diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/Total5200.h | 390 | ||||
| -rw-r--r-- | include/mpc5xxx.h | 17 |
2 files changed, 407 insertions, 0 deletions
diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h new file mode 100644 index 0000000..29c627c --- /dev/null +++ b/include/configs/Total5200.h @@ -0,0 +1,390 @@ +/* + * (C) Copyright 2003-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2004 + * Mark Jonas, Freescale Semiconductor, mark.jonas@freescale.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Check valid setting of revision define. + * Total5100 and Total5200 Rev.1 are identical except for the processor. + */ +#if (CONFIG_TOTAL5200_REV!=1 && CONFIG_TOTAL5200_REV!=2) +#error CONFIG_TOTAL5200_REV must be 1 or 2 +#endif + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_TOTAL5200 1 /* ... on Total5200 board */ + +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + + +#ifdef CONFIG_MPC5200 /* MGT5100 PCI is not supported yet. */ +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 +#define CONFIG_PCI_SCAN_SHOW 1 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 + +#define CONFIG_NET_MULTI 1 +#define CONFIG_EEPRO100 1 +#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_NS8382X 1 + +#define ADD_PCI_CMD CFG_CMD_PCI + +#else /* MGT5100 */ + +#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */ + +#endif + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +/* USB */ +#if 1 +#define CONFIG_USB_OHCI +#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT +#define CONFIG_USB_STORAGE +#else +#define ADD_USB_CMD 0 +#endif + +/* + * Supported commands + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_PING | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM | \ + CFG_CMD_FAT | \ + CFG_CMD_IDE | \ + ADD_PCI_CMD | \ + ADD_USB_CMD) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#if (TEXT_BASE == 0xFE000000) /* Boot low */ +# define CFG_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "bootfile=/tftpboot/MPC5200/uImage\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if defined(CONFIG_MPC5200) +/* + * IPB Bus clocking configuration. + */ +#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#endif + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */ + +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70 + +/* + * Flash configuration + */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#if CONFIG_TOTAL5200_REV==2 +# define CFG_MAX_FLASH_BANKS 3 /* max num of flash banks */ +# define CFG_FLASH_BANKS_LIST { CFG_CS5_START, CFG_CS4_START, CFG_BOOTCS_START } +#else +# define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ +# define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#endif +#define CFG_FLASH_EMPTY_INFO +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#if CONFIG_TOTAL5200_REV==1 +# define CFG_FLASH_BASE 0xFE000000 +# define CFG_FLASH_SIZE 0x02000000 +#elif CONFIG_TOTAL5200_REV==2 +# define CFG_FLASH_BASE 0xFA000000 +# define CFG_FLASH_SIZE 0x06000000 +#endif /* CONFIG_TOTAL5200_REV */ + +#if !defined(CFG_LOWBOOT) +# define CFG_ENV_ADDR 0xFE040000 +#else /* CFG_LOWBOOT */ +# define CFG_ENV_ADDR 0xFFF40000 +#endif /* CFG_LOWBOOT */ + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x40000 +#define CFG_ENV_SECT_SIZE 0x40000 +#define CONFIG_ENV_OVERWRITE 1 + +/* + * Memory map + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_DEFAULT_MBAR 0x80000000 +#define CFG_MBAR 0xF0000000 /* 64 kB */ +#define CFG_FPGA_BASE 0xF0010000 /* 64 kB */ +#define CFG_CPLD_BASE 0xF0020000 /* 64 kB */ +#define CFG_LCD_BASE 0xF0100000 /* 2048 kB */ + +/* Use SRAM until RAM will be available */ +#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT 1 +#endif + +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +/* dummy, 7-wire FEC does not have phy address */ +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration + * + * CS1: SDRAM CS1 disabled, gpio_wkup_6 enabled 0 + * Reserved 0 + * ALTs: CAN1/2 on PSC2, SPI on PSC3 00 + * CS7: Interrupt GPIO on PSC3_5 0 + * CS8: Interrupt GPIO on PSC3_4 0 + * ATA: reset default, changed