diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/asm-arm/arch-pxa/pxa-regs.h | 121 | ||||
| -rw-r--r-- | include/configs/delta.h | 141 | ||||
| -rw-r--r-- | include/crc.h | 101 | ||||
| -rw-r--r-- | include/da9030.h | 106 | ||||
| -rw-r--r-- | include/environment.h | 12 | ||||
| -rw-r--r-- | include/xyzModem.h | 112 |
6 files changed, 434 insertions, 159 deletions
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h index 83ae5e3..ebda719 100644 --- a/include/asm-arm/arch-pxa/pxa-regs.h +++ b/include/asm-arm/arch-pxa/pxa-regs.h @@ -475,11 +475,11 @@ typedef void (*ExcpHndlr) (void) ; #define ICR_ACKNAK 0x4 /* send ACK(0) or NAK(1) */ #define ICR_TB 0x8 /* transfer byte bit */ #define ICR_MA 0x10 /* master abort */ -#define ICR_SCLE 0x20 /* master clock enable */ +#define ICR_SCLE 0x20 /* master clock enable, mona SCLEA */ #define ICR_IUE 0x40 /* unit enable */ #define ICR_GCD 0x80 /* general call disable */ #define ICR_ITEIE 0x100 /* enable tx interrupts */ -#define ICR_IRFIE 0x200 /* enable rx interrupts */ +#define ICR_IRFIE 0x200 /* enable rx interrupts, mona: DRFIE */ #define ICR_BEIE 0x400 /* enable bus error ints */ #define ICR_SSDIE 0x800 /* slave STOP detected int enable */ #define ICR_ALDIE 0x1000 /* enable arbitration interrupt */ @@ -821,21 +821,21 @@ typedef void (*ExcpHndlr) (void) ; #define RTAR __REG(0x40900004) /* RTC Alarm Register */ #define RTSR __REG(0x40900008) /* RTC Status Register */ #define RTTR __REG(0x4090000C) /* RTC Timer Trim Register */ -#define RDAR1 __REG(0x40900018) /* Wristwatch Day Alarm Reg 1 */ -#define RDAR2 __REG(0x40900020) /* Wristwatch Day Alarm Reg 2 */ -#define RYAR1 __REG(0x4090001C) /* Wristwatch Year Alarm Reg 1 */ -#define RYAR2 __REG(0x40900024) /* Wristwatch Year Alarm Reg 2 */ -#define SWAR1 __REG(0x4090002C) /* Stopwatch Alarm Register 1 */ -#define SWAR2 __REG(0x40900030) /* Stopwatch Alarm Register 2 */ -#define PIAR __REG(0x40900038) /* Periodic Interrupt Alarm Register */ -#define RDCR __REG(0x40900010) /* RTC Day Count Register. */ -#define RYCR __REG(0x40900014) /* RTC Year Count Register. */ -#define SWCR __REG(0x40900028) /* Stopwatch Count Register */ -#define RTCPICR __REG(0x40900034) /* Periodic Interrupt Counter Register */ - -#define RTSR_PICE (1 << 15) /* Peridoc interrupt count enable */ -#define RTSR_PIALE (1 << 14) /* Peridoc interrupt Alarm enable */ -#define RTSR_PIAL (1 << 13) /* Peridoc interrupt Alarm status */ +#define RDAR1 __REG(0x40900018) /* Wristwatch Day Alarm Reg 1 */ +#define RDAR2 __REG(0x40900020) /* Wristwatch Day Alarm Reg 2 */ +#define RYAR1 __REG(0x4090001C) /* Wristwatch Year Alarm Reg 1 */ +#define RYAR2 __REG(0x40900024) /* Wristwatch Year Alarm Reg 2 */ +#define SWAR1 __REG(0x4090002C) /* Stopwatch Alarm Register 1 */ +#define SWAR2 __REG(0x40900030) /* Stopwatch Alarm Register 2 */ +#define PIAR __REG(0x40900038) /* Periodic Interrupt Alarm Register */ +#define RDCR __REG(0x40900010) /* RTC Day Count Register. */ +#define RYCR __REG(0x40900014) /* RTC Year Count Register. */ +#define SWCR __REG(0x40900028) /* Stopwatch Count Register */ +#define RTCPICR __REG(0x40900034) /* Periodic Interrupt Counter Register */ + +#define RTSR_PICE (1 << 15) /* Peridoc interrupt count enable */ +#define RTSR_PIALE (1 << 14) /* Peridoc interrupt Alarm enable */ +#define RTSR_PIAL (1 << 13) /* Peridoc interrupt Alarm status */ #define RTSR_HZE (1 << 3) /* HZ interrupt enable */ #define RTSR_ALE (1 << 2) /* RTC alarm interrupt enable */ #define RTSR_HZ (1 << 1) /* HZ rising-edge detected */ @@ -921,9 +921,10 @@ typedef void (*ExcpHndlr) (void) ; #ifdef CONFIG_CPU_MONAHANS #define ICHP __REG(0x40D00018) /* Interrupt Controller Highest Priority Register */ -/* Missing: 32 Interrupt priority registers */ -/* mk@tbd: These are the same as beneath for PXA27x: maybe can be - * merged if GPIO Stuff is same too. */ +/* Missing: 32 Interrupt priority registers + * These are the same as beneath for PXA27x: maybe can be merged if + * GPIO Stuff is same too. + */ #define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */ #define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */ #define ICLR2 __REG(0x40D000A4) /* Interrupt Controller Level Register 2 */ @@ -983,24 +984,24 @@ typedef void (*ExcpHndlr) (void) ; #define GCDR3 __REG(0x40E0042C) /* Bit-wise Clear of GPDR[127:96] */ #define GSRER0 __REG(0x40E00440) /* Set Rising Edge Det. Enable [31:0] */ -#define GSRER1 __REG(0x40E00444) /* Set Rising Edge Det. Enable [63:32] */ +#define GSRER1 __REG(0x40E00444) /* Set Rising Edge Det. Enable [63:32] */ #define GSRER2 __REG(0x40E00448) /* Set Rising Edge Det. Enable [95:64] */ -#define GSRER3 __REG(0x40E0044C) /* Set Rising Edge Det. Enable [127:96] */ +#define GSRER3 __REG(0x40E0044C) /* Set Rising Edge Det. Enable [127:96] */ #define GCRER0 __REG(0x40E00460) /* Clear Rising Edge Det. Enable [31:0] */ -#define GCRER1 __REG(0x40E00464) /* Clear Rising Edge Det. Enable [63:32] */ +#define GCRER1 __REG(0x40E00464) /* Clear Rising Edge Det. Enable [63:32] */ #define GCRER2 __REG(0x40E00468) /* Clear Rising Edge Det. Enable [95:64] */ -#define GCRER3 __REG(0x40E0046C) /* Clear Rising Edge Det. Enable[127:96] */ +#define GCRER3 __REG(0x40E0046C) /* Clear Rising Edge Det. Enable[127:96] */ #define GSFER0 __REG(0x40E00480) /* Set Falling Edge Det. Enable [31:0] */ -#define GSFER1 __REG(0x40E00484) /* Set Falling Edge Det. Enable [63:32] */ +#define GSFER1 __REG(0x40E00484) /* Set Falling Edge Det. Enable [63:32] */ #define GSFER2 __REG(0x40E00488) /* Set Falling Edge Det. Enable [95:64] */ -#define GSFER3 __REG(0x40E0048C) /* Set Falling Edge Det. Enable[127:96] */ +#define GSFER3 __REG(0x40E0048C) /* Set Falling Edge Det. Enable[127:96] */ #define GCFER0 __REG(0x40E004A0) /* Clr Falling Edge Det. Enable [31:0] */ -#define GCFER1 __REG(0x40E004A4) /* Clr Falling Edge Det. Enable [63:32] */ +#define GCFER1 __REG(0x40E004A4) /* Clr Falling Edge Det. Enable [63:32] */ #define GCFER2 __REG(0x40E004A8) /* Clr Falling Edge Det. Enable [95:64] */ -#define GCFER3 __REG(0x40E004AC) /* Clr Falling Edge Det. Enable[127:96] */ +#define GCFER3 __REG(0x40E004AC) /* Clr Falling Edge Det. Enable[127:96] */ #define GSDR(x) __REG2(0x40E00400, ((x) & 0x60) >> 3) #define GCDR(x) __REG2(0x40300420, ((x) & 0x60) >> 3) @@ -1488,8 +1489,8 @@ typedef void (*ExcpHndlr) (void) ; #define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT) #define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT) -#define GPIO117_SCL (117 | GPIO_ALT_FN_1_OUT) -#define GPIO118_SDA (118 | GPIO_ALT_FN_1_OUT) +#define GPIO117_SCL (117 | GPIO_ALT_FN_1_OUT) +#define GPIO118_SDA (118 | GPIO_ALT_FN_1_OUT) /* * Power Manager @@ -1709,10 +1710,10 @@ typedef void (*ExcpHndlr) (void) ; #define ACCR_13MEND2 (1 << 21) #define ACCR_PCCE (1 << 11) -#define CKENA_30_MSL0 (1 << 30) /* MSL0 Interface Unit Clock Enable */ -#define CKENA_29_SSP4 (1 << 29) /* SSP3 Unit Clock Enable */ -#define CKENA_28_SSP3 (1 << 28) /* SSP2 Unit Clock Enable */ -#define CKENA_27_SSP2 (1 << 27) /* SSP1 Unit Clock Enable */ +#define CKENA_30_MSL0 (1 << 30) /* MSL0 Interface