diff options
Diffstat (limited to 'include')
82 files changed, 2069 insertions, 1945 deletions
diff --git a/include/commproc.h b/include/commproc.h index 762238e..a69a809 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -579,34 +579,6 @@ typedef struct scc_enet { /*********************************************************************/ - -/*** CCM and PCU E ***********************************************/ - -/* The PCU E and CCM use the FEC on a MPC860T for Ethernet */ - -#if defined (CONFIG_PCU_E) || defined(CONFIG_CCM) - -#define FEC_ENET /* use FEC for EThernet */ -#undef SCC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -#endif /* CONFIG_PCU_E, CONFIG_CCM */ - /*** ELPT860 *********************************************************/ #ifdef CONFIG_ELPT860 diff --git a/include/compiler.h b/include/compiler.h index 23f4b83..91dbe56 100644 --- a/include/compiler.h +++ b/include/compiler.h @@ -47,7 +47,6 @@ #elif defined(__MACH__) # include <machine/endian.h> typedef unsigned long ulong; -typedef unsigned int uint; #endif typedef uint8_t __u8; diff --git a/include/config_cmd_all.h b/include/config_cmd_all.h index 746bf18..cdc5ff1 100644 --- a/include/config_cmd_all.h +++ b/include/config_cmd_all.h @@ -70,6 +70,7 @@ #define CONFIG_CMD_PORTIO /* Port I/O */ #define CONFIG_CMD_REGINFO /* Register dump */ #define CONFIG_CMD_REISER /* Reiserfs support */ +#define CONFIG_CMD_RARP /* rarpboot support */ #define CONFIG_CMD_RUN /* run command in env variable */ #define CONFIG_CMD_SAVEENV /* saveenv */ #define CONFIG_CMD_SAVES /* save S record dump */ diff --git a/include/configs/BAB7xx.h b/include/configs/BAB7xx.h index 4d83786..555145e 100644 --- a/include/configs/BAB7xx.h +++ b/include/configs/BAB7xx.h @@ -269,6 +269,7 @@ * PCI stuff */ #define CONFIG_PCI /* include pci support */ +#define CONFIG_SYS_EARLY_PCI_INIT #define CONFIG_PCI_PNP /* pci plug-and-play */ #define CONFIG_PCI_HOST PCI_HOST_AUTO #undef CONFIG_PCI_SCAN_SHOW diff --git a/include/configs/CCM.h b/include/configs/CCM.h deleted file mode 100644 index 3f4a2c1..0000000 --- a/include/configs/CCM.h +++ /dev/null @@ -1,488 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * configuration options, board specific, for Siemens Card Controller Module - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#undef CCM_80MHz /* define for 80 MHz CPU only */ - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC860 1 /* This is a MPC860 CPU ... */ -#define CONFIG_CCM 1 /* on a Card Controller Module */ -#define CONFIG_MISC_INIT_R /* Call misc_init_r() */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE - -/* ENVIRONMENT */ - -#define CONFIG_BAUDRATE 19200 /* console baudrate in bps */ -#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */ - -#define CONFIG_IPADDR 192.168.0.42 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 0.0.0.0 -#define CONFIG_SERVERIP 192.168.0.254 - -#define CONFIG_HOSTNAME CCM - -#define CONFIG_LOADADDR 40180000 - -#undef CONFIG_BOOTARGS - -#define CONFIG_BOOTCOMMAND "setenv bootargs " \ - "mem=${mem} " \ - "root=/dev/ram rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \ - "wt_8xx=timeout:3600; " \ - "bootm" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#define CONFIG_WATCHDOG 1 /* watchdog enabled */ - -#undef CONFIG_STATUS_LED /* Status LED disabled */ - -#define CONFIG_PRAM 512 /* reserve 512kB "protected RAM"*/ - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - -#define CONFIG_SPI /* enable SPI driver */ -#define CONFIG_SPI_X /* 16 bit EEPROM addressing */ - -/* ---------------------------------------------------------------- - * Offset to initial SPI buffers in DPRAM (used if the environment - * is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to - * use at an early stage. It is used between the two initialization - * calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it - * far enough from the start of the data area (as well as from the - * stack pointer). - * ---------------------------------------------------------------- */ -#define CONFIG_SYS_SPI_INIT_OFFSET 0xB00 - -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-byte page size */ - - -#define CONFIG_MAC_PARTITION /* nod used yet */ -#define CONFIG_DOS_PARTITION - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/* Ethernet hardware configuration done using port pins */ -#define CONFIG_SYS_PA_ETH_RESET 0x0200 /* PA 6 */ -#define CONFIG_SYS_PA_ETH_MDDIS 0x4000 /* PA 1 */ -#define CONFIG_SYS_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */ -#define CONFIG_SYS_PB_ETH_CFG1 0x00000400 /* PB 21 */ -#define CONFIG_SYS_PB_ETH_CFG2 0x00000200 /* PB 22 */ -#define CONFIG_SYS_PB_ETH_CFG3 0x00000100 /* PB 23 */ - -/* Ethernet settings: - * MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex - */ -#define CONFIG_SYS_ETH_MDDIS_VALUE 0 -#define CONFIG_SYS_ETH_CFG1_VALUE 1 -#define CONFIG_SYS_ETH_CFG2_VALUE 1 -#define CONFIG_SYS_ETH_CFG3_VALUE 1 - -/* PUMA configuration */ -#define CONFIG_SYS_PC_PUMA_PROG 0x0200 /* PC 6 */ -#define CONFIG_SYS_PC_PUMA_DONE 0x0008 /* PC 12 */ -#define CONFIG_SYS_PC_PUMA_INIT 0x0004 /* PC 13 */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xF0000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Address accessed to reset the board - must not be mapped/assigned - */ -#define CONFIG_SYS_RESET_ADDRESS 0xFEFFFFFF - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#if defined(DEBUG) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#if 1 -/* Start port with environment in flash; switch to SPI EEPROM later */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#else -/* Final version: environment in EEPROM */ -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 2048 -#define CONFIG_ENV_SIZE 2048 -#endif - -/*----------------------------------------------------------------------- - * Hardware Information Block - */ -#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * we must activate GPL5 in the SIUMCR for CAN - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - * - * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! - */ -#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ -#define CONFIG_SYS_PLPRCR \ - ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST ) -#else /* up to 50 MHz we use a 1:1 clock */ -#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) -#endif /* CCM_80MHz */ - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ -#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) -#else /* up to 50 MHz we use a 1:1 clock */ -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) -#endif /* CCM_80MHz */ - -/*----------------------------------------------------------------------- - * - * Interrupt Levels - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ - OR_SCY_5_CLK | OR_EHTR) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM -#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) - -/* - * BR2 and OR2 (SDRAM) - * - */ -#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ -#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */ -#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ - -/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 - -#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM ) -#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -/* - * BR3 and OR3 (CAN Controller) - */ -#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ -#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ -#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI) -#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \ - BR_PS_8 | BR_MS_UPMB | BR_V ) - -/* - * BR4/OR4: PUMA Config - * - * Memory controller will be used in 2 modes: - * - * - "read" mode: - * BR4: 0x10100801 OR4: 0xffff8520 - * - "load" mode (chip select on UPM B): - * BR4: 0x101004c1 OR4: 0xffff8600 - * - * Default initialization is in "read" mode - */ -#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */ -#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */ -#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 | OR_SCY_2_CLK) -#define PUMA_CONF_READ_TIMING (OR_G5LA | OR_BI | OR_SCY_2_CLK) - -#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) | \ - BR_PS_8 | BR_MS_UPMB | BR_V) -#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING) - -#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING) - -#define CONFIG_SYS_BR4_PRELIM PUMA_CONF_BR_READ -#define CONFIG_SYS_OR4_PRELIM PUMA_CONF_OR_READ - -/* - * BR5/OR5: PUMA: SMA Bus 8 Bit - * BR5: 0x10200401 OR5: 0xffe0010a - */ -#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */ -#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */ -#define PUMA_SMA8_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) - -#define CONFIG_SYS_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) - -/* - * BR6/OR6: PUMA: SMA Bus 16 Bit - * BR6: 0x10600801 OR6: 0xffe0010a - */ -#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */ -#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */ -#define PUMA_SMA16_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) - -#define CONFIG_SYS_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) - -/* - * BR7/OR7: PUMA: external Flash - * BR7: 0x10a00801 OR7: 0xfe00010a - */ -#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */ -#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */ -#define PUMA_FLASH_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) - -#define CONFIG_SYS_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA) - - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ - -/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/CPC45.h b/include/configs/CPC45.h index 668cfa2..6451263 100644 --- a/include/configs/CPC45.h +++ b/include/configs/CPC45.h @@ -467,6 +467,7 @@ *----------------------------------------------------------------------- */ #define CONFIG_PCI /* include pci support */ +#define CONFIG_SYS_EARLY_PCI_INIT #undef CONFIG_PCI_PNP #undef CONFIG_PCI_SCAN_SHOW diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 8ffd458..95c0a9f 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2009 Freescale Semiconductor, Inc. + * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -74,6 +74,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_ENABLE_36BIT_PHYS 1 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R 1 #define CONFIG_HWCONFIG #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ @@ -505,8 +506,8 @@ extern unsigned long get_clock_freq(void); #else #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 256K(one sector) for env */ -#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index dcaca2b..da826fc 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -134,6 +134,7 @@ #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_EARLY_INIT_R #define CONFIG_MISC_INIT_R +#define CONFIG_HWCONFIG #define CONFIG_FSL_NGPIXIS #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ @@ -177,14 +178,23 @@ #define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_FSL_DIU_FB -#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) - /* Video */ -/* #define CONFIG_VIDEO */ -#ifdef CONFIG_VIDEO +#undef CONFIG_FSL_DIU_FB + +#ifdef CONFIG_FSL_DIU_FB +#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) +#define CONFIG_VIDEO +#define CONFIG_CMD_BMP #define CONFIG_CFB_CONSOLE #define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +/* + * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so + * disable empty flash sector detection, which is I/O-intensive. + */ +#undef CONFIG_SYS_FLASH_EMPTY_INFO #endif /* diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h index adb6ac5..ba3ada1 100644 --- a/include/configs/SMN42.h +++ b/include/configs/SMN42.h @@ -198,6 +198,6 @@ #define CONFIG_INITRD_TAG #define CONFIG_MMC 1 /* we use this ethernet chip */ -#define CONFIG_ENC28J60 +#define CONFIG_ENC28J60_LPC2292 #endif /* __CONFIG_H */ diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h new file mode 100644 index 0000000..a54ab1d --- /dev/null +++ b/include/configs/a4m072.h @@ -0,0 +1,387 @@ +/* + * (C) Copyright 2003-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2010 + * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */ +#define CONFIG_A4M072 1 /* ... on A4M072 board */ +#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ + +#define CONFIG_MISC_INIT_R + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +/* define to enable silent console */ +#define CONFIG_SILENT_CONSOLE +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ + +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +#define CONFIG_PCI + +#if defined(CONFIG_PCI) +#define CONFIG_PCI_PNP 1 +#define CONFIG_PCI_SCAN_SHOW 1 +#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 +#endif + +#define CONFIG_SYS_XLB_PIPELINING 1 + +#undef CONFIG_NET_MULTI +#undef CONFIG_EEPRO100 + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +/* USB */ +#define CONFIG_USB_OHCI_NEW +#define CONFIG_USB_STORAGE +#define CONFIG_SYS_OHCI_BE_CONTROLLER +#undef CONFIG_SYS_USB_OHCI_BOARD_INIT +#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 +#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_NFS +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB +#define CONFIG_CMD_MII +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_DISPLAY + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#endif + +#if (TEXT_BASE == 0xFE000000) /* Boot low with 32 MB Flash */ +#define CONFIG_SYS_LOWBOOT 1 +#define CONFIG_SYS_LOWBOOT32 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */ + +#define CONFIG_SYS_AUTOLOAD "n" + +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR "asdfg" + +#undef CONFIG_BOOTARGS +#define CONFIG_PREBOOT "run try_update" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bk=run add_mtd ; run add_consolespec ; bootm 200000\0" \ + "cf1=diskboot 200000 0:1\0" \ + "bootcmd_cf1=run bcf1\0" \ + "bcf=setenv bootargs root=/dev/hda3\0" \ + "bootcmd_nfs=run bnfs\0" \ + "norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs\0" \ + "bootcmd_nor=cp.b ${kernel_addr} 200000 100000; run norargs addip; run bk\0" \ + "bnfs=nfs 200000 ${rootpath}/boot/uImage ; run nfsargs addip ; run bk\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \ + "try_update=usb start;sleep 2;usb start;sleep 1;fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;source 2F0000\0" \ + "env_addr=FE060000\0" \ + "kernel_addr=FE100000\0" \ + "rootfs_addr=FE200000\0" \ + "add_mtd=setenv bootargs ${bootargs} mtdparts=phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0" \ + "bcf1=run cf1; run bcf; run addip; run bk\0" \ + "add_consolespec=setenv bootargs ${bootargs} console=/dev/null quiet\0" \ + "addip=if test \"${ethaddr}\" != \"00:00:00:00:00:00\" ; then if test -n ${ipaddr}; then setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off panic=1; fi ; fi\0" \ + "hostname=CPUP0\0" \ + "ethaddr=00:00:00:00:00:00\0" \ + "netdev=eth0\0" \ + "bootcmd=run bootcmd_nor\0" \ + "" +/* + * IPB Bus clocking configuration. + */ +#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ + +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_EEPROM_WREN 1 +#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4 + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define CONFIG_SYS_FLASH_SIZE 0x02000000 +#if !defined(CONFIG_SYS_LOWBOOT) +#error "CONFIG_SYS_LOWBOOT not defined?" +#else /* CONFIG_SYS_LOWBOOT */ +#if defined(CONFIG_SYS_LOWBOOT32) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) +#endif +#endif /* CONFIG_SYS_LOWBOOT */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_CS0_START} + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +#define CONFIG_ENV_OVERWRITE 1 + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +/* Use SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ + + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +/* + * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb + */ +/* #define CONFIG_MPC5xxx_FEC_MII10 */ +#define CONFIG_PHY_ADDR 0x1f +#define CONFIG_PHY_TYPE 0x79c874 /* AMD Phy Controller */ + +/* + * GPIO configuration + */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0x18000004 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_CMDLINE_EDITING 1 +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE +/* Flash at CSBoot, CS0 */ +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x0002DD00 +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE +/* External SRAM at CS1 */ +#define CONFIG_SYS_CS1_START 0x62000000 +#define CONFIG_SYS_CS1_SIZE 0x00400000 +#define CONFIG_SYS_CS1_CFG 0x00009930 +#define CONFIG_SYS_SRAM_BASE CONFIG_SYS_CS1_START +#define CONFIG_SYS_SRAM_SIZE CONFIG_SYS_CS1_SIZE +/* LED display at CS7 */ +#define CONFIG_SYS_CS7_START 0x6a000000 +#define CONFIG_SYS_CS7_SIZE (64*1024) +#define CONFIG_SYS_CS7_CFG 0x0000bf30 + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333003 + +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 + +/*----------------------------------------------------------------------- + * USB stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_USB_CLOCK 0x0001BBBB +#define CONFIG_USB_CONFIG 0x00001000 /* 0x4000 for SE mode */ + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_IDE_PREINIT + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#define CONFIG_ATAPI 1 + +/*----------------------------------------------------------------------- + * Open firmware flat tree support + *----------------------------------------------------------------------- + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" + +/* Support for the 7-segment display */ +#define CONFIG_SYS_DISP_CHR_RAM CONFIG_SYS_CS7_START +#define CONFIG_SHOW_ACTIVITY /* used for display realization */ + +#define CONFIG_SHOW_BOOT_PROGRESS + +#endif /* __CONFIG_H */ diff --git a/include/configs/bct-brettl2.h b/include/configs/bct-brettl2.h new file mode 100644 index 0000000..09691d3 --- /dev/null +++ b/include/configs/bct-brettl2.h @@ -0,0 +1,155 @@ +/* + * U-boot - Configuration file for BF536 brettl2 board + */ + +#ifndef __CONFIG_BCT_BRETTL2_H__ +#define __CONFIG_BCT_BRETTL2_H__ + +#include <asm/config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 16384000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 24 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 3 +#define CONFIG_VR_CTL_VAL (VLEV_110 | GAIN_20 | FREQ_1000) + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 9 +#define CONFIG_MEM_SIZE 32 + + +/* + * SDRAM Settings + */ +#define CONFIG_EBIU_SDRRC_VAL 0x07f6 +#define CONFIG_EBIU_SDGCTL_VAL 0x9111cd + +#define CONFIG_EBIU_AMGCTL_VAL (AMBEN_ALL) +#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3) +#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_7 | B3RAT_11 | B3HT_2 | B3ST_3 | B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3) + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) + + +/* + * Network Settings + */ +#ifndef __ADSPBF534__ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_BFIN_MAC 1 +#define CONFIG_NETCONSOLE 1 +#define CONFIG_NET_MULTI 1 +#define CONFIG_HOSTNAME brettl2 +#define CONFIG_IPADDR 192.168.233.224 +#define CONFIG_GATEWAYIP 192.168.233.1 +#define CONFIG_SERVERIP 192.168.233.53 +#define CONFIG_ROOTPATH /romfs/brettl2 +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ +#endif + + +/* + * Flash Settings + */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 135 + + +/* + * Env Storage Settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 + +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED +#else +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#endif + +#ifdef ENV_IS_EMBEDDED +/* WARNING - the following is hand-optimized to fit within + * the sector before the environment sector. If it throws + * an error during compilation remove an object here to get + * it linked after the configuration sector. + */ +# define LDS_BOARD_TEXT \ + arch/blackfin/cpu/traps.o (.text .text.*); \ + arch/blackfin/cpu/interrupt.o (.text .text.*); \ + arch/blackfin/cpu/serial.o (.text .text.*); \ + common/dlmalloc.o (.text .text.*); \ + lib/crc32.o (.text .text.*); \ + . = DEFINED(env_offset) ? env_offset : .; \ + common/env_embedded.o (.text .text.*); +#endif + + +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 + + +/* + * Misc Settings + */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_LOADADDR 0x800000 +#define CONFIG_MISC_INIT_R +#define CONFIG_UART_CONSOLE 0 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +/* disable unnecessary features */ +#undef CONFIG_BOOTM_RTEMS +#undef CONFIG_BZIP2 +#undef CONFIG_KALLSYMS + +#endif diff --git a/include/configs/bf518f-ezbrd.h b/include/configs/bf518f-ezbrd.h index 6eec1c9..64ca9ed 100644 --- a/include/configs/bf518f-ezbrd.h +++ b/include/configs/bf518f-ezbrd.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf518-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA diff --git a/include/configs/bf526-ezbrd.h b/include/configs/bf526-ezbrd.h index 82396d0..4c30c25 100644 --- a/include/configs/bf526-ezbrd.h +++ b/include/configs/bf526-ezbrd.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf526-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA @@ -53,7 +52,7 @@ #define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_15 | B1RAT_15 | B1HT_3 | B1RDYPOL | B0WAT_15 | B0RAT_15 | B0HT_3 | B0RDYPOL) #define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_15 | B3RAT_15 | B3HT_3 | B3RDYPOL | B2WAT_15 | B2RAT_15 | B2HT_3 | B2RDYPOL) -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) #define CONFIG_SYS_MALLOC_LEN (512 * 1024) @@ -62,7 +61,8 @@ * (can't be used same time as ethernet) */ #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) -#define CONFIG_BFIN_NFC +# define CONFIG_BFIN_NFC +# define CONFIG_BFIN_NFC_BOOTROM_ECC #endif #ifdef CONFIG_BFIN_NFC #define CONFIG_BFIN_NFC_CTL_VAL 0x0033 diff --git a/include/configs/bf527-ad7160-eval.h b/include/configs/bf527-ad7160-eval.h index eb3a2b7..14ade1b 100644 --- a/include/configs/bf527-ad7160-eval.h +++ b/include/configs/bf527-ad7160-eval.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf527-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER @@ -130,7 +129,7 @@ #define CONFIG_MMC #define CONFIG_CMD_EXT2 #define CONFIG_SPI_MMC -#define CONFIG_SPI_MMC_DEFAULT_CS (7 + GPIO_PH3) +#define CONFIG_SPI_MMC_DEFAULT_CS (MAX_CTRL_CS + GPIO_PH3) /* diff --git a/include/configs/bf527-ezkit.h b/include/configs/bf527-ezkit.h index 07e4ce8..54fc063 100644 --- a/include/configs/bf527-ezkit.h +++ b/include/configs/bf527-ezkit.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf527-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA diff --git a/include/configs/bf527-sdp.h b/include/configs/bf527-sdp.h new file mode 100644 index 0000000..3582846 --- /dev/null +++ b/include/configs/bf527-sdp.h @@ -0,0 +1,121 @@ +/* + * U-boot - Configuration file for BF527 SDP board + */ + +#ifndef __CONFIG_BF527_SDP_H__ +#define __CONFIG_BF527_SDP_H__ + +#include <asm/config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 24000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 25 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 + +#define CONFIG_PLL_LOCKCNT_VAL 0x0200 +#define CONFIG_PLL_CTL_VAL 0x2a00 +#define CONFIG_VR_CTL_VAL 0x7090 + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 9 +#define CONFIG_MEM_SIZE 32 + +#define CONFIG_EBIU_SDRRC_VAL 0x00FE +#define CONFIG_EBIU_SDGCTL_VAL 0x8011998d + +#define CONFIG_EBIU_AMGCTL_VAL (AMCKEN | AMBEN_ALL) +#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_15 | B1RAT_15 | B1HT_3 | B1RDYPOL | B0WAT_15 | B0RAT_15 | B0HT_3 | B0RDYPOL) +#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_15 | B3RAT_15 | B3HT_3 | B3RDYPOL | B2WAT_15 | B2RAT_15 | B2HT_3 | B2RDYPOL) + +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (640 * 1024) + + +/* + * Flash Settings + */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 259 + + +/* + * SPI Settings + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ALL + + +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#endif + + +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 + + +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_UART_CONSOLE 0 + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +#endif diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h index 95d3afa..e1bb594 100644 --- a/include/configs/bf533-ezkit.h +++ b/include/configs/bf533-ezkit.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf533-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index f39bfee..03bc811 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf533-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS @@ -93,10 +92,7 @@ #define CONFIG_ENV_SPI_MAX_HZ 30000000 #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_ATMEL -#define CONFIG_SPI_FLASH_SPANSION -#define CONFIG_SPI_FLASH_STMICRO -#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_ALL /* diff --git a/include/configs/bf537-minotaur.h b/include/configs/bf537-minotaur.h index 86aa1f6..0ba29bc 100644 --- a/include/configs/bf537-minotaur.h +++ b/include/configs/bf537-minotaur.h @@ -24,7 +24,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER diff --git a/include/configs/bf537-pnav.h b/include/configs/bf537-pnav.h index 39bbb41..730ae27 100644 --- a/include/configs/bf537-pnav.h +++ b/include/configs/bf537-pnav.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER @@ -52,7 +51,7 @@ #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB033B0 #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) #define CONFIG_SYS_MALLOC_LEN (128 * 1024) diff --git a/include/configs/bf537-srv1.h b/include/configs/bf537-srv1.h index 7e9dd36..559428f 100644 --- a/include/configs/bf537-srv1.h +++ b/include/configs/bf537-srv1.h @@ -24,7 +24,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index fc9784e..22d3150 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS @@ -89,10 +88,7 @@ #define CONFIG_ENV_SPI_MAX_HZ 30000000 #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_ATMEL -#define CONFIG_SPI_FLASH_SPANSION -#define CONFIG_SPI_FLASH_STMICRO -#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_ALL /* diff --git a/include/configs/bf538f-ezkit.h b/include/configs/bf538f-ezkit.h index 1c14b6b..04ba210 100644 --- a/include/configs/bf538f-ezkit.h +++ b/include/configs/bf538f-ezkit.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf538-0.4 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS @@ -86,10 +85,7 @@ #define CONFIG_ENV_SPI_MAX_HZ 30000000 #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_ATMEL -#define CONFIG_SPI_FLASH_SPANSION -#define CONFIG_SPI_FLASH_STMICRO -#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_ALL /* diff --git a/include/configs/bf548-ezkit.h b/include/configs/bf548-ezkit.h index 60cca0c..4412177 100644 --- a/include/configs/bf548-ezkit.h +++ b/include/configs/bf548-ezkit.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf548-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA @@ -183,6 +182,7 @@ #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_RTC_BFIN #define CONFIG_UART_CONSOLE 1 +#define CONFIG_BFIN_SPI_IMG_SIZE 0x50000 #ifndef __ADSPBF542__ /* Don't waste time transferring a logo over the UART */ diff --git a/include/configs/bf561-acvilon.h b/include/configs/bf561-acvilon.h index 0c0204f..2b12c3f 100644 --- a/include/configs/bf561-acvilon.h +++ b/include/configs/bf561-acvilon.h @@ -12,7 +12,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf561-0.5 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h index 4e293b5..1557e14 100644 --- a/include/configs/bf561-ezkit.h +++ b/include/configs/bf561-ezkit.