summaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/commproc.h62
-rw-r--r--include/configs/v37.h381
-rw-r--r--include/flash.h5
-rw-r--r--include/version.h2
4 files changed, 430 insertions, 20 deletions
diff --git a/include/commproc.h b/include/commproc.h
index 42db998..159c294 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1100,6 +1100,34 @@ typedef struct scc_enet {
#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
#endif /* CONFIG_MHPC */
+/*** NETVIA *******************************************************/
+
+#if defined(CONFIG_NETVIA)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
+
+#define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
+#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002f00)
+
+#endif /* CONFIG_NETVIA */
+
/*** RPXCLASSIC *****************************************************/
#ifdef CONFIG_RPXCLASSIC
@@ -1309,31 +1337,27 @@ typedef struct scc_enet {
# endif /* CONFIG_FEC_ENET */
#endif /* CONFIG_TQM860L, CONFIG_TQM855L */
-#if defined(CONFIG_NETVIA)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
+/*** V37 **********************************************************/
+
+#ifdef CONFIG_V37
+/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of
+ * this may be unique to the Marel V37 configuration.
+ * Note TENA is on Port B.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
-#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+#define PA_ENET_RXD ((ushort)0x0004)
+#define PA_ENET_TXD ((ushort)0x0008)
+#define PA_ENET_TCLK ((ushort)0x0400)
+#define PA_ENET_RCLK ((ushort)0x0200)
+#define PB_ENET_TENA ((uint)0x00002000)
+#define PC_ENET_CLSN ((ushort)0x0040)
+#define PC_ENET_RENA ((ushort)0x0080)
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00)
-
-#endif /* CONFIG_NETVIA */
+#define SICR_ENET_CLKRT ((uint)0x00002e00)
+#endif /* CONFIG_V37 */
/*********************************************************************/
diff --git a/include/configs/v37.h b/include/configs/v37.h
new file mode 100644
index 0000000..f527440
--- /dev/null
+++ b/include/configs/v37.h
@@ -0,0 +1,381 @@
+/*
+ * (C) Copyright 2000, 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
+#define CONFIG_V37 1 /* ...on a Marel V37 board */
+
+#define CONFIG_LCD
+#define CONFIG_SHARP_LQ084V1DG21
+#undef CONFIG_LCD_LOGO
+
+/*-----------------------------------------------------------------------------
+ * I2C Configuration
+ *-----------------------------------------------------------------------------
+ */
+#define CONFIG_I2C 1
+#define CFG_I2C_SLAVE 0x2
+
+#define CONFIG_8xx_CONS_SMC1 1
+#undef CONFIG_8xx_CONS_SMC2 /* Console is on SMC2 */
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600 /* console baudrate = 115kbps */
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
+#endif
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_BOOTCOMMAND \
+ "tftpboot; " \
+ "setenv bootargs console=tty0 " \
+ "root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_DATE )
+
+
+/* Flash banks JFFS2 should use */
+#define CFG_JFFS2_FIRST_BANK 1
+#define CFG_JFFS2_NUM_BANKS 1
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE0 0x40000000
+#define CFG_FLASH_BASE1 0x60000000
+#define CFG_FLASH_BASE CFG_FLASH_BASE1
+
+#if defined(DEBUG)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE0
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_NVRAM 1
+#define CFG_ENV_ADDR 0x80000000/* Address of Environment */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+#define CFG_ENV_OFFSET 0
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR 0xFFFFFF88
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_FRC | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+/*
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+*/
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ */
+/* up to 50 MHz we use a 1:1 clock */
+#define CFG_PLPRCR ( (1524 << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TMIST | PLPRCR_TEXPS )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+/* up to 50 MHz we use a 1:1 clock */
+#define CFG_SCCR (SCCR_COM00 | SCCR_TBS)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_PCMCIA /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0x0082000F
+/*#define CFG_DER 0*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */
+
+#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
+
+#define CFG_OR_TIMING_FLASH 0xF56
+
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V)
+
+#define CFG_OR5_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR5_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V)
+
+/*
+ * BR1 and OR1 (Battery backed SRAM)
+ */
+#define CFG_BR1_PRELIM 0x80000401
+#define CFG_OR1_PRELIM 0xFFC00736
+
+/*
+ * BR2 and OR2 (SDRAM)
+ */
+#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB */
+
+#define CFG_OR_TIMING_SDRAM 0x00000A00
+
+#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/* Marel V37 mem setting */
+
+#define CFG_BR3_CAN 0xC0000401
+#define CFG_OR3_CAN 0xFFFF0724
+
+/*
+#define CFG_BR3_PRELIM 0xFA400001
+#define CFG_OR3_PRELIM 0xFFFF8910
+#define CFG_BR4_PRELIM 0xFA000401
+#define CFG_OR4_PRELIM 0xFFFE0970
+*/
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+
+/*
+ * Refresh clock Prescalar
+ */
+#define CFG_MPTPR MPTPR_PTP_DIV16
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \
+ MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+
+#endif /* __CONFIG_H */
diff --git a/include/flash.h b/include/flash.h
index 3150e3d..b4c8bad 100644
--- a/include/flash.h
+++ b/include/flash.h
@@ -111,6 +111,7 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
#define INTEL_MANUFACT 0x00890089 /* INTEL manuf. ID in D23..D16, D7..D0 */
#define INTEL_ALT_MANU 0x00B000B0 /* alternate INTEL namufacturer ID */
#define MX_MANUFACT 0x00C200C2 /* MXIC manuf. ID in D23..D16, D7..D0 */
+#define TOSH_MANUFACT 0x00980098 /* TOSHIBA manuf. ID in D23..D16, D7..D0 */
/* Micron Technologies (INTEL compat.) */
#define MT_ID_28F400_T 0x44704470 /* 28F400B3 ID ( 4 M, top boot sector) */
@@ -206,6 +207,9 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
#define SHARP_ID_28F008SC 0xA6A6A6A6 /* LH28F008SCT-L12 1Mx8, 16 64k blocks */
/* LH28F008SCR-L85 1Mx8, 16 64k blocks */
+#define TOSH_ID_FVT160 0xC2 /* TC58FVT160 ID (16 M, top ) */
+#define TOSH_ID_FVB160 0x43 /* TC58FVT160 ID (16 M, bottom ) */
+
/*-----------------------------------------------------------------------
* Internal FLASH identification codes
*
@@ -301,6 +305,7 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
#define FLASH_MAN_BM 0x00020000 /* Bright Microelectronics */
#define FLASH_MAN_MX 0x00030000 /* MXIC */
#define FLASH_MAN_STM 0x00040000
+#define FLASH_MAN_TOSH 0x00050000 /* Toshiba */
#define FLASH_MAN_SST 0x00100000
#define FLASH_MAN_INTEL 0x00300000
#define FLASH_MAN_MT 0x00400000
diff --git a/include/version.h b/include/version.h
index b501028..5249f2a 100644
--- a/include/version.h
+++ b/include/version.h
@@ -24,6 +24,6 @@
#ifndef __VERSION_H__
#define __VERSION_H__
-#define U_BOOT_VERSION "U-Boot 0.2.1"
+#define U_BOOT_VERSION "U-Boot 0.2.2"
#endif /* __VERSION_H__ */