diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/common.h | 4 | ||||
| -rw-r--r-- | include/commproc.h | 26 | ||||
| -rw-r--r-- | include/configs/lwmon.h | 587 | ||||
| -rw-r--r-- | include/pcmcia.h | 2 |
4 files changed, 0 insertions, 619 deletions
diff --git a/include/common.h b/include/common.h index 80c3486..29350e4 100644 --- a/include/common.h +++ b/include/common.h @@ -415,10 +415,6 @@ int eeprom_probe (unsigned dev_addr, unsigned offset); #endif int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); -#ifdef CONFIG_LWMON -extern uchar pic_read (uchar reg); -extern void pic_write (uchar reg, uchar val); -#endif /* * Set this up regardless of board diff --git a/include/commproc.h b/include/commproc.h index 8de0d15..509d6e4 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -543,32 +543,6 @@ typedef struct scc_enet { #endif /* CONFIG_IVMS8, CONFIG_IVML24 */ -/*** LWMON **********************************************************/ - -#if defined(CONFIG_LWMON) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003E00) -#endif /* CONFIG_LWMON */ - /*** KM8XX *********************************************************/ /* The KM8XX Service Module uses SCC3 for Ethernet */ diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h deleted file mode 100644 index f204587..0000000 --- a/include/configs/lwmon.h +++ /dev/null @@ -1,587 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* External logbuffer support */ -#define CONFIG_LOGBUFFER - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC823 1 /* This is a MPC823E CPU */ -#define CONFIG_LWMON 1 /* ...on a LWMON board */ - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -/* Default Ethernet MAC address */ -#define CONFIG_ETHADDR 00:11:B0:00:00:00 - -/* The default Ethernet MAC address can be overwritten just once */ -#ifdef CONFIG_ETHADDR -#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 -#endif - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f() */ -#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init() */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */ - -#define CONFIG_LCD 1 /* use LCD controller ... */ -#define CONFIG_MPC8XX_LCD -#define CONFIG_HLD1045 1 /* ... with a HLD1045 display */ - -#define CONFIG_LCD_LOGO 1 /* print our logo on the LCD */ -#define CONFIG_LCD_INFO 1 /* ... and some board info */ -#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ - -#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ -#define CONFIG_8xx_CONS_SCC2 1 /* Console is on SCC2 */ - -#define CONFIG_BAUDRATE 115200 /* with watchdog >= 38400 needed */ - -#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -/* pre-boot commands */ -#define CONFIG_PREBOOT "setenv bootdelay 15" - -#undef CONFIG_BOOTARGS - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_WATCHDOG | \ - CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_SPI | \ - CONFIG_SYS_POST_USB | \ - CONFIG_SYS_POST_SPR | \ - CONFIG_SYS_POST_SYSMON) - -/* - * Keyboard commands: - * # = 0x28 = ENTER : enable bootmessages on LCD - * 2 = 0x3A+0x3C = F1 + F3 : enable update mode - * 3 = 0x3C+0x3F = F3 + F6 : enable test mode - */ - -#define CONFIG_BOOTCOMMAND "source 40040000;saveenv" - -/* "gatewayip=10.8.211.250\0" \ */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40280000\0" \ - "netmask=255.255.192.0\0" \ - "serverip=10.8.2.101\0" \ - "ipaddr=10.8.57.0\0" \ - "magic_keys=#23\0" \ - "key_magic#=28\0" \ - "key_cmd#=setenv addfb setenv 'bootargs $bootargs console=tty0'\0" \ - "key_magic2=3A+3C\0" \ - "key_cmd2=echo *** Entering Update Mode ***;" \ - "if fatload ide 0:3 10000 update.scr;" \ - "then source 10000;" \ - "else echo *** UPDATE FAILED ***;" \ - "fi\0" \ - "key_magic3=3C+3F\0" \ - "key_cmd3=echo *** Entering Test Mode ***;" \ - "setenv add_misc 'setenv bootargs $bootargs testmode'\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addfb=setenv bootargs $bootargs console=ttyS1,$baudrate\0" \ - "addip=setenv bootargs $bootargs " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \ - "panic=1\0" \ - "add_wdt=setenv bootargs $bootargs $wdt_args\0" \ - "add_misc=setenv bootargs $bootargs runmode\0" \ - "flash_nfs=run nfsargs addip add_wdt addfb add_misc;" \ - "bootm $kernel_addr\0" \ - "flash_self=run ramargs addip add_wdt addfb add_misc;" \ - "bootm $kernel_addr $ramdisk_addr\0" \ - "net_nfs=tftp 100000 /tftpboot/uImage.lwmon;" \ - "run nfsargs addip add_wdt addfb;bootm\0" \ - "rootpath=/opt/eldk/ppc_8xx\0" \ - "load=tftp 100000 /tftpboot/u-boot.bin\0" \ - "update=protect off 1:0;era 1:0;cp.b 100000 40000000 $filesize\0" \ - "wdt_args=wdt_8xx=off\0" \ - "verify=no" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#define CONFIG_WATCHDOG 1 /* watchdog enabled */ -#define CONFIG_SYS_WATCHDOG_FREQ (CONFIG_SYS_HZ / 20) - -#undef CONFIG_STATUS_LED /* Status LED disabled */ - -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -/* - * Software (bit-bang) I2C driver configuration - */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ - - -#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BMP -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ - -/* - * When the watchdog is enabled, output must be fast enough in Linux. - */ -#ifdef CONFIG_WATCHDOG -#define CONFIG_SYS_BAUDRATE_TABLE { 38400, 57600, 115200 } -#endif - -/*----------------------------------------------------------------------*/ -#define CONFIG_MODEM_SUPPORT 1 /* enable modem initialization stuff */ -#undef CONFIG_MODEM_SUPPORT_DEBUG - -#define CONFIG_MODEM_KEY_MAGIC "3C+3D" /* press F3 + F4 keys to enable modem */ -#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ -#if 0 -#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ -#define CONFIG_AUTOBOOT_PROMPT \ - "\nEnter password - autoboot in %d sec...\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ -#endif -/*----------------------------------------------------------------------*/ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFFF00000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#if defined(DEBUG) || defined(CONFIG_CMD_IDE) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE -#define CONFIG_SYS_FLASH_BUFFER_WRITE_TOUT 2048 /* Timeout for Flash Buffer Write (in ms) */ -/* Buffer size. - We have two flash devices connected in parallel. - Each device incorporates a Write Buffer of 32 bytes. - */ -#define CONFIG_SYS_FLASH_BUFFER_SIZE (2*32) - -/* Put environment in flash which is much faster to boot than using the EEPROM */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x40040000 /* Address of Environment Sector */ -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment */ -#define CONFIG_ENV_SECT_SIZE 0x40000 /* we have BIG sectors only :-( */ - -/*----------------------------------------------------------------------- - * I2C/EEPROM Configuration - */ - -#define CONFIG_SYS_I2C_AUDIO_ADDR 0x28 /* Audio volume control */ -#define CONFIG_SYS_I2C_SYSMON_ADDR 0x2E /* LM87 System Monitor */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */ -#define CONFIG_SYS_I2C_POWER_A_ADDR 0x52 /* PCMCIA/USB power switch, channel A */ -#define CONFIG_SYS_I2C_POWER_B_ADDR 0x53 /* PCMCIA/USB power switch, channel B */ -#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ -#define CONFIG_SYS_I2C_PICIO_ADDR 0x57 /* PIC IO Expander */ - -#undef CONFIG_USE_FRAM /* Use FRAM instead of EEPROM */ - -#ifdef CONFIG_USE_FRAM /* use FRAM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x55 /* FRAM FM24CL64 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#else /* use EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ -#endif /* CONFIG_USE_FRAM */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 - -/* List of I2C addresses to be verified by POST */ -#ifdef CONFIG_USE_FRAM -#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \ - CONFIG_SYS_I2C_SYSMON_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_POWER_A_ADDR, \ - CONFIG_SYS_I2C_POWER_B_ADDR, \ - CONFIG_SYS_I2C_KEYBD_ADDR, \ - CONFIG_SYS_I2C_PICIO_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - } -#else /* Use EEPROM - which show up on 8 consequtive addresses */ -#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \ - CONFIG_SYS_I2C_SYSMON_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_POWER_A_ADDR, \ - CONFIG_SYS_I2C_POWER_B_ADDR, \ - CONFIG_SYS_I2C_KEYBD_ADDR, \ - CONFIG_SYS_I2C_PICIO_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR+0, \ - CONFIG_SYS_I2C_EEPROM_ADDR+1, \ - CONFIG_SYS_I2C_EEPROM_ADDR+2, \ - CONFIG_SYS_I2C_EEPROM_ADDR+3, \ - CONFIG_SYS_I2C_EEPROM_ADDR+4, \ - CONFIG_SYS_I2C_EEPROM_ADDR+5, \ - CONFIG_SYS_I2C_EEPROM_ADDR+6, \ - CONFIG_SYS_I2C_EEPROM_ADDR+7, \ - } -#endif /* CONFIG_USE_FRAM */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if 0 && defined(CONFIG_WATCHDOG) /* LWMON uses external MAX706TESA WD */ -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -/* EARB, DBGC and