summaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/configs/MPC8540ADS.h129
-rw-r--r--include/configs/MPC8560ADS.h141
-rw-r--r--include/configs/stxgp3.h196
-rw-r--r--include/e500.h15
4 files changed, 227 insertions, 254 deletions
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index b967b1e..74e15c7 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -49,12 +49,6 @@
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-/*
- * Use Localbus SDRAM to emulate flash before we can program the flash.
- * Normally you need a flash-boot image(u-boot.bin).
- * If unsure #undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
/*
* sysclk for MPC85xx
@@ -64,24 +58,17 @@
* 66000000
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here. The board, however, can run and
- * defaults to 66Mhz. In any event, this value must match the settings
- * of SW15[1] and SW17[8], and likely SW6[0:1], the SYSCLK as well.
- *
- * SW17[8] ------+ SW6
- * SW15[1] ----+ | [0:1]
- * V V V V
- * 33MHz 1 1 1 0
- * 66MHz 0 0 0 1
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz. In any event, this value
+ * must match the settings of some switches. Details can be found
+ * in the README.mpc85xxads.
*/
-#define CONFIG_SYS_CLK_FREQ 66000000
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-#define CONFIG_DDR_SETTING /* manually set up DDR parameters */
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 33000000
#endif
+
/*
* These can be toggled for performance analysis, otherwise use default.
*/
@@ -104,27 +91,42 @@
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR parameters
+ */
+ #define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+ #define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+ #define CFG_DDR_CS0_CONFIG 0x80000002
+ #define CFG_DDR_TIMING_1 0x37344321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+ #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+ #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+ #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
+#endif
+
/*
* SDRAM on the Local Bus
*/
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
-#else
#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#endif
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
-#else /* Boot from real Flash */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
-#endif
#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
@@ -142,20 +144,9 @@
#undef CFG_RAMBOOT
#endif
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#undef CONFIG_CLOCKS_IN_MHZ
-#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
-#endif
-
/*
* Local Bus Definitions
@@ -244,28 +235,27 @@
* SDRAM Controller configuration sequence.
*/
#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL) /*0x2861b723*/
+ | CFG_LBC_LSDMR_OP_PCHALL)
#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+ | CFG_LBC_LSDMR_OP_ARFRSH)
#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+ | CFG_LBC_LSDMR_OP_ARFRSH)
#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW) /*0x1861b723*/
+ | CFG_LBC_LSDMR_OP_MRW)
#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL) /*0x4061b723*/
+ | CFG_LBC_LSDMR_OP_NORMAL)
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#else
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#endif
+/*
+ * 32KB, 8-bit wide for ADS config reg
+ */
+#define CFG_BR4_PRELIM 0xf8000801
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
@@ -321,7 +311,7 @@
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
@@ -347,13 +337,15 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_FEC 1
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+
+#define CONFIG_MPC85XX_FEC 1
+#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
+
#define CONFIG_ETHPRIME "MOTO ENET0"
#endif /* CONFIG_TSEC_ENET */
@@ -363,27 +355,21 @@
* Environment
*/
#ifndef CFG_RAMBOOT
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #endif
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
-#define CFG_ENV_SIZE 0x2000
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+#if defined(CFG_RAMBOOT)
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
| CFG_CMD_PING \
@@ -462,9 +448,10 @@
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/*****************************/
-/* Environment Configuration */
-/*****************************/
+
+/*
+ * Environment Configuration
+ */
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
@@ -490,13 +477,13 @@
#define CONFIG_BAUDRATE 115200
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=400000\0" \
"ramdiskfile=your.ramdisk.u-boot\0"
-#define CONFIG_NFSBOOTCOMMAND \
+#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index f681b50..3876747 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -45,17 +45,11 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-/*
- * Use Localbus SDRAM to emulate flash before we can program the flash.
- * Normally you need a flash-boot image(u-boot.bin).
- * If unsure #undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
/*
* sysclk for MPC85xx
@@ -65,24 +59,17 @@
* 66000000
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here. The board, however, can run and
- * defaults to 66Mhz. In any event, this value must match the settings
- * of SW15[1] and SW17[8], and likely SW6[0:1], the SYSCLK as well.
- *
- * SW17[8] ------+ SW6
- * SW15[1] ----+ | [0:1]
- * V V V V
- * 33MHz 1 1 1 0
- * 66MHz 0 0 0 1
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz. In any event, this value
+ * must match the settings of some switches. Details can be found
+ * in the README.mpc85xxads.
