diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/alpr.h | 101 |
1 files changed, 30 insertions, 71 deletions
diff --git a/include/configs/alpr.h b/include/configs/alpr.h index eeafcd6..c6731ba 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -31,8 +31,9 @@ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_BOARD_RESET 1 /* call board_reset() */ #undef CFG_DRAM_TEST /* Disable-takes long time! */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_SYS_CLK_FREQ 33333000 /* external freq to pll */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the @@ -81,44 +82,28 @@ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -#if 0 /* test-only */ -/*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. - * The DS1743 code assumes this condition (i.e. -- it assumes the base - * address for the RTC registers is: - * - * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE - * - *----------------------------------------------------------------------*/ -#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */ -#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ -#endif - -/*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ +#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ +#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ +#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ @@ -177,7 +162,7 @@ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ "flash_nfs=run nfsargs addip addtty;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ @@ -216,24 +201,10 @@ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_88E1111_CLK_DELAY 1 /* set CLK delay on ALPR */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ -#if 0 /* test-only */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ELF | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CFG_CMD_NET | \ - CFG_CMD_NFS | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SNTP ) -#else #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ CFG_CMD_ASKENV | \ CFG_CMD_DHCP | \ @@ -250,7 +221,6 @@ CFG_CMD_FPGA | \ CFG_CMD_NAND | \ CFG_CMD_REGINFO) -#endif /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -279,15 +249,12 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -321,7 +288,6 @@ ist das mit den multiple Device in PS Mode erklaert ...*/ - /* FPGA program pin configuration */ #define CFG_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ #define CFG_GPIO_DATA 19 /* FPGA data pin (cpu output) */ @@ -336,14 +302,12 @@ /* * NAND-FLASH stuff */ -#define CFG_MAX_NAND_DEVICE 2 -#define NAND_MAX_CHIPS 2 -#define CFG_NAND_BASE 0x50000000 /* NAND FLASH Base Address */ - -#if 0 -#define CONFIG_MTD_DEBUG -#define CONFIG_MTD_DEBUG_VERBOSE 4 -#endif +#define CFG_MAX_NAND_DEVICE 4 +#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE +#define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE + 0, CFG_NAND_BASE + 2, \ + CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 } +#define CFG_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup @@ -353,14 +317,9 @@ /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ #define CFG_EBC_PB0AP 0x92015480 #define CFG_EBC_PB0CR (CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ -/* Memory Bank 1 (NAND-FLASH) initialization */ -/*#define CFG_EBC_PB1AP 0x108f4380 */ /* TODO */ -/*#define CFG_EBC_PB1AP 0x7f854380 */ /* TODO */ -/*#define CFG_EBC_PB1AP 0x108553c0 */ -/*#define CFG_EBC_PB1AP 0x108053c0 */ -#define CFG_EBC_PB1AP 0x10810180 - -/*#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) *//* BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 1 (NAND-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */ #define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x1A000) /* BS=1MB,BU=R/W,BW=16bit */ /* |