diff options
Diffstat (limited to 'include')
74 files changed, 2735 insertions, 788 deletions
diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h deleted file mode 100644 index 3920d35..0000000 --- a/include/configs/EP1C20.h +++ /dev/null @@ -1,214 +0,0 @@ -/* - * (C) Copyright 2005, Psyent Corporation <www.psyent.com> - * Scott McNutt <smcnutt@psyent.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*------------------------------------------------------------------------ - * BOARD/CPU - *----------------------------------------------------------------------*/ -#define CONFIG_EP1C20 1 /* EP1C20 board */ -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ - -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */ -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/ - -/*------------------------------------------------------------------------ - * CACHE -- the following will support II/s and II/f. The II/s does not - * have dcache, so the cache instructions will behave as NOPs. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */ -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */ -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ - -/*------------------------------------------------------------------------ - * MEMORY BASE ADDRESSES - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */ -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */ -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */ -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */ -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/ - -/*------------------------------------------------------------------------ - * MEMORY ORGANIZATION - * -Monitor at top. - * -The heap is placed below the monitor. - * -Global data is placed below the heap. - * -The stack is placed below global data (&grows down). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 128k */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET - -/*------------------------------------------------------------------------ - * FLASH (AM29LV065D) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size */ - -/*------------------------------------------------------------------------ - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above - * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the - * reset address, no? This will keep the environment in user region - * of flash. NOTE: the monitor length must be multiple of sector size - * (which is common practice). - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */ -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN) - -/*------------------------------------------------------------------------ - * CONSOLE - *----------------------------------------------------------------------*/ -#define CONFIG_ALTERA_UART 1 /* Use altera uart */ -#if defined(CONFIG_ALTERA_JTAG_UART) -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ -#else -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */ -#endif - -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */ -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ - -/*------------------------------------------------------------------------ - * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for - * epcs device access is enabled. The base address is the epcs - * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK. - * The register base is currently at offset 0x600 from the memory base. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_NIOS_EPCSBASE 0x02100200 /* EPCS register base */ - -/*------------------------------------------------------------------------ - * DEBUG - *----------------------------------------------------------------------*/ -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */ - -/*------------------------------------------------------------------------ - * TIMEBASE -- - * - * The high res timer defaults to 1 msec. Since it includes the period - * registers, the interrupt frequency can be reduced using TMRCNT. - * If the default period is acceptable, TMRCNT can be left undefined. - * TMRMS represents the desired mecs per tick (msecs per interrupt). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_HZ 1000 /* Always 1000 */ -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */ -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/ -#define CONFIG_SYS_NIOS_TMRCNT \ - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) - -/*------------------------------------------------------------------------ - * STATUS LED -- Provides a simple blinking led. For Nios2 each board - * must implement its own led routines -- leds are, after all, - * board-specific, no? - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ -#define CONFIG_STATUS_LED /* Enable status driver */ - -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */ -#define STATUS_LED_STATE 1 /* Blinking */ -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */ - -/*------------------------------------------------------------------------ - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... - * and really doesn't need any additional clutter. So I choose the lazy - * way out to avoid changes there -- define the base address to ensure - * cache bypass so there's no need to monkey with inx/outx macros. - *----------------------------------------------------------------------*/ -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ -#define CONFIG_NET_MULTI -#define CONFIG_SMC91111 /* Using SMC91c111 */ -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ - -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.2.21 -#define CONFIG_SERVERIP 192.168.2.16 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_PING -#define CONFIG_CMD_SAVES - -#undef CONFIG_CMD_BOOTD -#undef CONFIG_CMD_CONSOLE -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_ITEST -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_SETGETDCR -#undef CONFIG_CMD_SOURCE -#undef CONFIG_CMD_XIMG - - -/*------------------------------------------------------------------------ - * MISC - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* Provide extended help*/ -#define CONFIG_SYS_PROMPT "==> " /* Command prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */ -#define CONFIG_SYS_MAXARGS 16 /* Max command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */ -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000 - -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -#endif /* __CONFIG_H */ diff --git a/include/configs/EP1S10.h b/include/configs/EP1S10.h deleted file mode 100644 index bfbf8c1..0000000 --- a/include/configs/EP1S10.h +++ /dev/null @@ -1,207 +0,0 @@ -/* - * (C) Copyright 2005, Psyent Corporation <www.psyent.com> - * Scott McNutt <smcnutt@psyent.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*------------------------------------------------------------------------ - * BOARD/CPU - *----------------------------------------------------------------------*/ -#define CONFIG_EP1S10 1 /* EP1S10 board */ -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ - -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */ -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */ - -/*------------------------------------------------------------------------ - * CACHE -- the following will support II/s and II/f. The II/s does not - * have dcache, so the cache instructions will behave as NOPs. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */ -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */ -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ - -/*------------------------------------------------------------------------ - * MEMORY BASE ADDRESSES - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */ -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */ -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */ -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */ -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB */ - -/*------------------------------------------------------------------------ - * MEMORY ORGANIZATION - * -Monitor at top. - * -The heap is placed below the monitor. - * -Global data is placed below the heap. - * -The stack is placed below global data (&grows down). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256k */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) /* 256k heap */ - -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET - -/*------------------------------------------------------------------------ - * FLASH (AM29LV065D) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ - -/*------------------------------------------------------------------------ - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above - * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom - * of flash memory. This will keep the environment in user region - * of flash. NOTE: the monitor length must be multiple of sector size - * (which is common practice). - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */ -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) - -/*------------------------------------------------------------------------ - * CONSOLE - *----------------------------------------------------------------------*/ -#define CONFIG_ALTERA_UART 1 /* Use altera uart */ -#if defined(CONFIG_ALTERA_JTAG_UART) -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ -#else -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */ -#endif - -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */ -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ - -/*------------------------------------------------------------------------ - * EPCS Device -- None for stratix. - *----------------------------------------------------------------------*/ -#undef CONFIG_SYS_NIOS_EPCSBASE - -/*------------------------------------------------------------------------ - * DEBUG - *----------------------------------------------------------------------*/ -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */ - -/*------------------------------------------------------------------------ - * TIMEBASE -- - * - * The high res timer defaults to 1 msec. Since it includes the period - * registers, the interrupt frequency can be reduced using TMRCNT. - * If the default period is acceptable, TMRCNT can be left undefined. - * TMRMS represents the desired mecs per tick (msecs per interrupt). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_HZ 1000 /* Always 1000 */ -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */ -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/ -#define CONFIG_SYS_NIOS_TMRCNT \ - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) - -/*------------------------------------------------------------------------ - * STATUS LED -- Provides a simple blinking led. For Nios2 each board - * must implement its own led routines -- since leds are board-specific. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ -#define CONFIG_STATUS_LED /* Enable status driver */ - -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */ -#define STATUS_LED_STATE 1 /* Blinking */ -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */ - -/*------------------------------------------------------------------------ - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... - * and really doesn't need any additional clutter. So I choose the lazy - * way out to avoid changes there -- define the base address to ensure - * cache bypass so there's no need to monkey with inx/outx macros. - *----------------------------------------------------------------------*/ -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ -#define CONFIG_NET_MULTI -#define CONFIG_SMC91111 /* Using SMC91c111 */ -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ - -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.2.21 -#define CONFIG_SERVERIP 192.168.2.16 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#define CONFIG_CMD_BDI -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IMI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_LOADS -#define CONFIG_CMD_LOADB -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_MISC -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_RUN -#define CONFIG_CMD_SAVES - - -/*------------------------------------------------------------------------ - * MISC - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* Provide extended help*/ -#define CONFIG_SYS_PROMPT "==> " /* Command prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */ -#define CONFIG_SYS_MAXARGS 16 /* Max command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */ -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000 - -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -#endif /* __CONFIG_H */ diff --git a/include/configs/EP1S40.h b/include/configs/EP1S40.h deleted file mode 100644 index 4d905fe..0000000 --- a/include/configs/EP1S40.h +++ /dev/null @@ -1,207 +0,0 @@ -/* - * (C) Copyright 2005, Psyent Corporation <www.psyent.com> - * Scott McNutt <smcnutt@psyent.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*------------------------------------------------------------------------ - * BOARD/CPU - *----------------------------------------------------------------------*/ -#define CONFIG_EP1S40 1 /* EP1S40 board */ -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ - -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */ -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */ - -/*------------------------------------------------------------------------ - * CACHE -- the following will support II/s and II/f. The II/s does not - * have dcache, so the cache instructions will behave as NOPs. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */ -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */ -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ - -/*------------------------------------------------------------------------ - * MEMORY BASE ADDRESSES - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */ -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */ -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */ -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */ -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB */ - -/*------------------------------------------------------------------------ - * MEMORY ORGANIZATION - * -Monitor at top. - * -The heap is placed below the monitor. - * -Global data is placed below the heap. - * -The stack is placed below global data (&grows down). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256k */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) /* 256k heap */ - -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET - -/*------------------------------------------------------------------------ - * FLASH (AM29LV065D) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ - -/*------------------------------------------------------------------------ - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above - * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom - * of flash memory. This will keep the environment in user region - * of flash. NOTE: the monitor length must be multiple of sector size - * (which is common practice). - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */ -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) - -/*------------------------------------------------------------------------ - * CONSOLE - *----------------------------------------------------------------------*/ -#define CONFIG_ALTERA_UART 1 /* Use altera uart */ -#if defined(CONFIG_ALTERA_JTAG_UART) -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ -#else -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */ -#endif - -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */ -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ - -/*------------------------------------------------------------------------ - * EPCS Device -- None for stratix. - *----------------------------------------------------------------------*/ -#undef CONFIG_SYS_NIOS_EPCSBASE - -/*------------------------------------------------------------------------ - * DEBUG - *----------------------------------------------------------------------*/ -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */ - -/*------------------------------------------------------------------------ - * TIMEBASE -- - * - * The high res timer defaults to 1 msec. Since it includes the period - * registers, the interrupt frequency can be reduced using TMRCNT. - * If the default period is acceptable, TMRCNT can be left undefined. - * TMRMS represents the desired mecs per tick (msecs per interrupt). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_HZ 1000 /* Always 1000 */ -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */ -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec) */ -#define CONFIG_SYS_NIOS_TMRCNT \ - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) - -/*------------------------------------------------------------------------ - * STATUS LED -- Provides a simple blinking led. For Nios2 each board - * must implement its own led routines -- since leds are board-specific. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ -#define CONFIG_STATUS_LED /* Enable status driver */ - -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */ -#define STATUS_LED_STATE 1 /* Blinking */ -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */ - -/*------------------------------------------------------------------------ - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... - * and really doesn't need any additional clutter. So I choose the lazy - * way out to avoid changes there -- define the base address to ensure - * cache bypass so there's no need to monkey with inx/outx macros. - *----------------------------------------------------------------------*/ -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ -#define CONFIG_NET_MULTI -#define CONFIG_SMC91111 /* Using SMC91c111 */ -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ - -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.2.21 -#define CONFIG_SERVERIP 192.168.2.16 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#define CONFIG_CMD_BDI -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IMI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_LOADS -#define CONFIG_CMD_LOADB -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_MISC -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_RUN -#define CONFIG_CMD_SAVES - - -/*------------------------------------------------------------------------ - * MISC - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* Provide extended help*/ -#define CONFIG_SYS_PROMPT "==> " /* Command prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */ -#define CONFIG_SYS_MAXARGS 16 /* Max command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */ -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000 - -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h new file mode 100644 index 0000000..6cd5da7 --- /dev/null +++ b/include/configs/MPC8308RDB.h @@ -0,0 +1,560 @@ +/* + * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. + * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83xx 1 /* MPC83xx family */ +#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ +#define CONFIG_MPC8308RDB 1 /* MPC8308RDB board specific */ + +#define CONFIG_MISC_INIT_R + +/* + * On-board devices + * + * TSEC1 is SoC TSEC + * TSEC2 is VSC switch + */ +#define CONFIG_TSEC1 +#define CONFIG_VSC7385_ENET + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.66MHz, then + * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz + * We choose the A type silicon as default, so the core is 400Mhz. + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_CORE_TO_CSB_3X1) +/* + * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits + * in 8308's HRCWH according to the manual, but original Freescale's + * code has them and I've expirienced some problems using the board + * with BDI3000 attached when I've tried to set these bits to zero + * (UART doesn't work after the 'reset run' command). + */ +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH 0x01b7d103 +#define CONFIG_SYS_SICRL 0x00000040 /* 3.3V, no delay */ + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * SERDES + */ +#define CONFIG_FSL_SERDES +#define CONFIG_FSL_SERDES1 0xe3000 + +/* + * Arbiter Setup + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of two chips HY5PS12621BFP-C4 from HYNIX + */ + +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ + +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | 0x00010000 /* ODT_WR to CSn */ \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00220802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (5 << TIMING_CFG1_CASLAT_SHIFT) \ + | (6 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x27256222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (4 << TIMING_CFG2_CPO_SHIFT) \ + | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x121048c5 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x03600100 */ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_32_BE) + /* 0x43080000 */ + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0232 << SDRAM_MODE_SD_SHIFT)) + /* ODT 150ohm CL=3, AL=1 on SDRAM */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x07f00000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ + +/* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */ + +#define CONFIG_SYS_BR0_PRELIM (\ + CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\ + (2 << BR_PS_SHIFT) /* 16 bit port size */ |\ + BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +/* 127 64KB sectors and 8 8KB top sectors per device */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * NAND Flash on the Local Bus + */ +#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_NAND_BASE \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V ) /* valid */ +#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR ) + /* 0xFFFF8396 */ + +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ + +#ifdef CONFIG_VSC7385_ENET +#define CONFIG_TSEC2 +#define CONFIG_SYS_VSC7385_BASE 0xF0000000 +#define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */ +#define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/ +/* Access window base at VSC7385 base */ +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE +/* Access window size 128K */ +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 +/* The flash address and size of the VSC7385 firmware image */ +#define CONFIG_VSC7385_IMAGE 0xFE7FE000 +#define CONFIG_VSC7385_IMAGE_SIZE 8192 +#endif +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_FSL_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0x51}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + + +/* + * Board info - revision and where boot from + */ +#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +/* + * Fake PCIE2 definitions: there is no PCIE2 on this board but the code + * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this + */ +#define CONFIG_SYS_PCIE2_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 +#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 + +#define CONFIG_PCI +#define CONFIG_PCIE + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 + +/* + * TSEC + */ +#define CONFIG_NET_MULTI +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC0" + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ + BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define xstr(s) str(s) +#define str(s) #s + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=${consoledev},${baudrate}\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "addmisc=setenv bootargs ${bootargs}\0" \ + "kernel_addr=FE080000\0" \ + "fdt_addr=FE280000\0" \ + "ramdisk_addr=FE290000\0" \ + "u-boot=mpc8308rdb/u-boot.bin\0" \ + "kernel_addr_r=1000000\0" \ + "fdt_addr_r=C00000\0" \ + "hostname=mpc8308rdb\0" \ + "bootfile=mpc8308rdb/uImage\0" \ + "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0" \ + "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ + "flash_self=run ramargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdtfile};" \ + "run nfsargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "bootcmd=run flash_self\0" \ + "load=tftp ${loadaddr} ${u-boot}\0" \ + "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};cp.b ${fileaddr} " \ + xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ + "upd=run load update\0" \ + +#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 9a40adc..524afa5 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -36,6 +36,7 @@ #define CONFIG_MPC8313ERDB 1 #define CONFIG_PCI +#define CONFIG_FSL_ELBC 1 #define CONFIG_MISC_INIT_R diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index 6972fe8..f1b110b 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -197,6 +197,7 @@ #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 #define CONFIG_SYS_LBC_LBCR 0x00040000 +#define CONFIG_FSL_ELBC 1 /* * FLASH on the Local Bus diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index b30d0e3..9092755 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -223,6 +223,7 @@ #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8 #define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_FSL_ELBC 1 /* * FLASH on the Local Bus diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 1654f46..79dadc4 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -246,6 +246,7 @@ #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8 #define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_FSL_ELBC 1 /* * FLASH on the Local Bus diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index da4313a..a014ad0 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -1,5 +1,5 @@ /* - * Copyright 2008-2009 Freescale Semiconductor, Inc. + * Copyright 2007-2009,2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -27,6 +27,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include "../board/freescale/common/ics307_clk.h" + #ifdef CONFIG_MK_36BIT #define CONFIG_PHYS_64BIT 1 #endif @@ -70,15 +72,9 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -extern unsigned long get_board_ddr_clk(unsigned long dummy); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ -#define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq - from ICS307 instead of switches */ /* * These can be toggled for performance analysis, otherwise use default. @@ -669,6 +665,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h index 95ea275..7daf934 100644 --- a/include/configs/MPC8540EVAL.h +++ b/include/configs/MPC8540EVAL.h @@ -294,6 +294,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index e945da2..ae4fba8 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -403,6 +403,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 799d946..faba353 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -420,6 +420,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 3eb0049..fdd3597 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -462,6 +462,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 07a8e61..5011e5a 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -401,6 +401,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 4a4a9ed..98677e5 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -416,6 +416,7 @@ #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 6973538..0cc2d47 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -421,6 +421,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 0c43b2b..bb7bb47 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -539,6 +539,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 78b7369..57c2f2f 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2008 Freescale Semiconductor, Inc. + * Copyright 2007-2008,2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -27,6 +27,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include "../board/freescale/common/ics307_clk.h" + #ifdef CONFIG_MK_36BIT #define CONFIG_PHYS_64BIT #endif @@ -53,15 +55,9 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -extern unsigned long get_board_ddr_clk(unsigned long dummy); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() /* ddrclk for MPC85xx */ #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ -#define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq - from ICS307 instead of switches */ /* * These can be toggled for performance analysis, otherwise use default. @@ -574,6 +570,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h new file mode 100644 index 0000000..b42b5d0 --- /dev/null +++ b/include/configs/P1022DS.h @@ -0,0 +1,470 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> + * Timur Tabi <timur@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include "../board/freescale/common/ics307_clk.h" + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */ +#define CONFIG_P1022 +#define CONFIG_P1022DS +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ +#define CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_PHYS_64BIT +#define CONFIG_ENABLE_36BIT_PHYS +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() +#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE +#define CONFIG_BTB + +#define CONFIG_SYS_MEMTEST_START 0x00000000 +#define CONFIG_SYS_MEMTEST_END 0x7fffffff + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR + +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) /* pci0 */ +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) /* pci1 */ +#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR + 0xb000) /* pci2 */ + +/* DDR Setup */ +#define CONFIG_DDR_SPD +#define CONFIG_VERY_BIG_RAM +#define CONFIG_FSL_DDR3 + +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + +/* I2C addresses of SPD EEPROMs */ +#define CONFIG_SYS_SPD_BUS_NUM 1 +#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ + +/* + * Memory map + * + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable + * 0xffc0_0000 0xffc2_ffff PCI IO range 192K non-cacheable + * + * Localbus cacheable (TBD) + * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable + * + * Localbus non-cacheable + * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable + * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable + * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull + +#define CONFIG_FLASH_BR_PRELIM \ + (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V) +#define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7) + +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ + +#define CONFIG_SYS_BR1_PRELIM \ + (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM + +#define CONFIG_SYS_FLASH_BANKS_LIST \ + {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_MAX_FLASH_SECT 1024 + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_FSL_NGPIXIS +#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ +#define PIXIS_BASE_PHYS 0xfffdf0000ull + +#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7) + +#define PIXIS_LBMAP_SWITCH 7 +#define PIXIS_LBMAP_MASK 0xE0 +#define PIXIS_LBMAP_ALTBANK 0x20 + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_FSL_DIU_FB +#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) + +/* Video */ +/* #define CONFIG_VIDEO */ +#ifdef CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, Slot 2, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, direct to uli, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 3, Base address b000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +#ifdef CONFIG_PCI +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#endif + +/* SATA */ +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#ifdef CONFIG_FSL_SATA +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +#define CONFIG_MMC +#ifdef CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_GENERIC_MMC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#endif + +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +#define CONFIG_TSEC_ENET +#ifdef CONFIG_TSEC_ENET + +#define CONFIG_TSECV2 +#define CONFIG_NET_MULTI + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" + +#define TSEC1_PHY_ADDR 1 +#define TSEC2_PHY_ADDR 2 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OVERWRITE +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 + +#define CONFIG_LOADS_ECHO +#define CONFIG_SYS_LOADS_BAUD_CHANGE + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * USB + */ +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_FAT +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#define CONFIG_HOSTNAME p1022ds +#define CONFIG_ROOTPATH /opt/nfsroot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ + +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#define CONFIG_BOOTARGS + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "perf_mode=stable\0" \ + "memctl_intlv_ctl=2\0" \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=uramdisk\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=p1022ds.dtb\0" \ + "bdev=sda3\0" \ + "diuregs=md e002c000 1d\0" \ + "dium=mw e002c01c\0" \ + "diuerr=md e002c014 1\0" \ + "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \ + "monitor=0-DVI\0" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#endif diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index b891730..3cebbab 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -74,6 +74,7 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE +#define CONFIG_E1000 1 /* E1000 pci Ethernet card*/ #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif @@ -84,6 +85,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_MP #endif +#define CONFIG_HWCONFIG + /* * These can be toggled for performance analysis, otherwise use default. */ @@ -475,6 +478,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_CMD_MII #define CONFIG_CMD_PING #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_NET diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 66be725..569da4f 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2009 Freescale Semiconductor, Inc. + * Copyright 2007-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -27,6 +27,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include "../board/freescale/common/ics307_clk.h" + #ifdef CONFIG_MK_36BIT #define CONFIG_PHYS_64BIT #endif @@ -54,17 +56,9 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -#ifndef __ASSEMBLY__ -extern unsigned long calculate_board_sys_clk(unsigned long dummy); -extern unsigned long calculate_board_ddr_clk(unsigned long dummy); -/* extern unsigned long get_board_sys_clk(unsigned long dummy); */ -/* extern unsigned long get_board_ddr_clk(unsigned long dummy); */ -#endif -#define CONFIG_SYS_CLK_FREQ calculate_board_sys_clk(0) /* sysclk for MPC85xx */ -#define CONFIG_DDR_CLK_FREQ calculate_board_ddr_clk(0) /* ddrclk for MPC85xx */ +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() /* ddrclk for MPC85xx */ #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ -#define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq - from ICS307 instead of switches */ /* * These can be toggled for performance analysis, otherwise use default. @@ -553,6 +547,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy); #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/PM854.h b/include/configs/PM854.h index 4b9bcca..7426bca 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -326,6 +326,7 @@ #define CONFIG_CMD_MII #define CONFIG_CMD_DATE #define CONFIG_CMD_EEPROM +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/PM856.h b/include/configs/PM856.h index 1db20bc..0bd28fc 100644 --- a/include/configs/PM856.h +++ b/include/configs/PM856.h @@ -325,6 +325,7 @@ #define CONFIG_CMD_I2C #define CONFIG_CMD_DATE #define CONFIG_CMD_EEPROM +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index 1989e5a..5d424dd 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -380,6 +380,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h index eb8657b..70b7489 100644 --- a/include/configs/SIMPC8313.h +++ b/include/configs/SIMPC8313.h @@ -37,6 +37,7 @@ #define CONFIG_MPC8313 1 #define CONFIG_PCI +#define CONFIG_FSL_ELBC 1 #define CONFIG_MISC_INIT_R diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index d44fb07..90abe14 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -593,6 +593,7 @@ #define CONFIG_CMD_EEPROM #define CONFIG_CMD_DTT #define CONFIG_CMD_MII +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/XPEDITE5200.h b/include/configs/XPEDITE5200.h index 1a56c60..df5ef78 100644 --- a/include/configs/XPEDITE5200.h +++ b/include/configs/XPEDITE5200.h @@ -338,6 +338,7 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_SNTP +#define CONFIG_CMD_REGINFO /* * Miscellaneous configurable options diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h index 7fd3668..1d6091c 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/XPEDITE5370.h @@ -47,6 +47,7 @@ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_FSL_ELBC 1 /* * Multicore config @@ -396,6 +397,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_CMD_PING #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SNTP +#define CONFIG_CMD_REGINFO /* * Miscellaneous configurable options diff --git a/include/configs/bf518f-ezbrd.h b/include/configs/bf518f-ezbrd.h index 1e821d9..6eec1c9 100644 --- a/include/configs/bf518f-ezbrd.h +++ b/include/configs/bf518f-ezbrd.h @@ -63,6 +63,26 @@ #if !defined(__ADSPBF512__) && !defined(__ADSPBF514__) #define ADI_CMDS_NETWORK 1 #define CONFIG_BFIN_MAC +#define CONFIG_BFIN_MAC_PINS \ + { \ + P_MII0_ETxD0, \ + P_MII0_ETxD1, \ + P_MII0_ETxD2, \ + P_MII0_ETxD3, \ + P_MII0_ETxEN, \ + P_MII0_TxCLK, \ + P_MII0_PHYINT, \ + P_MII0_COL, \ + P_MII0_ERxD0, \ + P_MII0_ERxD1, \ + P_MII0_ERxD2, \ + P_MII0_ERxD3, \ + P_MII0_ERxDV, \ + P_MII0_ERxCLK, \ + P_MII0_CRS, \ + P_MII0_MDC, \ + P_MII0_MDIO, \ + 0 } #define CONFIG_NETCONSOLE 1 #define CONFIG_NET_MULTI 1 #endif @@ -117,8 +137,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/bf526-ezbrd.h b/include/configs/bf526-ezbrd.h index 711fa27..82396d0 100644 --- a/include/configs/bf526-ezbrd.h +++ b/include/configs/bf526-ezbrd.h @@ -134,8 +134,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* @@ -160,23 +158,19 @@ /* define to enable run status via led */ /* #define CONFIG_STATUS_LED */ #ifdef CONFIG_STATUS_LED +#define CONFIG_GPIO_LED #define CONFIG_BOARD_SPECIFIC_LED -#ifndef __ASSEMBLY__ -typedef unsigned int led_id_t; -void __led_init(led_id_t mask, int state); -void __led_set(led_id_t mask, int state); -void __led_toggle(led_id_t mask); -#endif /* use LED0 to indicate booting/alive */ #define STATUS_LED_BOOT 0 -#define STATUS_LED_BIT 1 +#define STATUS_LED_BIT GPIO_PF8 #define STATUS_LED_STATE STATUS_LED_ON #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) /* use LED1 to indicate crash */ #define STATUS_LED_CRASH 1 -#define STATUS_LED_BIT1 2 +#define STATUS_LED_BIT1 GPIO_PG11 #define STATUS_LED_STATE1 STATUS_LED_ON #define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) +/* #define STATUS_LED_BIT2 GPIO_PG12 */ #endif diff --git a/include/configs/bf527-ad7160-eval.h b/include/configs/bf527-ad7160-eval.h new file mode 100644 index 0000000..eb3a2b7 --- /dev/null +++ b/include/configs/bf527-ad7160-eval.h @@ -0,0 +1,148 @@ +/* + * U-boot - Configuration file for BF527 AD7160-EVAL board + */ + +#ifndef __CONFIG_BF527_AD7160_EVAL_H__ +#define __CONFIG_BF527_AD7160_EVAL_H__ + +#include <asm/config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf527-0.2 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 24000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 25 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 10 +#define CONFIG_MEM_SIZE 64 + +#define CONFIG_EBIU_SDRRC_VAL 0x03F6 +#define CONFIG_EBIU_SDGCTL_VAL (SCTLE | CL_3 | PASR_ALL | TRAS_6 | TRP_3 | TRCD_3 | TWR_2 | PSS) + +#define CONFIG_EBIU_AMGCTL_VAL (AMCKEN | AMBEN_ALL) +#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_15 | B1RAT_15 | B1HT_3 | B1RDYPOL | B0WAT_15 | B0RAT_15 | B0HT_3 | B0RDYPOL) +#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_15 | B3RAT_15 | B3HT_3 | B3RDYPOL | B2WAT_15 | B2RAT_15 | B2HT_3 | B2RDYPOL) + +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (640 * 1024) + + +/* + * NAND Settings + * (can't be used same time as ethernet) + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) +# define CONFIG_BFIN_NFC +# define CONFIG_BFIN_NFC_BOOTROM_ECC +#endif +#ifdef CONFIG_BFIN_NFC +#define CONFIG_BFIN_NFC_CTL_VAL 0x0033 +#define CONFIG_DRIVER_NAND_BFIN +#define CONFIG_SYS_NAND_BASE 0 /* not actually used */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#endif + + +/* + * Flash Settings + */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 259 + + +/* + * SPI Settings + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO + + +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x20000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#endif + + +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 + + +/* + * SPI_MMC Settings + */ +#define CONFIG_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_SPI_MMC +#define CONFIG_SPI_MMC_DEFAULT_CS (7 + GPIO_PH3) + + +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_UART_CONSOLE 0 + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +#endif diff --git a/include/configs/bf527-ezkit.h b/include/configs/bf527-ezkit.h index 7800c32..07e4ce8 100644 --- a/include/configs/bf527-ezkit.h +++ b/include/configs/bf527-ezkit.h @@ -138,8 +138,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h index c80ddca..37a7059 100644 --- a/include/configs/bf533-ezkit.h +++ b/include/configs/bf533-ezkit.h @@ -136,8 +136,6 @@ } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 #endif diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index 80c4884..02c8bc3 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -180,8 +180,6 @@ } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 #endif @@ -230,23 +228,19 @@ /* define to enable run status via led */ /* #define CONFIG_STATUS_LED */ #ifdef CONFIG_STATUS_LED +#define CONFIG_GPIO_LED #define CONFIG_BOARD_SPECIFIC_LED -#ifndef __ASSEMBLY__ -typedef unsigned int led_id_t; -void __led_init(led_id_t mask, int state); -void __led_set(led_id_t mask, int state); -void __led_toggle(led_id_t mask); -#endif -/* use LED1 to indicate booting/alive */ +/* use LED0 to indicate booting/alive */ #define STATUS_LED_BOOT 0 -#define STATUS_LED_BIT 1 +#define STATUS_LED_BIT GPIO_PF2 #define STATUS_LED_STATE STATUS_LED_ON #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) -/* use LED2 to indicate crash */ +/* use LED1 to indicate crash */ #define STATUS_LED_CRASH 1 -#define STATUS_LED_BIT1 2 +#define STATUS_LED_BIT1 GPIO_PF3 #define STATUS_LED_STATE1 STATUS_LED_ON #define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) +/* #define STATUS_LED_BIT2 GPIO_PF4 */ #endif /* define to enable splash screen support */ diff --git a/include/configs/bf537-pnav.h b/include/configs/bf537-pnav.h index cf40d06..39bbb41 100644 --- a/include/configs/bf537-pnav.h +++ b/include/configs/bf537-pnav.h @@ -132,7 +132,6 @@ #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) -#define BFIN_NAND_READY PF12 #define BFIN_NAND_WRITE(addr, cmd) \ do { \ bfin_write8(addr, cmd); \ @@ -141,13 +140,7 @@ #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) -#define NAND_PLAT_DEV_READY(chip) (bfin_read_PORTHIO() & BFIN_NAND_READY) -#define NAND_PLAT_INIT() \ - do { \ - bfin_write_PORTH_FER(bfin_read_PORTH_FER() & ~BFIN_NAND_READY); \ - bfin_write_PORTHIO_DIR(bfin_read_PORTHIO_DIR() & ~BFIN_NAND_READY); \ - bfin_write_PORTHIO_INEN(bfin_read_PORTHIO_INEN() | BFIN_NAND_READY); \ - } while (0) +#define NAND_PLAT_GPIO_DEV_READY GPIO_PF12 /* @@ -155,8 +148,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index 92ceb38..96704d7 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -137,8 +137,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* @@ -157,7 +155,6 @@ #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) -#define BFIN_NAND_READY PF3 #define BFIN_NAND_WRITE(addr, cmd) \ do { \ bfin_write8(addr, cmd); \ @@ -166,13 +163,7 @@ #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) -#define NAND_PLAT_DEV_READY(chip) (bfin_read_PORTFIO() & BFIN_NAND_READY) -#define NAND_PLAT_INIT() \ - do { \ - bfin_write_PORTF_FER(bfin_read_PORTF_FER() & ~BFIN_NAND_READY); \ - bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() & ~BFIN_NAND_READY); \ - bfin_write_PORTFIO_INEN(bfin_read_PORTFIO_INEN() | BFIN_NAND_READY); \ - } while (0) +#define NAND_PLAT_GPIO_DEV_READY GPIO_PF3 /* @@ -268,8 +259,6 @@ #define CONFIG_RTC_BFIN #define CONFIG_UART_CONSOLE 0 -/* #define CONFIG_BF537_STAMP_LEDCMD 1 */ - /* Define if want to do post memory test */ #undef CONFIG_POST #ifdef CONFIG_POST diff --git a/include/configs/bf538f-ezkit.h