diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/commproc.h | 62 | ||||
| -rw-r--r-- | include/configs/v37.h | 381 | ||||
| -rw-r--r-- | include/flash.h | 5 | ||||
| -rw-r--r-- | include/version.h | 2 |
4 files changed, 430 insertions, 20 deletions
diff --git a/include/commproc.h b/include/commproc.h index 42db998..159c294 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -1100,6 +1100,34 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */ #endif /* CONFIG_MHPC */ +/*** NETVIA *******************************************************/ + +#if defined(CONFIG_NETVIA) +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC2 use. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ +#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ + +#define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */ +#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */ + +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to + * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002f00) + +#endif /* CONFIG_NETVIA */ + /*** RPXCLASSIC *****************************************************/ #ifdef CONFIG_RPXCLASSIC @@ -1309,31 +1337,27 @@ typedef struct scc_enet { # endif /* CONFIG_FEC_ENET */ #endif /* CONFIG_TQM860L, CONFIG_TQM855L */ -#if defined(CONFIG_NETVIA) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. +/*** V37 **********************************************************/ + +#ifdef CONFIG_V37 +/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of + * this may be unique to the Marel V37 configuration. + * Note TENA is on Port B. */ #define PROFF_ENET PROFF_SCC2 #define CPM_CR_ENET CPM_CR_CH_SCC2 #define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ - -#define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */ -#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ +#define PA_ENET_RXD ((ushort)0x0004) +#define PA_ENET_TXD ((ushort)0x0008) +#define PA_ENET_TCLK ((ushort)0x0400) +#define PA_ENET_RCLK ((ushort)0x0200) +#define PB_ENET_TENA ((uint)0x00002000) +#define PC_ENET_CLSN ((ushort)0x0040) +#define PC_ENET_RENA ((ushort)0x0080) -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ #define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002f00) - -#endif /* CONFIG_NETVIA */ +#define SICR_ENET_CLKRT ((uint)0x00002e00) +#endif /* CONFIG_V37 */ /*********************************************************************/ diff --git a/include/configs/v37.h b/include/configs/v37.h new file mode 100644 index 0000000..f527440 --- /dev/null +++ b/include/configs/v37.h @@ -0,0 +1,381 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_V37 1 /* ...on a Marel V37 board */ + +#define CONFIG_LCD +#define CONFIG_SHARP_LQ084V1DG21 +#undef CONFIG_LCD_LOGO + +/*----------------------------------------------------------------------------- + * I2C Configuration + *----------------------------------------------------------------------------- + */ +#define CONFIG_I2C 1 +#define CFG_I2C_SLAVE 0x2 + +#define CONFIG_8xx_CONS_SMC1 1 +#undef CONFIG_8xx_CONS_SMC2 /* Console is on SMC2 */ +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 /* console baudrate = 115kbps */ +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_BOOTCOMMAND \ + "tftpboot; " \ + "setenv bootargs console=tty0 " \ + "root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_DATE ) + + +/* Flash banks JFFS2 should use */ +#define CFG_JFFS2_FIRST_BANK 1 +#define CFG_JFFS2_NUM_BANKS 1 + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE0 0x40000000 +#define CFG_FLASH_BASE1 0x60000000 +#define CFG_FLASH_BASE CFG_FLASH_BASE1 + +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE0 +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_NVRAM 1 +#define CFG_ENV_ADDR 0x80000000/* Address of Environment */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +#define CFG_ENV_OFFSET 0 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR 0xFFFFFF88 +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_FRC | SIUMCR_GB5E) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) +/* +#define CFG_PISCR (PISCR_PS | PISCR_PITF) +*/ + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! + */ +/* up to 50 MHz we use a 1:1 clock */ +#define CFG_PLPRCR ( (1524 << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TMIST | PLPRCR_TEXPS ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +/* up to 50 MHz we use a 1:1 clock */ +#define CFG_SCCR (SCCR_COM00 | SCCR_TBS) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_PCMCIA /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0x0082000F +/*#define CFG_DER 0*/ + +/* + * Init Memory Controller: + * + * BR0 and OR0 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */ + +#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */ + +#define CFG_OR_TIMING_FLASH 0xF56 + +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V) + +#define CFG_OR5_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR5_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V) + +/* + * BR1 and OR1 (Battery backed SRAM) + */ +#define CFG_BR1_PRELIM 0x80000401 +#define CFG_OR1_PRELIM 0xFFC00736 + +/* + * BR2 and OR2 (SDRAM) + */ +#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB */ + +#define CFG_OR_TIMING_SDRAM 0x00000A00 + +#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* Marel V37 mem setting */ + +#define CFG_BR3_CAN 0xC0000401 +#define CFG_OR3_CAN 0xFFFF0724 + +/* +#define CFG_BR3_PRELIM 0xFA400001 +#define CFG_OR3_PRELIM 0xFFFF8910 +#define CFG_BR4_PRELIM 0xFA000401 +#define CFG_OR4_PRELIM 0xFFFE0970 +*/ + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */ + +/* + * Refresh clock Prescalar + */ +#define CFG_MPTPR MPTPR_PTP_DIV16 + +/* + * MAMR settings for SDRAM + */ + +/* 10 column SDRAM */ +#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \ + MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + + +#endif /* __CONFIG_H */ diff --git a/include/flash.h b/include/flash.h index 3150e3d..b4c8bad 100644 --- a/include/flash.h +++ b/include/flash.h @@ -111,6 +111,7 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot); #define INTEL_MANUFACT 0x00890089 /* INTEL manuf. ID in D23..D16, D7..D0 */ #define INTEL_ALT_MANU 0x00B000B0 /* alternate INTEL namufacturer ID */ #define MX_MANUFACT 0x00C200C2 /* MXIC manuf. ID in D23..D16, D7..D0 */ +#define TOSH_MANUFACT 0x00980098 /* TOSHIBA manuf. ID in D23..D16, D7..D0 */ /* Micron Technologies (INTEL compat.) */ #define MT_ID_28F400_T 0x44704470 /* 28F400B3 ID ( 4 M, top boot sector) */ @@ -206,6 +207,9 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot); #define SHARP_ID_28F008SC 0xA6A6A6A6 /* LH28F008SCT-L12 1Mx8, 16 64k blocks */ /* LH28F008SCR-L85 1Mx8, 16 64k blocks */ +#define TOSH_ID_FVT160 0xC2 /* TC58FVT160 ID (16 M, top ) */ +#define TOSH_ID_FVB160 0x43 /* TC58FVT160 ID (16 M, bottom ) */ + /*----------------------------------------------------------------------- * Internal FLASH identification codes * @@ -301,6 +305,7 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot); #define FLASH_MAN_BM 0x00020000 /* Bright Microelectronics */ #define FLASH_MAN_MX 0x00030000 /* MXIC */ #define FLASH_MAN_STM 0x00040000 +#define FLASH_MAN_TOSH 0x00050000 /* Toshiba */ #define FLASH_MAN_SST 0x00100000 #define FLASH_MAN_INTEL 0x00300000 #define FLASH_MAN_MT 0x00400000 diff --git a/include/version.h b/include/version.h index b501028..5249f2a 100644 --- a/include/version.h +++ b/include/version.h @@ -24,6 +24,6 @@ #ifndef __VERSION_H__ #define __VERSION_H__ -#define U_BOOT_VERSION "U-Boot 0.2.1" +#define U_BOOT_VERSION "U-Boot 0.2.2" #endif /* __VERSION_H__ */ |