in ATA driver 00 + * IR_USB_CLK: IrDA/USB 48MHz clock gen. int., pin is GPIO 0 + * IRDA: reset default, changed in IrDA driver 000 + * ETHER: reset default, changed in Ethernet driver 0000 + * PCI_DIS: reset default, changed in PCI driver 0 + * USB_SE: reset default, changed in USB driver 0 + * USB: reset default, changed in USB driver 00 + * PSC3: SPI and UART functionality without CD 1100 + * Reserved 0 + * PSC2: CAN1/2 001 + * Reserved 0 + * PSC1: reset default, changed in AC'97 driver 000 + * + */ +#define CFG_GPS_PORT_CONFIG 0x00000C10 + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * Various low-level settings + */ +#if defined(CONFIG_MPC5200) +#define CFG_HID0_INIT HID0_ICE | HID0_ICFI +#define CFG_HID0_FINAL HID0_ICE +#else +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL 0 +#endif + +#if defined (CONFIG_MGT5100) +# define CONFIG_BOARD_EARLY_INIT_R /* switch from CS_BOOT to CS0 */ +#endif + +#if CONFIG_TOTAL5200_REV==1 +# define CFG_BOOTCS_START CFG_FLASH_BASE +# define CFG_BOOTCS_SIZE 0x02000000 /* 32 MB */ +# define CFG_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CFG_CS0_START CFG_FLASH_BASE +# define CFG_CS0_SIZE 0x02000000 /* 32 MB */ +#else +# define CFG_BOOTCS_START (CFG_CS4_START + CFG_CS4_SIZE) +# define CFG_BOOTCS_SIZE 0x02000000 /* 32 MB */ +# define CFG_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CFG_CS4_START (CFG_CS5_START + CFG_CS5_SIZE) +# define CFG_CS4_SIZE 0x02000000 /* 32 MB */ +# define CFG_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CFG_CS5_START CFG_FLASH_BASE +# define CFG_CS5_SIZE 0x02000000 /* 32 MB */ +# define CFG_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +#endif + +#define CFG_CS1_START CFG_FPGA_BASE +#define CFG_CS1_SIZE 0x00010000 /* 64 kB */ +#define CFG_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */ + +#define CFG_CS2_START CFG_LCD_BASE +#define CFG_CS2_SIZE 0x00200000 /* 2048 kB */ +#define CFG_CS2_CFG 0x0019FD00 /* 25WS, MX, AL, AA, CE, AS_25, DS_16 */ + +#if CONFIG_TOTAL5200_REV==1 +# define CFG_CS3_START CFG_CPLD_BASE +# define CFG_CS3_SIZE 0x00010000 /* 64 kB */ +# define CFG_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */ +#else +# define CFG_CS3_START CFG_CPLD_BASE +# define CFG_CS3_SIZE 0x00010000 /* 64 kB */ +# define CFG_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */ +#endif + +#define CFG_CS_BURST 0x00000000 +#define CFG_CS_DEADCYCLE 0x33333333 + +/*----------------------------------------------------------------------- + * USB stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_USB_CLOCK 0x0001BBBB +#define CONFIG_USB_CONFIG 0x00001000 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_IDE_RESET /* reset for ide supported */ +#define CONFIG_IDE_PREINIT + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CFG_ATA_STRIDE 4 + +#endif /* __CONFIG_H */ diff --git a/include/mpc5xxx.h b/include/mpc5xxx.h index fb0e41a..e5c8c02 100644 --- a/include/mpc5xxx.h +++ b/include/mpc5xxx.h @@ -165,6 +165,23 @@ /* GPIO registers */ #define MPC5XXX_GPS_PORT_CONFIG (MPC5XXX_GPIO + 0x0000) +/* Standard GPIO registers (simple, output only and simple interrupt */ +#define MPC5XXX_GPIO_ENABLE (MPC5XXX_GPIO + 0x0004) +#define MPC5XXX_GPIO_ODE (MPC5XXX_GPIO + 0x0008) +#define MPC5XXX_GPIO_DIR (MPC5XXX_GPIO + 0x000c) +#define MPC5XXX_GPIO_DATA_O (MPC5XXX_GPIO + 0x0010) +#define MPC5XXX_GPIO_DATA_I (MPC5XXX_GPIO + 0x0014) +#define MPC5XXX_GPIO_OO_ENABLE (MPC5XXX_GPIO + 0x0018) +#define MPC5XXX_GPIO_OO_DATA (MPC5XXX_GPIO + 0x001C) +#define MPC5XXX_GPIO_SI_ENABLE (MPC5XXX_GPIO + 0x0020) +#define MPC5XXX_GPIO_SI_ODE (MPC5XXX_GPIO + 0x0024) +#define MPC5XXX_GPIO_SI_DIR (MPC5XXX_GPIO + 0x0028) +#define MPC5XXX_GPIO_SI_DATA (MPC5XXX_GPIO + 0x002C) +#define MPC5XXX_GPIO_SI_IEN (MPC5XXX_GPIO + 0x0030) +#define MPC5XXX_GPIO_SI_ITYPE (MPC5XXX_GPIO + 0x0034) +#define MPC5XXX_GPIO_SI_MEN (MPC5XXX_GPIO + 0x0038) +#define MPC5XXX_GPIO_SI_STATUS (MPC5XXX_GPIO + 0x003C) + /* WakeUp GPIO registers */ #define MPC5XXX_WU_GPIO_ENABLE (MPC5XXX_WU_GPIO + 0x0000) #define MPC5XXX_WU_GPIO_ODE (MPC5XXX_WU_GPIO + 0x0004) |