DBPC are initialised by the HCW */ -/* => 0x000000C0 */ -#define CONFIG_SYS_SIUMCR (SIUMCR_GB5E) -/*#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit, set PLL multiplication factor ! - */ -/* 0x00405000 */ -#define CONFIG_SYS_PLPRCR_MF 4 /* (4+1) * 13.2 = 66 MHz Clock */ -#define CONFIG_SYS_PLPRCR \ - ( (CONFIG_SYS_PLPRCR_MF << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ - /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ - PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \ - ) - -#define CONFIG_8xx_GCLK_FREQ ((CONFIG_SYS_PLPRCR_MF+1)*13200000) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -/* 0x01800000 */ -#define CONFIG_SYS_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \ - SCCR_RTDIV | SCCR_RTSEL | \ - /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ - SCCR_EBDF00 | SCCR_DFSYNC00 | \ - SCCR_DFBRG00 | SCCR_DFNL000 | \ - SCCR_DFNH000 | SCCR_DFLCD100 | \ - SCCR_DFALCD01) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -/* 0x00C3 => 0x0003 */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration Register 19-4 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0x0000 - -/*----------------------------------------------------------------------- - * RMDS - RISC Microcode Development Support Control Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMDS 0 - -/*----------------------------------------------------------------------- - * - * Interrupt Levels - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0x50000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0x54000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0x58000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0x5C000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ - -#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -#define CONFIG_SUPPORT_VFAT /* enable VFAT support */ - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - second Flash bank optional - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x41000000 /* FLASH bank #1 */ - -/* used to re-map FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0xFF000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* OR addr mask */ - -/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 8, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK) - -#define CONFIG_SYS_OR0_REMAP ( CONFIG_SYS_REMAP_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ - CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \ - CONFIG_SYS_OR_TIMING_FLASH) -/* 16 bit, bank valid */ -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V ) - -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM -#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V ) - -/* - * BR3/OR3: SDRAM - * - * Multiplexed addresses, GPL5 output to GPL5_A (don't care) - */ -#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ -#define SDRAM_PRELIM_OR_AM 0xF0000000 /* map 256 MB (>SDRAM_MAX_SIZE!) */ -#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */ - -#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB SDRAM */ - -#define CONFIG_SYS_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING ) -#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -/* - * BR5/OR5: Touch Panel - * - * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0 - */ -#define TOUCHPNL_BASE 0x20000000 -#define TOUCHPNL_OR_AM 0xFFFF8000 -#define TOUCHPNL_TIMING OR_SCY_0_CLK - -#define CONFIG_SYS_OR5_PRELIM (TOUCHPNL_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ - TOUCHPNL_TIMING ) -#define CONFIG_SYS_BR5_PRELIM ((TOUCHPNL_BASE & BR_BA_MSK) | BR_PS_32 | BR_V ) - -#define CONFIG_SYS_MEMORY_75 -#undef CONFIG_SYS_MEMORY_7E -#undef CONFIG_SYS_MEMORY_8E - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MPTPR 0x200 - -/* - * MAMR settings for SDRAM - */ - -#define CONFIG_SYS_MAMR_8COL 0x80802114 -#define CONFIG_SYS_MAMR_9COL 0x80904114 - -/* - * MAR setting for SDRAM - */ -#define CONFIG_SYS_MAR 0x00000088 - -#endif /* __CONFIG_H */ diff --git a/include/pcmcia.h b/include/pcmcia.h index 7e495bc..54ab2ac 100644 --- a/include/pcmcia.h +++ b/include/pcmcia.h @@ -25,8 +25,6 @@ # define CONFIG_PCMCIA_SLOT_B /* The TQM8xxL use SLOT_B */ #elif defined(CONFIG_IVMS8) || defined(CONFIG_IVML24) /* The IVM* use SLOT_A */ # define CONFIG_PCMCIA_SLOT_A -#elif defined(CONFIG_LWMON) /* The LWMON use SLOT_B */ -# define CONFIG_PCMCIA_SLOT_B #elif defined(CONFIG_ATC) /* The ATC use SLOT_A */ # define CONFIG_PCMCIA_SLOT_A #else |