*/
-#define CONFIG_SYS_CLK_FREQ 66000000
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-#define CONFIG_DDR_SETTING /* manually set up DDR parameters */
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 33000000
#endif
+
/*
* These can be toggled for performance analysis, otherwise use default.
*/
@@ -94,7 +81,7 @@
#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
-#undef CFG_DRAM_TEST /* memory test, takes time */
+#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
@@ -104,30 +91,45 @@
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR parameters
+ */
+ #define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+ #define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+ #define CFG_DDR_CS0_CONFIG 0x80000002
+ #define CFG_DDR_TIMING_1 0x37344321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+ #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+ #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+ #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
+#endif
+
/*
* SDRAM on the Local Bus
*/
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
-#else
#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#endif
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
-#else /* Boot from real Flash */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
-#endif
#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
@@ -145,20 +147,9 @@
#undef CFG_RAMBOOT
#endif
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#undef CONFIG_CLOCKS_IN_MHZ
-#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
-#endif
-
/*
* Local Bus Definitions
@@ -247,28 +238,27 @@
* SDRAM Controller configuration sequence.
*/
#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL) /*0x2861b723*/
+ | CFG_LBC_LSDMR_OP_PCHALL)
#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+ | CFG_LBC_LSDMR_OP_ARFRSH)
#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+ | CFG_LBC_LSDMR_OP_ARFRSH)
#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW) /*0x1861b723*/
+ | CFG_LBC_LSDMR_OP_MRW)
#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL) /*0x4061b723*/
+ | CFG_LBC_LSDMR_OP_NORMAL)
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#else
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#endif
+/*
+ * 32KB, 8-bit wide for ADS config reg
+ */
+#define CFG_BR4_PRELIM 0xf8000801
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
@@ -295,11 +285,11 @@
#endif
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
/* RapidIO MMU */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
@@ -320,7 +310,7 @@
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
@@ -402,34 +392,28 @@
* Environment
*/
#ifndef CFG_RAMBOOT
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #endif
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
-#define CFG_ENV_SIZE 0x2000
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+#if defined(CFG_RAMBOOT)
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
| CFG_CMD_PING \
+ | CFG_CMD_PCI \
| CFG_CMD_I2C) \
& \
- ~(CFG_CMD_ENV \
+ ~(CFG_CMD_ENV \
| CFG_CMD_LOADS))
#elif defined(CONFIG_TSEC_ENET)
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
@@ -510,6 +494,11 @@
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+
+/*
+ * Environment Configuration
+ */
+
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
@@ -529,18 +518,18 @@
#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=400000\0" \
"ramdiskfile=your.ramdisk.u-boot\0"
-#define CONFIG_NFSBOOTCOMMAND \
+#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 8460944..f5b4836 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -39,7 +39,6 @@
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
#define CONFIG_MPC8560 1 /* MPC8560 specific */
#define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/
@@ -49,15 +48,12 @@
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-
-#if defined(CONFIG_MPC85xx_REV1)
#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#endif
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
+/* sysclk for MPC85xx
*/
-#undef CONFIG_RAM_AS_FLASH
#define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */
@@ -65,55 +61,29 @@
*/
#define CONFIG_SHOW_ACTIVITY 1
-#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
-#define CONFIG_DDR_SETTING
-#endif
-
-/* below can be toggled for performance analysis. otherwise use default */
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-
-/* GPPP supports up to 2G of DRAM. Allocate up to 1G until we get
- * a chance to try it out. Actual size is always read from sdram eeprom.
- */
-#define CFG_SDRAM_SIZE 1024 /* DDR is 1GB */
/* Localbus SDRAM is an option, not all boards have it.
-*/
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
-#else
-#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
-#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+ * This address, however, is used to configure a 256M local bus
+ * window that includes the Config latch below.
+ */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
-#else /* Boot from real Flash */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
-#endif
#define CFG_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
@@ -123,7 +93,7 @@
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/* The configuration latch is Chip Select 1.
- * It's an 8-bit latch in the upper 8 bits of the word.
+ * It's an 8-bit latch in the lower 8 bits of the word.
*/
#define CFG_BR1_PRELIM 0xfc001801 /* 32-bit port */
#define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */
@@ -146,17 +116,18 @@
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */
+/*
+ * DDR Setup
+ */
-#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
-#endif
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */
#undef CONFIG_CLOCKS_IN_MHZ
@@ -213,37 +184,65 @@
#undef CFG_I2C_NOPROBES
#endif
-#define CFG_PCI_MEM_BASE 0xe0000000
-#define CFG_PCI_MEM_PHYS 0xe0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
+/* RapdIO Map configuration, mapped 1:1.