b/include/configs/bf538f-ezkit.h index 59e0565..1c14b6b 100644 --- a/include/configs/bf538f-ezkit.h +++ b/include/configs/bf538f-ezkit.h @@ -134,8 +134,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/bf548-ezkit.h b/include/configs/bf548-ezkit.h index f9c9711..60cca0c 100644 --- a/include/configs/bf548-ezkit.h +++ b/include/configs/bf548-ezkit.h @@ -140,8 +140,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/bf561-acvilon.h b/include/configs/bf561-acvilon.h index 0be170c..0c0204f 100644 --- a/include/configs/bf561-acvilon.h +++ b/include/configs/bf561-acvilon.h @@ -131,7 +131,6 @@ #define CONFIG_ENV_SECT_SIZE (1056 * 8) #define CONFIG_ENV_OFFSET ((16 + 256) * 1056) #define CONFIG_ENV_SIZE (8 * 1056) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) /* @@ -145,7 +144,6 @@ #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 3)) -#define BFIN_NAND_READY PF10 #define BFIN_NAND_WRITE(addr, cmd) \ do { \ bfin_write8(addr, cmd); \ @@ -154,12 +152,7 @@ #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) -#define NAND_PLAT_DEV_READY(chip) (bfin_read_FIO0_FLAG_D() & BFIN_NAND_READY) -#define NAND_PLAT_INIT() \ - do { \ - bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() & ~BFIN_NAND_READY); \ - bfin_write_FIO0_INEN(bfin_read_FIO0_INEN() | BFIN_NAND_READY); \ - } while (0) +#define NAND_PLAT_GPIO_DEV_READY GPIO_PF10 /* diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h index 1e3fdef..036bfe4 100644 --- a/include/configs/bf561-ezkit.h +++ b/include/configs/bf561-ezkit.h @@ -151,8 +151,6 @@ } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 #endif diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index 1896cf5..901a32f 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -83,6 +83,7 @@ # define CONFIG_CMD_CPLBINFO # define CONFIG_CMD_ELF # define CONFIG_ELF_SIMPLE_LOAD +# define CONFIG_CMD_GPIO # define CONFIG_CMD_KGDB # define CONFIG_CMD_REGINFO # define CONFIG_CMD_STRINGS @@ -247,12 +248,26 @@ # define CONFIG_SYS_AUTOLOAD "no" # endif # endif +# define CONFIG_IP_DEFRAG # define CONFIG_NET_RETRY_COUNT 20 #endif /* + * I2C Settings + */ +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +# ifndef CONFIG_SYS_I2C_SPEED +# define CONFIG_SYS_I2C_SPEED 50000 +# endif +# ifndef CONFIG_SYS_I2C_SLAVE +# define CONFIG_SYS_I2C_SLAVE 0 +# endif +#endif + +/* * Misc Settings */ +#define CONFIG_BFIN_SPI_GPIO_CS /* Only matters if BFIN_SPI is enabled */ #define CONFIG_LZMA #endif diff --git a/include/configs/cm-bf527.h b/include/configs/cm-bf527.h index ad1dd12..e0c6d53 100644 --- a/include/configs/cm-bf527.h +++ b/include/configs/cm-bf527.h @@ -117,8 +117,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/cm-bf537e.h b/include/configs/cm-bf537e.h index 8d0bc12..742df9c 100644 --- a/include/configs/cm-bf537e.h +++ b/include/configs/cm-bf537e.h @@ -119,8 +119,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/cm-bf537u.h b/include/configs/cm-bf537u.h index bbea3ab..9def99f 100644 --- a/include/configs/cm-bf537u.h +++ b/include/configs/cm-bf537u.h @@ -120,8 +120,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/cm-bf548.h b/include/configs/cm-bf548.h index 93c4c8d..63b9399 100644 --- a/include/configs/cm-bf548.h +++ b/include/configs/cm-bf548.h @@ -107,8 +107,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/colibri_pxa270.h b/include/configs/colibri_pxa270.h new file mode 100644 index 0000000..277ff67 --- /dev/null +++ b/include/configs/colibri_pxa270.h @@ -0,0 +1,278 @@ +/* + * Toradex Colibri PXA270 configuration file + * + * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Board Configuration Options + */ +#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */ +#define CONFIG_VPAC270 1 /* Toradex Colibri PXA270 board */ + +#undef BOARD_LATE_INIT +#undef CONFIG_SKIP_RELOCATE_UBOOT +#undef CONFIG_USE_IRQ +#undef CONFIG_SKIP_LOWLEVEL_INIT + +/* + * Environment settings + */ +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +#define CONFIG_ENV_OVERWRITE /* override default environment */ + +#define CONFIG_BOOTCOMMAND \ + "if mmc init && fatload mmc 0 0xa0000000 uImage; then " \ + "bootm 0xa0000000; " \ + "fi; " \ + "if usb reset && fatload usb 0 0xa0000000 uImage; then " \ + "bootm 0xa0000000; " \ + "fi; " \ + "bootm 0x80000;" +#define CONFIG_BOOTARGS "console=tty0 console=ttyS0,115200" +#define CONFIG_TIMESTAMP +#define CONFIG_BOOTDELAY 2 /* Autoboot delay */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS + +#define CONFIG_LZMA /* LZMA compression support */ + +/* + * Serial Console Configuration + */ +#define CONFIG_PXA_SERIAL +#define CONFIG_FFUART 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Bootloader Components Configuration + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_NET +#define CONFIG_CMD_ENV +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_MMC +#define CONFIG_CMD_USB +#define CONFIG_CMD_FLASH + +/* + * Networking Configuration + * chip on the Voipac PXA270 board + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +#define CONFIG_NET_MULTI 1 +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DM9000_BASE 0x08000000 +#define DM9000_IO (CONFIG_DM9000_BASE) +#define DM9000_DATA (CONFIG_DM9000_BASE + 4) +#define CONFIG_NET_RETRY_COUNT 10 + +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#endif + +/* + * MMC Card Configuration + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_PXA_MMC +#define CONFIG_SYS_MMC_BASE 0xF0000000 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * KGDB + */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * HUSH Shell Configuration + */ +#define CONFIG_SYS_HUSH_PARSER 1 +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */ +#else +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#endif +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_DEVICE_NULLDEV 1 + +/* + * Clock Configuration + */ +#undef CONFIG_SYS_CLKS_IN_HZ +#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */ +#define CONFIG_SYS_CPUSPEED 0x290 /* 520 MHz */ + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * DRAM Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* We have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ + +#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */ +#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB DRAM */ + +#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR (0xa1000000) + +/* + * NOR FLASH + */ +#ifdef CONFIG_CMD_FLASH +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER 1 + +#define CONFIG_SYS_MAX_FLASH_SECT (4 + 255) +#define CONFIG_SYS_MAX_FLASH_BANKS 1 + +#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ) + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 +#define CONFIG_SYS_FLASH_PROTECTION 1 + +#define CONFIG_ENV_IS_IN_FLASH 1 + +#else /* No flash */ +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_ENV_IS_NOWHERE +#endif + +#define CONFIG_SYS_MONITOR_BASE 0x000000 +#define CONFIG_SYS_MONITOR_LEN 0x40000 + +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x40000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + + +/* + * GPIO settings + */ +#define CONFIG_SYS_GPSR0_VAL 0x00000000 +#define CONFIG_SYS_GPSR1_VAL 0x00020000 +#define CONFIG_SYS_GPSR2_VAL 0x0002C000 +#define CONFIG_SYS_GPSR3_VAL 0x00000000 + +#define CONFIG_SYS_GPCR0_VAL 0x00000000 +#define CONFIG_SYS_GPCR1_VAL 0x00000000 +#define CONFIG_SYS_GPCR2_VAL 0x00000000 +#define CONFIG_SYS_GPCR3_VAL 0x00000000 + +#define CONFIG_SYS_GPDR0_VAL 0x08000000 +#define CONFIG_SYS_GPDR1_VAL 0x0002A981 +#define CONFIG_SYS_GPDR2_VAL 0x0202FC00 +#define CONFIG_SYS_GPDR3_VAL 0x00000000 + +#define CONFIG_SYS_GAFR0_L_VAL 0x00100000 +#define CONFIG_SYS_GAFR0_U_VAL 0x00C00010 +#define CONFIG_SYS_GAFR1_L_VAL 0x999A901A +#define CONFIG_SYS_GAFR1_U_VAL 0xAAA00008 +#define CONFIG_SYS_GAFR2_L_VAL 0xAAAAAAAA +#define CONFIG_SYS_GAFR2_U_VAL 0x0109A000 +#define CONFIG_SYS_GAFR3_L_VAL 0x54000300 +#define CONFIG_SYS_GAFR3_U_VAL 0x00024001 + +#define CONFIG_SYS_PSSR_VAL 0x30 + +/* + * Clock settings + */ +#define CONFIG_SYS_CKEN 0x00500240 +#define CONFIG_SYS_CCCR 0x02000290 + +/* + * Memory settings + */ +#define CONFIG_SYS_MSC0_VAL 0x000095f2 +#define CONFIG_SYS_MSC1_VAL 0x00007ff4 +#define CONFIG_SYS_MSC2_VAL 0x00000000 +#define CONFIG_SYS_MDCNFG_VAL 0x08000ac9 +#define CONFIG_SYS_MDREFR_VAL 0x2013e01e +#define CONFIG_SYS_MDMRS_VAL 0x00320032 +#define CONFIG_SYS_FLYCNFG_VAL 0x00000000 +#define CONFIG_SYS_SXCNFG_VAL 0x40044004 + +/* + * PCMCIA and CF Interfaces + */ +#define CONFIG_SYS_MECR_VAL 0x00000001 +#define CONFIG_SYS_MCMEM0_VAL 0x00014307 +#define CONFIG_SYS_MCMEM1_VAL 0x00014307 +#define CONFIG_SYS_MCATT0_VAL 0x0001c787 +#define CONFIG_SYS_MCATT1_VAL 0x0001c787 +#define CONFIG_SYS_MCIO0_VAL 0x0001430f +#define CONFIG_SYS_MCIO1_VAL 0x0001430f + +/* + * USB + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_BOARD_INIT +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x4C000000 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "tdex270" +#define CONFIG_USB_STORAGE +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/cpuat91.h b/include/configs/cpuat91.h index b4fda76..049298c 100644 --- a/include/configs/cpuat91.h +++ b/include/configs/cpuat91.h @@ -131,15 +131,12 @@ (CONFIG_SYS_MEMTEST_START + PHYS_SDRAM_SIZE - 512 * 1024) #define CONFIG_NET_MULTI 1 -#ifdef CONFIG_NET_MULTI #define CONFIG_DRIVER_AT91EMAC 1 #define CONFIG_SYS_RX_ETH_BUFFER 8 -#else -#define CONFIG_DRIVER_ETHER 1 -#endif +#define CONFIG_RMII 1 +#define CONFIG_MII 1 +#define CONFIG_DRIVER_AT91EMAC_PHYADDR 1 #define CONFIG_NET_RETRY_COUNT 20 -#define CONFIG_AT91C_USE_RMII 1 -#define CONFIG_PHY_ADDRESS (1 << 5) #define CONFIG_KS8721_PHY 1 #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h index c3d95a0..055931c 100644 --- a/include/configs/edminiv2.h +++ b/include/configs/edminiv2.h @@ -131,12 +131,23 @@ * Commands configuration - using default command set for now */ #include <config_cmd_default.h> + /* - * Disabling some default commands for staggered bring-up + * Network */ -#undef CONFIG_CMD_BOOTD /* no bootd since no net */ -#undef CONFIG_CMD_NET /* no net since no eth */ -#undef CONFIG_CMD_NFS /* no NFS since no net */ + +#ifdef CONFIG_CMD_NET +#define CONFIG_MVGBE /* Enable Marvell GbE Driver */ +#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */ +#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */ +#define CONFIG_PHY_BASE_ADR 0x8 +#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_NET_MULTI /* specify more that one ports available */ +#define CONFIG_MII /* expose smi ove miiphy interface */ +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#endif /* * Environment variables configurations diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h index 2fbc6ad..eb3fa57 100644 --- a/include/configs/guruplug.h +++ b/include/configs/guruplug.h @@ -172,9 +172,9 @@ #define CONFIG_NET_MULTI /* specify more that one ports available */ #define CONFIG_MII /* expose smi ove miiphy interface */ #define CONFIG_CMD_MII -#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ -#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,1} /* enable both ports */ +#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv88e1121 PHY */ diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h index 2eef5ef..2c0a263 100644 --- a/include/configs/ibf-dsp561.h +++ b/include/configs/ibf-dsp561.h @@ -58,6 +58,18 @@ /* + * Network Settings + */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_NET_MULTI +#define CONFIG_DRIVER_AX88180 1 +#define AX88180_BASE 0x2c000000 +#define CONFIG_HOSTNAME ibf-dsp561 +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ + + +/* * Flash Settings */ #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ @@ -126,8 +138,6 @@ } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 #endif diff --git a/include/configs/ip04.h b/include/configs/ip04.h index 425a745..c024d78 100644 --- a/include/configs/ip04.h +++ b/include/configs/ip04.h @@ -116,7 +116,6 @@ #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) -#define BFIN_NAND_READY PF10 #define BFIN_NAND_WRITE(addr, cmd) \ do { \ bfin_write8(addr, cmd); \ @@ -125,14 +124,7 @@ #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) -#define NAND_PLAT_DEV_READY(chip) (bfin_read_FIO_FLAG_D() & BFIN_NAND_READY) -#define NAND_PLAT_INIT() \ - do { \ - bfin_write_FIO_DIR(bfin_read_FIO_DIR() & ~BFIN_NAND_READY); \ - bfin_write_FIO_INEN(bfin_read_FIO_INEN() | BFIN_NAND_READY); \ - bfin_write_FIO_EDGE(bfin_read_FIO_EDGE() & ~BFIN_NAND_READY); \ - bfin_write_FIO_POLAR(bfin_read_FIO_POLAR() & ~BFIN_NAND_READY); \ - } while (0) +#define NAND_PLAT_GPIO_DEV_READY GPIO_PF10 /* diff --git a/include/configs/km_arm.h b/include/configs/km_arm.h index a928c2c..6519c90 100644 --- a/include/configs/km_arm.h +++ b/include/configs/km_arm.h @@ -127,9 +127,9 @@ #define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_NET_MULTI /* specify more that one ports available */ #define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ -#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ #define CONFIG_RESET_PHY_R /* use reset_phy() to init 88E1118 PHY */ diff --git a/include/configs/mv88f6281gtw_ge.h b/include/configs/mv88f6281gtw_ge.h index 96b4d1c..9ef03a6 100644 --- a/include/configs/mv88f6281gtw_ge.h +++ b/include/configs/mv88f6281gtw_ge.h @@ -172,9 +172,9 @@ #define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_NET_MULTI /* specify more that one ports available */ #define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ -#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ #endif /* CONFIG_CMD_NET */ diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index d2f4502..52fa73d 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -183,9 +183,9 @@ #define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_NET_MULTI /* specify more that one ports available */ #define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ -#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0x8 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h index 3d8e25c..5857301 100644 --- a/include/configs/rd6281a.h +++ b/include/configs/rd6281a.h @@ -171,8 +171,8 @@ #define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_NET_MULTI /* specify more that one ports available */ #define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */ -#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,1} /* enable both ports */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ +#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_MV88E61XX_MULTICHIP_ADRMODE #define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */ #define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */ diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index aeac2de..3f4056e 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -487,6 +487,7 @@ #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_ELF +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index dab4f80..53d06ed 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -382,6 +382,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index e9edc44..c5de86e 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -174,9 +174,9 @@ #define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_NET_MULTI /* specify more that one ports available */ #define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ -#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 89f7cc4..ad70109 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -355,6 +355,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_SNTP #define CONFIG_CMD_USB +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index 86b231c..891d2bf 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -321,6 +321,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C +#define CONFIG_CMD_REGINFO #if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_SAVEENV diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 2783f9e..363f7b4 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -353,6 +353,7 @@ #define CONFIG_CMD_NFS #define CONFIG_CMD_PING #define CONFIG_CMD_SNTP +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI diff --git a/include/configs/tcm-bf518.h b/include/configs/tcm-bf518.h index 9c04d8a..52055e8 100644 --- a/include/configs/tcm-bf518.h +++ b/include/configs/tcm-bf518.h @@ -106,8 +106,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/tcm-bf537.h b/include/configs/tcm-bf537.h index 409a042..24ce8f8 100644 --- a/include/configs/tcm-bf537.h +++ b/include/configs/tcm-bf537.h @@ -120,8 +120,6 @@ */ #define CONFIG_BFIN_TWI_I2C 1 #define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h new file mode 100644 index 0000000..1589913 --- /dev/null +++ b/include/configs/ve8313.h @@ -0,0 +1,511 @@ +/* + * Copyright (C) Freescale Semiconductor, Inc. 2006. + * + * (C) Copyright 2010 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +/* + * ve8313 board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 +#define CONFIG_MPC83xx 1 +#define CONFIG_MPC831x 1 +#define CONFIG_MPC8313 1 +#define CONFIG_VE8313 1 + +#define CONFIG_PCI 1 + +#define CONFIG_BOARD_EARLY_INIT_F 1 + +/* + * On-board devices + * + */ +#define CONFIG_83XX_CLKIN 32000000 /* in Hz */ + +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +#define CONFIG_SYS_IMMR 0xE0000000 + +#define CONFIG_SYS_MEMTEST_START 0x00001000 +#define CONFIG_SYS_MEMTEST_END 0x07000000 + +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */ + +/* + * Device configurations + */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE + +/* + * Manually set up DDR parameters, as this board does not + * have the SPD connected to I2C. + */ +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ +#define CONFIG_SYS_DDR_CONFIG ( CSCONFIG_EN \ + | CSCONFIG_AP \ + | 0x00040000 /* TODO */ \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 ) + /* 0x80840102 */ + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ + | ( 3 << TIMING_CFG0_RRT_SHIFT ) \ + | ( 2 << TIMING_CFG0_WWT_SHIFT ) \ + | ( 7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ + | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) + /* 0x0e720802 */ +#define CONFIG_SYS_DDR_TIMING_1 ( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \ + | ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ + | ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \ + | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ + | ( 6 << TIMING_CFG1_REFREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) + /* 0x26256222 */ +#define CONFIG_SYS_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \ + | ( 5 << TIMING_CFG2_CPO_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ + | ( 1 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ + | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ + | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) ) + /* 0x029028c7 */ +#define CONFIG_SYS_DDR_INTERVAL ( ( 0x320 << SDRAM_INTERVAL_REFINT_SHIFT ) \ + | ( 0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) + /* 0x03202000 */ +#define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_32_BE ) + /* 0x43080000 */ +#define CONFIG_SYS_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \ + | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) ) + /* 0x44400232 */ +#define CONFIG_SYS_DDR_MODE_2 0x8000C000 + +#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 + /*0x02000000*/ +#define CONFIG_SYS_DDRCDR_VALUE ( DDRCDR_EN \ + | DDRCDR_PZ_NOMZ \ + | DDRCDR_NZ_NOMZ \ + | DDRCDR_M_ODR ) + /* 0x73000002 */ + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ + +#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE | \ + (2 << BR_PS_SHIFT) | /* 16 bit */ \ + BR_V) /* valid */ +#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV4 \ + | OR_GPCM_SCY_5 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EAD) + /* 0xfe000c55 */ + +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32 MB window size */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/ + +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) + +/* + * Local Bus LCRR and LBCR regs + */ +#define CONFIG_SYS_LCRR_EADC LCRR_EADC_3 +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 + +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +#define CONFIG_SYS_LBC_MRTPR 0x20000000 + +/* + * NAND settings + */ +#define CONFIG_SYS_NAND_BASE 0x61000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 + +#define CONFIG_SYS_NAND_BR_PRELIM ( CONFIG_SYS_NAND_BASE \ + | BR_PS_8 \ + | BR_DECC_CHK_GEN \ + | BR_MS_FCM \ + | BR_V ) /* valid */ + /* 0x61000c21 */ +#define CONFIG_SYS_NAND_OR_PRELIM (0xffff8000 \ + | OR_FCM_BCTLD \ + | OR_FCM_CHT \ + | OR_FCM_SCY_2 \ + | OR_FCM_RST \ + | OR_FCM_TRLX) + /* 0xffff90ac */ + +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM + +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ + +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM + +/* CS2 NvRAM */ +#define CONFIG_SYS_BR2_PRELIM (0x60000000 \ + | BR_PS_8 \ + | BR_V) + /* 0x60000801 */ +#define CONFIG_SYS_OR2_PRELIM (0xfffe0000 \ + | OR_GPCM_CSNT \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_3 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + /* 0xfffe0937 */ +/* local bus read write buffer mapping SRAM@0x64000000 */ +#define CONFIG_SYS_BR3_PRELIM (0x62000000 \ + | BR_PS_16 \ + | BR_V) + /* 0x62001001 */ + +#define CONFIG_SYS_OR3_PRELIM (0xfe000000 \ + | OR_GPCM_CSNT \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + /* 0xfe0009f7 */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#if defined(CONFIG_PCI) +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#endif + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ + +#define CONFIG_NET_MULTI + +#define CONFIG_TSEC1 +#ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC1" +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define TSEC1_PHY_ADDR 0x01 +#define TSEC1_FLAGS 0 +#define TSEC1_PHYIDX 0 +#endif + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC1" + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x4000 +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_PCI + +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */ +#define CONFIG_SYS_HZ 1000 /* 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* 0x64050000 */ +#define CONFIG_SYS_HRCW_LOW (\ + 0x20000000 /* reserved, must be set */ |\ + HRCWL_DDRCM |\ + HRCWL_CSB_TO_CLKIN_4X1 | \ + HRCWL_CORE_TO_CSB_2_5X1) + +/* 0xa0600004 */ +#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \ + HRCWH_PCI_ARBITER_ENABLE | \ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_TSEC1M_IN_MII | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_EARLY) + +/* System IO Config */ +#define CONFIG_SYS_SICRH (0x01000000 | \ + SICRH_ETSEC2_B | \ + SICRH_ETSEC2_C | \ + SICRH_ETSEC2_D | \ + SICRH_ETSEC2_E | \ + SICRH_ETSEC2_F | \ + SICRH_ETSEC2_G | \ + SICRH_TSOBI1 | \ + SICRH_TSOBI2) + /* 0x010fff03 */ +#define CONFIG_SYS_SICRL (SICRL_LBC | \ + SICRL_SPI_A | \ + SICRL_SPI_B | \ + SICRL_SPI_C | \ + SICRL_SPI_D | \ + SICRL_ETSEC2_A) + /* 0x33fc0003) */ + +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE) + +#define CONFIG_SYS_HID2 HID2_HBE + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* DDR @ 0x00000000 */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \ + BATU_VS | BATU_VP) + +#if defined(CONFIG_PCI) +/* PCI @ 0x80000000 */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \ + BATU_VS | BATU_VP) +#else +#define CONFIG_SYS_IBAT1L (0) +#define CONFIG_SYS_IBAT1U (0) +#define CONFIG_SYS_IBAT2L (0) +#define CONFIG_SYS_IBAT2U (0) +#endif + +/* PCI2 not supported on 8313 */ +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) + +/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | \ + BATU_VP) + +/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ +#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +/* FPGA, SRAM, NAND @ 0x60000000 */ +#define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_NETDEV eth0 + +#define CONFIG_HOSTNAME ve8313 +#define CONFIG_UBOOTPATH ve8313/u-boot.bin + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#define CONFIG_BAUDRATE 115200 + +#define XMK_STR(x) #x +#define MK_STR(x) XMK_STR(x) + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" MK_STR(CONFIG_NETDEV) "\0" \ + "ethprime=" MK_STR(CONFIG_TSEC1_NAME) "\0" \ + "u-boot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "u-boot_addr_r=100000\0" \ + "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ + "update=protect off " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \ + "erase " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \ + "cp.b ${u-boot_addr_r} " MK_STR(CONFIG_SYS_FLASH_BASE) \ + " ${filesize};" \ + "protect on " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \ + +#undef MK_STR +#undef XMK_STR + +#endif /* __CONFIG_H */ diff --git a/include/configs/vpac270.h b/include/configs/vpac270.h new file mode 100644 index 0000000..6d02995 --- /dev/null +++ b/include/configs/vpac270.h @@ -0,0 +1,323 @@ +/* + * Voipac PXA270 configuration file + * + * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Board Configuration Options + */ +#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */ +#define CONFIG_VPAC270 1 /* Voipac PXA270 board */ + +#undef BOARD_LATE_INIT +#undef CONFIG_SKIP_RELOCATE_UBOOT +#undef CONFIG_USE_IRQ +#undef CONFIG_SKIP_LOWLEVEL_INIT + +/* + * Environment settings + */ +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +#define CONFIG_ENV_OVERWRITE /* override default environment */ + +#define CONFIG_BOOTCOMMAND \ + "if mmc init && fatload mmc 0 0xa4000000 uImage; then " \ + "bootm 0xa4000000; " \ + "fi; " \ + "if usb reset && fatload usb 0 0xa4000000 uImage; then " \ + "bootm 0xa4000000; " \ + "fi; " \ + "bootm 0x40000;" +#define CONFIG_BOOTARGS "console=tty0 console=ttyS0,115200" +#define CONFIG_TIMESTAMP +#define CONFIG_BOOTDELAY 2 /* Autoboot delay */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS + +#define CONFIG_LZMA /* LZMA compression support */ + +/* + * Serial Console Configuration + */ +#define CONFIG_PXA_SERIAL +#define CONFIG_FFUART 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Bootloader Components Configuration + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_NET +#define CONFIG_CMD_ENV +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_MMC +#define CONFIG_CMD_USB +#undef CONFIG_LCD +#define CONFIG_CMD_IDE + +#ifdef CONFIG_ONENAND_U_BOOT +#undef CONFIG_CMD_FLASH +#define CONFIG_CMD_ONENAND +#else +#define CONFIG_CMD_FLASH +#undef CONFIG_CMD_ONENAND +#endif + +/* + * Networking Configuration + * chip on the Voipac PXA270 board + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +#define CONFIG_NET_MULTI 1 +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DM9000_BASE 0x08000300 /* CS2 */ +#define DM9000_IO (CONFIG_DM9000_BASE) +#define DM9000_DATA (CONFIG_DM9000_BASE + 4) +#define CONFIG_NET_RETRY_COUNT 10 + +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#endif + +/* + * MMC Card Configuration + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_PXA_MMC +#define CONFIG_SYS_MMC_BASE 0xF0000000 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * KGDB + */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * HUSH Shell Configuration + */ +#define CONFIG_SYS_HUSH_PARSER 1 +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */ +#else +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#endif +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_DEVICE_NULLDEV 1 + +/* + * Clock Configuration + */ +#undef CONFIG_SYS_CLKS_IN_HZ +#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */ +#define CONFIG_SYS_CPUSPEED 0x190 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */ + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * DRAM Map + */ +#define CONFIG_NR_DRAM_BANKS 2 /* We have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ +#define PHYS_SDRAM_2 0x80000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */ + +#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */ +#define CONFIG_SYS_DRAM_SIZE 0x10000000 /* 256 MB DRAM */ + +#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR (0x5c000000) + +/* + * NOR FLASH + */ +#if defined(CONFIG_CMD_FLASH) /* NOR */ +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ +#define PHYS_FLASH_2 0x02000000 /* Flash Bank #2 */ + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER 1 + +#define CONFIG_SYS_MAX_FLASH_SECT (4 + 255) +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } + +#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ) + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 +#define CONFIG_SYS_FLASH_PROTECTION 1 + +#define CONFIG_ENV_IS_IN_FLASH 1 + +#elif defined(CONFIG_CMD_ONENAND) /* OneNAND */ +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_ONENAND_BASE 0x00000000 +#define CONFIG_ENV_IS_IN_ONENAND 1 + +#else /* No flash */ +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_ENV_IS_NOWHERE +#endif + +#define CONFIG_SYS_MONITOR_BASE 0x000000 +#define CONFIG_SYS_MONITOR_LEN 0x40000 + +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x40000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * IDE + */ +#ifdef CONFIG_CMD_IDE +#define CONFIG_LBA48 +#undef CONFIG_IDE_LED +#undef CONFIG_IDE_RESET + +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 1 + +#define CONFIG_SYS_ATA_BASE_ADDR 0x0c000000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x120 +#define CONFIG_SYS_ATA_REG_OFFSET 0x120 +#define CONFIG_SYS_ATA_ALT_OFFSET 0x120 + +#define CONFIG_SYS_ATA_STRIDE 2 +#endif + +/* + * GPIO settings + */ +#define CONFIG_SYS_GPSR0_VAL 0x01308800 +#define CONFIG_SYS_GPSR1_VAL 0x00cf0000 +#define CONFIG_SYS_GPSR2_VAL 0x922ac000 +#define CONFIG_SYS_GPSR3_VAL 0x0161e800 + +#define CONFIG_SYS_GPCR0_VAL 0x00010000 +#define CONFIG_SYS_GPCR1_VAL 0x0 +#define CONFIG_SYS_GPCR2_VAL 0x0 +#define CONFIG_SYS_GPCR3_VAL 0x0 + +#define CONFIG_SYS_GPDR0_VAL 0xcbb18800 +#define CONFIG_SYS_GPDR1_VAL 0xfccfa981 +#define CONFIG_SYS_GPDR2_VAL 0x922affff +#define CONFIG_SYS_GPDR3_VAL 0x0161e904 + +#define CONFIG_SYS_GAFR0_L_VAL 0x00100000 +#define CONFIG_SYS_GAFR0_U_VAL 0xa5da8510 +#define CONFIG_SYS_GAFR1_L_VAL 0x6992901a +#define CONFIG_SYS_GAFR1_U_VAL 0xaaa5a0aa +#define CONFIG_SYS_GAFR2_L_VAL 0xaaaaaaaa +#define CONFIG_SYS_GAFR2_U_VAL 0x4109a401 +#define CONFIG_SYS_GAFR3_L_VAL 0x54010310 +#define CONFIG_SYS_GAFR3_U_VAL 0x00025401 + +#define CONFIG_SYS_PSSR_VAL 0x30 + +/* + * Clock settings + */ +#define CONFIG_SYS_CKEN 0x00500240 +#define CONFIG_SYS_CCCR 0x02000290 + +/* + * Memory settings + */ +#define CONFIG_SYS_MSC0_VAL 0x3ffc95fa +#define CONFIG_SYS_MSC1_VAL 0x02ccf974 +#define CONFIG_SYS_MSC2_VAL 0x00000000 +#define CONFIG_SYS_MDCNFG_VAL 0x8ad30ad3 +#define CONFIG_SYS_MDREFR_VAL 0x201fe01e +#define CONFIG_SYS_MDMRS_VAL 0x00000000 +#define CONFIG_SYS_FLYCNFG_VAL 0x00000000 +#define CONFIG_SYS_SXCNFG_VAL 0x40044004 +#define CONFIG_SYS_MEM_BUF_IMP 0x0f + +/* + * PCMCIA and CF Interfaces + */ +#define CONFIG_SYS_MECR_VAL 0x00000001 +#define CONFIG_SYS_MCMEM0_VAL 0x00014307 +#define CONFIG_SYS_MCMEM1_VAL 0x00014307 +#define CONFIG_SYS_MCATT0_VAL 0x0001c787 +#define CONFIG_SYS_MCATT1_VAL 0x0001c787 +#define CONFIG_SYS_MCIO0_VAL 0x0001430f +#define CONFIG_SYS_MCIO1_VAL 0x0001430f + +/* + * LCD + */ +#ifdef CONFIG_LCD +#define CONFIG_VOIPAC_LCD +#endif + +/* + * USB + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_BOARD_INIT +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x4C000000 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "vpac270" +#define CONFIG_USB_STORAGE +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/zipitz2.h b/include/configs/zipitz2.h new file mode 100644 index 0000000..a5a873b --- /dev/null +++ b/include/configs/zipitz2.h @@ -0,0 +1,259 @@ +/* + * Aeronix Zipit Z2 configuration file + * + * Copyright (C) 2009-2010 Marek Vasut <marek.vasut@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Board Configuration Options + */ +#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */ +#define CONFIG_ZIPITZ2 1 /* Zipit Z2 board */ + +#undef BOARD_LATE_INIT +#undef CONFIG_SKIP_RELOCATE_UBOOT +#undef CONFIG_USE_IRQ +#undef CONFIG_SKIP_LOWLEVEL_INIT + +/* + * Environment settings + */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR 0x40000 +#define CONFIG_ENV_SIZE 0x20000 + +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + CONFIG_STACKSIZE) +#define CONFIG_SYS_GBL_DATA_SIZE 512 + +#define CONFIG_BOOTCOMMAND \ + "if mmc init && fatload mmc 0 0xa0000000 uboot.script ; then " \ + "source 0xa0000000; " \ + "else " \ + "bootm 0x60000; " \ + "fi; " +#define CONFIG_BOOTARGS \ + "console=tty0 console=ttyS2,115200 fbcon=rotate:3" +#define CONFIG_TIMESTAMP +#define CONFIG_BOOTDELAY 2 /* Autoboot delay */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS + +#define CONFIG_LZMA /* LZMA compression support */ + +/* + * Serial Console Configuration + * STUART - the lower serial port on Colibri board + */ +#define CONFIG_PXA_SERIAL +#define CONFIG_STUART 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Bootloader Components Configuration + */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_NET +#define CONFIG_CMD_ENV +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_MMC +#define CONFIG_CMD_SPI + +/* + * MMC Card Configuration + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_PXA_MMC +#define CONFIG_SYS_MMC_BASE 0xF0000000 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_EXT2 +#define CONFIG_DOS_PARTITION +#endif + +/* + * SPI and LCD + */ +#ifdef CONFIG_CMD_SPI +#define CONFIG_SOFT_SPI +#define CONFIG_LCD +#define CONFIG_LMS283GF05 +#define CONFIG_VIDEO_LOGO +#define