diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/pr1.h | 157 |
1 files changed, 157 insertions, 0 deletions
diff --git a/include/configs/pr1.h b/include/configs/pr1.h new file mode 100644 index 0000000..03d4269 --- /dev/null +++ b/include/configs/pr1.h @@ -0,0 +1,157 @@ +/* + * U-boot - Configuration file for PR1 Appliance + * + * based on bf537-stamp.h + * Copyright (c) Switchfin Org. <dpn@switchfin.org> + */ + +#ifndef __CONFIG_PR1_H__ +#define __CONFIG_PR1_H__ + +#include <asm/config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf537-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 25000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 24 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 11 +#define CONFIG_MEM_SIZE 128 + +#define CONFIG_EBIU_SDRRC_VAL 0x306 +#define CONFIG_EBIU_SDGCTL_VAL 0x8091998d + +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) + + +/* + * Network Settings + */ +#ifndef __ADSPBF534__ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_BFIN_MAC +#define CONFIG_NETCONSOLE +#endif +#define CONFIG_HOSTNAME pr1 +#define CONFIG_TFTP_BLOCKSIZE 4404 +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ + + +/* + * Flash Settings + */ +#define CONFIG_SYS_NO_FLASH /* We have no parallel FLASH */ + + +/* + * SPI Settings + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO + + +/* + * Env Storage Settings + */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR + + +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C +#define CONFIG_HARD_I2C + + +/* + * NAND Settings + */ +#define CONFIG_NAND_PLAT +#define CONFIG_SYS_NAND_BASE 0x20000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 + +#define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) +#define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) +#define BFIN_NAND_WRITE(addr, cmd) \ + do { \ + bfin_write8(addr, cmd); \ + SSYNC(); \ + } while (0) + +#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) +#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) +#define NAND_PLAT_GPIO_DEV_READY GPIO_PF9 + +/* + * Misc Settings + */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 +#define CONFIG_SYS_PROMPT "pr1>" +#define CONFIG_BOOTCOMMAND "run nandboot" +#define CONFIG_BOOTDELAY 2 +#define CONFIG_LOADADDR 0x2000000 + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +/* + * Overwrite some settings defined in bfin_adi_common.h + */ +#undef NAND_ENV_SETTINGS +#define NAND_ENV_SETTINGS \ + "nandargs=set bootargs " CONFIG_BOOTARGS "\0" \ + "nandboot=" \ + "nand read $(loadaddr) 0x0 0x900000;" \ + "run nandargs;" \ + "bootm" \ + "\0" + +#endif |