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf561-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index 91dcacc..608788a 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -47,6 +47,7 @@ # endif # if defined(CONFIG_NAND_PLAT) || defined(CONFIG_DRIVER_NAND_BFIN) # define CONFIG_CMD_NAND +# define CONFIG_CMD_NAND_LOCK_UNLOCK # endif # ifdef CONFIG_POST # define CONFIG_CMD_DIAG @@ -119,10 +120,12 @@ /* * Env Settings */ -#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) -# define CONFIG_BOOTDELAY -1 -#else -# define CONFIG_BOOTDELAY 5 +#ifndef CONFIG_BOOTDELAY +# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) +# define CONFIG_BOOTDELAY -1 +# else +# define CONFIG_BOOTDELAY 5 +# endif #endif #ifndef CONFIG_BOOTCOMMAND # define CONFIG_BOOTCOMMAND "run ramboot" @@ -169,9 +172,12 @@ # define UBOOT_ENV_UPDATE \ "eeprom write $(loadaddr) 0x0 $(filesize)" # else +# ifndef CONFIG_BFIN_SPI_IMG_SIZE +# define CONFIG_BFIN_SPI_IMG_SIZE 0x40000 +# endif # define UBOOT_ENV_UPDATE \ "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \ - "sf erase 0 0x40000;" \ + "sf erase 0 " MK_STR(CONFIG_BFIN_SPI_IMG_SIZE) ";" \ "sf write $(loadaddr) 0 $(filesize)" # endif # elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) @@ -231,20 +237,28 @@ #else # define NETWORK_ENV_SETTINGS #endif +#ifndef BOARD_ENV_SETTINGS +# define BOARD_ENV_SETTINGS +#endif #define CONFIG_EXTRA_ENV_SETTINGS \ NAND_ENV_SETTINGS \ NETWORK_ENV_SETTINGS \ - FLASHBOOT_ENV_SETTINGS + FLASHBOOT_ENV_SETTINGS \ + BOARD_ENV_SETTINGS /* * Network Settings */ #ifdef CONFIG_CMD_NET -# define CONFIG_IPADDR 192.168.0.15 # define CONFIG_NETMASK 255.255.255.0 -# define CONFIG_GATEWAYIP 192.168.0.1 -# define CONFIG_SERVERIP 192.168.0.2 -# define CONFIG_ROOTPATH /romfs +# ifndef CONFIG_IPADDR +# define CONFIG_IPADDR 192.168.0.15 +# define CONFIG_GATEWAYIP 192.168.0.1 +# define CONFIG_SERVERIP 192.168.0.2 +# endif +# ifndef CONFIG_ROOTPATH +# define CONFIG_ROOTPATH /romfs +# endif # ifdef CONFIG_CMD_DHCP # ifndef CONFIG_SYS_AUTOLOAD # define CONFIG_SYS_AUTOLOAD "no" @@ -255,6 +269,18 @@ #endif /* + * SPI Settings + */ +#ifdef CONFIG_SPI_FLASH_ALL +# define CONFIG_SPI_FLASH_ATMEL +# define CONFIG_SPI_FLASH_MACRONIX +# define CONFIG_SPI_FLASH_SPANSION +# define CONFIG_SPI_FLASH_SST +# define CONFIG_SPI_FLASH_STMICRO +# define CONFIG_SPI_FLASH_WINBOND +#endif + +/* * I2C Settings */ #if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h index 85f08ea..3f5c959 100644 --- a/include/configs/blackstamp.h +++ b/include/configs/blackstamp.h @@ -24,7 +24,6 @@ /* CPU Options * Be sure to set the Silicon Revision Correctly */ -#define CONFIG_BFIN_CPU bf532-0.5 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER /* diff --git a/include/configs/blackvme.h b/include/configs/blackvme.h new file mode 100644 index 0000000..8b2bdc7 --- /dev/null +++ b/include/configs/blackvme.h @@ -0,0 +1,246 @@ +/* U-boot for BlackVME. (C) Wojtek Skulski 2010. + * The board includes ADSP-BF561 rev. 0.5, + * 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG), + * Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell), + * SPI boot flash on PF2 (M25P64 8MB, or M25P128 16 MB), + * FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB), + * Spartan6-LX150 (memory-mapped; both PPIs also connected). + * See http://www.skutek.com + */ + +#ifndef __CONFIG_BLACKVME_H__ +#define __CONFIG_BLACKVME_H__ + +#include <asm/config-pre.h> + +/* Debugging: Set these options if you're having problems + * #define CONFIG_DEBUG_EARLY_SERIAL + * #define DEBUG + * #define CONFIG_DEBUG_DUMP + * #define CONFIG_DEBUG_DUMP_SYMS + * CONFIG_PANIC_HANG means that the board will not auto-reboot + */ +#define CONFIG_PANIC_HANG 0 + +/* CPU Options */ +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER + +/* + * CLOCK SETTINGS CAVEAT + * You CANNOT just change the clock settings, esp. the SCLK. + * The SDRAM timing, SPI baud, and the serial UART baud + * use SCLK frequency to set their own frequencies. Therefore, + * if you change the SCLK_DIV, you may also have to adjust + * SDRAM refresh and other timings. + * -------------------------------------------------------------- + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * 25 * 8 / 1 = 200 MHz + * 25 * 16 / 1 = 400 MHz + * 25 * 24 / 1 = 600 MHz + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + * 25 * 8 / 2 = 100 MHz + * 25 * 24 / 6 = 100 MHz + * 25 * 24 / 5 = 120 MHz + * 25 * 16 / 3 = 133 MHz + * 25 MHz because the oscillator also feeds the ether chip. + * CONFIG_CLKIN_HZ is 25 MHz written in Hz + * CLKIN_HALF controls the DF bit in PLL_CTL + * 0 = CLKIN 1 = CLKIN / 2 + * PLL_BYPASS controls the BYPASS bit in PLL_CTL + * 0 = do not bypass 1 = bypass PLL + * VCO_MULT = MSEL (multiplier) in PLL_CTL + * Values can range from 0-63 (where 0 means 64) + * CCLK_DIV = core clock divider (1, 2, 4, or 8 ONLY) + * SCLK_DIV = system clock divider, 1 to 15 + */ +#define CONFIG_CLKIN_HZ 25000000 +#define CONFIG_CLKIN_HALF 0 +#define CONFIG_PLL_BYPASS 0 +#define CONFIG_VCO_MULT 8 +#define CONFIG_CCLK_DIV 1 +#define CONFIG_SCLK_DIV 2 + +/* + * Ether chip in async memory space AMS3, same as BF561-EZ-KIT. + * Used in 32-bit mode. 16-bit mode not supported. + * http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180 + */ +/* + * Network settings using a dedicated 2nd ether card in PC + * Windows will automatically acquire IP of that card + * Then use the dedicated card IP + 1 for the board + * http://docs.blackfin.uclinux.org/doku.php?id=setting_up_the_network + */ +#define CONFIG_NET_MULTI + +#define CONFIG_DRIVER_AX88180 1 +#define AX88180_BASE 0x2c000000 +#define CONFIG_CMD_MII /* enable probing PHY */ + +#ifdef CONFIG_NET_MULTI /* also used as the network enabler */ +# define CONFIG_HOSTNAME blackvme /* Bfin board */ +# define CONFIG_IPADDR 169.254.144.145 /* Bfin board */ +# define CONFIG_GATEWAYIP 169.254.144.144 /* dedic card */ +# define CONFIG_SERVERIP 169.254.144.144 /* tftp server */ +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_ROOTPATH /export/uClinux-dist/romfs /*NFS*/ +# define CFG_AUTOLOAD "no" +# define CONFIG_CMD_DHCP +# define CONFIG_CMD_PING +# define CONFIG_ENV_OVERWRITE 1 /* enable changing MAC at runtime */ +/* Comment out hardcoded MAC to enable MAC storage in EEPROM */ +/* # define CONFIG_ETHADDR ff:ee:dd:cc:bb:aa */ +#endif + +/* + * SDRAM settings & memory map + */ + +#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ +#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ +/* + * SDRAM reference page + * http://docs.blackfin.uclinux.org/doku.php?id=bfin:sdram + * NOTE: BlackVME populates only SDRAM bank 0 + */ +/* CONFIG_EBIU_SDBCTL_VAL bank ctrl may be needed in future */ +#define CONFIG_EBIU_SDGCTL_VAL 0x91114d /* global control */ +#define CONFIG_EBIU_SDRRC_VAL 0x306 /* refresh rate */ + +/* Async memory global settings. (ASRAM, not SDRAM) + * HRM page 16-10. Global ASRAM control = 0x3F. Six lower bits = 1 + * CLKOUT enabled, all async banks enabled, core has priority + * bank 0&1 16 bit (FPGA) + * bank 2&3 32 bit (ether and USB chips) + */ +#define CONFIG_EBIU_AMGCTL_VAL 0x3F /* ASRAM setup */ + +/* Async mem timing: BF561 HRM page 16-12 and 16-15. + * Default values 0xFFC2 FFC2 are the slowest supported. + * Example settings of CONFIG_EBIU_AMBCTL1_VAL + * 1. EZ-KIT settings: 0xFFC2 7BB0 + * 2. Bank 3 good timing for AX88180 @ 125MHz = 0x8850 xxxx + * See the following page: + * http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180 + * 3. Bank 3 timing for AX88180 @ SCLK = 100 MHz: + * AX88180 WEN = 5 clocks REN 6 clocks @ SCLK = 100 MHz + * One extra clock needed because AX88180 is asynchronous to CPU. + */ + /* bank 1 0 */ +#define CONFIG_EBIU_AMBCTL0_VAL 0xFFC2FFC2 + /* bank 3 2 */ +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC2FFC2 + +/* memory layout */ + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_SYS_MALLOC_LEN (384 << 10) + +/* + * Serial SPI Flash + * For the M25P64 SCK should be kept < 15 MHz + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x40000 + +#define CONFIG_ENV_SPI_MAX_HZ 15000000 +#define CONFIG_SF_DEFAULT_SPEED 15000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO + +/* + * Interactive command settings + */ + +#define CONFIG_SYS_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE 1 + +#include <config_cmd_default.h> + +#define CONFIG_CMD_BOOTLDR +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_CPLBINFO +#define CONFIG_CMD_SF +#define CONFIG_CMD_ELF + +/* + * Default: boot from SPI flash. + * "sfboot" is a composite command defined in extra settings + */ +#define CONFIG_BOOTDELAY 5 +#define CONFIG_BOOTCOMMAND "run sfboot" + +/* + * Console settings + */ +#define CONFIG_BAUDRATE 57600 +#define CONFIG_LOADS_ECHO 1 +#define CONFIG_UART_CONSOLE 0 + +/* + * U-Boot environment variables. Use "printenv" to examine. + * http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:env + */ +#define CONFIG_BOOTARGS \ + "root=/dev/mtdblock0 rw " \ + "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \ + "earlyprintk=serial,uart0," \ + MK_STR(CONFIG_BAUDRATE) " " \ + "console=ttyBF0," MK_STR(CONFIG_BAUDRATE) " " + +/* Convenience env variables & commands. + * Reserve kernstart = 0x20000 = 128 kB for U-Boot. + * Reserve kernarea = 0x500000 = 5 MB for kernel (reasonable size). + * U-Boot image is saved at flash offset=0. + * Kernel image is saved at flash offset=$kernstart. + * Instructions. Ksave takes about a minute to complete. + * 1. Update U-Boot: run uget; run usave + * 2. Update kernel: run kget; run ksave + * After updating U-Boot also update the kernel per above instructions + * to make the saved environment consistent with the flash. + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kernstart=0x20000\0" \ + "kernarea=0x500000\0" \ + "uget=tftp u-boot.ldr\0" \ + "kget=tftp uImage\0" \ + "usave=sf probe 2; " \ + "sf erase 0 $(kernstart); " \ + "sf write $(fileaddr) 0 $(filesize)\0" \ + "ksave=sf probe 2; " \ + "saveenv; " \ + "echo Now patiently wait for the prompt...; " \ + "sf erase $(kernstart) $(kernarea); " \ + "sf write $(fileaddr) $(kernstart) $(filesize)\0" \ + "sfboot=sf probe 2; " \ + "sf read $(loadaddr) $(kernstart) $(filesize); " \ + "run addip; bootm\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):" \ + "$(netmask):$(hostname):eth0:off\0" + +/* + * Soft I2C settings (BF561 does not have hard I2C) + * PF12,13 on SPI connector 0. + */ +#ifdef CONFIG_SOFT_I2C +# define CONFIG_CMD_I2C +# define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF12 +# define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF13 +# define CONFIG_SYS_I2C_SPEED 50000 +# define CONFIG_SYS_I2C_SLAVE 0xFE +#endif + +/* + * No Parallel Flash on this board + */ +#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_JFFS2 +#undef CONFIG_CMD_FLASH + +#endif diff --git a/include/configs/bluestone.h b/include/configs/bluestone.h new file mode 100644 index 0000000..560c64f --- /dev/null +++ b/include/configs/bluestone.h @@ -0,0 +1,178 @@ +/* + * bluestone.h - configuration for Bluestone (APM821XX) + * + * Copyright (c) 2010, Applied Micro Circuits Corporation + * Author: Tirumala R Marri <tmarri@apm.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_APM821XX 1 /* APM821XX series */ +#define CONFIG_HOSTNAME bluestone + +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_440 1 +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" +#define CONFIG_SYS_CLK_FREQ 50000000 + +#define CONFIG_BOARD_TYPES 1 /* support board types */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +/* EBC stuff */ +/* later mapped to this addr */ +#define CONFIG_SYS_FLASH_BASE 0xFFF00000 +#define CONFIG_SYS_FLASH_SIZE (4 << 20) /* 1MB usable */ + +/* EBC Boot Space: 0xFF000000 */ +#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 +#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 32k */ +#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ +#define CONFIG_SYS_AHB_BASE 0xE2000000 /* internal AHB peripherals*/ + +#define CONFIG_SYS_SRAM_SIZE (256 << 10) +/* + * Initial RAM & stack pointer (placed in OCM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Environment + */ +/* + * Define here the location of the environment variables (FLASH). + */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +/* + * FLASH related + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +/* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 80 +/* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 +/* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 +/* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 +/* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ + +/* SDRAM */ +#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ +#define SPD_EEPROM_ADDRESS {0x53, 0x51} /* SPD i2c spd addresses */ +#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ +#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ +#define CONFIG_DDR_ECC 1 /* with ECC support */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ + +/* + * I2C + */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* Data sheet */ + +/* I2C bootstrap EEPROM */ +#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52 +#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 +#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 + +/* + * Ethernet + */ +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_NONE_RGMII +#define CONFIG_HAS_ETH0 +/* PHY address, See schematics */ +#define CONFIG_PHY_ADDR 0x1f +/* reset phy upon startup */ +#define CONFIG_PHY_RESET 1 +/* Include GbE speed/duplex detection */ +#define CONFIG_PHY_GIGE 1 +#define CONFIG_PHY_DYNAMIC_ANEG 1 + +/* + * External Bus Controller (EBC) Setup + **/ +#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_LOCK | \ + EBC_CFG_PTD_ENABLE | \ + EBC_CFG_RTC_2048PERCLK | \ + EBC_CFG_ATC_HI | \ + EBC_CFG_DTC_HI | \ + EBC_CFG_CTC_HI | \ + EBC_CFG_OEO_PREVIOUS) +/* NOR Flash */ +#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ + EBC_BXAP_TWT_ENCODE(64) | \ + EBC_BXAP_BCE_DISABLE | \ + EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(1) | \ + EBC_BXAP_OEN_ENCODE(2) | \ + EBC_BXAP_WBN_ENCODE(2) | \ + EBC_BXAP_WBF_ENCODE(2) | \ + EBC_BXAP_TH_ENCODE(7) | \ + EBC_BXAP_SOR_DELAYED | \ + EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED) +/* Peripheral Bank Configuration Register - EBC_BxCR */ +#define CONFIG_SYS_EBC_PB0CR \ + (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \ + EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | \ + EBC_BXCR_BW_8BIT) + + +#endif /* __CONFIG_H */ diff --git a/include/configs/ca9x4_ct_vxp.h b/include/configs/ca9x4_ct_vxp.h new file mode 100644 index 0000000..5547d55 --- /dev/null +++ b/include/configs/ca9x4_ct_vxp.h @@ -0,0 +1,196 @@ +/* + * (C) Copyright 2010 Linaro + * Matt Waddel, <matt.waddel@linaro.org> + * + * Configuration for Versatile Express. Parts were derived from other ARM + * configurations. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* Board info register */ +#define SYS_ID 0x10000000 +#define CONFIG_REVISION_TAG 1 + +/* High Level Configuration Options */ +#define CONFIG_ARMV7 1 + +#define CONFIG_SYS_MEMTEST_START 0x60000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_L2_OFF 1 +#define CONFIG_INITRD_TAG 1 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +#define SCTL_BASE 0x10001000 +#define VEXPRESS_FLASHPROG_FLVPPEN (1 << 0) + +/* SMSC9115 Ethernet from SMSC9118 family */ +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X 1 +#define CONFIG_SMC911X_32_BIT 1 +#define CONFIG_SMC911X_BASE 0x4E000000 + +/* PL011 Serial Configuration */ +#define CONFIG_PL011_SERIAL +#define CONFIG_PL011_CLOCK 24000000 +#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ + (void *)CONFIG_SYS_SERIAL1} +#define CONFIG_CONS_INDEX 0 + +#define CONFIG_BAUDRATE 38400 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_SERIAL0 0x10009000 +#define CONFIG_SYS_SERIAL1 0x1000A000 + +/* Command line configuration */ +#define CONFIG_CMD_BDI +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_IMI +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVEENV +#define CONFIG_NET_MULTI +#define CONFIG_CMD_RUN + +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION 1 +#define CONFIG_MMC 1 +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC + +/* BOOTP options */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Miscellaneous configurable options */ +#undef CONFIG_SYS_CLKS_IN_HZ +#define CONFIG_SYS_LOAD_ADDR 0x60008000 /* load address */ +#define LINUX_BOOT_PARAM_ADDR 0x60000200 +#define CONFIG_BOOTDELAY 2 + +/* Stack sizes are set up in start.S using the settings below */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4 * 1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4 * 1024) /* FIQ stack */ +#endif + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 2 +#define PHYS_SDRAM_1 0x60000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_2 0x80000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x20000000 /* 512 MB */ +#define PHYS_SDRAM_2_SIZE 0x20000000 /* 512 MB */ + +/* additions for new relocation code */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_END 0x1000 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET + +/* Basic environment settings */ +#define CONFIG_BOOTCOMMAND "run bootflash;" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80008000\0" \ + "initrd=0x61000000\0" \ + "kerneladdr=0x44100000\0" \ + "initrdaddr=0x44800000\0" \ + "maxinitrd=0x1800000\0" \ + "console=ttyAMA0,38400n8\0" \ + "dram=1024M\0" \ + "root=/dev/sda1 rw\0" \ + "mtd=armflash:1M@0x800000(uboot),7M@0x1000000(kernel)," \ + "24M@0x2000000(initrd)\0" \ + "flashargs=setenv bootargs root=${root} console=${console} " \ + "mem=${dram} mtdparts=${mtd} mmci.fmax=190000 " \ + "devtmpfs.mount=0 vmalloc=256M\0" \ + "bootflash=run flashargs; " \ + "cp ${initrdaddr} ${initrd} ${maxinitrd}; " \ + "bootm ${kerneladdr} ${initrd}\0" + +/* FLASH and environment organization */ +#define PHYS_FLASH_SIZE 0x04000000 /* 64MB */ +#define CONFIG_SYS_FLASH_CFI 1 +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_SIZE 0x04000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_FLASH_BASE0 0x40000000 +#define CONFIG_SYS_FLASH_BASE1 0x44000000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE0 + +/* Timeout values in ticks */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Erase Timeout */ +#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Write Timeout */ + +/* 255 0x40000 sectors + first or last sector may have 4 erase regions = 259 */ +#define CONFIG_SYS_MAX_FLASH_SECT 259 /* Max sectors */ +#define FLASH_MAX_SECTOR_SIZE 0x00040000 /* 256 KB sectors */ + +/* Room required on the stack for the environment data */ +#define CONFIG_ENV_SIZE FLASH_MAX_SECTOR_SIZE + +/* + * Amount of flash used for environment: + * We don't know which end has the small erase blocks so we use the penultimate + * sector location for the environment + */ +#define CONFIG_ENV_SECT_SIZE FLASH_MAX_SECTOR_SIZE +#define CONFIG_ENV_OVERWRITE 1 + +/* Store environment at top of flash */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET (PHYS_FLASH_SIZE - \ + (2 * CONFIG_ENV_SECT_SIZE)) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE1 + \ + CONFIG_ENV_OFFSET) +#define CONFIG_SYS_FLASH_PROTECTION /* The devices have real protection */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE0, \ + CONFIG_SYS_FLASH_BASE1 } + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PROMPT "VExpress# " +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ +#define CONFIG_CMD_SOURCE +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_SYS_MAXARGS 16 /* max command args */ + +#endif diff --git a/include/configs/cm-bf527.h b/include/configs/cm-bf527.h index e0c6d53..84c9309 100644 --- a/include/configs/cm-bf527.h +++ b/include/configs/cm-bf527.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf527-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA diff --git a/include/configs/cm-bf533.h b/include/configs/cm-bf533.h index 7515296..dbc4a5b 100644 --- a/include/configs/cm-bf533.h +++ b/include/configs/cm-bf533.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf533-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/cm-bf537e.h b/include/configs/cm-bf537e.h index 742df9c..df3fe48 100644 --- a/include/configs/cm-bf537e.h +++ b/include/configs/cm-bf537e.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/cm-bf537u.h b/include/configs/cm-bf537u.h index 9def99f..e5b0ecf 100644 --- a/include/configs/cm-bf537u.h +++ b/include/configs/cm-bf537u.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/cm-bf548.h b/include/configs/cm-bf548.h index fa62a8e..27b1cc5 100644 --- a/include/configs/cm-bf548.h +++ b/include/configs/cm-bf548.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf548-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA diff --git a/include/configs/cm-bf561.h b/include/configs/cm-bf561.h index c60401c..8c350bc 100644 --- a/include/configs/cm-bf561.h +++ b/include/configs/cm-bf561.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf561-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index d223a4d..9184eeb 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -399,6 +399,14 @@ #endif #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +/* controller 4, Base address 203000 */ +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ + /* Qman/Bman */ #define CONFIG_SYS_BMAN_NUM_PORTALS 10 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 @@ -607,14 +615,17 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ + "bank_intlv=cs0_cs1\0" \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ - "erase " MK_STR(TEXT_BASE) " +$filesize; " \ - "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ - "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ - "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "ubootaddr=" MK_STR(TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=p4080ds/ramdisk.uboot\0" \ diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index d02b196..e0a3bae 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -138,7 +138,6 @@ #endif /* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ #define CONFIG_SYS_SDRAM_BASE 0xc0000000 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/eNET.h b/include/configs/eNET.h index da2a97d..fc7c1c6 100644 --- a/include/configs/eNET.h +++ b/include/configs/eNET.h @@ -29,8 +29,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -#define CONFIG_RELOC_FIXUP_WORKS - /* * Stuff still to be dealt with - */ diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h index eb3fa57..2c2682c 100644 --- a/include/configs/guruplug.h +++ b/include/configs/guruplug.h @@ -33,59 +33,13 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_GURUPLUG /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ /* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ -/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ @@ -96,18 +50,13 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -143,55 +92,19 @@ "x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ -#define CONFIG_SYS_MEMTEST_END 0x1fffffff /*(_512M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_CMD_MII -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv88e1121 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #define CONFIG_SYS_ALT_MEMTEST diff --git a/include/configs/h2_p2_dbg_board.h b/include/configs/h2_p2_dbg_board.h index e0d823f..a4dea7d 100644 --- a/include/configs/h2_p2_dbg_board.h +++ b/include/configs/h2_p2_dbg_board.h @@ -31,7 +31,7 @@ #ifndef __INCLUDED_H2_P2_DBH_BOARD_H #define __INCLUDED_H2_P2_DBH_BOARD_H -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /* * The Debug board is designed to function with the P2 Sample, H2 diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h index 26992e7..68bf998 100644 --- a/include/configs/hcu4.h +++ b/include/configs/hcu4.h @@ -191,7 +191,7 @@ CONFIG_SYS_POST_ETHER | \ CONFIG_SYS_POST_SPR) -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #undef CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h index f2ab50c..5aa304d 100644 --- a/include/configs/hcu5.h +++ b/include/configs/hcu5.h @@ -208,7 +208,7 @@ CONFIG_SYS_POST_ETHER | \ CONFIG_SYS_POST_SPR) -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h index d40b7a9..8b0b773 100644 --- a/include/configs/hmi1001.h +++ b/include/configs/hmi1001.h @@ -352,6 +352,7 @@ /* Display addresses */ /*---------------------------------------------------------------------*/ +#define CONFIG_PDSP188x #define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38) #define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30) diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h index 53b5197..cd856ac 100644 --- a/include/configs/ibf-dsp561.h +++ b/include/configs/ibf-dsp561.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf561-0.5 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/imx27lite-common.h b/include/configs/imx27lite-common.h index 812e5f2..88e8d3d 100644 --- a/include/configs/imx27lite-common.h +++ b/include/configs/imx27lite-common.h @@ -235,8 +235,7 @@ "mtdids=" MTDIDS_DEFAULT "\0" \ "mtdparts=" MTDPARTS_DEFAULT "\0" \ -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/ip04.h b/include/configs/ip04.h index c024d78..528363c 100644 --- a/include/configs/ip04.h +++ b/include/configs/ip04.h @@ -20,7 +20,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf532-0.5 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_NAND diff --git a/include/configs/keymile-common.h b/include/configs/keymile-common.h index 6c14ca0..62d21f6 100644 --- a/include/configs/keymile-common.h +++ b/include/configs/keymile-common.h @@ -85,6 +85,7 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_BOARD_DRAM_INIT /* Used board specific dram_init */ /* * How to get access to the slot ID. Put this here to make it easy diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 37eaf8f..612a0fe 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -457,7 +457,8 @@ CONFIG_SYS_POST_UART) /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } #define CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ diff --git a/include/configs/km_arm.h b/include/configs/km_arm.h index 8673e6f..faa0f50 100644 --- a/include/configs/km_arm.h +++ b/include/configs/km_arm.h @@ -180,7 +180,7 @@ int get_scl (void); #undef CONFIG_JFFS2_CMDLINE #endif -/* additions for new relocation code, must added to all boards */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_INIT_SP_ADDR (0x00000000 + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/lpc2292sodimm.h b/include/configs/lpc2292sodimm.h index 7ce8d6d..65276a2 100644 --- a/include/configs/lpc2292sodimm.h +++ b/include/configs/lpc2292sodimm.h @@ -156,6 +156,6 @@ #define CONFIG_INITRD_TAG #define CONFIG_MMC 1 /* we use this ethernet chip */ -#define CONFIG_ENC28J60 +#define CONFIG_ENC28J60_LPC2292 #endif /* __CONFIG_H */ diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 72e02f8..4a3b1dc 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007-2008 + * (C) Copyright 2007-2010 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * This program is free software; you can redistribute it and/or @@ -18,58 +18,63 @@ * MA 02111-1307 USA */ -/************************************************************************ +/* * lwmon5.h - configuration for lwmon5 board - ***********************************************************************/ + */ #ifndef __CONFIG_H #define __CONFIG_H -/*----------------------------------------------------------------------- +/* + * Liebherr extra version info + */ +#define CONFIG_IDENT_STRING " - v2.0" + +/* * High Level Configuration Options - *----------------------------------------------------------------------*/ + */ #define CONFIG_LWMON5 1 /* Board is lwmon5 */ #define CONFIG_440EPX 1 /* Specific PPC440EPx */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_BOARD_RESET 1 /* Call board_reset */ +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_early_init_f */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r */ +#define CONFIG_BOARD_POSTCLK_INIT /* Call board_postclk_init */ +#define CONFIG_MISC_INIT_R /* Call misc_init_r */ +#define CONFIG_BOARD_RESET /* Call board_reset */ -/*----------------------------------------------------------------------- +/* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ + */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */ +#define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1) +#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* Reserved for malloc */ #define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_LIME_BASE_0 0xc0000000 -#define CONFIG_SYS_LIME_BASE_1 0xc1000000 -#define CONFIG_SYS_LIME_BASE_2 0xc2000000 -#define CONFIG_SYS_LIME_BASE_3 0xc3000000 -#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 -#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 +#define CONFIG_SYS_LIME_BASE_0 0xc0000000 +#define CONFIG_SYS_LIME_BASE_1 0xc1000000 +#define