diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/yucca.h | 62 |
1 files changed, 33 insertions, 29 deletions
diff --git a/include/configs/yucca.h b/include/configs/yucca.h index e6d9843..ee5a448 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -152,29 +152,13 @@ #undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ #define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_BOOTARGS "console=ttyS0,115200n8 root=/dev/nfs rw" -#define CONFIG_BOOTCOMMAND "bootm E7C00000" /* autoboot command */ -#define CONFIG_BOOTDELAY -1 /* -1 to disable autoboot */ +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#undef CONFIG_NET_MULTI -#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ -#define CONFIG_HAS_ETH0 -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_PHY_RESET_DELAY 1000 -#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CONFIG_NETMASK 255.255.0.0 -#define CONFIG_IPADDR 192.168.80.10 -#define CONFIG_ETHADDR 00:04:AC:01:CA:FE -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SERVERIP 192.168.1.1 +#undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ - "loads_echo=1\0" \ "netdev=eth0\0" \ "hostname=yucca\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ @@ -190,7 +174,7 @@ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ - "rootpath=/opt/eldk-4.0/ppc_4xx\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ "bootfile=yucca/uImage\0" \ "kernel_addr=E7F10000\0" \ "ramdisk_addr=E7F20000\0" \ @@ -200,22 +184,42 @@ "setenv filesize;saveenv\0" \ "upd=run load;run update\0" \ "" +#define CONFIG_BOOTCOMMAND "run flash_self" -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_PCI | \ - CFG_CMD_IRQ | \ - CFG_CMD_I2C | \ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_EEPROM | \ CFG_CMD_DHCP | \ - CFG_CMD_PING | \ CFG_CMD_DIAG | \ - CFG_CMD_NET | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ CFG_CMD_MII | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF ) + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> +#define CONFIG_MII 1 /* MII PHY management */ +#undef CONFIG_NET_MULTI +#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ +#define CONFIG_HAS_ETH0 +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 1000 +#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + #undef CONFIG_WATCHDOG /* watchdog disabled */ /* |