Unit Clock Enable */ +#define CKENA_29_SSP4 (1 << 29) /* SSP3 Unit Clock Enable */ +#define CKENA_28_SSP3 (1 << 28) /* SSP2 Unit Clock Enable */ +#define CKENA_27_SSP2 (1 << 27) /* SSP1 Unit Clock Enable */ #define CKENA_26_SSP1 (1 << 26) /* SSP0 Unit Clock Enable */ #define CKENA_25_TSI (1 << 25) /* TSI Clock Enable */ #define CKENA_24_AC97 (1 << 24) /* AC97 Unit Clock Enable */ @@ -1720,27 +1721,27 @@ typedef void (*ExcpHndlr) (void) ; #define CKENA_22_FFUART (1 << 22) /* FFUART Unit Clock Enable */ #define CKENA_21_BTUART (1 << 21) /* BTUART Unit Clock Enable */ #define CKENA_20_UDC (1 << 20) /* UDC Clock Enable */ -#define CKENA_19_TPM (1 << 19) /* TPM Unit Clock Enable */ -#define CKENA_18_USIM1 (1 << 18) /* USIM1 Unit Clock Enable */ -#define CKENA_17_USIM0 (1 << 17) /* USIM0 Unit Clock Enable */ -#define CKENA_15_CIR (1 << 15) /* Consumer IR Clock Enable */ -#define CKENA_14_KEY (1 << 14) /* Keypad Controller Clock Enable */ -#define CKENA_13_MMC1 (1 << 13) /* MMC1 Clock Enable */ -#define CKENA_12_MMC0 (1 << 12) /* MMC0 Clock Enable */ -#define CKENA_11_FLASH (1 << 11) /* Boot ROM Clock Enable */ -#define CKENA_10_SRAM (1 << 10) /* SRAM Controller Clock Enable */ -#define CKENA_9_SMC (1 << 9) /* Static Memory Controller */ -#define CKENA_8_DMC (1 << 8) /* Dynamic Memory Controller */ -#define CKENA_7_GRAPHICS (1 << 7) /* 2D Graphics Clock Enable */ +#define CKENA_19_TPM (1 << 19) /* TPM Unit Clock Enable */ +#define CKENA_18_USIM1 (1 << 18) /* USIM1 Unit Clock Enable */ +#define CKENA_17_USIM0 (1 << 17) /* USIM0 Unit Clock Enable */ +#define CKENA_15_CIR (1 << 15) /* Consumer IR Clock Enable */ +#define CKENA_14_KEY (1 << 14) /* Keypad Controller Clock Enable */ +#define CKENA_13_MMC1 (1 << 13) /* MMC1 Clock Enable */ +#define CKENA_12_MMC0 (1 << 12) /* MMC0 Clock Enable */ +#define CKENA_11_FLASH (1 << 11) /* Boot ROM Clock Enable */ +#define CKENA_10_SRAM (1 << 10) /* SRAM Controller Clock Enable */ +#define CKENA_9_SMC (1 << 9) /* Static Memory Controller */ +#define CKENA_8_DMC (1 << 8) /* Dynamic Memory Controller */ +#define CKENA_7_GRAPHICS (1 << 7) /* 2D Graphics Clock Enable */ #define CKENA_6_USBCLI (1 << 6) /* USB Client Unit Clock Enable */ -#define CKENA_4_NAND (1 << 4) /* NAND Flash Controller Clock Enable */ -#define CKENA_3_CAMERA (1 << 3) /* Camera Interface Clock Enable */ +#define CKENA_4_NAND (1 << 4) /* NAND Flash Controller Clock Enable */ +#define CKENA_3_CAMERA (1 << 3) /* Camera Interface Clock Enable */ #define CKENA_2_USBHOST (1 << 2) /* USB Host Unit Clock Enable */ #define CKENA_1_LCD (1 << 1) /* LCD Unit Clock Enable */ #define CKENB_8_1WIRE ((1 << 8) + 32) /* One Wire Interface Unit Clock Enable */ -#define CKENB_7_GPIO ((1 << 7) + 32) /* GPIO Clock Enable */ -#define CKENB_6_IRQ ((1 << 6) + 32) /* Interrupt Controller Clock Enable */ +#define CKENB_7_GPIO ((1 << 7) + 32) /* GPIO Clock Enable */ +#define CKENB_6_IRQ ((1 << 6) + 32) /* Interrupt Controller Clock Enable */ #define CKENB_4_I2C ((1 << 4) + 32) /* I2C Unit Clock Enable */ #define CKENB_1_PWM1 ((1 << 1) + 32) /* PWM2 & PWM3 Clock Enable */ #define CKENB_0_PWM0 ((1 << 0) + 32) /* PWM0 & PWM1 Clock Enable */ @@ -2382,16 +2383,16 @@ typedef void (*ExcpHndlr) (void) ; #define KPAS_SO (0x1 << 31) #define KPASMKPx_SO (0x1 << 31) -#define GPIO113_BIT (1 << 17)/* GPIO113 in GPSR, GPCR, bit 17 */ -#define PSLR __REG(0x40F00034) -#define PSTR __REG(0x40F00038) /* Power Manager Standby Configuration Reg */ -#define PSNR __REG(0x40F0003C) /* Power Manager Sense Configuration Reg */ -#define PVCR __REG(0x40F00040) /* Power Manager Voltage Change Control Reg */ -#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-Up Enable Reg */ -#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Status Reg */ -#define OSMR4 __REG(0x40A00080) /* */ -#define OSCR4 __REG(0x40A00040) /* OS Timer Counter Register */ -#define OMCR4 __REG(0x40A000C0) /* */ +#define GPIO113_BIT (1 << 17)/* GPIO113 in GPSR, GPCR, bit 17 */ +#define PSLR __REG(0x40F00034) +#define PSTR __REG(0x40F00038) /* Power Manager Standby Configuration Reg */ +#define PSNR __REG(0x40F0003C) /* Power Manager Sense Configuration Reg */ +#define PVCR __REG(0x40F00040) /* Power Manager Voltage Change Control Reg */ +#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-Up Enable Reg */ +#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Status Reg */ +#define OSMR4 __REG(0x40A00080) /* */ +#define OSCR4 __REG(0x40A00040) /* OS Timer Counter Register */ +#define OMCR4 __REG(0x40A000C0) /* */ #endif /* CONFIG_PXA27X */ diff --git a/include/configs/delta.h b/include/configs/delta.h index b42a7e2..5edea95 100644 --- a/include/configs/delta.h +++ b/include/configs/delta.h @@ -49,7 +49,6 @@ /* * Hardware drivers */ - #undef TURN_ON_ETHERNET #ifdef TURN_ON_ETHERNET # define CONFIG_DRIVER_SMC91111 1 @@ -59,10 +58,18 @@ # undef CONFIG_SMC_USE_IOFUNCS /* just for use with the kernel */ #endif +#define CONFIG_HARD_I2C 1 /* required for DA9030 access */ +#define CFG_I2C_SPEED 400000 /* I2C speed */ +#define CFG_I2C_SLAVE 1 /* I2C controllers address */ +#define DA9030_I2C_ADDR 0x49 /* I2C address of DA9030 */ +#define CFG_DA9030_EXTON_DELAY 100000 /* wait x us after DA9030 reset via EXTON */ +#define CFG_I2C_INIT_BOARD 1 +/* #define CONFIG_HW_WATCHDOG 1 /\* Required for hitting the DA9030 WD *\/ */ + /* * select serial console configuration */ -#define CONFIG_FFUART 1 +#define CONFIG_FFUART 1 /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE @@ -73,8 +80,13 @@ #ifdef TURN_ON_ETHERNET # define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING) #else -# define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_ENV | CFG_CMD_NAND) \ - & ~(CFG_CMD_NET | CFG_CMD_FLASH | CFG_CMD_IMLS)) +# define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_ENV \ + | CFG_CMD_NAND \ + | CFG_CMD_I2C) \ + & ~(CFG_CMD_NET \ + | CFG_CMD_FLASH \ + | CFG_CMD_IMLS)) #endif @@ -114,15 +126,19 @@ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_DEVICE_NULLDEV 1 -#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ +#define CFG_MEMTEST_START 0x80400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x80800000 /* 4 ... 8 MB in DRAM */ #undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ #define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */ -#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ -#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */ +#define CFG_HZ 3250000 /* incrementer freq: 3.25 MHz */ + +/* Monahans Core Frequency */ +#define CFG_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */ +#define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */ + /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } @@ -144,16 +160,16 @@ * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */ -#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1 0x80000000 /* SDRAM Bank #1 */ #define PHYS_SDRAM_1_SIZE 0x1000000 /* 64 MB */ -#define PHYS_SDRAM_2 0xa1000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2 0x81000000 /* SDRAM Bank #2 */ #define PHYS_SDRAM_2_SIZE 0x1000000 /* 64 MB */ -#define PHYS_SDRAM_3 0xa2000000 /* SDRAM Bank #3 */ +#define PHYS_SDRAM_3 0x82000000 /* SDRAM Bank #3 */ #define PHYS_SDRAM_3_SIZE 0x1000000 /* 64 MB */ -#define PHYS_SDRAM_4 0xa3000000 /* SDRAM Bank #4 */ +#define PHYS_SDRAM_4 0x83000000 /* SDRAM Bank #4 */ #define PHYS_SDRAM_4_SIZE 0x1000000 /* 64 MB */ -#define CFG_DRAM_BASE 0xa0000000 /* at CS0 */ +#define CFG_DRAM_BASE 0x80000000 /* at CS0 */ #define CFG_DRAM_SIZE 0x04000000 /* 64 MB Ram */ #undef CFG_SKIP_DRAM_SCRUB @@ -168,8 +184,6 @@ #define CFG_NAND_BASE_LIST { CFG_NAND0_BASE } #define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 -#define NAND_DELAY_US 25 /* mk@tbd: could be 0, I guess */ /* nand timeout values */ #define CFG_NAND_PROG_ERASE_TO 3000 @@ -178,16 +192,15 @@ #undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */ /* NAND Timing Parameters (in ns) */ -#define NAND_TIMING_tCH 10 -#define NAND_TIMING_tCS 0 +#define NAND_TIMING_tCH 10 +#define NAND_TIMING_tCS 0 #define NAND_TIMING_tWH 20 -#define NAND_TIMING_tWP 40 +#define NAND_TIMING_tWP 40 -#define NAND_TIMING_tRH 20 -#define NAND_TIMING_tRP 40 +#define NAND_TIMING_tRH 20 +#define NAND_TIMING_tRP 40 -#define NAND_TIMING_tR 11123 -/* #define NAND_TIMING_tWHR 110 */ +#define NAND_TIMING_tR 11123 #define NAND_TIMING_tWHR 100 #define NAND_TIMING_tAR 10 @@ -199,89 +212,19 @@ #define CONFIG_MTD_DEBUG #define CONFIG_MTD_DEBUG_VERBOSE 1 -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 #define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NO_FLASH 1 -#ifndef CGF_NO_FLASH -/* these are required by the environment code */ -#define PHYS_FLASH_1 CFG_NAND0_BASE /* Flash Bank #1 */ -#define PHYS_FLASH_SIZE 0x04000000 /* 64 MB */ -#define PHYS_FLASH_BANK_SIZE 0x04000000 /* 64 MB Banks */ -#define PHYS_FLASH_SECT_SIZE (SECTORSIZE*1024) /* KB sectors (x2) */ -#endif - -/* - * GPIO settings - */ -#define CFG_GPSR0_VAL 0x00008000 -#define CFG_GPSR1_VAL 0x00FC0382 -#define CFG_GPSR2_VAL 0x0001FFFF -#define CFG_GPCR0_VAL 0x00000000 -#define CFG_GPCR1_VAL 0x00000000 -#define CFG_GPCR2_VAL 0x00000000 -#define CFG_GPDR0_VAL 0x0060A800 -#define CFG_GPDR1_VAL 0x00FF0382 -#define CFG_GPDR2_VAL 0x0001C000 -#define CFG_GAFR0_L_VAL 0x98400000 -#define CFG_GAFR0_U_VAL 0x00002950 -#define CFG_GAFR1_L_VAL 0x000A9558 -#define CFG_GAFR1_U_VAL 0x0005AAAA -#define CFG_GAFR2_L_VAL 0xA0000000 -#define CFG_GAFR2_U_VAL 0x00000002 - -#define CFG_PSSR_VAL 0x20 - -/* - * Memory settings - */ -#define CFG_MSC0_VAL 0x23F223F2 -#define CFG_MSC1_VAL 0x3FF1A441 -#define CFG_MSC2_VAL 0x7FF97FF1 -#define CFG_MDCNFG_VAL 0x00001AC9 -#define CFG_MDREFR_VAL 0x00018018 -#define CFG_MDMRS_VAL 0x00000000 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 -/* - * PCMCIA and CF Interfaces - */ -#define CFG_MECR_VAL 0x00000000 -#define CFG_MCMEM0_VAL 0x00010504 -#define CFG_MCMEM1_VAL 0x00010504 -#define CFG_MCATT0_VAL 0x00010504 -#define CFG_MCATT1_VAL 0x00010504 -#define CFG_MCIO0_VAL 0x00004715 -#define CFG_MCIO1_VAL 0x00004715 - -#define _LED 0x08000010 -#define LED_BLANK 0x08000040 - -/* - * FLASH and environment organization - */ -#ifndef CFG_NO_FLASH -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ - -/* timeout values are in ticks */ -#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */ -#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */ - - -/* NOTE: many default partitioning schemes assume the kernel starts at the - * second sector, not an environment. You have been warned! - */ -#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE -#endif /* #ifndef CFG_NO_FLASH */ +#define CFG_NO_FLASH 1 -/* #define