diff options
Diffstat (limited to 'include')
30 files changed, 546 insertions, 110 deletions
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index 7b82c43..a959940 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -296,13 +296,13 @@ /* * CS4 on Local Bus, to PIB */ -#define CONFIG_SYS_BR4_PRELIM 0xf8010801 /* CS4 base address at 0xf8010000 */ +#define CONFIG_SYS_BR4_PRELIM 0xf8008801 /* CS4 base address at 0xf8008000 */ #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* * CS5 on Local Bus, to PIB */ -#define CONFIG_SYS_BR5_PRELIM 0xf8008801 /* CS5 base address at 0xf8008000 */ +#define CONFIG_SYS_BR5_PRELIM 0xf8010801 /* CS5 base address at 0xf8010000 */ #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 850665a..5c5be0c 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -242,9 +242,10 @@ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND) \ - || defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) +#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \ + defined(CONFIG_RAMBOOT_SPIFLASH) #define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC #else #undef CONFIG_SYS_RAMBOOT #endif diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index c7973b4..9620fd0 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -203,8 +203,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND) +#if defined(CONFIG_RAMBOOT_NAND) #define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC #else #undef CONFIG_SYS_RAMBOOT #endif diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 692c811..1ee95ae 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -202,6 +202,7 @@ #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_HWCONFIG /* enable hwconfig */ #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ #ifdef CONFIG_PHYS_64BIT diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 610f3ed..2dfee3d 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -201,9 +201,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND) \ - || defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) +#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \ + defined(CONFIG_RAMBOOT_SPIFLASH) #define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC #else #undef CONFIG_SYS_RAMBOOT #endif @@ -436,14 +437,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -/* TBI PHY configuration for SGMII mode */ -#define CONFIG_TSEC_TBICR_SETTINGS ( \ - TBICR_PHY_RESET \ - | TBICR_ANEG_ENABLE \ - | TBICR_FULL_DUPLEX \ - | TBICR_SPEED1_SET \ - ) - #endif /* CONFIG_TSEC_ENET */ /* diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index 9a9ba88..70e8f07 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -163,6 +163,7 @@ #define CONFIG_DRIVER_OMAP34XX_I2C 1 #undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS /* * Board NAND Info. */ @@ -330,4 +331,10 @@ extern unsigned int boot_flash_sec; extern unsigned int boot_flash_type; #endif +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 +#define CONFIG_SYS_INIT_RAM_SIZE 0x800 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) #endif /* __CONFIG_H */ diff --git a/include/configs/aria.h b/include/configs/aria.h index b3ca8d2..3a60de0 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -49,7 +49,6 @@ #define CONFIG_E300 1 /* E300 Family */ #define CONFIG_MPC512X 1 /* MPC512X family */ #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ -#define CONFIG_FSL_DIU_LOGO_BMP 1 /* Don't include FSL DIU binary bmp */ #define CONFIG_SYS_TEXT_BASE 0xFFF00000 diff --git a/include/configs/at91rm9200ek.h b/include/configs/at91rm9200ek.h index 14559f5..810023a 100644 --- a/include/configs/at91rm9200ek.h +++ b/include/configs/at91rm9200ek.h @@ -33,6 +33,20 @@ #include <asm/sizes.h> /* + * set some initial configurations depending on configure target + * + * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 + * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel + * initialisation was done by some preloader + */ +#ifdef CONFIG_RAMBOOT +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SYS_TEXT_BASE 0x20100000 +#else +#define CONFIG_SYS_TEXT_BASE 0x10000000 +#endif + +/* * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz * AT91C_MAIN_CLOCK is the frequency of PLLA output * AT91C_MASTER_CLOCK is the peripherial clock @@ -57,6 +71,8 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG +#define CONFIG_AT91FAMILY + /* * Memory Configuration */ @@ -90,7 +106,7 @@ #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ -#define CONFIG_SYS_SDRAM1 CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ +#define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ diff --git a/include/configs/atngw100.h b/include/configs/atngw100.h index 83056b6..92491ca 100644 --- a/include/configs/atngw100.h +++ b/include/configs/atngw100.h @@ -104,8 +104,6 @@ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY -#define CONFIG_DOS_PARTITION 1 - /* * Command line configuration. */ diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h index e1b1db1..45214fa 100644 --- a/include/configs/davinci_dvevm.h +++ b/include/configs/davinci_dvevm.h @@ -50,7 +50,7 @@ /*=======*/ #define DV_EVM #define CONFIG_SYS_NAND_SMALLPAGE -#define CONFIG_SYS_USE_NOR +#define CONFIG_SYS_USE_NAND #define CONFIG_DISPLAY_CPUINFO /*===================*/ /* SoC Configuration */ @@ -78,6 +78,7 @@ #define CONFIG_STACKSIZE (256*1024) /* regular stack */ #define PHYS_SDRAM_1 0x80000000 /* DDR Start */ #define PHYS_SDRAM_1_SIZE 0x10000000 /* DDR size 256MB */ + #define DDR_8BANKS /* 8-bank DDR2 (256MB) */ /*====================*/ /* Serial Driver info */ @@ -228,11 +229,13 @@ #define CONFIG_PREBOOT "usb start" #endif #endif -/*=======================*/ -/* KGDB support (if any) */ -/*=======================*/ -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ -#endif + +#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/igep0030.h b/include/configs/igep0030.h index d61793c..1325bfa 100644 --- a/include/configs/igep0030.h +++ b/include/configs/igep0030.h @@ -110,6 +110,7 @@ #define CONFIG_MTD_DEVICE #undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#undef CONFIG_CMD_NFS /* nfs */ #undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ #undef CONFIG_CMD_IMLS /* List all found images */ diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h index 6ed9e75..16e2ec6 100644 --- a/include/configs/mimc200.h +++ b/include/configs/mimc200.h @@ -109,8 +109,6 @@ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY -#define CONFIG_DOS_PARTITION 1 - /* * Command line configuration. */ diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index f98438d..b4e5738 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -216,8 +216,9 @@ */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_ENV_SIZE (8 * 1024) +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index 84b2986..5bdb3fd 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -330,7 +330,11 @@ extern unsigned int boot_flash_type; * Support for relocation */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 +#define CONFIG_SYS_INIT_RAM_SIZE 0x800 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) /* * Define the board revision statically diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h index a5eb648..4708981 100644 --- a/include/configs/omap3_sdp3430.h +++ b/include/configs/omap3_sdp3430.h @@ -309,6 +309,12 @@ #define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack */ #endif +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 +#define CONFIG_SYS_INIT_RAM_SIZE 0x800 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) /* * SDRAM Memory Map */ diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index d9e8ea0..f7d0652 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -236,6 +236,12 @@ #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ /* load address */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 +#define CONFIG_SYS_INIT_RAM_SIZE 0x800 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) /* * OMAP3 has 12 GP timers, they can be driven by the system clock * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h index 41abe04..7377933 100644 --- a/include/configs/omap3_zoom2.h +++ b/include/configs/omap3_zoom2.h @@ -188,6 +188,12 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "usbtty=cdc_acm\0" \ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 +#define CONFIG_SYS_INIT_RAM_SIZE 0x800 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) /* * Miscellaneous configurable options */ diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h index bdd330a..9a8bb73 100644 --- a/include/configs/omap4_sdp4430.h +++ b/include/configs/omap4_sdp4430.h @@ -140,6 +140,7 @@ /* Disabled commands */ #undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ #undef CONFIG_CMD_IMLS /* List all found images */ diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h index 7fcc9ba..26e5049 100644 --- a/include/configs/pm9261.h +++ b/include/configs/pm9261.h @@ -45,6 +45,8 @@ #define CONFIG_PM9261 1 /* on a Ronetix PM9261 Board */ #define CONFIG_ARCH_CPU_INIT #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ +#define CONFIG_SYS_TEXT_BASE 0 +#define CONFIG_AT91FAMILY /* clocks */ /* CKGR_MOR - enable main osc. */ @@ -201,6 +203,7 @@ #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_IMLS +#define CONFIG_CMD_CACHE #define CONFIG_CMD_PING 1 #define CONFIG_CMD_DHCP 1 #define CONFIG_CMD_NAND 1 @@ -370,6 +373,10 @@ #define CONFIG_SYS_MALLOC_LEN \ ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000) +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + #define CONFIG_STACKSIZE (32 * 1024) /* regular stack */ #ifdef CONFIG_USE_IRQ diff --git a/include/configs/pm9263.h b/include/configs/pm9263.h index 619af2d..96e12f2 100644 --- a/include/configs/pm9263.h +++ b/include/configs/pm9263.h @@ -44,6 +44,8 @@ #define CONFIG_PM9263 1 /* on a Ronetix PM9263 Board */ #define CONFIG_ARCH_CPU_INIT #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ +#define CONFIG_SYS_TEXT_BASE 0 +#define CONFIG_AT91FAMILY /* clocks */ #define CONFIG_SYS_MOR_VAL \ @@ -212,6 +214,7 @@ #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_IMLS +#define CONFIG_CMD_CACHE #define CONFIG_CMD_PING 1 #define CONFIG_CMD_DHCP 1 #define CONFIG_CMD_NAND 1 @@ -401,6 +404,10 @@ */ #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000) +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + #define CONFIG_STACKSIZE (32 * 1024) /* regular stack */ #ifdef CONFIG_USE_IRQ diff --git a/include/configs/pm9g45.h b/include/configs/pm9g45.h index 3ed6b56..ec51ccf 100644 --- a/include/configs/pm9g45.h +++ b/include/configs/pm9g45.h @@ -39,6 +39,8 @@ /* ARM asynchronous clock */ #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ #define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_TEXT_BASE 0x73f00000 +#define CONFIG_AT91FAMILY #define CONFIG_ARCH_CPU_INIT @@ -79,6 +81,7 @@ #undef CONFIG_CMD_FPGA #undef CONFIG_CMD_IMLS +#define CONFIG_CMD_CACHE #define CONFIG_CMD_PING 1 #define CONFIG_CMD_DHCP 1 #define CONFIG_CMD_NAND 1 @@ -175,6 +178,10 @@ #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\ 0x1000) +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + #define CONFIG_STACKSIZE (32*1024) /* regular stack */ #ifdef CONFIG_USE_IRQ diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h index 3416cb8..802416f 100644 --- a/include/configs/r7780mp.h +++ b/include/configs/r7780mp.h @@ -154,7 +154,6 @@ #define CONFIG_RTL8169 */ /* AX88796L Support(NE2000 base chip) */ -#define CONFIG_DRIVER_NE2000 #define CONFIG_DRIVER_AX88796L #define CONFIG_DRIVER_NE2000_BASE 0xA4100000 #endif diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h index 541aec0..f53e798 100644 --- a/include/configs/s5p_goni.h +++ b/include/configs/s5p_goni.h @@ -217,4 +217,6 @@ #define CONFIG_DOS_PARTITION 1 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) + #endif /* __CONFIG_H */ diff --git a/include/configs/smdkc100.h b/include/configs/smdkc100.h index e36b262..fb8b43c 100644 --- a/include/configs/smdkc100.h +++ b/include/configs/smdkc100.h @@ -231,6 +231,8 @@ #define CONFIG_DOS_PARTITION 1 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) + /* * Ethernet Contoller driver */ diff --git a/include/configs/top9000.h b/include/configs/top9000.h new file mode 100644 index 0000000..ff3933b --- /dev/null +++ b/include/configs/top9000.h @@ -0,0 +1,314 @@ +/* + * (C) Copyright 2010 + * Reinhard Meyer, EMK Elektronik, reinhard.meyer@emk-elektronik.de + * + * Configuation settings for the TOP9000 CPU module with AT91SAM9XE. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +/* + * top9000 with at91sam9xe256 or at91sam9xe512 + * + * Initial Bootloader is in embedded flash. + * Vital Product Data, U-Boot Environment are in I2C-EEPROM. + * U-Boot is in embedded flash, a backup U-Boot can be in NAND flash. + * kernel and file system are either in NAND flash or on a micro SD card. + * NAND flash is optional. + * I2C EEPROM is never optional. + * SPI FRAM is optional. + * SPI ENC28J60 is optional. + * 16 or 32 bit wide SDRAM. + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Warning: changing CONFIG_SYS_TEXT_BASE requires + * adapting the initial boot program + */ +#define CONFIG_SYS_TEXT_BASE 0x21f00000 /* 31 MB into RAM */ + +/* Command line configuration */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG +#define CONFIG_CMD_ASKENV +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_PROMPT "TOP9000> " +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CMD_BDI +#define CONFIG_CMD_CACHE + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz xtal */ +#define CONFIG_SYS_HZ 1000 + +/* SoC */ +#define CONFIG_ARM926EJS /* ARM926EJS Core */ +#define CONFIG_AT91FAMILY /* it's a member of AT91 */ +#define CONFIG_AT91SAM9260 /* Atmel AT91SAM9260 based SoC */ +#define CONFIG_AT91SAM9XE + +/* Misc CPU related */ +#define CONFIG_AT91_LEGACY +#define CONFIG_ARCH_CPU_INIT +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_AT91RESET_EXTRST /* assert external reset */ + +/* general purpose I/O */ +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART3 /* USART 3 is DBGU !!! */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } + +/* SD/MMC card */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#define CONFIG_SYS_MMC_CD_PIN AT91_PIN_PC9 +#define CONFIG_CMD_MMC + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_SYS_PHY_ID 1 +#define CONFIG_RMII +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 20 + +/* real time clock */ +#define CONFIG_RTC_AT91SAM9_RTT +#define CONFIG_CMD_DATE + +#if defined(CONFIG_AT91SAM9XE) +/* + * NOR flash - use embedded flash of SAM9XE256/512 + * U-Boot will not fit into 128K ! + * 2010.09 will not fit into 256K with all options enabled ! + * + * Layout: + * 16kB 1st Bootloader + * Rest U-Boot + * the first sector (16kB) of EFLASH cannot be unprotected + * with u-boot commands + */ +# define CONFIG_AT91_EFLASH +# define CONFIG_SYS_FLASH_BASE 0x200000 +# define CONFIG_SYS_MAX_FLASH_SECT 32 +# define CONFIG_SYS_MAX_FLASH_BANKS 1 +# define CONFIG_SYS_FLASH_PROTECTION +# define CONFIG_EFLASH_PROTSECTORS 1 /* protect first sector */ +#endif + +/* SPI */ +#define CONFIG_ATMEL_SPI +#define CONFIG_CMD_SPI + +/* RAMTRON FRAM */ +#define CONFIG_CMD_SF +#define CONFIG_ATMEL_SPI0 /* SPI used for FRAM is SPI0 */ +#define FRAM_SPI_BUS 0 +#define FRAM_CS_NUM 0 +#define CONFIG_SPI_FLASH /* RAMTRON FRAM on SPI bus */ +#define CONFIG_SPI_FRAM_RAMTRON +#define CONFIG_SF_DEFAULT_SPEED 1000000 /* be conservative here... */ +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC "FM25H20" + +/* Microchip ENC28J60 (second LAN) */ +#if defined(CONFIG_EVAL9000) +# define CONFIG_ENC28J60 +# define CONFIG_ATMEL_SPI1 /* SPI used for ENC28J60 is SPI1 */ +# define ENC_SPI_BUS 1 +# define ENC_CS_NUM 0 +# define ENC_SPI_CLOCK 1000000 +#endif /* CONFIG_EVAL9000 */ + +/* + * SDRAM: 1 bank, min 32, max 128 MB + * Initialized before u-boot gets started. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x20000000 +#define CONFIG_SYS_SDRAM_SIZE 0x08000000 +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END 0x21e00000 +#define CONFIG_SYS_LOAD_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x01000000) +/* + * Initial stack pointer: 16k - GENERATED_GBL_DATA_SIZE in internal SRAM, + * leaving the correct space for initial global data structure above + * that address while providing maximum stack area below. + */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (0x00300000 + 0x4000 - GENERATED_GBL_DATA_SIZE) + +/* + * NAND flash: 256 MB (optional) + * + * Layout: + * 640kB: u-boot (includes space for spare sectors, handled by + * initial loader) + * 2MB: kernel + * rest: file system + */ +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_DBW_8 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 +#define CONFIG_CMD_NAND + +/* USB */ +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "top9000" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_USB + +/* I2C support must always be enabled */ +#define CONFIG_SOFT_I2C +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_I2C_MULTI_BUS +#define I2C0_PORT AT91_PIO_PORTA +#define SDA0_PIN 23 +#define SCL0_PIN 24 +#define I2C1_PORT AT91_PIO_PORTB +#define SDA1_PIN 12 +#define SCL1_PIN 13 +#define I2C_SOFT_DECLARATIONS void iic_init(void);\ + int iic_read(void);\ + void iic_sda(int);\ + void iic_scl(int); +#define I2C_ACTIVE +#define I2C_TRISTATE +#define I2C_INIT iic_init() +#define I2C_READ iic_read() +#define I2C_SDA(bit) iic_sda(bit) +#define I2C_SCL(bit) iic_scl(bit) +#define I2C_DELAY udelay(3) +/* EEPROM configuration */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_SIZE 0x2000 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +/* later: #define CONFIG_I2C_ENV_EEPROM_BUS 0 */ +/* ENV is always in I2C-EEPROM */ +#define CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_OFFSET 0x1000 +#define CONFIG_ENV_SIZE 0x0f00 +/* VPD settings */ +#define CONFIG_SYS_I2C_FACT_ADDR 0x57 +#define CONFIG_SYS_FACT_OFFSET 0x1F00 +#define CONFIG_SYS_FACT_SIZE 0x0100 +/* later: #define CONFIG_MISC_INIT_R */ +/* define the next only if you want to allow users to enter VPD data */ +#define CONFIG_SYS_FACT_ENTRY +#ifndef __ASSEMBLY__ +extern void read_factory_r(void); +#endif + +/* + * Only interrupt autoboot if <space> is pressed. Otherwise, garbage + * data on the serial line may interrupt the boot sequence. + */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * add filesystem commands if we have at least 1 storage + * media with filesystem + */ +#if defined(CONFIG_NAND_ATMEL) \ + || defined(CONFIG_USB_ATMEL) \ + || defined(CONFIG_MMC) +# define CONFIG_DOS_PARTITION +# define CONFIG_CMD_FAT +# define CONFIG_CMD_EXT2 +/* later: #define CONFIG_CMD_JFFS2 */ +#endif + +/* add NET commands if we have at least 1 LAN */ +#if defined(CONFIG_MACB) || defined(CONFIG_ENC28J60) +# define CONFIG_CMD_PING +# define CONFIG_CMD_DHCP +# define CONFIG_CMD_MII +/* is this really needed ? */ +# define CONFIG_RESET_PHY_R +/* BOOTP options */ +# define CONFIG_BOOTP_BOOTFILESIZE +# define CONFIG_BOOTP_BOOTPATH +# define CONFIG_BOOTP_GATEWAY +# define CONFIG_BOOTP_HOSTNAME +#endif + +/* linux in NAND flash */ +#define CONFIG_BOOTCOUNT_LIMIT 1 +#define CONFIG_BOOTCOMMAND \ + "nand read 0x21000000 0xA0000 0x200000; bootm" +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 " \ + "root=/dev/mtdblock2 " \ + "mtdparts=atmel_nand:" \ + "640k(uboot)ro," \ + "2M(linux)," \ + "16M(root)," \ + "-(rest) " \ + "rw "\ + "rootfstype=jffs2" + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN \ + ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) +#define CONFIG_STACKSIZE (32*1024) +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif + diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h index e0a1fa4..a74766d 100644 --- a/include/configs/xpedite537x.h +++ b/include/configs/xpedite537x.h @@ -375,6 +375,16 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ #define CONFIG_ETHPRIME "eTSEC2" +/* + * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force + * 1000mbps SGMII link + */ +#define CONFIG_TSEC_TBICR_SETTINGS ( \ + TBICR_PHY_RESET \ + | TBICR_FULL_DUPLEX \ + | TBICR_SPEED1_SET \ + ) + #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "eTSEC1" #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h index 42d1f69..a051913 100644 --- a/include/configs/xpedite550x.h +++ b/include/configs/xpedite550x.h @@ -345,6 +345,16 