+*/
+#define CFG_RIO_MEM_BASE 0xc0000000
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x200000000 /* 512 M */
+
+/* Standard 8560 PCI addressing, mapped 1:1.
+*/
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x01000000 /* 16 M */
#if defined(CONFIG_PCI) /* PCI Ethernet card */
+
#define CONFIG_NET_MULTI
-#define CONFIG_EEPRO100
-#undef CONFIG_TULIP
#define CONFIG_PCI_PNP /* do pci plug-and-play */
- #if !defined(CONFIG_PCI_PNP)
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
- #endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */
- #define CFG_PCI_SUBSYS_DEVICEID 0x0003
-#else
- #define CFG_PCI_SUBSYS_DEVICEID 0x0009
#endif
-#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
+
+#undef CONFIG_PCI_SCAN_SHOW
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
+#endif
+
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 8 /* PHY address */
+
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC2 1
+#undef CONFIG_MPS85XX_FEC
+
+#define TSEC1_PHY_ADDR 2
+#define TSEC2_PHY_ADDR 4
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define CONFIG_ETHPRIME "MOTO ENET0"
+
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
+
#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
- #if (CONFIG_ETHER_INDEX == 2)
+
+#if (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
* - Tx-CLK is CLK14
@@ -259,59 +258,41 @@
#define CFG_FCC_PSMR 0
#endif
#define FETH2_RST 0x01
- #elif (CONFIG_ETHER_INDEX == 3)
+#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
#define FETH3_RST 0x80
- #endif /* CONFIG_ETHER_INDEX */
+#endif /* CONFIG_ETHER_INDEX */
+
+/* MDIO is done through the TSEC0 control.
+*/
#define CONFIG_MII /* MII PHY management */
#undef CONFIG_BITBANGMII /* bit-bang MII PHY management */
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT 2 /* Port C */
-#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
-#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
-#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
-#define MIIDELAY udelay(1)
#endif
/* Environment */
/* We use the top boot sector flash, so we have some 16K sectors for env
- * But....functions don't seem smart enough yet.
*/
#ifndef CFG_RAMBOOT
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000)
#define CFG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */
- #endif
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
-#define CFG_ENV_SIZE 0x2000
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400"
-#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xff900000"
+#define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000"
#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+#if defined(CFG_RAMBOOT)
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \
CFG_CMD_PING | CFG_CMD_I2C) & \
@@ -329,13 +310,13 @@
#else
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C)
+ CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
#elif defined(CONFIG_TSEC_ENET)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_MII | CFG_CMD_I2C)
+ CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C)
#elif defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C)
+ CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
#endif
#endif
#include <cmd_confdefs.h>
@@ -387,9 +368,9 @@
/*Note: change below for your network setting!!! */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a
+#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b
+#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c
#endif
#define CONFIG_SERVERIP 192.168.85.1
@@ -399,5 +380,6 @@
#define CONFIG_HOSTNAME STX_GP3
#define CONFIG_ROOTPATH /gppproot
#define CONFIG_BOOTFILE uImage
+#define CONFIG_LOADADDR 0x1000000
#endif /* __CONFIG_H */
diff --git a/include/e500.h b/include/e500.h
index 5489ba2..8e3bf8c 100644
--- a/include/e500.h
+++ b/include/e500.h
@@ -20,14 +20,29 @@ typedef struct
* initial memory mapping like legacy BAT registers do. Usually we
* use four MAS registers(MAS0-3) to operate on TLB1 entries.
*
+ * While there are 16 Entries with variable Page Sizes in TLB1,
+ * there are also 256 Entries with fixed 4K pages in TLB0.
+ *
* We also need LAWs(Local Access Window) to associate a range of
* the local 32-bit address space with a particular target interface
* such as PCI/PCI-X, RapidIO, Local Bus and DDR SDRAM.
*
* We put TLB1/LAW code here because memory mapping is board-specific
* instead of cpu-specific.
+ *
+ * While these macros are all nominally for TLB1 by name, they can
+ * also be used for TLB0 as well.
*/
+
+/*
+ * Convert addresses to Effective and Real Page Numbers.
+ * Grab the high 20-bits and shift 'em down, dropping the "byte offset".
+ */
+#define E500_TLB_EPN(addr) (((addr) >> 12) & 0xfffff)
+#define E500_TLB_RPN(addr) (((addr) >> 12) & 0xfffff)
+
+
/* MAS0
* tlbsel(TLB Select):0,1
* esel(Entry Select): 0,1,2,...,15 for TLB1