CFG_ENV_IS_NOWHERE */ #define CFG_ENV_IS_IN_NAND 1 #define CFG_ENV_OFFSET 0x40000 +#define CFG_ENV_OFFSET_REDUND 0x44000 #define CFG_ENV_SIZE 0x4000 #endif /* __CONFIG_H */ diff --git a/include/crc.h b/include/crc.h new file mode 100644 index 0000000..63399bf --- /dev/null +++ b/include/crc.h @@ -0,0 +1,101 @@ +//========================================================================== +// +// crc.h +// +// Interface for the CRC algorithms. +// +//========================================================================== +//####ECOSGPLCOPYRIGHTBEGIN#### +// ------------------------------------------- +// This file is part of eCos, the Embedded Configurable Operating System. +// Copyright (C) 2002 Andrew Lunn +// +// eCos is free software; you can redistribute it and/or modify it under +// the terms of the GNU General Public License as published by the Free +// Software Foundation; either version 2 or (at your option) any later version. +// +// eCos is distributed in the hope that it will be useful, but WITHOUT ANY +// WARRANTY; without even the implied warranty of MERCHANTABILITY or +// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License +// for more details. +// +// You should have received a copy of the GNU General Public License along +// with eCos; if not, write to the Free Software Foundation, Inc., +// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. +// +// As a special exception, if other files instantiate templates or use macros +// or inline functions from this file, or you compile this file and link it +// with other works to produce a work based on this file, this file does not +// by itself cause the resulting work to be covered by the GNU General Public +// License. However the source code for this file must still be made available +// in accordance with section (3) of the GNU General Public License. +// +// This exception does not invalidate any other reasons why a work based on +// this file might be covered by the GNU General Public License. +// +// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc. +// at http://sources.redhat.com/ecos/ecos-license/ +// ------------------------------------------- +//####ECOSGPLCOPYRIGHTEND#### +//========================================================================== +//#####DESCRIPTIONBEGIN#### +// +// Author(s): Andrew Lunn +// Contributors: Andrew Lunn +// Date: 2002-08-06 +// Purpose: +// Description: +// +// This code is part of eCos (tm). +// +//####DESCRIPTIONEND#### +// +//========================================================================== + +#ifndef _SERVICES_CRC_CRC_H_ +#define _SERVICES_CRC_CRC_H_ + +#include <linux/types.h> + +#ifndef __externC +# ifdef __cplusplus +# define __externC extern "C" +# else +# define __externC extern +# endif +#endif + +// Compute a CRC, using the POSIX 1003 definition +extern uint32_t +cyg_posix_crc32(unsigned char *s, int len); + +// Gary S. Brown's 32 bit CRC + +extern uint32_t +cyg_crc32(unsigned char *s, int len); + +// Gary S. Brown's 32 bit CRC, but accumulate the result from a +// previous CRC calculation + +extern uint32_t +cyg_crc32_accumulate(uint32_t crc, unsigned char *s, int len); + +// Ethernet FCS Algorithm + +extern uint32_t +cyg_ether_crc32(unsigned char *s, int len); + +// Ethernet FCS algorithm, but accumulate the result from a previous +// CRC calculation. + +extern uint32_t +cyg_ether_crc32_accumulate(uint32_t crc, unsigned char *s, int len); + +// 16 bit CRC with polynomial x^16+x^12+x^5+1 + +extern uint16_t cyg_crc16(unsigned char *s, int len); + +#endif // _SERVICES_CRC_CRC_H_ + + + diff --git a/include/da9030.h b/include/da9030.h new file mode 100644 index 0000000..41108b9 --- /dev/null +++ b/include/da9030.h @@ -0,0 +1,106 @@ +/* + * (C) Copyright 2006 DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* DA9030 register definitions */ +#define CID 0x00 +#define EVENT_A 0x01 +#define EVENT_B 0x02 +#define EVENT_C 0x03 +#define STATUS 0x04 +#define IRQ_MASK_A 0x05 +#define IRQ_MASK_B 0x06 +#define IRQ_MASK_C 0x07 +#define SYS_CONTROL_A 0x08 +#define SYS_CONTROL_B 0x09 +#define FAULT_LOG 0x0A +#define LDO_10_11 0x10 +#define LDO_15 0x11 +#define LDO_14_16 0x12 +#define LDO_18_19 0x13 +#define LDO_17_SIMCP0 0x14 +#define BUCK2_DVC1 0x15 +#define BUCK2_DVC2 0x16 +#define REG_CONTROL_1_17 0x17 +#define REG_CONTROL_2_18 0x18 +#define USBPUMP 0x19 +#define SLEEP_CONTROL 0x1A +#define STARTUP_CONTROL 0x1B +#define LED1_CONTROL 0x20 +#define LED2_CONTROL 0x21 +#define LED3_CONTROL 0x22 +#define LED4_CONTROL 0x23 +#define LEDPC_CONTROL 0x24 +#define WLED_CONTROL 0x25 +#define MISC_CONTROLA 0x26 +#define MISC_CONTROLB 0x27 +#define CHARGE_CONTROL 0x28 +#define CCTR_CONTROL 0x29 +#define TCTR_CONTROL 0x2A +#define CHARGE_PULSE 0x2B + +/* ... some missing ...*/ + +#define LDO1 0x90 +#define LDO2_3 0x91 +#define LDO4_5 0x92 +#define LDO6_SIMCP 0x93 +#define LDO7_8 0x94 +#define LDO9_12 0x95 +#define BUCK 0x96 +#define REG_CONTROL_1_97 0x97 +#define REG_CONTROL_2_98 0x98 +#define REG_SLEEP_CONTROL1 0x99 +#define REG_SLEEP_CONTROL2 0x9A +#define REG_SLEEP_CONTROL3 0x9B +#define ADC_MAN_CONTROL 0xA0 +#define ADC_AUTO_CONTROL 0xA1 +#define VBATMON 0xA2 +#define VBATMONTXMON 0xA3 +#define TBATHIGHP 0xA4 +#define TBATHIGHN 0xA5 +#define TBATLOW 0xA6 +#define MAN_RES 0xB0 +#define VBAT_RES 0xB1 +#define VBATMIN_RES 0xB2 +#define VBATMINTXON_RES 0xB3 +#define ICHMAX_RES 0xB4 +#define ICHMIN_RES 0xB5 +#define ICHAVERAGE_RES 0xB6 +#define VCHMAX_RES 0xB7 +#define VCHMIN_RES 0xB8 +#define TBAT_RES 0xB9 +#define ADC_IN4_RES 0xBA + +#define STATUS_ONKEY_N 0x1 /* current ONKEY_N value */ +#define STATUS_PWREN1 (1<<1) /* PWREN1 value */ +#define STATUS_EXTON (1<<2) /* EXTON value */ +#define STATUS_CHDET (1<<3) /* Charger detection status */ +#define STATUS_TBAT (1<<4) /* Battery over/under temperature status */ +#define STATUS_VBATMON (1<<5) /* VBATMON comparison status */ +#define STATUS_VBATMONTXON (1<<6) /* VBATMONTXON comparison status */ +#define STATUS_CHIOVER (1<<7) /* Charge overcurrent */ + +#define SYS_CONTROL_A_SLEEP_N_PIN_ENABLE 0x1 +#define SYS_CONTROL_A_SHUT_DOWN (1<<1) +#define SYS_CONTROL_A_HWRES_ENABLE (1<<2) +#define SYS_CONTROL_A_WDOG_ACTION (1<<3) +#define SYS_CONTROL_A_WATCHDOG (1<<7) diff --git a/include/environment.h b/include/environment.h index bb10964..422f800 100644 --- a/include/environment.h +++ b/include/environment.h @@ -69,6 +69,18 @@ # endif #endif /* CFG_ENV_IS_IN_FLASH */ +#if defined(CFG_ENV_IS_IN_NAND) +# ifndef CFG_ENV_OFFSET +# error "Need to define CFG_ENV_OFFSET when using CFG_ENV_IS_IN_NAND" +# endif +# ifndef CFG_ENV_SIZE +# error "Need to define CFG_ENV_SIZE when using CFG_ENV_IS_IN_NAND" +# endif +# ifdef CFG_ENV_OFFSET_REDUND +# define CFG_REDUNDAND_ENVIRONMENT +# endif +#endif /* CFG_ENV_IS_IN_NAND */ + #ifdef CFG_REDUNDAND_ENVIRONMENT # define ENV_HEADER_SIZE (sizeof(unsigned long) + 1) diff --git a/include/xyzModem.h b/include/xyzModem.h new file mode 100644 index 0000000..a62a174 --- /dev/null +++ b/include/xyzModem.h @@ -0,0 +1,112 @@ +//========================================================================== +// +// xyzModem.h +// +// RedBoot stream handler for xyzModem protocol +// +//========================================================================== +//####ECOSGPLCOPYRIGHTBEGIN#### +// ------------------------------------------- +// This file is part of eCos, the Embedded Configurable Operating System. +// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc. +// Copyright (C) 2002 Gary Thomas +// +// eCos is free software; you can redistribute it and/or modify it under +// the terms of the GNU General Public License as published by the Free +// Software Foundation; either version 2 or (at your option) any later version. +// +// eCos is distributed in the hope that it will be useful, but WITHOUT ANY +// WARRANTY; without even the implied warranty of MERCHANTABILITY or +// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License +// for more details. +// +// You should have received a copy of the GNU General Public License along +// with eCos; if not, write to the Free Software Foundation, Inc., +// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. +// +// As a special exception, if other files instantiate templates or use macros +// or inline functions from this file, or you compile this file and link it +// with other works to produce a work based on this file, this file does not +// by itself cause the resulting work to be covered by the GNU General Public +// License. However the source code for this file must still be made available +// in accordance with section (3) of the GNU General Public License. +// +// This exception does not invalidate any other reasons why a work based on +// this file might be covered by the GNU General Public License. +// +// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc. +// at http://sources.redhat.com/ecos/ecos-license/ +// ------------------------------------------- +//####ECOSGPLCOPYRIGHTEND#### +//========================================================================== +//#####DESCRIPTIONBEGIN#### +// +// Author(s): gthomas +// Contributors: gthomas +// Date: 2000-07-14 +// Purpose: +// Description: +// +// This code is part of RedBoot (tm). +// +//####DESCRIPTIONEND#### +// +//========================================================================== + +#ifndef _XYZMODEM_H_ +#define _XYZMODEM_H_ + +#define xyzModem_xmodem 1 +#define xyzModem_ymodem 2 +// Don't define this until the protocol support is in place +//#define xyzModem_zmodem 3 + +#define xyzModem_access -1 +#define xyzModem_noZmodem -2 +#define xyzModem_timeout -3 +#define xyzModem_eof -4 +#define xyzModem_cancel -5 +#define xyzModem_frame -6 +#define xyzModem_cksum -7 +#define xyzModem_sequence -8 + +#define xyzModem_close 1 +#define xyzModem_abort 2 + + +#ifdef REDBOOT +extern getc_io_funcs_t xyzModem_io; +#else +#define CYGNUM_CALL_IF_SET_COMM_ID_QUERY_CURRENT +#define CYGACC_CALL_IF_SET_CONSOLE_COMM(x) + +#define diag_vprintf vprintf +#define diag_printf printf +#define diag_vsprintf vsprintf + +#define CYGACC_CALL_IF_DELAY_US(x) udelay(x) + +typedef struct { + char *filename; + int mode; + int chan; +#ifdef CYGPKG_REDBOOT_NETWORKING + struct sockaddr_in *server; +#endif +} connection_info_t; + +typedef unsigned int bool; + +#define false 0 +#define true 1 + +#endif + + +int xyzModem_stream_open(connection_info_t *info, int *err); +void xyzModem_stream_close(int *err); +void xyzModem_stream_terminate(bool method, int (*getc)(void)); +int xyzModem_stream_read(char *buf, int size, int *err); +char *xyzModem_error(int err); + +#endif // _XYZMODEM_H_ |