CONFIG_SYS_LIME_BASE_2 0xc2000000 +#define CONFIG_SYS_LIME_BASE_3 0xc3000000 +#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 +#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 #define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ #define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE1 (CONFIG_SYS_PCI_MEMBASE + 0x10000000) +#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE1 + 0x10000000) +#define CONFIG_SYS_PCI_MEMBASE3 (CONFIG_SYS_PCI_MEMBASE2 + 0x10000000) #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer - *----------------------------------------------------------------------*/ /* + * Initial RAM & stack pointer + * * On LWMON5 we use D-cache as init-ram and stack pointer. We also move * the POST_WORD from OCM to a 440EPx register that preserves it's * content during reset (GPT0_COMP6). This way we reserve the OCM (16k) @@ -77,18 +82,18 @@ */ #define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_INIT_RAM_END (4 << 10) #define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data*/ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +/* unused GPT0 COMP reg */ #define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) - /* unused GPT0 COMP reg */ -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ - /* 440EPx errata CHIP 11 */ #define CONFIG_SYS_OCM_SIZE (16 << 10) +/* 440EPx errata CHIP 11: don't use last 4kbytes */ +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* Additional registers for watchdog timer post test */ - #define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2) #define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1) #define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR @@ -100,9 +105,9 @@ #define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300 #define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00 -/*----------------------------------------------------------------------- +/* * Serial Port - *----------------------------------------------------------------------*/ + */ #define CONFIG_CONS_INDEX 2 /* Use UART1 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL @@ -110,77 +115,80 @@ #define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */ #define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 +#define CONFIG_SERIAL_MULTI #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} -/*----------------------------------------------------------------------- +/* * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + */ +#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ -/*----------------------------------------------------------------------- +/* * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CONFIG_SYS_FLASH0 0xFC000000 #define CONFIG_SYS_FLASH1 0xF8000000 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION /* use hardware flash protection */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CONFIG_SYS_FLASH_QUIET_TEST /* don't warn upon unknown flash */ #define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN) - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -/*----------------------------------------------------------------------- +/* * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ + */ +#define CONFIG_SYS_MBYTES_SDRAM 256 #define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */ -#define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */ -#define CONFIG_DDR_ECC 1 /* enable ECC */ -#define CONFIG_SYS_POST_ECC_ON CONFIG_SYS_POST_ECC +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#define CONFIG_DDR_ECC /* enable ECC */ /* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_ECC_ON | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_FPU | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_OCM | \ - CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_SPR | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_SYSMON | \ - CONFIG_SYS_POST_WATCHDOG | \ - CONFIG_SYS_POST_DSP | \ - CONFIG_SYS_POST_BSPEC1 | \ - CONFIG_SYS_POST_BSPEC2 | \ - CONFIG_SYS_POST_BSPEC3 | \ - CONFIG_SYS_POST_BSPEC4 | \ +#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_ECC | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_FPU | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_OCM | \ + CONFIG_SYS_POST_RTC | \ + CONFIG_SYS_POST_SPR | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_SYSMON | \ + CONFIG_SYS_POST_WATCHDOG | \ + CONFIG_SYS_POST_DSP | \ + CONFIG_SYS_POST_BSPEC1 | \ + CONFIG_SYS_POST_BSPEC2 | \ + CONFIG_SYS_POST_BSPEC3 | \ + CONFIG_SYS_POST_BSPEC4 | \ CONFIG_SYS_POST_BSPEC5) -#define CONFIG_POST_WATCHDOG {\ +/* Define here the base-addresses of the UARTs to test in POST */ +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } + +#define CONFIG_POST_WATCHDOG { \ "Watchdog timer test", \ "watchdog", \ "This test checks the watchdog timer.", \ @@ -188,10 +196,10 @@ &lwmon5_watchdog_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_WATCHDOG \ + CONFIG_SYS_POST_WATCHDOG \ } -#define CONFIG_POST_BSPEC1 {\ +#define CONFIG_POST_BSPEC1 { \ "dsPIC init test", \ "dspic_init", \ "This test returns result of dsPIC READY test run earlier.", \ @@ -199,10 +207,10 @@ &dspic_init_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC1 \ + CONFIG_SYS_POST_BSPEC1 \ } -#define CONFIG_POST_BSPEC2 {\ +#define CONFIG_POST_BSPEC2 { \ "dsPIC test", \ "dspic", \ "This test gets result of dsPIC POST and dsPIC version.", \ @@ -210,32 +218,32 @@ &dspic_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC2 \ + CONFIG_SYS_POST_BSPEC2 \ } -#define CONFIG_POST_BSPEC3 {\ +#define CONFIG_POST_BSPEC3 { \ "FPGA test", \ "fpga", \ "This test checks FPGA registers and memory.", \ - POST_RAM | POST_ALWAYS, \ + POST_RAM | POST_ALWAYS | POST_MANUAL, \ &fpga_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC3 \ + CONFIG_SYS_POST_BSPEC3 \ } -#define CONFIG_POST_BSPEC4 {\ +#define CONFIG_POST_BSPEC4 { \ "GDC test", \ "gdc", \ "This test checks GDC registers and memory.", \ - POST_RAM | POST_ALWAYS, \ + POST_RAM | POST_ALWAYS | POST_MANUAL,\ &gdc_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC4 \ + CONFIG_SYS_POST_BSPEC4 \ } -#define CONFIG_POST_BSPEC5 {\ +#define CONFIG_POST_BSPEC5 { \ "SYSMON1 test", \ "sysmon1", \ "This test checks GPIO_62_EPX pin indicating power failure.", \ @@ -243,7 +251,7 @@ &sysmon1_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC5 \ + CONFIG_SYS_POST_BSPEC5 \ } #define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ @@ -253,34 +261,53 @@ #define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE) #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -/*----------------------------------------------------------------------- +/* * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* RTC */ +#define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52 /* EEPROM (CPU Modul) */ +#define CONFIG_SYS_I2C_EEPROM_MB_ADDR 0x53 /* EEPROM AT24C128 (MainBoard) */ +#define CONFIG_SYS_I2C_DSPIC_ADDR 0x54 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_2_ADDR 0x55 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_KEYB_ADDR 0x56 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* dsPIC */ + #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ /* 64 byte page write mode using*/ /* last 6 bits of the address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE + +#define CONFIG_RTC_PCF8563 /* enable Philips PCF8563 RTC */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ + +#define I2C_ADDR_LIST { \ + CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_EEPROM_CPU_ADDR, \ + CONFIG_SYS_I2C_EEPROM_MB_ADDR, \ + CONFIG_SYS_I2C_DSPIC_ADDR, \ + CONFIG_SYS_I2C_DSPIC_2_ADDR, \ + CONFIG_SYS_I2C_DSPIC_KEYB_ADDR, \ + CONFIG_SYS_I2C_DSPIC_IO_ADDR } -#define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ -#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ -#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +/* Update size in "reg" property of NOR FLASH device tree nodes */ +#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE #define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ -#if 0 -#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ -#define CONFIG_AUTOBOOT_PROMPT \ - "\nEnter password - autoboot in %d sec...\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ -#endif #define CONFIG_PREBOOT "setenv bootdelay 15" @@ -314,15 +341,11 @@ "cp.b 200000 FFF80000 80000\0" \ "upd=run load update\0" \ "lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \ - "source 200000\0" \ + "autoscr 200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ @@ -410,9 +433,9 @@ #define CONFIG_CMD_USB #endif -/*----------------------------------------------------------------------- +/* * Miscellaneous configurable options - *----------------------------------------------------------------------*/ + */ #define CONFIG_SUPPORT_VFAT #define CONFIG_SYS_LONGHELP /* undef to save memory */ @@ -445,9 +468,9 @@ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -/*----------------------------------------------------------------------- +/* * PCI stuff - *----------------------------------------------------------------------*/ + */ /* General PCI */ #define CONFIG_PCI /* include pci support */ #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ @@ -461,29 +484,32 @@ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#ifndef DEBUG #define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */ +#endif #define CONFIG_WD_PERIOD 40000 /* in usec */ #define CONFIG_WD_MAX_RATE 66600 /* in ticks */ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the 40x Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ -/*----------------------------------------------------------------------- +/* * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ + */ #define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x03050200 +#define CONFIG_SYS_EBC_PB0AP 0x03000280 #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000) /* Memory Bank 1 (Lime) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x01004380 -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xdc000) +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xbc000) /* Memory Bank 2 (FPGA) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x01004400 @@ -495,19 +521,27 @@ #define CONFIG_SYS_EBC_CFG 0xb8400000 -/*----------------------------------------------------------------------- +/* * Graphics (Fujitsu Lime) - *----------------------------------------------------------------------*/ + */ +/* SDRAM Clock frequency adjustment register */ +#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038 +#if 1 /* 133MHz is not tested enough, use 100MHz for now */ /* Lime Clock frequency is to set 100MHz */ #define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000 -#if 0 +#else /* Lime Clock frequency for 133MHz */ #define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000 #endif -/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars - and pixel flare on display when 133MHz was configured. According to - SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */ +/* SDRAM Parameter register */ +#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC +/* + * SDRAM parameter value; was 0x414FB7F2, caused several vertical bars + * and pixel flare on display when 133MHz was configured. According to + * SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed + * Grade + */ #ifdef CONFIG_SYS_LIME_CLOCK_133MHZ #define CONFIG_SYS_MB862xx_MMR 0x414FB7F3 #define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ @@ -516,13 +550,15 @@ #define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ #endif -/*----------------------------------------------------------------------- +/* * GPIO Setup - *----------------------------------------------------------------------*/ + */ #define CONFIG_SYS_GPIO_PHY1_RST 12 #define CONFIG_SYS_GPIO_FLASH_WP 14 #define CONFIG_SYS_GPIO_PHY0_RST 22 #define CONFIG_SYS_GPIO_DSPIC_READY 51 +#define CONFIG_SYS_GPIO_CAN_ENABLE 53 +#define CONFIG_SYS_GPIO_LSB_ENABLE 54 #define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55 #define CONFIG_SYS_GPIO_HIGHSIDE 56 #define CONFIG_SYS_GPIO_EEPROM_INT_WP 57 @@ -532,7 +568,7 @@ #define CONFIG_SYS_GPIO_SYSMON_STATUS 62 #define CONFIG_SYS_GPIO_WATCHDOG 63 -/*----------------------------------------------------------------------- +/* * PPC440 GPIO Configuration */ #define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 905c719..80163d4 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -264,7 +264,8 @@ CONFIG_SYS_POST_UART) /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } #define CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ diff --git a/include/configs/manroland/common.h b/include/configs/manroland/common.h index 0224608..291b669 100644 --- a/include/configs/manroland/common.h +++ b/include/configs/manroland/common.h @@ -55,6 +55,11 @@ #define CONFIG_CMD_MII #define CONFIG_CMD_SNTP +/* + * 8-symbol LED display (can be accessed with 'display' command) + */ +#define CONFIG_PDSP188x + #define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ /* diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h index 3e04cfe..8dd87cb 100644 --- a/include/configs/mcu25.h +++ b/include/configs/mcu25.h @@ -192,7 +192,7 @@ CONFIG_SYS_POST_ETHER | \ CONFIG_SYS_POST_SPR) -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #undef CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h index 9b1569a..c30cc4c 100644 --- a/include/configs/microblaze-generic.h +++ b/include/configs/microblaze-generic.