFIG_SYS_FLASH_CFI 1 /* CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ + +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max. no. memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* erase timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* write timeout (in ms) */ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* buffered writes (faster) */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* 'E' for empty sector (flinfo) */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xfe000000 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (~(TEXT_BASE) + 1) +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) + +/* + * Environment in EEPROM setup + */ +#define CONFIG_ENV_IS_IN_EEPROM 1 +#define CONFIG_ENV_OFFSET 0x100 +#define CONFIG_ENV_SIZE 0x700 + +/* + * I2C EEPROM (24W16) for environment + */ +#define CONFIG_HARD_I2C /* I2c with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24W16 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ + /* 16 byte page write mode using*/ + /* last 4 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_WREN 1 + +#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50 +#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0x40 +#define CONFIG_4xx_CONFIG_BLOCKSIZE 0x20 + +/* + * RTC + */ +#define CONFIG_RTC_RX8025 + +/* + * External Bus Controller (EBC) Setup + * (max. 55MHZ EBC clock) + */ +/* Memory Bank 0 (NOR flash) BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit */ +#define CONFIG_SYS_EBC_PB0AP 0x03017200 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xba000) + +/* Memory Bank 1 (CPLD) BAS=0xEF0,BS=16MB,BU=R/W,BW=16bit */ +#define CONFIG_SYS_CPLD_BASE 0xef000000 +#define CONFIG_SYS_EBC_PB1AP 0x00800000 +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000) + +/* + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +/* inside SDRAM */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR +/* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes res. for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * GPIO Configuration + */ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alt1 */ \ +{ \ +/* GPIO Core 0 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO6 TS4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO7 TS5 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO9 TrcClk */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \ +} \ +} + +#define CONFIG_SYS_GPIO_HWREV_MASK (0xf0000000 >> 1) /* GPIO1..4 */ +#define CONFIG_SYS_GPIO_HWREV_SHIFT 27 +#define CONFIG_SYS_GPIO_LEDRUN_N (0x80000000 >> 5) /* GPIO5 */ +#define CONFIG_SYS_GPIO_LEDA_N (0x80000000 >> 6) /* GPIO6 */ +#define CONFIG_SYS_GPIO_LEDB_N (0x80000000 >> 7) /* GPIO7 */ +#define CONFIG_SYS_GPIO_SELFRST_N (0x80000000 >> 8) /* GPIO8 */ +#define CONFIG_SYS_GPIO_EEPROM_WP (0x80000000 >> 9) /* GPIO9 */ +#define CONFIG_SYS_GPIO_MONARCH_N (0x80000000 >> 11) /* GPIO11 */ +#define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 12) /* GPIO12 */ +#define CONFIG_SYS_GPIO_M66EN (0x80000000 >> 13) /* GPIO13 */ + +/* + * Default speed selection (cpu_plb_opb_ebc) in mhz. + * This value will be set if iic boot eprom is disabled. + */ +#undef CONFIG_SYS_FCPU333MHZ +#define CONFIG_SYS_FCPU266MHZ +#undef CONFIG_SYS_FCPU133MHZ + +#if defined(CONFIG_SYS_FCPU333MHZ) +/* + * CPU: 333MHz + * PLB/SDRAM/MAL: 111MHz + * OPB: 55MHz + * EBC: 55MHz + * PCI: 55MHz (111MHz on M66EN=1) + */ +#define PLLMR0_DEFAULT (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ + PLL_MALDIV_1 | PLL_PCIDIV_2) +#define PLLMR1_DEFAULT (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) +#endif + +#if defined(CONFIG_SYS_FCPU266MHZ) +/* + * CPU: 266MHz + * PLB/SDRAM/MAL: 133MHz + * OPB: 66MHz + * EBC: 44MHz + * PCI: 44MHz (66MHz on M66EN=1) + */ +#define PLLMR0_DEFAULT (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + PLL_MALDIV_1 | PLL_PCIDIV_3) +#define PLLMR1_DEFAULT (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) +#endif + +#if defined(CONFIG_SYS_FCPU133MHZ) +/* + * CPU: 133MHz + * PLB/SDRAM/MAL: 133MHz + * OPB: 66MHz + * EBC: 44MHz + * PCI: 44MHz (66MHz on M66EN=1) + */ +#define PLLMR0_DEFAULT (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + PLL_MALDIV_1 | PLL_PCIDIV_3) +#define PLLMR1_DEFAULT (PLL_FBKDIV_4 | \ + PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) +#endif + +#endif /* __CONFIG_H */ |