CONFIG_CMD_BMP +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) +#undef SPI_INIT + +#define SPI_DELAY udelay(10) +#define SPI_SDA(val) zipitz2_spi_sda(val) +#define SPI_SCL(val) zipitz2_spi_scl(val) +#define SPI_READ zipitz2_spi_read() +#ifndef __ASSEMBLY__ +void zipitz2_spi_sda(int); +void zipitz2_spi_scl(int); +unsigned char zipitz2_spi_read(void); +#endif +#endif + +/* + * KGDB + */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * HUSH Shell Configuration + */ +#define CONFIG_SYS_HUSH_PARSER 1 +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */ +#else +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#endif +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_DEVICE_NULLDEV 1 + +/* + * Clock Configuration + */ +#undef CONFIG_SYS_CLKS_IN_HZ +#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */ +#define CONFIG_SYS_CPUSPEED 0x190 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */ + +/* + * Stack sizes + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * DRAM Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* We have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ + +#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */ +#define CONFIG_SYS_DRAM_SIZE 0x02000000 /* 32 MB DRAM */ + +#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_DRAM_BASE + +/* + * NOR FLASH + */ +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ +#define PHYS_FLASH_SIZE 0x00800000 /* 8 MB */ +#define PHYS_FLASH_SECT_SIZE 0x00010000 /* 64 KB sectors */ +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 +#define CONFIG_SYS_MONITOR_LEN PHYS_FLASH_SECT_SIZE + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 256 + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 + +#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_LOCK_TOUT (2*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_UNLOCK_TOUT (2*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_PROTECTION + +/* + * GPIO settings + */ +#define CONFIG_SYS_GAFR0_L_VAL 0x02000140 +#define CONFIG_SYS_GAFR0_U_VAL 0x59188000 +#define CONFIG_SYS_GAFR1_L_VAL 0x63900002 +#define CONFIG_SYS_GAFR1_U_VAL 0xaaa03950 +#define CONFIG_SYS_GAFR2_L_VAL 0x0aaaaaaa +#define CONFIG_SYS_GAFR2_U_VAL 0x29000308 +#define CONFIG_SYS_GAFR3_L_VAL 0x54000000 +#define CONFIG_SYS_GAFR3_U_VAL 0x000000d5 +#define CONFIG_SYS_GPCR0_VAL 0x00000000 +#define CONFIG_SYS_GPCR1_VAL 0x00000020 +#define CONFIG_SYS_GPCR2_VAL 0x00000000 +#define CONFIG_SYS_GPCR3_VAL 0x00000000 +#define CONFIG_SYS_GPDR0_VAL 0xdafcee00 +#define CONFIG_SYS_GPDR1_VAL 0xffa3aaab +#define CONFIG_SYS_GPDR2_VAL 0x8fe1ffff +#define CONFIG_SYS_GPDR3_VAL 0x001b1f8a +#define CONFIG_SYS_GPSR0_VAL 0x06080400 +#define CONFIG_SYS_GPSR1_VAL 0x007f0000 +#define CONFIG_SYS_GPSR2_VAL 0x032a0000 +#define CONFIG_SYS_GPSR3_VAL 0x00000180 + +#define CONFIG_SYS_PSSR_VAL 0x30 + +/* + * Clock settings + */ +#define CONFIG_SYS_CKEN 0x00511220 +#define CONFIG_SYS_CCCR 0x00000190 + +/* + * Memory settings + */ +#define CONFIG_SYS_MSC0_VAL 0x2ffc38f8 +#define CONFIG_SYS_MSC1_VAL 0x0000ccd1 +#define CONFIG_SYS_MSC2_VAL 0x0000b884 +#define CONFIG_SYS_MDCNFG_VAL 0x08000ba9 +#define CONFIG_SYS_MDREFR_VAL 0x2011a01e +#define CONFIG_SYS_MDMRS_VAL 0x00000000 +#define CONFIG_SYS_FLYCNFG_VAL 0x00010001 +#define CONFIG_SYS_SXCNFG_VAL 0x40044004 + +/* + * PCMCIA and CF Interfaces + */ +#define CONFIG_SYS_MECR_VAL 0x00000001 +#define CONFIG_SYS_MCMEM0_VAL 0x00014307 +#define CONFIG_SYS_MCMEM1_VAL 0x00014307 +#define CONFIG_SYS_MCATT0_VAL 0x0001c787 +#define CONFIG_SYS_MCATT1_VAL 0x0001c787 +#define CONFIG_SYS_MCIO0_VAL 0x0001430f +#define CONFIG_SYS_MCIO1_VAL 0x0001430f + +#endif /* __CONFIG_H */ diff --git a/include/environment.h b/include/environment.h index 203f731..fbccf6a 100644 --- a/include/environment.h +++ b/include/environment.h @@ -74,15 +74,24 @@ #endif /* CONFIG_ENV_IS_IN_FLASH */ #if defined(CONFIG_ENV_IS_IN_NAND) -# ifndef CONFIG_ENV_OFFSET -# error "Need to define CONFIG_ENV_OFFSET when using CONFIG_ENV_IS_IN_NAND" -# endif +# if defined(CONFIG_ENV_OFFSET_OOB) +# ifdef CONFIG_ENV_OFFSET_REDUND +# error "CONFIG_ENV_OFFSET_REDUND is not supported when CONFIG_ENV_OFFSET_OOB" +# error "is set" +# endif +extern unsigned long nand_env_oob_offset; +# define CONFIG_ENV_OFFSET nand_env_oob_offset +# else +# ifndef CONFIG_ENV_OFFSET +# error "Need to define CONFIG_ENV_OFFSET when using CONFIG_ENV_IS_IN_NAND" +# endif +# ifdef CONFIG_ENV_OFFSET_REDUND +# define CONFIG_SYS_REDUNDAND_ENVIRONMENT +# endif +# endif /* CONFIG_ENV_OFFSET_OOB */ # ifndef CONFIG_ENV_SIZE # error "Need to define CONFIG_ENV_SIZE when using CONFIG_ENV_IS_IN_NAND" # endif -# ifdef CONFIG_ENV_OFFSET_REDUND -# define CONFIG_SYS_REDUNDAND_ENVIRONMENT -# endif #endif /* CONFIG_ENV_IS_IN_NAND */ #if defined(CONFIG_ENV_IS_IN_MG_DISK) diff --git a/include/fdt_support.h b/include/fdt_support.h index 9a453af..fc16159 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -59,7 +59,7 @@ void fdt_fixup_dr_usb(void *blob, bd_t *bd); static inline void fdt_fixup_dr_usb(void *blob, bd_t *bd) {} #endif /* CONFIG_HAS_FSL_DR_USB */ -#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC83xx) +#if defined(CONFIG_SYS_FSL_SEC_COMPAT) void fdt_fixup_crypto_node(void *blob, int sec_rev); #else static inline void fdt_fixup_crypto_node(void *blob, int sec_rev) {} diff --git a/include/lcd.h b/include/lcd.h index 1f85daa..cd9d49d 100644 --- a/include/lcd.h +++ b/include/lcd.h @@ -87,7 +87,7 @@ typedef struct vidinfo { u_char vl_wbf; /* Wait between frames */ } vidinfo_t; -#elif defined CONFIG_PXA250 +#elif defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS /* * PXA LCD DMA descriptor */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 5214911..ba6cdf1 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007, 2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -65,6 +65,7 @@ #define PARTID_NO_E(spridr) ((spridr & 0xFFFE0000) >> 16) #define SPR_FAMILY(spridr) ((spridr & 0xFFF00000) >> 20) +#define SPR_8308 0x8100 #define SPR_831X_FAMILY 0x80B #define SPR_8311 0x80B2 #define SPR_8313 0x80B0 @@ -115,8 +116,9 @@ #define SPCR_TSEC2EP 0x00000003 /* TSEC2 emergency priority */ #define SPCR_TSEC2EP_SHIFT (31-31) -#elif defined(CONFIG_MPC831x) || defined(CONFIG_MPC837x) -/* SPCR bits - MPC831x and MPC837x specific */ +#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ + defined(CONFIG_MPC837x) +/* SPCR bits - MPC8308, MPC831x and MPC837x specific */ #define SPCR_TSECDP 0x00003000 /* TSEC data priority */ #define SPCR_TSECDP_SHIFT (31-19) #define SPCR_TSECBDP 0x00000C00 /* TSEC buffer descriptor priority */ @@ -473,7 +475,7 @@ #define HRCWL_CE_TO_PLL_1X30 0x0000001E #define HRCWL_CE_TO_PLL_1X31 0x0000001F -#elif defined(CONFIG_MPC8315) +#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC8315) #define HRCWL_SVCOD 0x30000000 #define HRCWL_SVCOD_SHIFT 28 #define HRCWL_SVCOD_DIV_2 0x00000000 @@ -541,7 +543,8 @@ #define HRCWH_ROM_LOC_LOCAL_16BIT 0x00600000 #define HRCWH_ROM_LOC_LOCAL_32BIT 0x00700000 -#if defined(CONFIG_MPC831x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ + defined(CONFIG_MPC837x) #define HRCWH_ROM_LOC_NAND_SP_8BIT 0x00100000 #define HRCWH_ROM_LOC_NAND_SP_16BIT 0x00200000 #define HRCWH_ROM_LOC_NAND_LP_8BIT 0x00500000 @@ -592,7 +595,8 @@ /* RSR - Reset Status Register */ -#if defined(CONFIG_MPC831x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ + defined(CONFIG_MPC837x) #define RSR_RSTSRC 0xF0000000 /* Reset source */ #define RSR_RSTSRC_SHIFT 28 #else @@ -734,8 +738,8 @@ #define SCCR_USBDRCM_2 0x00200000 #define SCCR_USBDRCM_3 0x00300000 -#elif defined(CONFIG_MPC8315) -/* SCCR bits - MPC8315 specific */ +#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC8315) +/* SCCR bits - MPC8315/MPC8308 specific */ #define SCCR_TSEC1CM 0xc0000000 #define SCCR_TSEC1CM_SHIFT 30 #define SCCR_TSEC1CM_0 0x00000000 @@ -750,6 +754,13 @@ #define SCCR_TSEC2CM_2 0x20000000 #define SCCR_TSEC2CM_3 0x30000000 +#define SCCR_SDHCCM 0x0c000000 +#define SCCR_SDHCCM_SHIFT 26 +#define SCCR_SDHCCM_0 0x00000000 +#define SCCR_SDHCCM_1 0x04000000 +#define SCCR_SDHCCM_2 0x08000000 +#define SCCR_SDHCCM_3 0x0c000000 + #define SCCR_USBDRCM 0x00c00000 #define SCCR_USBDRCM_SHIFT 22 #define SCCR_USBDRCM_0 0x00000000 diff --git a/include/mpc85xx.h b/include/mpc85xx.h index a4d4d65..2495b99 100644 --- a/include/mpc85xx.h +++ b/include/mpc85xx.h @@ -6,8 +6,6 @@ #ifndef __MPC85xx_H__ #define __MPC85xx_H__ -#include <asm/fsl_lbc.h> - /* define for common ppc_asm.tmpl */ #define EXC_OFF_SYS_RESET 0x100 /* System reset */ #define _START_OFFSET 0 diff --git a/include/nand.h b/include/nand.h index 2a81597..8bdf419 100644 --- a/include/nand.h +++ b/include/nand.h @@ -130,3 +130,12 @@ void board_nand_select_device(struct nand_chip *nand, int chip); __attribute__((noreturn)) void nand_boot(void); #endif + +#ifdef CONFIG_ENV_OFFSET_OOB +#define ENV_OOB_MARKER 0x30425645 /*"EVB0" in little-endian -- offset is stored + as block number*/ +#define ENV_OOB_MARKER_OLD 0x30564e45 /*"ENV0" in little-endian -- offset is + stored as byte number */ +#define ENV_OFFSET_SIZE 8 +int get_nand_env_oob(nand_info_t *nand, unsigned long *result); +#endif diff --git a/include/netdev.h b/include/netdev.h index 882642a..94eedfe 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -43,12 +43,14 @@ int cpu_eth_init(bd_t *bis); /* Driver initialization prototypes */ int altera_tse_initialize(u8 dev_num, int mac_base, int sgdma_rx_base, int sgdma_tx_base); +int ax88180_initialize(bd_t *bis); int au1x00_enet_initialize(bd_t*); int at91emac_register(bd_t *bis, unsigned long iobase); int bfin_EMAC_initialize(bd_t *bis); int cs8900_initialize(u8 dev_num, int base_addr); int dc21x4x_initialize(bd_t *bis); int davinci_emac_initialize(void); +int designware_initialize(u32 id, ulong base_addr, u32 phy_addr); int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr); int e1000_initialize(bd_t *bis); int eepro100_initialize(bd_t *bis); @@ -61,7 +63,6 @@ int ftmac100_initialize(bd_t *bits); int greth_initialize(bd_t *bis); void gt6426x_eth_initialize(bd_t *bis); int inca_switch_initialize(bd_t *bis); -int kirkwood_egiga_initialize(bd_t *bis); int lan91c96_initialize(u8 dev_num, int base_addr); int macb_eth_initialize(int id, void *regs, unsigned int phy_addr); int mcdmafec_initialize(bd_t *bis); @@ -70,6 +71,7 @@ int mpc512x_fec_initialize(bd_t *bis); int mpc5xxx_fec_initialize(bd_t *bis); int mpc8220_fec_initialize(bd_t *bis); int mpc82xx_scc_enet_initialize(bd_t *bis); +int mvgbe_initialize(bd_t *bis); int natsemi_initialize(bd_t *bis); int npe_initialize(bd_t *bis); int ns8382x_initialize(bd_t *bis); diff --git a/include/status_led.h b/include/status_led.h index 9dbf01f..f213595 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -346,9 +346,6 @@ void status_led_set (int led, int state); #elif defined(CONFIG_NIOS2) /* XXX empty just to avoid the error */ /************************************************************************/ -#elif defined(CONFIG_BLACKFIN) -/* XXX empty just to avoid the error */ -/************************************************************************/ #elif defined(CONFIG_V38B) # define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */ |