diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/mecp5123.h | 458 |
1 files changed, 458 insertions, 0 deletions
diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h new file mode 100644 index 0000000..0831843 --- /dev/null +++ b/include/configs/mecp5123.h @@ -0,0 +1,458 @@ +/* + * (C) Copyright 2009 Wolfgang Denk <wd@denx.de> + * (C) Copyright 2009, DAVE Srl <www.dave.eu> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * modifications for the MECP5123 by reinhard.arlt@esd-electronics.com + * + */ + +/* + * MECP5123 board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MECP5123 1 +/* + * Memory map for the MECP5123 board: + * + * 0x0000_0000 - 0x1FFF_FFFF DDR RAM (512 MB) + * 0x3000_0000 - 0x3001_FFFF SRAM (128 KB) + * 0x8000_0000 - 0x803F_FFFF IMMR (4 MB) + * 0x8200_0000 - 0x8200_FFFF VPC-3 (64 KB) + * 0xFFC0_0000 - 0xFFFF_FFFF NOR Boot FLASH (64 MB) + */ + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ +#define CONFIG_MPC512X 1 /* MPC512X family */ + +#define CONFIG_SYS_MPC512X_CLKIN 33333333 /* in Hz */ + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_SYS_IMMR 0x80000000 +#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR+0x2100) + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 + +/* + * DDR Setup - manually set all parameters as there's no SPD etc. + */ +#define CONFIG_SYS_DDR_SIZE 512 /* MB */ + +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is sys memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE + +/* DDR Controller Configuration + * + * SYS_CFG: + * [31:31] MDDRC Soft Reset: Diabled + * [30:30] DRAM CKE pin: Enabled + * [29:29] DRAM CLK: Enabled + * [28:28] Command Mode: Enabled (For initialization only) + * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] + * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] + * [20:19] Read Test: DON'T USE + * [18:18] Self Refresh: Enabled + * [17:17] 16bit Mode: Disabled + * [16:13] Ready Delay: 2 + * [12:12] Half DQS Delay: Disabled + * [11:11] Quarter DQS Delay: Disabled + * [10:08] Write Delay: 2 + * [07:07] Early ODT: Disabled + * [06:06] On DIE Termination: Disabled + * [05:05] FIFO Overflow Clear: DON'T USE here + * [04:04] FIFO Underflow Clear: DON'T USE here + * [03:03] FIFO Overflow Pending: DON'T USE here + * [02:02] FIFO Underlfow Pending: DON'T USE here + * [01:01] FIFO Overlfow Enabled: Enabled + * [00:00] FIFO Underflow Enabled: Enabled + * TIME_CFG0 + * [31:16] DRAM Refresh Time: 0 CSB clocks + * [15:8] DRAM Command Time: 0 CSB clocks + * [07:00] DRAM Precharge Time: 0 CSB clocks + * TIME_CFG1 + * [31:26] DRAM tRFC: + * [25:21] DRAM tWR1: + * [20:17] DRAM tWRT1: + * [16:11] DRAM tDRR: + * [10:05] DRAM tRC: + * [04:00] DRAM tRAS: + * TIME_CFG2 + * [31:28] DRAM tRCD: + * [27:23] DRAM tFAW: + * [22:19] DRAM tRTW1: + * [18:15] DRAM tCCD: + * [14:10] DRAM tRTP: + * [09:05] DRAM tRP: + * [04:00] DRAM tRPA + */ +#ifdef CONFIG_ADS5121_REV2 +#define CONFIG_SYS_MDDRC_SYS_CFG 0xF8604A00 +#define CONFIG_SYS_MDDRC_SYS_CFG_RUN 0xE8604A00 +#define CONFIG_SYS_MDDRC_TIME_CFG1 0x54EC1168 +#define CONFIG_SYS_MDDRC_TIME_CFG2 0x35210864 +#else +#define CONFIG_SYS_MDDRC_SYS_CFG 0xFA804A00 +#define CONFIG_SYS_MDDRC_SYS_CFG_RUN 0xEA804A00 +#define CONFIG_SYS_MDDRC_TIME_CFG1 0x68EC1168 +#define CONFIG_SYS_MDDRC_TIME_CFG2 0x34310864 +#endif +#define CONFIG_SYS_MDDRC_SYS_CFG_EN 0xF0000000 +#define CONFIG_SYS_MDDRC_TIME_CFG0 0x00003D2E +#define CONFIG_SYS_MDDRC_TIME_CFG0_RUN 0x06183D2E + +#define CONFIG_SYS_MICRON_NOP 0x01380000 +#define CONFIG_SYS_MICRON_PCHG_ALL 0x01100400 +#define CONFIG_SYS_MICRON_EM2 0x01020000 +#define CONFIG_SYS_MICRON_EM3 0x01030000 +#define CONFIG_SYS_MICRON_EN_DLL 0x01010000 +#define CONFIG_SYS_MICRON_RFSH 0x01080000 +#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432 +#define CONFIG_SYS_MICRON_OCD_DEFAULT 0x01010780 + +/* DDR Priority Manager Configuration */ +#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777 +#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000 +#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001 +#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC +#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA +#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666 +#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555 +#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444 +#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444 +#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555 +#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558 +#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122 +#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa +#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa +#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666 +#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666 +#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111 + +/* + * NOR FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ + +#define CONFIG_SYS_FLASH_BASE 0xFFC00000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 0x00400000 /* max flash size */ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CONFIG_SYS_FLASH_CHECKSUM + +/* + * NAND FLASH + * drivers/mtd/nand/mpc5121_mpc.c (rev 2 silicon only) + */ +#define CONFIG_CMD_NAND +#define CONFIG_NAND_MPC5121_NFC +#define CONFIG_SYS_NAND_BASE 0x40000000 + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE + +/* + * Configuration parameters for MPC5121 NAND driver + */ +#define CONFIG_FSL_NFC_WIDTH 1 +#define CONFIG_FSL_NFC_WRITE_SIZE 2048 +#define CONFIG_FSL_NFC_SPARE_SIZE 64 +#define CONFIG_FSL_NFC_CHIPS 1 + +#define CONFIG_SYS_SRAM_BASE 0x30000000 +#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */ + +/* ALE active low, data size 4bytes */ +#define CONFIG_SYS_CS0_CFG 0x05051150 + +/* Use not alternative CS timing */ +#define CONFIG_SYS_CS_ALETIMING 0x00000000 + +/* ALE active low, data size 4bytes */ +#define CONFIG_SYS_CS1_CFG 0x1f1f3090 +#define CONFIG_SYS_VPC3_BASE 0x82000000 /* start of VPC3 space */ +#define CONFIG_SYS_VPC3_SIZE 0x00010000 /* max VPC3 size */ + +/* Use SRAM for initial stack */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE /* Init RAM addr */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_SRAM_SIZE + +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Monitor length */ +#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Malloc size */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ +#if CONFIG_PSC_CONSOLE != 3 +#error CONFIG_PSC_CONSOLE must be 3 +#endif +#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE +#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR +#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE +#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ + +/* + * IIM - IC Identification Module + */ +#undef CONFIG_IIM + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ +#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC512x_FEC 1 +#define CONFIG_NET_MULTI +#define CONFIG_PHY_ADDR 0x1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_FEC_AN_TIMEOUT 1 +#define CONFIG_HAS_ETH0 + +/* + * Configure on-board RTC + */ +#define CONFIG_SYS_RTC_BUS_NUM 0x01 +#define CONFIG_SYS_I2C_RTC_ADDR 0x32 +#define CONFIG_RTC_RX8025 + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */ +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */ + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_DATE +#undef CONFIG_CMD_FUSE +#undef CONFIG_CMD_IDE +#undef CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_ELF +#define CONFIG_DOS_PARTITION + +/* + * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock. + * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set + * to 0xFFFF, watchdog timeouts after about 64s. For details refer + * to chapter 36 of the MPC5121e Reference Manual. + */ +/* #define CONFIG_WATCHDOG */ /* enable watchdog */ +#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF + + /* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#ifdef CONFIG_CMD_KGDB +# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 32 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_HZ 1000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory map */ + +/* Cache Configuration */ +#define CONFIG_SYS_DCACHE_SIZE 32768 +#define CONFIG_SYS_CACHELINE_SIZE 32 +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CACHELINE_SHIFT 5 +#endif + +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CONFIG_SYS_HID2 HID2_HBE + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_TIMESTAMP + +#define CONFIG_HOSTNAME mecp512x +#define CONFIG_BOOTFILE /tftpboot/mecp512x/uImage +#define CONFIG_ROOTPATH /tftpboot/mecp512x/target_root + +#define CONFIG_LOADADDR 400000 /* def. location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_PREBOOT "echo;" \ + "echo Welcome to MECP5123" \ + "echo" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "u-boot_addr_r=200000\0" \ + "kernel_addr_r=600000\0" \ + "fdt_addr_r=880000\0" \ + "ramdisk_addr_r=900000\0" \ + "u-boot_addr=FFF00000\0" \ + "kernel_addr=FFC40000\0" \ + "fdt_addr=FFEC0000\0" \ + "ramdisk_addr=FC040000\0" \ + "ramdiskfile=/tftpboot/mecp512x/uRamdisk\0" \ + "u-boot=/tftpboot/mecp512x/u-boot.bin\0" \ + "bootfile=/tftpboot/mecp512x/uImage\0" \ + "fdtfile=/tftpboot/mecp512x/mecp512x.dtb\0" \ + "rootpath=/tftpboot/mecp512x/target_root\n" \ + "netdev=eth0\0" \ + "consdev=ttyPSC0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} " \ + "console=${consdev},${baudrate}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdtfile};" \ + "run nfsargs addip addtty;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "net_self=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${ramdisk_addr_r} ${ramdiskfile};" \ + "tftp ${fdt_addr_r} ${fdtfile};" \ + "run ramargs addip addtty;" \ + "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\ + "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ + "update=protect off ${u-boot_addr} +${filesize};" \ + "era ${u-boot_addr} +${filesize};" \ + "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0" \ + "upd=run load update\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +#define OF_CPU "PowerPC,5121@0" +#define OF_SOC_COMPAT "fsl,mpc5121-immr" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc@80000000/serial@11300" + +#endif /* __CONFIG_H */ |