diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/ZPC1900.h | 261 |
1 files changed, 0 insertions, 261 deletions
diff --git a/include/configs/ZPC1900.h b/include/configs/ZPC1900.h deleted file mode 100644 index d76a140..0000000 --- a/include/configs/ZPC1900.h +++ /dev/null @@ -1,261 +0,0 @@ -/* - * Copyright (C) 2003-2005 Arabella Software Ltd. - * Yuli Barcohen <yuli@arabellasw.com> - * - * U-Boot configuration for Zephyr Engineering ZPC.1900 board. - * This port was developed and tested on Revision C board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_ZPC1900 1 /* ...on Zephyr ZPC.1900 board */ - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CPU_ID_STR "MPC8265" -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */ -#define CONFIG_ENV_OVERWRITE - -/* - * Select serial console configuration - * - * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - */ -#define CONFIG_CONS_ON_SMC /* Console is on SMC */ -#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ -#undef CONFIG_CONS_NONE /* It's not on external UART */ -#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */ - -/* - * Select ethernet configuration - * - * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, - * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for - * SCC, 1-3 for FCC) - * - * If CONFIG_ETHER_NONE is defined, then either the ethernet routines - * must be defined elsewhere (as for the console), or CONFIG_CMD_NET - * must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */ -#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */ -#undef CONFIG_ETHER_NONE /* No external Ethernet */ - -#ifdef CONFIG_ETHER_ON_FCC - -#define CONFIG_ETHER_INDEX 2 /* FCC2 is used for Ethernet */ - -#if (CONFIG_ETHER_INDEX == 2) -/* - * - Rx clock is CLK13 - * - Tx clock is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Full duplex - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_INDEX */ - -#define CONFIG_MII /* MII PHY management */ -#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */ -/* - * GPIO pins used for bit-banged MII communications - */ -#define MDIO_PORT 2 /* Port C */ -#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) -#define MDC_DECLARE MDIO_DECLARE - -#define MDIO_ACTIVE (iop->pdir |= 0x00400000) -#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) -#define MDIO_READ ((iop->pdat & 0x00400000) != 0) - -#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 - -#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - -#define MIIDELAY udelay(1) - -#endif /* CONFIG_ETHER_ON_FCC */ - -#ifndef CONFIG_8260_CLKIN -#define CONFIG_8260_CLKIN 66666666 /* in Hz */ -#endif - -#define CONFIG_BAUDRATE 38400 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING - - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_BOOTCOMMAND "dhcp;bootm" /* autoboot command */ -#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=:::::eth0:dhcp" - -#if defined(CONFIG_CMD_KGDB) -#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ -#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ -#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ -#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ -#endif - -#define CONFIG_BZIP2 /* include support for bzip2 compressed images */ -#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x03800000 /* 1 ... 56 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 64 - -#define CONFIG_SYS_IMMR 0xF0000000 -#define CONFIG_SYS_LSDRAM_BASE 0xFC000000 -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_BCSR 0xFEA00000 -#define CONFIG_SYS_EEPROM 0xFEB00000 -#define CONFIG_SYS_FLSIMM_BASE 0xFF000000 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE } - -#define BCSR_PCI_MODE 0x01 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Hard reset configuration word */ -#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM | HRCW_BPS01| HRCW_CIP |\ - HRCW_L2CPC10 | HRCW_DPPC00 | HRCW_ISB100 |\ - HRCW_BMS | HRCW_LBPC00 | HRCW_APPC10 |\ - HRCW_MODCK_H0111 \ - ) /* 0x16848207 */ -/* No slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM) -#define CONFIG_ENV_IS_IN_NVRAM 1 -#endif - -#ifdef CONFIG_ENV_IS_IN_FLASH -# define CONFIG_ENV_SECT_SIZE 0x10000 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#else -# define CONFIG_ENV_ADDR (CONFIG_SYS_EEPROM + 0x400) -# define CONFIG_ENV_SIZE 0x1000 -# define CONFIG_SYS_NVRAM_ACCESS_ROUTINE -#endif - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#define CONFIG_SYS_HID0_INIT (HID0_ICFI) -#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) - -#define CONFIG_SYS_HID2 0 - -#define CONFIG_SYS_SIUMCR 0x42200000 -#define CONFIG_SYS_SYPCR 0xFFFFFFC3 -#define CONFIG_SYS_BCR 0x90000000 -#define CONFIG_SYS_SCCR SCCR_DFBRG01 - -#define CONFIG_SYS_RMR RMR_CSRE -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) -#define CONFIG_SYS_RCCR 0 - -#define CONFIG_SYS_PSDMR /* 0x834DA43B */0x014DA43A -#define CONFIG_SYS_PSRT 0x0F/* 0x0C */ -#define CONFIG_SYS_LSDMR 0x0085A562 -#define CONFIG_SYS_LSRT 0x0F -#define CONFIG_SYS_MPTPR 0x4000 - -#define CONFIG_SYS_PSDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00000041) -#define CONFIG_SYS_PSDRAM_OR 0xFC0028C0 -#define CONFIG_SYS_LSDRAM_BR (CONFIG_SYS_LSDRAM_BASE | 0x00001861) -#define CONFIG_SYS_LSDRAM_OR 0xFF803480 - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00000801) -#define CONFIG_SYS_OR0_PRELIM 0xFFE00856 -#define CONFIG_SYS_BR5_PRELIM (CONFIG_SYS_EEPROM | 0x00000801) -#define CONFIG_SYS_OR5_PRELIM 0xFFFF03F6 -#define CONFIG_SYS_BR6_PRELIM (CONFIG_SYS_FLSIMM_BASE | 0x00001801) -#define CONFIG_SYS_OR6_PRELIM 0xFF000856 -#define CONFIG_SYS_BR7_PRELIM (CONFIG_SYS_BCSR | 0x00000801) -#define CONFIG_SYS_OR7_PRELIM 0xFFFF83F6 - -#define CONFIG_SYS_RESET_ADDRESS 0xC0000000 - -#endif /* __CONFIG_H */ |