diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/PMC440.h | 70 | ||||
| -rw-r--r-- | include/configs/canyonlands.h | 12 | ||||
| -rw-r--r-- | include/configs/fx12mm.h | 3 | ||||
| -rw-r--r-- | include/configs/ml507.h | 6 | ||||
| -rw-r--r-- | include/configs/xilinx-ppc.h | 136 | ||||
| -rw-r--r-- | include/configs/xilinx-ppc405.h | 91 | ||||
| -rw-r--r-- | include/configs/xilinx-ppc440.h | 88 |
7 files changed, 200 insertions, 206 deletions
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index 85342a6..7071ccb 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com. * Based on the sequoia configuration file. * @@ -46,6 +46,7 @@ #endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_F 1 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ #define CONFIG_BOARD_TYPES 1 /* support board types */ /*----------------------------------------------------------------------- @@ -79,6 +80,7 @@ #define CONFIG_SYS_USB_HOST 0xe0000400 #define CONFIG_SYS_FPGA_BASE0 0xef000000 /* 32 bit */ #define CONFIG_SYS_FPGA_BASE1 0xef100000 /* 16 bit */ +#define CONFIG_SYS_RESET_BASE 0xef200000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer @@ -139,7 +141,7 @@ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ #define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) @@ -217,13 +219,15 @@ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ #endif +#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ + /* 440EPx errata CHIP 11 */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_I2C_CMD_TREE 1 @@ -260,38 +264,50 @@ #define CONFIG_DTT_ADM1021 #define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } -#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \ + "\\\"painit\\\" to preboot command" #undef CONFIG_BOOTARGS /* Setup some board specific values for the default environment variables */ #define CONFIG_HOSTNAME pmc440 -#define CONFIG_SYS_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" -#define CONFIG_SYS_ROOTPATH "rootpath=/opt/eldk_410/ppc_4xx\0" +#define CONFIG_SYS_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" +#define CONFIG_SYS_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" #define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_SYS_BOOTFILE \ - CONFIG_SYS_ROOTPATH \ + CONFIG_SYS_BOOTFILE \ + CONFIG_SYS_ROOTPATH \ + "fdt_file=/tftpboot/pmc440/pmc440.dtb\0" \ "netdev=eth0\0" \ "ethrotate=no\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "kernel_addr=FC000000\0" \ - "ramdisk_addr=FC180000\0" \ + "addmisc=setenv bootargs ${bootargs} mem=${mem}\0" \ + "nandargs=setenv bootargs root=/dev/mtdblock6 rootfstype=jffs2 rw\0" \ + "nand_boot=run nandargs addip addtty addmisc;bootm ${kernel_addr}\0" \ + "nand_boot_fdt=run nandargs addip addtty addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm\0" \ + "net_nfs_fdt=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdt_file};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "kernel_addr=ffc00000\0" \ + "kernel_addr_r=200000\0" \ + "fpga_addr=fff00000\0" \ + "fdt_addr=fff80000\0" \ + "fdt_addr_r=800000\0" \ + "fpga=fpga loadb 0 ${fpga_addr}\0" \ "load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \ - "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 200000 FFFA0000 60000\0" \ + "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ + "cp.b 200000 fffa0000 60000\0" \ "" #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ @@ -366,14 +382,8 @@ CONFIG_SYS_POST_SPR) #define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -/* esd expects pram at end of physical memory. - * So no logbuffer at the moment. - */ -#if 0 #define CONFIG_LOGBUFFER -#endif -#define CONFIG_SYS_POST_CACHE_ADDR 0x10000000 /* free virtual address */ +#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ @@ -478,6 +488,10 @@ #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) #endif +/* Memory Bank 1 (RESET) initialization */ +#define CFG_EBC_PB1AP 0x7f817200 //0x03017200 +#define CFG_EBC_PB1CR (CFG_RESET_BASE | 0x1c000) + /* Memory Bank 4 (FPGA / 32Bit) initialization */ #define CONFIG_SYS_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */ #define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */ @@ -512,4 +526,6 @@ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_API 1 + #endif /* __CONFIG_H */ diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index ec08ba7..f8e8801 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -571,6 +571,16 @@ #define CONFIG_SYS_EBC_CFG 0xB8400000 /* EBC0_CFG */ /* + * Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO + * pin multiplexing correctly + */ +#if defined(CONFIG_ARCHES) +#define GPIO43_USE GPIO_SEL /* On Arches this pin is used as GPIO */ +#else +#define GPIO43_USE GPIO_ALT1 /* On Glacier this pin is used as ALT1 -> PerCS3 */ +#endif + +/* * PPC4xx GPIO Configuration */ #ifdef CONFIG_460EX @@ -698,7 +708,7 @@ {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \ {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \ {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO43_USE, GPIO_OUT_0},/* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \ {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \ {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \ diff --git a/include/configs/fx12mm.h b/include/configs/fx12mm.h index d45e7a0..8481c33 100644 --- a/include/configs/fx12mm.h +++ b/include/configs/fx12mm.h @@ -57,11 +57,8 @@ #define CONFIG_PREBOOT "echo U-Boot is up and runnining;" /*Flash*/ -#define CONFIG_SYS_FLASH_BASE XPAR_FLASH_2MX16_MEM0_BASEADDR #define CONFIG_SYS_FLASH_SIZE (4*1024*1024) #define CONFIG_SYS_MAX_FLASH_SECT 71 -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 #define MTDIDS_DEFAULT "nor0=fx12mm-flash" #define MTDPARTS_DEFAULT "mtdparts=fx12mm-flash:-(user)" diff --git a/include/configs/ml507.h b/include/configs/ml507.h index c637904..a7319e4 100644 --- a/include/configs/ml507.h +++ b/include/configs/ml507.h @@ -30,15 +30,15 @@ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SIZE 0x20000 #define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_OFFSET 0x340000 +#define CONFIG_ENV_OFFSET 0x340000 #define CONFIG_ENV_ADDR (XPAR_FLASH_MEM0_BASEADDR+CONFIG_ENV_OFFSET) /*Misc*/ -#define CONFIG_SYS_PROMPT "ml507:/# " /* Monitor Command Prompt */ +#define CONFIG_SYS_PROMPT "ml507:/# " /* Monitor Command Prompt */ #define CONFIG_PREBOOT "echo U-Boot is up and runnining;" /*Flash*/ -#define CONFIG_SYS_FLASH_SIZE (32*1024*1024) +#define CONFIG_SYS_FLASH_SIZE (32*1024*1024) #define CONFIG_SYS_MAX_FLASH_SECT 259 #define MTDIDS_DEFAULT "nor0=ml507-flash" #define MTDPARTS_DEFAULT "mtdparts=ml507-flash:-(user)" diff --git a/include/configs/xilinx-ppc.h b/include/configs/xilinx-ppc.h new file mode 100644 index 0000000..e7daa07 --- /dev/null +++ b/include/configs/xilinx-ppc.h @@ -0,0 +1,136 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * + * (C) Copyright 2008 + * Georg Schardt <schardt@team-ctech.de> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef __CONFIG_XLX_H +#define __CONFIG_XLX_H +/* +#define DEBUG +#define ET_DEBUG +*/ + +/*Mem Map*/ +#define CONFIG_SYS_SDRAM_BASE 0x0 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (192 * 1024) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) + +/*Cmd*/ +#include <config_cmd_default.h> +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_REGINFO +#undef CONFIG_CMD_JFFS2 +#undef CONFIG_JFFS2_CMDLINE +#undef CONFIG_CMD_SPI +#undef CONFIG_CMD_I2C +#undef CONFIG_CMD_DTT +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_PING +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_EEPROM +#undef CONFIG_CMD_IMLS + +/*Misc*/ +#define CONFIG_BOOTDELAY 5/* autoboot after 5 seconds */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 + /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_MEMTEST_START 0x00400000 + /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00C00000 + /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_LOAD_ADDR 0x00400000 + /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 + /* Extended board_into (bd_t) */ +#define CONFIG_SYS_HZ 1000 + /* decrementer freq: 1 ms ticks */ +#define CONFIG_CMDLINE_EDITING /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_LOOPW /* enable loopw command */ +#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE /* include version env variable */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ +#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + /* Initial Memory map for Linux */ + +/*Stack*/ +#define CONFIG_SYS_INIT_RAM_ADDR 0x800000/* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \ + - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +/*Speed*/ +#define CONFIG_SYS_CLK_FREQ XPAR_CORE_CLOCK_FREQ_HZ + +/*Flash*/ +#ifdef XPAR_FLASH_MEM0_BASEADDR +#define CONFIG_SYS_FLASH_BASE XPAR_FLASH_MEM0_BASEADDR +#define CONFIG_SYS_FLASH_CFI 1 +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_EMPTY_INFO 1 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_CMD_JFFS2 +#define CONFIG_JFFS2_CMDLINE +#else +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_NO_FLASH +#endif + +/* serial communication */ +#ifdef XPAR_UARTLITE_0_BASEADDR +#define CONFIG_XILINX_UARTLITE +#define CONFIG_SERIAL_BASE XPAR_UARTLITE_0_BASEADDR +#define CONFIG_BAUDRATE XPAR_UARTLITE_0_BAUDRATE +#define CONFIG_SYS_BAUDRATE_TABLE { CONFIG_BAUDRATE } +#else +#ifdef XPAR_UARTNS550_0_BASEADDR +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 4 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 XPAR_UARTNS550_0_BASEADDR +#define CONFIG_SYS_NS16550_CLK XPAR_UARTNS550_0_CLOCK_FREQ_HZ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 115200 } +#endif +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/xilinx-ppc405.h b/include/configs/xilinx-ppc405.h index 7458470..d335f1e 100644 --- a/include/configs/xilinx-ppc405.h +++ b/include/configs/xilinx-ppc405.h @@ -30,97 +30,10 @@ #define __CONFIG_H /* cpu parameter */ -#define CONFIG_4xx 1 #define CONFIG_405 1 +#define CONFIG_4xx 1 #define CONFIG_XILINX_405 1 -/* memory map */ -#define CONFIG_SYS_SDRAM_BASE 0x0 -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (192 * 1024) -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) - -/* u-boot commands configuration */ -#include <config_cmd_default.h> - -/*Misc*/ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* Extended board_into (bd_t) */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_CMDLINE_EDITING /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_LOOPW /* enable loopw command */ -#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE /* include version env variable */ -#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ -#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - /* Initial Memory map for Linux */ -#define CONFIG_SYS_CACHELINE_SIZE 32 -#define CONFIG_SYS_CACHELINE_SHIFT 2 - -/* stack */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_FLASH_CF 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_EMPTY_INFO 1 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_PROTECTION - -/* serial communication */ -#ifdef XPAR_UARTLITE_0_BASEADDR -#define CONFIG_XILINX_UARTLITE -#define CONFIG_SERIAL_BASE XPAR_UARTLITE_0_BASEADDR -#define CONFIG_BAUDRATE XPAR_UARTLITE_0_BAUDRATE -#define CONFIG_SYS_BAUDRATE_TABLE { CONFIG_BAUDRATE } -#else -#ifdef XPAR_UARTNS550_0_BASEADDR -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 4 -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550_COM1 XPAR_UARTNS550_0_BASEADDR -#define CONFIG_SYS_NS16550_CLK XPAR_UARTNS550_0_CLOCK_FREQ_HZ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 115200 } -#endif -#endif - -/* cmd config */ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_JFFS2 -#define CONFIG_JFFS2_CMDLINE -#undef CONFIG_CMD_SPI -#undef CONFIG_CMD_I2C -#undef CONFIG_CMD_DTT -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_PING -#undef CONFIG_CMD_DHCP -#undef CONFIG_CMD_EEPROM -#undef CONFIG_CMD_IMLS +#include <configs/xilinx-ppc.h> #endif diff --git a/include/configs/xilinx-ppc440.h b/include/configs/xilinx-ppc440.h index ac78420..6e938dc 100644 --- a/include/configs/xilinx-ppc440.h +++ b/include/configs/xilinx-ppc440.h @@ -17,90 +17,12 @@ #ifndef __CONFIG_GEN_H #define __CONFIG_GEN_H -/* -#define DEBUG -#define ET_DEBUG -*/ - /*CPU*/ -#define CONFIG_XILINX_440 1 -#define CONFIG_440 1 -#define CONFIG_4xx 1 - -/*Mem Map*/ -#define CONFIG_SYS_SDRAM_BASE 0x0 -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (192 * 1024) -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) -/*Uart*/ -#define CONFIG_XILINX_UARTLITE -#define CONFIG_BAUDRATE XPAR_UARTLITE_0_BAUDRATE -#define CONFIG_SYS_BAUDRATE_TABLE { XPAR_UARTLITE_0_BAUDRATE } -#define CONFIG_SERIAL_BASE XPAR_UARTLITE_0_BASEADDR - -/*Cmd*/ -#include <config_cmd_default.h> -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_JFFS2 -#define CONFIG_JFFS2_CMDLINE -#undef CONFIG_CMD_SPI -#undef CONFIG_CMD_I2C -#undef CONFIG_CMD_DTT -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_PING -#undef CONFIG_CMD_DHCP -#undef CONFIG_CMD_EEPROM -#undef CONFIG_CMD_IMLS - -/*Misc*/ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR 0x00400000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* Extended board_into (bd_t) */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_CMDLINE_EDITING /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_LOOPW /* enable loopw command */ -#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE /* include version env variable */ -#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ -#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */ - -/*Stack*/ -#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -/*Speed*/ -#define CONFIG_SYS_CLK_FREQ XPAR_CORE_CLOCK_FREQ_HZ +/*CPU*/ +#define CONFIG_4xx 1 +#define CONFIG_440 1 +#define CONFIG_XILINX_440 1 -/*Flash*/ -#define CONFIG_SYS_FLASH_BASE XPAR_FLASH_MEM0_BASEADDR -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_EMPTY_INFO 1 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_PROTECTION +#include <configs/xilinx-ppc.h> #endif /* __CONFIG_H */ |