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007-2008 Michal Simek + * (C) Copyright 2007-2010 Michal Simek * * Michal SIMEK <monstr@monstr.eu> * @@ -27,31 +27,33 @@ #include "../board/xilinx/microblaze-generic/xparameters.h" -#define CONFIG_MICROBLAZE 1 /* MicroBlaze CPU */ +/* MicroBlaze CPU */ +#define CONFIG_MICROBLAZE 1 #define MICROBLAZE_V5 1 /* uart */ #ifdef XILINX_UARTLITE_BASEADDR - #define CONFIG_XILINX_UARTLITE - #define CONFIG_SERIAL_BASE XILINX_UARTLITE_BASEADDR - #define CONFIG_BAUDRATE XILINX_UARTLITE_BAUDRATE - #define CONFIG_SYS_BAUDRATE_TABLE { CONFIG_BAUDRATE } - #define CONSOLE_ARG "console=console=ttyUL0,115200\0" +# define CONFIG_XILINX_UARTLITE +# define CONFIG_SERIAL_BASE XILINX_UARTLITE_BASEADDR +# define CONFIG_BAUDRATE XILINX_UARTLITE_BAUDRATE +# define CONFIG_SYS_BAUDRATE_TABLE { CONFIG_BAUDRATE } +# define CONSOLE_ARG "console=console=ttyUL0,115200\0" #elif XILINX_UART16550_BASEADDR - #define CONFIG_SYS_NS16550 1 - #define CONFIG_SYS_NS16550_SERIAL - #define CONFIG_SYS_NS16550_REG_SIZE -4 - #define CONFIG_CONS_INDEX 1 - #define CONFIG_SYS_NS16550_COM1 (XILINX_UART16550_BASEADDR + 0x1000 + 0x3) - #define CONFIG_SYS_NS16550_CLK XILINX_UART16550_CLOCK_HZ - #define CONFIG_BAUDRATE 115200 - - /* The following table includes the supported baudrates */ - #define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - #define CONSOLE_ARG "console=console=ttyS0,115200\0" +# define CONFIG_SYS_NS16550 1 +# define CONFIG_SYS_NS16550_SERIAL +# define CONFIG_SYS_NS16550_REG_SIZE -4 +# define CONFIG_CONS_INDEX 1 +# define CONFIG_SYS_NS16550_COM1 \ + (XILINX_UART16550_BASEADDR + 0x1000 + 0x3) +# define CONFIG_SYS_NS16550_CLK XILINX_UART16550_CLOCK_HZ +# define CONFIG_BAUDRATE 115200 + +/* The following table includes the supported baudrates */ +# define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} +# define CONSOLE_ARG "console=console=ttyS0,115200\0" #else - #error Undefined uart +# error Undefined uart #endif /* setting reset address */ @@ -59,41 +61,41 @@ /* ethernet */ #ifdef XILINX_EMACLITE_BASEADDR - #define CONFIG_XILINX_EMACLITE 1 - #define CONFIG_SYS_ENET +# define CONFIG_XILINX_EMACLITE 1 +# define CONFIG_SYS_ENET #elif XILINX_LLTEMAC_BASEADDR - #define CONFIG_XILINX_LL_TEMAC 1 - #define CONFIG_SYS_ENET +# define CONFIG_XILINX_LL_TEMAC 1 +# define CONFIG_SYS_ENET #endif #undef ET_DEBUG /* gpio */ #ifdef XILINX_GPIO_BASEADDR - #define CONFIG_SYS_GPIO_0 1 - #define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR +# define CONFIG_SYS_GPIO_0 1 +# define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR #endif /* interrupt controller */ #ifdef XILINX_INTC_BASEADDR - #define CONFIG_SYS_INTC_0 1 - #define CONFIG_SYS_INTC_0_ADDR XILINX_INTC_BASEADDR - #define CONFIG_SYS_INTC_0_NUM XILINX_INTC_NUM_INTR_INPUTS +# define CONFIG_SYS_INTC_0 1 +# define CONFIG_SYS_INTC_0_ADDR XILINX_INTC_BASEADDR +# define CONFIG_SYS_INTC_0_NUM XILINX_INTC_NUM_INTR_INPUTS #endif /* timer */ #ifdef XILINX_TIMER_BASEADDR - #if (XILINX_TIMER_IRQ != -1) - #define CONFIG_SYS_TIMER_0 1 - #define CONFIG_SYS_TIMER_0_ADDR XILINX_TIMER_BASEADDR - #define CONFIG_SYS_TIMER_0_IRQ XILINX_TIMER_IRQ - #define FREQUENCE XILINX_CLOCK_FREQ - #define CONFIG_SYS_TIMER_0_PRELOAD ( FREQUENCE/1000 ) - #endif +# if (XILINX_TIMER_IRQ != -1) +# define CONFIG_SYS_TIMER_0 1 +# define CONFIG_SYS_TIMER_0_ADDR XILINX_TIMER_BASEADDR +# define CONFIG_SYS_TIMER_0_IRQ XILINX_TIMER_IRQ +# define FREQUENCE XILINX_CLOCK_FREQ +# define CONFIG_SYS_TIMER_0_PRELOAD ( FREQUENCE/1000 ) +# endif #elif XILINX_CLOCK_FREQ - #define CONFIG_XILINX_CLOCK_FREQ XILINX_CLOCK_FREQ +# define CONFIG_XILINX_CLOCK_FREQ XILINX_CLOCK_FREQ #else - #error BAD CLOCK FREQ +# error BAD CLOCK FREQ #endif /* FSL */ /* #define CONFIG_SYS_FSL_2 */ @@ -135,15 +137,20 @@ /* global pointer */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size of global data */ /* start of global data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_SDRAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_SDRAM_SIZE \ + - CONFIG_SYS_GBL_DATA_SIZE) /* monitor code */ -#define SIZE 0x40000 +#define SIZE 0x40000 #define CONFIG_SYS_MONITOR_LEN (SIZE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_MONITOR_END (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_SYS_MONITOR_BASE \ + (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_MONITOR_LEN) +#define CONFIG_SYS_MONITOR_END \ + (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_SYS_MALLOC_LEN SIZE -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_MALLOC_BASE \ + (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) /* stack */ #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_MALLOC_BASE @@ -152,55 +159,62 @@ #define FLASH #ifdef FLASH - #define CONFIG_SYS_FLASH_BASE XILINX_FLASH_START - #define CONFIG_SYS_FLASH_SIZE XILINX_FLASH_SIZE - #define CONFIG_SYS_FLASH_CFI 1 - #define CONFIG_FLASH_CFI_DRIVER 1 - #define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* ?empty sector */ - #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ - #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - #define CONFIG_SYS_FLASH_PROTECTION /* hardware flash protection */ - - #ifdef RAMENV - #define CONFIG_ENV_IS_NOWHERE 1 - #define CONFIG_ENV_SIZE 0x1000 - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) - - #else /* !RAMENV */ - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) - #define CONFIG_ENV_SIZE 0x20000 - #endif /* !RAMBOOT */ +# define CONFIG_SYS_FLASH_BASE XILINX_FLASH_START +# define CONFIG_SYS_FLASH_SIZE XILINX_FLASH_SIZE +# define CONFIG_SYS_FLASH_CFI 1 +# define CONFIG_FLASH_CFI_DRIVER 1 +/* ?empty sector */ +# define CONFIG_SYS_FLASH_EMPTY_INFO 1 +/* max number of memory banks */ +# define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* max number of sectors on one chip */ +# define CONFIG_SYS_MAX_FLASH_SECT 512 +/* hardware flash protection */ +# define CONFIG_SYS_FLASH_PROTECTION + +# ifdef RAMENV +# define CONFIG_ENV_IS_NOWHERE 1 +# define CONFIG_ENV_SIZE 0x1000 +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) + +# else /* !RAMENV */ +# define CONFIG_ENV_IS_IN_FLASH 1 +/* 128K(one sector) for env */ +# define CONFIG_ENV_SECT_SIZE 0x20000 +# define CONFIG_ENV_ADDR \ + (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) +# define CONFIG_ENV_SIZE 0x20000 +# endif /* !RAMBOOT */ #else /* !FLASH */ - /* ENV in RAM */ - #define CONFIG_SYS_NO_FLASH 1 - #define CONFIG_ENV_IS_NOWHERE 1 - #define CONFIG_ENV_SIZE 0x1000 - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) - #define CONFIG_SYS_FLASH_PROTECTION /* hardware flash protection */ +/* ENV in RAM */ +# define CONFIG_SYS_NO_FLASH 1 +# define CONFIG_ENV_IS_NOWHERE 1 +# define CONFIG_ENV_SIZE 0x1000 +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) +/* hardware flash protection */ +# define CONFIG_SYS_FLASH_PROTECTION #endif /* !FLASH */ /* system ace */ #ifdef XILINX_SYSACE_BASEADDR - #define CONFIG_SYSTEMACE - /* #define DEBUG_SYSTEMACE */ - #define SYSTEMACE_CONFIG_FPGA - #define CONFIG_SYS_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR - #define CONFIG_SYS_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH - #define CONFIG_DOS_PARTITION +# define CONFIG_SYSTEMACE +/* #define DEBUG_SYSTEMACE */ +# define SYSTEMACE_CONFIG_FPGA +# define CONFIG_SYS_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR +# define CONFIG_SYS_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH +# define CONFIG_DOS_PARTITION #endif #if defined(XILINX_USE_ICACHE) - #define CONFIG_ICACHE +# define CONFIG_ICACHE #else - #undef CONFIG_ICACHE +# undef CONFIG_ICACHE #endif #if defined(XILINX_USE_DCACHE) - #define CONFIG_DCACHE +# define CONFIG_DCACHE #else - #undef CONFIG_DCACHE +# undef CONFIG_DCACHE #endif /* @@ -222,36 +236,39 @@ #define CONFIG_CMD_ECHO #if defined(CONFIG_DCACHE) || defined(CONFIG_ICACHE) - #define CONFIG_CMD_CACHE +# define CONFIG_CMD_CACHE #else - #undef CONFIG_CMD_CACHE +# undef CONFIG_CMD_CACHE #endif #ifndef CONFIG_SYS_ENET - #undef CONFIG_CMD_NET +# undef CONFIG_CMD_NET +# undef CONFIG_NET_MULTI #else - #define CONFIG_CMD_PING +# define CONFIG_CMD_PING +# define CONFIG_CMD_DHCP +# define CONFIG_NET_MULTI #endif #if defined(CONFIG_SYSTEMACE) - #define CONFIG_CMD_EXT2 - #define CONFIG_CMD_FAT +# define CONFIG_CMD_EXT2 +# define CONFIG_CMD_FAT #endif #if defined(FLASH) - #define CONFIG_CMD_ECHO - #define CONFIG_CMD_FLASH - #define CONFIG_CMD_IMLS - #define CONFIG_CMD_JFFS2 - - #if !defined(RAMENV) - #define CONFIG_CMD_SAVEENV - #define CONFIG_CMD_SAVES - #endif +# define CONFIG_CMD_ECHO +# define CONFIG_CMD_FLASH +# define CONFIG_CMD_IMLS +# define CONFIG_CMD_JFFS2 + +# if !defined(RAMENV) +# define CONFIG_CMD_SAVEENV +# define CONFIG_CMD_SAVES +# endif #else - #undef CONFIG_CMD_IMLS - #undef CONFIG_CMD_FLASH - #undef CONFIG_CMD_JFFS2 +# undef CONFIG_CMD_IMLS +# undef CONFIG_CMD_FLASH +# undef CONFIG_CMD_JFFS2 #endif #if defined(CONFIG_CMD_JFFS2) @@ -259,21 +276,26 @@ #define CONFIG_CMD_MTDPARTS /* mtdparts command line support */ #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ #define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=ml401-0" +#define MTDIDS_DEFAULT "nor0=flash-0" /* default mtd partition table */ -#define MTDPARTS_DEFAULT "mtdparts=ml401-0:256k(u-boot),"\ +#define MTDPARTS_DEFAULT "mtdparts=flash-0:256k(u-boot),"\ "256k(env),3m(kernel),1m(romfs),"\ "1m(cramfs),-(jffs2)" #endif /* Miscellaneous configurable options */ #define CONFIG_SYS_PROMPT "U-Boot-mONStR> " -#define CONFIG_SYS_CBSIZE 512 /* size of console buffer */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* print buffer size */ -#define CONFIG_SYS_MAXARGS 15 /* max number of command args */ +/* size of console buffer */ +#define CONFIG_SYS_CBSIZE 512 + /* print buffer size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 15 #define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_LOAD_ADDR XILINX_RAM_START /* default load address */ +/* default load address */ +#define CONFIG_SYS_LOAD_ADDR XILINX_RAM_START #define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ #define CONFIG_BOOTARGS "root=romfs" @@ -290,9 +312,9 @@ #define CONFIG_PREBOOT "echo U-BOOT for ${hostname};setenv preboot;echo" -#define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" /* hardware flash protection */\ - "nor0=ml401-0\0"\ - "mtdparts=mtdparts=ml401-0:"\ +#define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" \ + "nor0=flash-0\0"\ + "mtdparts=mtdparts=flash-0:"\ "256k(u-boot),256k(env),3m(kernel),"\ "1m(romfs),1m(cramfs),-(jffs2)\0" @@ -301,7 +323,7 @@ /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER #ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +# define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #endif /* __CONFIG_H */ diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h new file mode 100644 index 0000000..bdcebd3 --- /dev/null +++ b/include/configs/mv-common.h @@ -0,0 +1,230 @@ +/* + * (C) Copyright 2010 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +/* + * This file contains Marvell Board Specific common defincations. + * This file should be included in board config header file. + * + * It supports common definations for Kirkwood platform + * TBD: support for Orion5X platforms + */ + +#ifndef _MV_COMMON_H +#define _MV_COMMON_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_MARVELL 1 +#define CONFIG_ARM926EJS 1 /* Basic Architecture */ + +#if defined(CONFIG_KIRKWOOD) +#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ +#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ +#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ + +#define CONFIG_I2C_MVTWSI_BASE KW_TWSI_BASE +#define MV_UART0_BASE KW_UART0_BASE +#define MV_SATA_BASE KW_SATA_BASE +#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET +#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET + +#else +#error "Unsupported SoC" +#endif + +/* additions for new ARM relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +/* Kirkwood has 2k of Security SRAM, use it for SP */ +#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 + +/* + * CLKs configurations + */ +#define CONFIG_SYS_HZ 1000 + +/* + * NS16550 Configuration + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK +#define CONFIG_SYS_NS16550_COM1 MV_UART0_BASE + +/* + * Serial Port configuration + * The following definitions let you select what serial you want to use + * for your console driver. + */ + +#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ + 115200,230400, 460800, 921600 } +/* auto boot */ +#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ +#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ + +#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ + +/* + * NAND configuration + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_KIRKWOOD +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */ +#define NAND_ALLOW_ERASE_ALL 1 +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +#endif + +/* + * SPI Flash configuration + */ +#ifdef CONFIG_CMD_SF +#define CONFIG_SPI_FLASH 1 +#define CONFIG_HARD_SPI 1 +#define CONFIG_KIRKWOOD_SPI 1 +#define CONFIG_SPI_FLASH_MACRONIX 1 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ +#endif + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * Other required minimal configurations + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ +#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ +#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ +#define CONFIG_NR_DRAM_BANKS 4 +#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ +#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ +#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ +#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_NET_MULTI /* specify more that one ports available */ +#define CONFIG_MII /* expose smi ove miiphy interface */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ +#endif /* CONFIG_CMD_NET */ + +/* + * USB/EHCI + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_KIRKWOOD +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_SUPPORT_VFAT +#endif /* CONFIG_CMD_USB */ + +/* + * IDE Support on SATA ports + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_CMD_EXT2 +#define CONFIG_MVSATA_IDE +#define CONFIG_IDE_PREINIT +#define CONFIG_MVSATA_IDE_USE_PORT1 +/* Needs byte-swapping for ATA data register */ +#define CONFIG_IDE_SWAP_IO +/* Data, registers and alternate blocks are at the same offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) +#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) +/* Each 8-bit ATA register is aligned to a 4-bytes address */ +#define CONFIG_SYS_ATA_STRIDE 4 +/* Controller supports 48-bits LBA addressing */ +#define CONFIG_LBA48 +/* CONFIG_CMD_IDE requires some #defines for ATA registers */ +#define CONFIG_SYS_IDE_MAXBUS 