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ #define CONFIG_ETHPRIME "eTSEC2" +/* + * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force + * 1000mbps SGMII link + */ +#define CONFIG_TSEC_TBICR_SETTINGS ( \ + TBICR_PHY_RESET \ + | TBICR_FULL_DUPLEX \ + | TBICR_SPEED1_SET \ + ) + #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "eTSEC1" #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) diff --git a/include/linux/mii.h b/include/linux/mii.h index 7c63095..6e7ffab 100644 --- a/include/linux/mii.h +++ b/include/linux/mii.h @@ -10,98 +10,132 @@ /* Generic MII registers. */ -#define MII_BMCR 0x00 /* Basic mode control register */ -#define MII_BMSR 0x01 /* Basic mode status register */ -#define MII_PHYSID1 0x02 /* PHYS ID 1 */ -#define MII_PHYSID2 0x03 /* PHYS ID 2 */ -#define MII_ADVERTISE 0x04 /* Advertisement control reg */ -#define MII_LPA 0x05 /* Link partner ability reg */ -#define MII_EXPANSION 0x06 /* Expansion register */ -#define MII_DCOUNTER 0x12 /* Disconnect counter */ -#define MII_FCSCOUNTER 0x13 /* False carrier counter */ -#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ -#define MII_RERRCOUNTER 0x15 /* Receive error counter */ -#define MII_SREVISION 0x16 /* Silicon revision */ -#define MII_RESV1 0x17 /* Reserved... */ -#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */ -#define MII_PHYADDR 0x19 /* PHY address */ -#define MII_RESV2 0x1a /* Reserved... */ -#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */ -#define MII_NCONFIG 0x1c /* Network interface config */ +#define MII_BMCR 0x00 /* Basic mode control register */ +#define MII_BMSR 0x01 /* Basic mode status register */ +#define MII_PHYSID1 0x02 /* PHYS ID 1 */ +#define MII_PHYSID2 0x03 /* PHYS ID 2 */ +#define MII_ADVERTISE 0x04 /* Advertisement control reg */ +#define MII_LPA 0x05 /* Link partner ability reg */ +#define MII_EXPANSION 0x06 /* Expansion register */ +#define MII_CTRL1000 0x09 /* 1000BASE-T control */ +#define MII_STAT1000 0x0a /* 1000BASE-T status */ +#define MII_ESTATUS 0x0f /* Extended Status */ +#define MII_DCOUNTER 0x12 /* Disconnect counter */ +#define MII_FCSCOUNTER 0x13 /* False carrier counter */ +#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ +#define MII_RERRCOUNTER 0x15 /* Receive error counter */ +#define MII_SREVISION 0x16 /* Silicon revision */ +#define MII_RESV1 0x17 /* Reserved... */ +#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */ +#define MII_PHYADDR 0x19 /* PHY address */ +#define MII_RESV2 0x1a /* Reserved... */ +#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */ +#define MII_NCONFIG 0x1c /* Network interface config */ /* Basic mode control register. */ -#define BMCR_RESV 0x003f /* Unused... */ -#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */ -#define BMCR_CTST 0x0080 /* Collision test */ -#define BMCR_FULLDPLX 0x0100 /* Full duplex */ -#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ -#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */ -#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */ -#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ -#define BMCR_SPEED100 0x2000 /* Select 100Mbps */ -#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ -#define BMCR_RESET 0x8000 /* Reset the DP83840 */ +#define BMCR_RESV 0x003f /* Unused... */ +#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */ +#define BMCR_CTST 0x0080 /* Collision test */ +#define BMCR_FULLDPLX 0x0100 /* Full duplex */ +#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ +#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */ +#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */ +#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ +#define BMCR_SPEED100 0x2000 /* Select 100Mbps */ +#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ +#define BMCR_RESET 0x8000 /* Reset the DP83840 */ /* Basic mode status register. */ -#define BMSR_ERCAP 0x0001 /* Ext-reg capability */ -#define BMSR_JCD 0x0002 /* Jabber detected */ -#define BMSR_LSTATUS 0x0004 /* Link status */ -#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ -#define BMSR_RFAULT 0x0010 /* Remote fault detected */ -#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ -#define BMSR_RESV 0x07c0 /* Unused... */ -#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ -#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ -#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ -#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */ -#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */ +#define BMSR_ERCAP 0x0001 /* Ext-reg capability */ +#define BMSR_JCD 0x0002 /* Jabber detected */ +#define BMSR_LSTATUS 0x0004 /* Link status */ +#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ +#define BMSR_RFAULT 0x0010 /* Remote fault detected */ +#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ +#define BMSR_RESV 0x00c0 /* Unused... */ +#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ +#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */ +#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */ +#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ +#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ +#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ +#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */ +#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */ /* Advertisement control register. */ -#define ADVERTISE_SLCT 0x001f /* Selector bits */ -#define ADVERTISE_CSMA 0x0001 /* Only selector supported */ -#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */ -#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */ -#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */ -#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */ -#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */ -#define ADVERTISE_RESV 0x1c00 /* Unused... */ -#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */ -#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */ -#define ADVERTISE_NPAGE 0x8000 /* Next page bit */ +#define ADVERTISE_SLCT 0x001f /* Selector bits */ +#define ADVERTISE_CSMA 0x0001 /* Only selector supported */ +#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */ +#define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */ +#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */ +#define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */ +#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */ +#define ADVERTISE_1000XPAUSE 0x0080 /* Try for 1000BASE-X pause */ +#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */ +#define ADVERTISE_1000XPSE_ASYM 0x0100 /* Try for 1000BASE-X asym pause */ +#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */ +#define ADVERTISE_PAUSE_CAP 0x0400 /* Try for pause */ +#define ADVERTISE_PAUSE_ASYM 0x0800 /* Try for asymetric pause */ +#define ADVERTISE_RESV 0x1000 /* Unused... */ +#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */ +#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */ +#define ADVERTISE_NPAGE 0x8000 /* Next page bit */ #define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \ ADVERTISE_CSMA) #define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \ - ADVERTISE_100HALF | ADVERTISE_100FULL) + ADVERTISE_100HALF | ADVERTISE_100FULL) /* Link partner ability register. */ -#define LPA_SLCT 0x001f /* Same as advertise selector */ -#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */ -#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */ -#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */ -#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */ -#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */ -#define LPA_RESV 0x1c00 /* Unused... */ -#define LPA_RFAULT 0x2000 /* Link partner faulted */ -#define LPA_LPACK 0x4000 /* Link partner acked us */ -#define LPA_NPAGE 0x8000 /* Next page bit */ +#define LPA_SLCT 0x001f /* Same as advertise selector */ +#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */ +#define LPA_1000XFULL 0x0020 /* Can do 1000BASE-X full-duplex */ +#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */ +#define LPA_1000XHALF 0x0040 /* Can do 1000BASE-X half-duplex */ +#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */ +#define LPA_1000XPAUSE 0x0080 /* Can do 1000BASE-X pause */ +#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */ +#define LPA_1000XPAUSE_ASYM 0x0100 /* Can do 1000BASE-X pause asym*/ +#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */ +#define LPA_PAUSE_CAP 0x0400 /* Can pause */ +#define LPA_PAUSE_ASYM 0x0800 /* Can pause asymetrically */ +#define LPA_RESV 0x1000 /* Unused... */ +#define LPA_RFAULT 0x2000 /* Link partner faulted */ +#define LPA_LPACK 0x4000 /* Link partner acked us */ +#define LPA_NPAGE 0x8000 /* Next page bit */ #define LPA_DUPLEX (LPA_10FULL | LPA_100FULL) #define LPA_100 (LPA_100FULL | LPA_100HALF | LPA_100BASE4) /* Expansion register for auto-negotiation. */ -#define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */ -#define EXPANSION_LCWP 0x0002 /* Got new RX page code word */ -#define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */ -#define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */ -#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */ -#define EXPANSION_RESV 0xffe0 /* Unused... */ +#define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */ +#define EXPANSION_LCWP 0x0002 /* Got new RX page code word */ +#define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */ +#define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */ +#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */ +#define EXPANSION_RESV 0xffe0 /* Unused... */ + +#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */ +#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */ /* N-way test register. */ -#define NWAYTEST_RESV1 0x00ff /* Unused... */ -#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */ -#define NWAYTEST_RESV2 0xfe00 /* Unused... */ +#define NWAYTEST_RESV1 0x00ff /* Unused... */ +#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */ +#define NWAYTEST_RESV2 0xfe00 /* Unused... */ + +/* 1000BASE-T Control register */ +#define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */ +#define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */ +/* 1000BASE-T Status register */ +#define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */ +#define LPA_1000REMRXOK 0x1000 /* Link partner remote receiver status */ +#define LPA_1000FULL 0x0800 /* Link partner 1000BASE-T full duplex */ +#define LPA_1000HALF 0x0400 /* Link partner 1000BASE-T half duplex */ + +/* Flow control flags */ +#define FLOW_CTRL_TX 0x01 +#define FLOW_CTRL_RX 0x02 /** * mii_nway_result @@ -114,7 +148,7 @@ * * The one exception to IEEE 802.3u is that 100baseT4 is placed * between 100T-full and 100T-half. If your phy does not support - * 100T4 this is fine. If your phy places 100T4 elsewhere in the + * 100T4 this is fine. If your phy places 100T4 elsewhere in the * priority order, you will need to roll your own function. */ static inline unsigned int mii_nway_result (unsigned int negotiated) @@ -154,5 +188,4 @@ static inline unsigned int mii_duplex (unsigned int duplex_lock, return 0; } - #endif /* __LINUX_MII_H__ */ diff --git a/include/pci_ids.h b/include/pci_ids.h index dcc381d..cb8398d 100644 --- a/include/pci_ids.h +++ b/include/pci_ids.h @@ -882,6 +882,7 @@ #define PCI_DEVICE_ID_PLX_SPCOM200 0x1103 #define PCI_DEVICE_ID_PLX_DJINN_ITOO 0x1151 #define PCI_DEVICE_ID_PLX_R753 0x1152 +#define PCI_DEVICE_ID_PLX_9030 0x9030 #define PCI_DEVICE_ID_PLX_9050 0x9050 #define PCI_DEVICE_ID_PLX_9060 0x9060 #define PCI_DEVICE_ID_PLX_9060ES 0x906E diff --git a/include/post.h b/include/post.h index 957ce3b..519cef1 100644 --- a/include/post.h +++ b/include/post.h @@ -58,11 +58,13 @@ #elif defined (CONFIG_MPC85xx) #include <asm/immap_85xx.h> -#define _POST_WORD_ADDR (CONFIG_SYS_IMMR + offsetof(ccsr_pic_t, tfrr)) +#define _POST_WORD_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PIC_OFFSET + \ + offsetof(ccsr_pic_t, tfrr)) #elif defined (CONFIG_MPC86xx) #include <asm/immap_86xx.h> -#define _POST_WORD_ADDR (CONFIG_SYS_IMMR + offsetof(ccsr_pic_t, tfrr)) +#define _POST_WORD_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_PIC_OFFSET + \ + offsetof(ccsr_pic_t, tfrr)) #elif defined (CONFIG_4xx) #define _POST_WORD_ADDR \ |