diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/bamboo.h | 67 | ||||
| -rw-r--r-- | include/configs/katmai.h | 14 |
2 files changed, 20 insertions, 61 deletions
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index bcc736c..db58a9f 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2005-2006 + * (C) Copyright 2005-2007 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this @@ -43,7 +43,6 @@ * 2nd ethernet port you have to "undef" the following define. */ #define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */ -#define CFG_NAND_LEGACY /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the @@ -143,65 +142,13 @@ #endif /* CFG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- - * NAND-FLASH related + * NAND FLASH *----------------------------------------------------------------------*/ -#define NAND_CMD_REG (0x00) /* NandFlash Command Register */ -#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */ -#define NAND_DATA_REG (0x08) /* NandFlash Data Register */ -#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */ -#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */ -#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */ -#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */ -#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */ -#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */ -#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */ -#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */ -#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */ -#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */ -#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */ -#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */ -#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */ -#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */ -#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */ -#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */ - -/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */ -#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */ -#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */ -#define NAND0_CMD_READ2 0x50 -#define NAND0_CMD_READ_ID 0x90 -#define NAND0_CMD_READ_STATUS 0x70 -#define NAND0_CMD_RESET 0xFF -#define NAND0_CMD_PAGE_PROG 0x80 -#define NAND0_CMD_PAGE_PROG_TRUE 0x10 -#define NAND0_CMD_PAGE_PROG_DUMMY 0x11 -#define NAND0_CMD_BLOCK_ERASE 0x60 -#define NAND0_CMD_BLOCK_ERASE_END 0xD0 - -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0) -#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0) -#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0) -#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG)) -#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01)) - -/* not needed with 440EP NAND controller */ -#define NAND_CTL_CLRALE(nandptr) -#define NAND_CTL_SETALE(nandptr) -#define NAND_CTL_CLRCLE(nandptr) -#define NAND_CTL_SETCLE(nandptr) -#define NAND_DISABLE_CE(nand) -#define NAND_ENABLE_CE(nand) +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_CS 1 +#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ /*----------------------------------------------------------------------- * DDR SDRAM diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 7f55366..cc47a16 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -360,7 +360,19 @@ EBC_BXCR_BW_16BIT) /* Memory Bank 1 (Xilinx System ACE controller) initialization */ -#define CFG_EBC_PB1AP 0x7F8FFE80 +#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ + EBC_BXAP_TWT_ENCODE(4) | \ + EBC_BXAP_BCE_DISABLE | \ + EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | \ + EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | \ + EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | \ + EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_NONDELAYED | \ + EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED) #define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \ EBC_BXCR_BS_1MB | \ EBC_BXCR_BU_RW | \ |