2 +#define CONFIG_SYS_IDE_MAXDEVICE 2 +/* ATA registers base is at SATA controller base */ +#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE +#endif /* CONFIG_CMD_IDE */ + +/* + * I2C related stuff + */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_I2C_MVTWSI +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 +#endif + +/* + * File system + */ +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_RBTREE +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_LZO + +#endif /* _MV_COMMON_H */ diff --git a/include/configs/mv88f6281gtw_ge.h b/include/configs/mv88f6281gtw_ge.h index 9ef03a6..d323829 100644 --- a/include/configs/mv88f6281gtw_ge.h +++ b/include/configs/mv88f6281gtw_ge.h @@ -33,66 +33,19 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ /* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ -/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include <config_cmd_default.h> -#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING #define CONFIG_CMD_ENV #define CONFIG_CMD_FAT #define CONFIG_CMD_PING @@ -100,17 +53,18 @@ #define CONFIG_CMD_USB /* - * Flash configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_SF -#define CONFIG_SPI_FLASH 1 -#define CONFIG_HARD_SPI 1 -#define CONFIG_KIRKWOOD_SPI 1 -#define CONFIG_SPI_FLASH_MACRONIX 1 -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ -#endif +#include "mv-common.h" + +/* Unwanted stuffs from mv-common.h */ +#undef CONFIG_CMD_EXT2 +#undef CONFIG_CMD_JFFS2 +#undef CONFIG_CMD_FAT +#undef CONFIG_CMD_UBI +#undef CONFIG_CMD_UBIFS +#undef CONFIG_RBTREE /* * Environment variables configurations @@ -142,59 +96,11 @@ "x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#endif /* CONFIG_CMD_NET */ - -/* - * Marvell 88Exxxx Switch configurations - */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init phy/swtich */ #define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */ - -/* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#endif /* CONFIG_CMD_NET */ #endif /* _CONFIG_MV88F6281GTW_GE_H */ diff --git a/include/configs/omap1510.h b/include/configs/omap1510.h index 931560c..e6d9c7a 100644 --- a/include/configs/omap1510.h +++ b/include/configs/omap1510.h @@ -28,7 +28,7 @@ * 675 Mass Ave, Cambridge, MA 02139, USA. */ -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /* There are 2 sets of general I/O --> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 2463be4..1bd0f37 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -340,8 +340,7 @@ extern unsigned int boot_flash_sec; extern unsigned int boot_flash_type; #endif -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/omap730.h b/include/configs/omap730.h index 04d5144..c7682a1 100644 --- a/include/configs/omap730.h +++ b/include/configs/omap730.h @@ -31,7 +31,7 @@ #ifndef __INCLUDED_OMAP730_H #define __INCLUDED_OMAP730_H -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /*************************************************************************** * OMAP730 Configuration Registers diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index 846dfcd..cfdd09c 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -38,59 +38,12 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_OPENRD_BASE /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ @@ -106,15 +59,10 @@ #define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -154,97 +102,19 @@ "mtdparts="MTDPARTS_DEFAULT"\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0x8 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - -/* - * IDe Support on SATA port0 - */ -#ifdef CONFIG_CMD_IDE -#define __io -#define CONFIG_CMD_EXT2 -#define CONFIG_MVSATA_IDE -#define CONFIG_IDE_PREINIT -#define CONFIG_MVSATA_IDE_USE_PORT1 -/* Needs byte-swapping for ATA data register */ -#define CONFIG_IDE_SWAP_IO -/* Data, registers and alternate blocks are at the same offset */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) -#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) -#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) -/* Each 8-bit ATA register is aligned to a 4-bytes address */ -#define CONFIG_SYS_ATA_STRIDE 4 -/* Controller supports 48-bits LBA addressing */ -#define CONFIG_LBA48 -/* CONFIG_CMD_IDE requires some #defines for ATA registers */ -#define CONFIG_SYS_IDE_MAXBUS 2 -#define CONFIG_SYS_IDE_MAXDEVICE 2 -/* ATA registers base is at SATA controller base */ -#define CONFIG_SYS_ATA_BASE_ADDR KW_SATA_BASE -/* ATA bus 0 is Kirkwood port 0 on openrd */ -#define CONFIG_SYS_ATA_IDE0_OFFSET KW_SATA_PORT0_OFFSET -/* ATA bus 1 is Kirkwood port 1 on openrd */ -#define CONFIG_SYS_ATA_IDE1_OFFSET KW_SATA_PORT1_OFFSET -#endif /* CONFIG_CMD_IDE */ - -/* - * File system + * SATA Driver configuration */ -#define CONFIG_CMD_FAT -#define CONFIG_CMD_UBI -#define CONFIG_CMD_UBIFS -#define CONFIG_RBTREE -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_MTD_PARTITIONS -#define CONFIG_CMD_MTDPARTS -#define CONFIG_LZO +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #endif /* _CONFIG_OPENRD_BASE_H */ diff --git a/include/configs/pcu_e.h b/include/configs/pcu_e.h deleted file mode 100644 index 3aee206..0000000 --- a/include/configs/pcu_e.h +++ /dev/null @@ -1,550 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Workaround for layout bug on prototype board - */ -#define PCU_E_WITH_SWAPPED_CS 1 - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC860 1 /* This is a MPC860T CPU */ -#define CONFIG_MPC860T 1 -#define CONFIG_PCU_E 1 /* ...on a PCU E board */ - -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ - -#define CONFIG_BAUDRATE 9600 -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ - -#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */ - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - -#define CONFIG_SPI /* enable SPI driver */ -#define CONFIG_SPI_X /* 16 bit EEPROM addressing */ - -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - - -/* ---------------------------------------------------------------- - * Offset to initial SPI buffers in DPRAM (used if the environment - * is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to - * use at an early stage. It is used between the two initialization - * calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it - * far enough from the start of the data area (as well as from the - * stack pointer). - * ---------------------------------------------------------------- */ -#define CONFIG_SYS_SPI_INIT_OFFSET 0xB00 - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ - -/* Ethernet hardware configuration done using port pins */ -#define CONFIG_SYS_PB_ETH_RESET 0x00000020 /* PB 26 */ -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_PA_ETH_MDDIS 0x4000 /* PA 1 */ -#define CONFIG_SYS_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */ -#define CONFIG_SYS_PB_ETH_CFG1 0x00000400 /* PB 21 */ -#define CONFIG_SYS_PB_ETH_CFG2 0x00000200 /* PB 22 */ -#define CONFIG_SYS_PB_ETH_CFG3 0x00000100 /* PB 23 */ -#else /* XXX */ -#define CONFIG_SYS_PB_ETH_MDDIS 0x00000010 /* PB 27 */ -#define CONFIG_SYS_PB_ETH_POWERDOWN 0x00000100 /* PB 23 */ -#define CONFIG_SYS_PB_ETH_CFG1 0x00000200 /* PB 22 */ -#define CONFIG_SYS_PB_ETH_CFG2 0x00000400 /* PB 21 */ -#define CONFIG_SYS_PB_ETH_CFG3 0x00000800 /* PB 20 */ -#endif /* XXX */ - -/* Ethernet settings: - * MDIO enabled, autonegotiation, 10/100Mbps, half/full duplex - */ -#define CONFIG_SYS_ETH_MDDIS_VALUE 0 -#define CONFIG_SYS_ETH_CFG1_VALUE 1 -#define CONFIG_SYS_ETH_CFG2_VALUE 1 -#define CONFIG_SYS_ETH_CFG3_VALUE 1 - -/* PUMA configuration */ -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_PB_PUMA_PROG 0x00000010 /* PB 27 */ -#else /* XXX */ -#define CONFIG_SYS_PA_PUMA_PROG 0x4000 /* PA 1 */ -#endif /* XXX */ -#define CONFIG_SYS_PC_PUMA_DONE 0x0008 /* PC 12 */ -#define CONFIG_SYS_PC_PUMA_INIT 0x0004 /* PC 13 */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFE000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Address accessed to reset the board - must not be mapped/assigned - */ -#define CONFIG_SYS_RESET_ADDRESS 0xFEFFFFFF - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* this is an ugly hack needed because of the silly non-constant address map */ -#define CONFIG_SYS_FLASH_BASE (0-flash_info[0].size-flash_info[1].size) - -#if defined(DEBUG) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 160 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ - -#if 0 -/* Start port with environment in flash; switch to SPI EEPROM later */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment */ -#define CONFIG_ENV_ADDR 0xFFFFE000 /* Address of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x2000 /* use the top-most 8k boot sector */ -#else -/* Final version: environment in EEPROM */ -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_ENV_OFFSET 1024 -#define CONFIG_ENV_SIZE 1024 -#endif - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#define CONFIG_SYS_DELAYED_ICACHE 1 /* enable ICache not before - * running in RAM. - */ - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * External Arbitration max. priority (7), - * Debug pins configuration '11', - * Asynchronous external master enable. - */ -/* => 0x70600200 */ -#define CONFIG_SYS_SIUMCR (SIUMCR_EARP7 | SIUMCR_DBGC11 | SIUMCR_AEME) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit, set PLL multiplication factor ! - */ -/* 0x00004080 */ -#define CONFIG_SYS_PLPRCR_MF 0 /* (0+1) * 50 = 50 MHz Clock */ -#define CONFIG_SYS_PLPRCR \ - ( (CONFIG_SYS_PLPRCR_MF << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ - /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ - PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \ - ) - -#define CONFIG_8xx_GCLK_FREQ ((CONFIG_SYS_PLPRCR_MF+1)*50000000) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - * - * Note: PITRTCLK is 50MHz / 512 = 97'656.25 Hz - */ -#define SCCR_MASK SCCR_EBDF11 -/* 0x01800000 */ -#define CONFIG_SYS_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \ - SCCR_RTDIV | SCCR_RTSEL | \ - /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ - SCCR_EBDF00 | SCCR_DFSYNC00 | \ - SCCR_DFBRG00 | SCCR_DFNL000 | \ - SCCR_DFNH000 | SCCR_DFLCD100 | \ - SCCR_DFALCD01) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - * - * Note: RTC counts at PITRTCLK / 8'192 = 11.920928 Hz !!! - * - * Don't expect the "date" command to work without a 32kHz clock input! - */ -/* 0x00C3 => 0x0003 */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration Register 19-4 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0x0000 - -/*----------------------------------------------------------------------- - * RMDS - RISC Microcode Development Support Control Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMDS 0 - -/*----------------------------------------------------------------------- - * - * Interrupt Levels - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - second Flash bank optional - */ - -#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */ -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define FLASH_BASE6_PRELIM 0xFF000000 /* FLASH bank #1 */ -#else /* XXX */ -#define FLASH_BASE1_PRELIM 0xFF000000 /* FLASH bank #1 */ -#endif /* XXX */ - -/* - * used to re-map FLASH: restrict access enough but not too much to - * meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ - -/* FLASH timing: CSNT = 0, ACS = 00, SCY = 8, EHTR = 1 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_EHTR) - -#define CONFIG_SYS_OR0_REMAP ( CONFIG_SYS_REMAP_OR_AM | OR_ACS_DIV1 | OR_BI | \ - CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \ - CONFIG_SYS_OR_TIMING_FLASH) -/* 16 bit, bank valid */ -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) - -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_OR6_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR0_PRELIM -#define CONFIG_SYS_BR6_PRELIM ((FLASH_BASE6_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) -#else /* XXX */ -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM -#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) -#endif /* XXX */ - -/* - * BR2/OR2: SDRAM - * - * Multiplexed addresses, GPL5 output to GPL5_A (don't care) - */ -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define SDRAM_BASE5_PRELIM 0x00000000 /* SDRAM bank */ -#else /* XXX */ -#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank */ -#endif /* XXX */ -#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map 128 MB (>SDRAM_MAX_SIZE!) */ -#define SDRAM_TIMING OR_CSNT_SAM /* SDRAM-Timing */ - -#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ - -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_OR5_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) -#define CONFIG_SYS_BR5_PRELIM ((SDRAM_BASE5_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) -#else /* XXX */ -#define CONFIG_SYS_OR2_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) -#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) -#endif /* XXX */ - -/* - * BR3/OR3: CAN Controller - * BR3: 0x10000401 OR3: 0xffff818a - */ -#define CAN_CTRLR_BASE 0x10000000 /* CAN Controller */ -#define CAN_CTRLR_OR_AM 0xFFFF8000 /* 32 kB */ -#define CAN_CTRLR_TIMING (OR_BI | OR_SCY_8_CLK | OR_SETA | OR_EHTR) - -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_BR4_PRELIM ((CAN_CTRLR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR4_PRELIM (CAN_CTRLR_OR_AM | CAN_CTRLR_TIMING) -#else /* XXX */ -#define CONFIG_SYS_BR3_PRELIM ((CAN_CTRLR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR3_PRELIM (CAN_CTRLR_OR_AM | CAN_CTRLR_TIMING) -#endif /* XXX */ - -/* - * BR4/OR4: PUMA Config - * - * Memory controller will be used in 2 modes: - * - * - "read" mode: - * BR4: 0x10100801 OR4: 0xffff8530 - * - "load" mode (chip select on UPM B): - * BR4: 0x101008c1 OR4: 0xffff8630 - * - * Default initialization is in "read" mode - */ -#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */ -#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */ -#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 | OR_SCY_3_CLK) -#define PUMA_CONF_READ_TIMING (OR_G5LA | OR_BI | OR_SCY_3_CLK) - -#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) | \ - BR_PS_16 | BR_MS_UPMB | BR_V) -#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING) - -#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING) - -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_BR3_PRELIM PUMA_CONF_BR_READ -#define CONFIG_SYS_OR3_PRELIM PUMA_CONF_OR_READ -#else /* XXX */ -#define CONFIG_SYS_BR4_PRELIM PUMA_CONF_BR_READ -#define CONFIG_SYS_OR4_PRELIM PUMA_CONF_OR_READ -#endif /* XXX */ - -/* - * BR5/OR5: PUMA: SMA Bus 8 Bit - * BR5: 0x10200401 OR5: 0xffe0010a - */ -#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */ -#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */ -#define PUMA_SMA8_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) - -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_BR2_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR2_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) -#else /* XXX */ -#define CONFIG_SYS_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) -#endif /* XXX */ - -/* - * BR6/OR6: PUMA: SMA Bus 16 Bit - * BR6: 0x10600801 OR6: 0xffe0010a - */ -#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */ -#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */ -#define PUMA_SMA16_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) - -#if PCU_E_WITH_SWAPPED_CS /* XXX */ -#define CONFIG_SYS_BR1_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR1_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) -#else /* XXX */ -#define CONFIG_SYS_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) -#endif /* XXX */ - -/* - * BR7/OR7: PUMA: external Flash - * BR7: 0x10a00801 OR7: 0xfe00010a - */ -#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */ -#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */ -#define PUMA_FLASH_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) - -#define CONFIG_SYS_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA) - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MPTPR 0x0200 - -/* - * MAMR settings for SDRAM - * 0x30104118 = Timer A period 0x30, MAMR_AMB_TYPE_1, MAMR_G0CLB_A10, - * MAMR_RLFB_1X, MAMR_WLFB_1X, MAMR_TLFB_8X - * 0x30904114 = - " - | Periodic Timer A Enable, MAMR_TLFB_4X - */ -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 0x30 /* = 48 */ - -#define CONFIG_SYS_MAMR ( (CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | \ - MAMR_AMA_TYPE_1 | \ - MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | \ - MAMR_WLFA_1X | \ - MAMR_TLFA_8X ) - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/qong.h b/include/configs/qong.h index b1aca93..f26ced1 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -301,8 +301,7 @@ extern int qong_nand_rdy(void *chip); "mtdparts=physmap-flash.0:384k(U-Boot),128k(env1)," \ "128k(env2),2432k(kernel),13m(ramdisk),-(user)" -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x80000000 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR #define CONFIG_SYS_INIT_RAM_END IRAM_SIZE diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h index 5857301..60f9579 100644 --- a/include/configs/rd6281a.h +++ b/include/configs/rd6281a.h @@ -33,59 +33,13 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_RD6281A /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ /* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ -/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ @@ -97,17 +51,13 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -143,56 +93,23 @@ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_MV88E61XX_MULTICHIP_ADRMODE #define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */ #define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */ #define CONFIG_PHY_BASE_ADR 0x0A -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init switch and PHY */ #define CONFIG_MV88E61XX_SWITCH /* Enable MV88E61XX switch driver */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #endif /* _CONFIG_RD6281A_H */ diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index c5de86e..83dd8ff 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -33,82 +33,28 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_SHEEVAPLUG /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include <config_cmd_default.h> -#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB - /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -144,58 +90,14 @@ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1 MiB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - -/* * File system */ #define CONFIG_CMD_EXT2 diff --git a/include/configs/tcm-bf518.h b/include/configs/tcm-bf518.h index 52055e8..042d789 100644 --- a/include/configs/tcm-bf518.h +++ b/include/configs/tcm-bf518.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf518-0.0 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA diff --git a/include/configs/tcm-bf537.h b/include/configs/tcm-bf537.h index 24ce8f8..dceff30 100644 --- a/include/configs/tcm-bf537.h +++ b/include/configs/tcm-bf537.h @@ -11,7 +11,6 @@ /* * Processor Settings */ -#define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS diff --git a/include/configs/tx25.h b/include/configs/tx25.h index c798570..bcc8140 100644 --- a/include/configs/tx25.h +++ b/include/configs/tx25.h @@ -176,8 +176,7 @@ "update=nand erase 0 40000;nand write ${loadaddr} 0 40000\0" \ "upd=run load update\0" \ -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/zeus.h b/include/configs/zeus.h index aa250cc..06d4526 100644 --- a/include/configs/zeus.h +++ b/include/configs/zeus.h @@ -94,7 +94,7 @@ #define CONFIG_SYS_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */ /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #define CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ diff --git a/include/fat.h b/include/fat.h index de48afd..afb2116 100644 --- a/include/fat.h +++ b/include/fat.h @@ -30,6 +30,10 @@ #include <asm/byteorder.h> #define CONFIG_SUPPORT_VFAT +/* Maximum Long File Name length supported here is 128 UTF-16 code units */ +#define VFAT_MAXLEN_BYTES 256 /* Maximum LFN buffer in bytes */ +#define VFAT_MAXSEQ 9 /* Up to 9 of 13 2-byte UTF-16 entries */ +#define LINEAR_PREFETCH_SIZE (SECTOR_SIZE*2) /* Prefetch buffer size */ #define SECTOR_SIZE FS_BLOCK_SIZE diff --git a/include/fdt_support.h b/include/fdt_support.h index fd94929..deb5dda 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -87,6 +87,7 @@ u64 fdt_translate_address(void *blob, int node_offset, const u32 *in_addr); int fdt_node_offset_by_compat_reg(void *blob, const char *compat, phys_addr_t compat_off); int fdt_alloc_phandle(void *blob); +int fdt_add_edid(void *blob, const char *compat, unsigned char *buf); #endif /* ifdef CONFIG_OF_LIBFDT */ #endif /* ifndef __FDT_SUPPORT_H */ diff --git a/include/fsl_diu_fb.h b/include/fsl_diu_fb.h new file mode 100644 index 0000000..87443e1 --- /dev/null +++ b/include/fsl_diu_fb.h @@ -0,0 +1,60 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * York Sun <yorksun@freescale.com> + * + * FSL DIU Framebuffer driver + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +struct fb_var_screeninfo { + unsigned int xres; /* visible resolution */ + unsigned int yres; + + unsigned int bits_per_pixel; /* guess what */ + + /* Timing: All values in pixclocks, except pixclock (of course) */ + unsigned int pixclock; /* pixel clock in ps (pico seconds) */ + unsigned int left_margin; /* time from sync to picture */ + unsigned int right_margin; /* time from picture to sync */ + unsigned int upper_margin; /* time from sync to picture */ + unsigned int lower_margin; + unsigned int hsync_len; /* length of horizontal sync */ + unsigned int vsync_len; /* length of vertical sync */ + unsigned int sync; /* see FB_SYNC_* */ + unsigned int vmode; /* see FB_VMODE_* */ + unsigned int rotate; /* angle we rotate counter clockwise */ +}; + +struct fb_info { + struct fb_var_screeninfo var; /* Current var */ + unsigned long smem_start; /* Start of frame buffer mem */ + /* (physical address) */ + unsigned int smem_len; /* Length of frame buffer mem */ + unsigned int type; /* see FB_TYPE_* */ + unsigned int line_length; /* length of a line in bytes */ + + char *screen_base; + unsigned long screen_size; +}; + + +extern char *fsl_fb_open(struct fb_info **info); +int fsl_diu_init(int xres, unsigned int pixel_format, int gamma_fix); +int platform_diu_init(unsigned int *xres, unsigned int *yres); diff --git a/include/lcd.h b/include/lcd.h index cd9d49d..0e098d9 100644 --- a/include/lcd.h +++ b/include/lcd.h @@ -167,6 +167,7 @@ typedef struct vidinfo { u_long vl_sync; /* Horizontal / vertical sync */ u_long vl_bpix; /* Bits per pixel, 0 = 1, 1 = 2, 2 = 4, 3 = 8, 4 = 16 */ u_long vl_tft; /* 0 = passive, 1 = TFT */ + u_long vl_cont_pol_low; /* contrast polarity is low */ /* Horizontal control register. */ u_long vl_hsync_len; /* Length of horizontal sync */ diff --git a/include/led-display.h b/include/led-display.h new file mode 100644 index 0000000..41c3744 --- /dev/null +++ b/include/led-display.h @@ -0,0 +1,36 @@ +/* + * (C) Copyright 2005-2010 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2010 + * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _led_display_h_ +#define _led_display_h_ + +/* Display Commands */ +#define DISPLAY_CLEAR 0x1 /* Clear the display */ +#define DISPLAY_HOME 0x2 /* Set cursor at home position */ +#define DISPLAY_MARK 0x4 /* Enable the decimal point led, if implemented */ + +void display_set(int cmd); +int display_putc(char c); +#endif diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index 16556c4..3b18d7d 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -208,10 +208,6 @@ struct mtd_info { int (*lock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); int (*unlock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); - /* Power Management functions */ - int (*suspend) (struct mtd_info *mtd); - void (*resume) (struct mtd_info *mtd); - /* Bad block management functions */ int (*block_isbad) (struct mtd_info *mtd, loff_t ofs); int (*block_markbad) (struct mtd_info *mtd, loff_t ofs); @@ -259,7 +255,9 @@ extern struct mtd_info *get_mtd_device(struct mtd_info *mtd, int num); extern struct mtd_info *get_mtd_device_nm(const char *name); extern void put_mtd_device(struct mtd_info *mtd); - +extern void mtd_get_len_incl_bad(struct mtd_info *mtd, uint64_t offset, + const uint64_t length, uint64_t *len_incl_bad, + int *truncated); /* XXX U-BOOT XXX */ #if 0 struct mtd_notifier { diff --git a/include/linux/mtd/onenand.h b/include/linux/mtd/onenand.h index 68e174e..5465562 100644 --- a/include/linux/mtd/onenand.h +++ b/include/linux/mtd/onenand.h @@ -154,6 +154,7 @@ struct onenand_chip { /* * OneNAND Flash Manufacturer ID Codes */ +#define ONENAND_MFR_NUMONYX 0x20 #define ONENAND_MFR_SAMSUNG 0xec /** diff --git a/include/mpc5xxx.h b/include/mpc5xxx.h index 2d343c7..859d696 100644 --- a/include/mpc5xxx.h +++ b/include/mpc5xxx.h @@ -160,11 +160,12 @@ #define MPC5XXX_WU_GPIO_DATA_O (MPC5XXX_WU_GPIO + 0x000c) #define MPC5XXX_WU_GPIO_DATA_I (MPC5XXX_WU_GPIO + 0x0020) -/* GPIO pins */ +/* GPIO pins, for Rev.B chip */ #define GPIO_WKUP_7 0x80000000UL #define GPIO_PSC6_0 0x10000000UL #define GPIO_PSC3_9 0x04000000UL #define GPIO_PSC1_4 0x01000000UL +#define GPIO_PSC2_4 0x02000000UL #define MPC5XXX_GPIO_SIMPLE_PSC6_3 0x20000000UL #define MPC5XXX_GPIO_SIMPLE_PSC6_2 0x10000000UL diff --git a/include/nand.h b/include/nand.h index 8bdf419..a452411 100644 --- a/include/nand.h +++ b/include/nand.h @@ -98,13 +98,16 @@ struct nand_read_options { typedef struct nand_read_options nand_read_options_t; struct nand_erase_options { - ulong length; /* number of bytes to erase */ - ulong offset; /* first address in NAND to erase */ + loff_t length; /* number of bytes to erase */ + loff_t offset; /* first address in NAND to erase */ int quiet; /* don't display progress messages */ int jffs2; /* if true: format for jffs2 usage * (write appropriate cleanmarker blocks) */ int scrub; /* if true, really clean NAND by erasing * bad blocks (UNSAFE) */ + + /* Don't include skipped bad blocks in size to be erased */ + int spread; }; typedef struct nand_erase_options nand_erase_options_t; diff --git a/include/netdev.h b/include/netdev.h index 94eedfe..7f66419 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -54,6 +54,8 @@ int designware_initialize(u32 id, ulong base_addr, u32 phy_addr); int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr); int e1000_initialize(bd_t *bis); int eepro100_initialize(bd_t *bis); +int enc28j60_initialize(unsigned int bus, unsigned int cs, + unsigned int max_hz, unsigned int mode); int ep93xx_eth_initialize(u8 dev_num, int base_addr); int ethoc_initialize(u8 dev_num, int base_addr); int eth_3com_initialize (bd_t * bis); @@ -85,9 +87,9 @@ int skge_initialize(bd_t *bis); int smc911x_initialize(u8 dev_num, int base_addr); int smc91111_initialize(u8 dev_num, int base_addr); int tsi108_eth_initialize(bd_t *bis); -int uec_initialize(int index); int uec_standard_init(bd_t *bis); int uli526x_initialize(bd_t *bis); +int xilinx_emaclite_initialize (bd_t *bis, int base_addr); int sh_eth_initialize(bd_t *bis); int dm9000_initialize(bd_t *bis); diff --git a/include/status_led.h b/include/status_led.h index b39ca64..360195c 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -190,22 +190,6 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ -/***** PCU E and CCM ************************************************/ -#elif (defined(CONFIG_PCU_E) || defined(CONFIG_CCM)) - -# define STATUS_LED_PAR im_cpm.cp_pbpar -# define STATUS_LED_DIR im_cpm.cp_pbdir -# define STATUS_LED_ODR im_cpm.cp_pbodr -# define STATUS_LED_DAT im_cpm.cp_pbdat - -# define STATUS_LED_BIT 0x00010000 /* green LED is on PB.15 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - /***** ICU862 ********************************************************/ #elif defined(CONFIG_ICU862) @@ -270,7 +254,7 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ /***** KUP4K, KUP4X ****************************************************/ -#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) || defined(CONFIG_CCM) +#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) # define STATUS_LED_PAR im_ioport.iop_papar # define STATUS_LED_DIR im_ioport.iop_padir |