diff options
Diffstat (limited to 'include')
25 files changed, 346 insertions, 58 deletions
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index a5736b7..2020e7f 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -398,7 +398,6 @@ /* Network. */ #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC /* NAND support */ diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h index c00d54f..c17327f 100644 --- a/include/configs/am335x_igep0033.h +++ b/include/configs/am335x_igep0033.h @@ -181,7 +181,6 @@ #define CONFIG_NET_RETRY_COUNT 10 #define CONFIG_NET_MULTI #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC /* NAND support */ diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index c773a18..614857d 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -205,4 +205,30 @@ "run usbboot;" #endif + +/* CPSW Ethernet */ +#define CONFIG_CMD_NET +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_DRIVER_TI_CPSW +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB + +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NET_VCI_STRING "AM43xx U-Boot SPL" + +#define CONFIG_SPL_ETH_SUPPORT +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SYS_RX_ETH_BUFFER 64 + #endif /* __CONFIG_AM43XX_EVM_H */ diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index b9aa036..48c12ea 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -103,6 +103,7 @@ #define CONFIG_CMD_PING 1 #define CONFIG_CMD_DHCP 1 #define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_MMC #define CONFIG_CMD_USB 1 /* SDRAM */ @@ -123,6 +124,18 @@ #define DATAFLASH_TCSS (0x1a << 16) #define DATAFLASH_TCHS (0x1 << 24) +/* MMC */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#endif + +/* FAT */ +#ifdef CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + /* NOR flash, if populated */ #ifdef CONFIG_SYS_USE_NORFLASH #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h index 1f57bd2..7bbe596 100644 --- a/include/configs/bur_am335x_common.h +++ b/include/configs/bur_am335x_common.h @@ -51,7 +51,6 @@ #define CONFIG_MII /* Required in net/eth.c */ #define CONFIG_SPL_ETH_SUPPORT #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_NATSEMI #define CONFIG_SPL_NET_SUPPORT #define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h index 56e9a8e..26b615b 100644 --- a/include/configs/cm_t335.h +++ b/include/configs/cm_t335.h @@ -114,7 +114,6 @@ /* Network. */ #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_ATHEROS /* NAND support */ diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index c67cf60..291c538 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -62,7 +62,6 @@ #define CONFIG_MII /* Required in net/eth.c */ #define CONFIG_PHY_GIGE /* per-board part of CPSW */ #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 2 /* SPI */ #undef CONFIG_OMAP3_SPI diff --git a/include/configs/dxr2.h b/include/configs/dxr2.h index 1e42f5c..75f7812 100644 --- a/include/configs/dxr2.h +++ b/include/configs/dxr2.h @@ -26,6 +26,7 @@ #define BOARD_DFU_BUTTON_GPIO 27 #define BOARD_DFU_BUTTON_LED 64 +#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ #undef CONFIG_DOS_PARTITION #undef CONFIG_CMD_FAT @@ -49,7 +50,6 @@ #undef CONFIG_MII #undef CONFIG_PHY_GIGE -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC #define CONFIG_FACTORYSET diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index 12d8141..d56d5b0 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -37,6 +37,11 @@ #define CONFIG_SHOW_BOOT_PROGRESS #endif +/* GPIO banks */ +#define CONFIG_OMAP3_GPIO_3 /* GPIO64 .. 95 is in GPIO bank 3 */ +#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ +#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ + /* USB */ #define CONFIG_MUSB_UDC 1 #define CONFIG_USB_OMAP3 1 diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 6f41ee7..9af3efd 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -297,7 +297,6 @@ #define CONFIG_NET_MULTI #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC #endif /* ! __CONFIG_PCM051_H */ diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h index 5a55556..fc25966 100644 --- a/include/configs/pengwyn.h +++ b/include/configs/pengwyn.h @@ -196,7 +196,6 @@ /* Network */ #define CONFIG_CMD_MII #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_RESET 1 #define CONFIG_PHY_NATSEMI diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index 7722f7b..6276d43 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -44,7 +44,6 @@ #undef CONFIG_SPL_NET_VCI_STRING #undef CONFIG_SPL_ETH_SUPPORT -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_ATHEROS #define CONFIG_FACTORYSET diff --git a/include/configs/rut.h b/include/configs/rut.h index d4519f9..6bddede 100644 --- a/include/configs/rut.h +++ b/include/configs/rut.h @@ -41,7 +41,6 @@ #undef CONFIG_SPL_NET_VCI_STRING #undef CONFIG_SPL_ETH_SUPPORT -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_NATSEMI #define CONFIG_FACTORYSET diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h new file mode 100644 index 0000000..91cc7d8 --- /dev/null +++ b/include/configs/sama5d3_xplained.h @@ -0,0 +1,203 @@ +/* + * Configuration settings for the SAMA5D3 Xplained board. + * + * Copyright (C) 2014 Atmel Corporation + * Bo Shen <voice.shen@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/hardware.h> + +#define CONFIG_SYS_TEXT_BASE 0x26f00000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_AT91FAMILY +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT /* Device Tree support */ + +/* general purpose I/O */ +#define CONFIG_AT91_GPIO + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_DBGU + +/* + * This needs to be defined for the OHCI code to work but it is defined as + * ATMEL_ID_UHPHS in the CPU specific header files. + */ +#define ATMEL_ID_UHP ATMEL_ID_UHPHS + +/* + * Specify the clock enable bit in the PMC_SCER register. + */ +#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_LOADS +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS +#define CONFIG_SYS_SDRAM_SIZE 0x10000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) + +/* NAND flash */ +#define CONFIG_CMD_NAND + +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ONFI_DETECTION +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC +#define CONFIG_ATMEL_NAND_HW_PMECC +#define CONFIG_PMECC_CAP 4 +#define CONFIG_PMECC_SECTOR_SIZE 512 +#define CONFIG_CMD_NAND_TRIMFFS +#define CONFIG_CMD_MTDPARTS + +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_RBTREE +#define CONFIG_LZO +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#endif + +/* Ethernet Hardware */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY +#define CONFIG_RGMII +#define CONFIG_CMD_MII +#define CONFIG_PHYLIB + +/* MMC */ +#define CONFIG_CMD_MMC + +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#define CONFIG_ATMEL_MCI_8BIT +#endif + +/* USB */ +#define CONFIG_CMD_USB + +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_ATMEL +#define CONFIG_USB_ATMEL_CLK_SEL_UPLL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_DOS_PARTITION +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE +#endif + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + +#if CONFIG_SYS_USE_NANDFLASH +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0xc0000 +#define CONFIG_ENV_OFFSET_REDUND 0x100000 +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ + "nand read 0x22000000 0x200000 0x600000;" \ + "bootz 0x22000000 - 0x21000000" +#elif CONFIG_SYS_USE_MMC +/* bootstrap + u-boot + env in sd card */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d3_xplained.dtb; " \ + "fatload mmc 0:1 0x22000000 zImage; " \ + "bootz 0x22000000 - 0x21000000" +#define CONFIG_SYS_MMC_ENV_DEV 0 +#else +#define CONFIG_ENV_IS_NOWHERE +#endif + +#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "root=/dev/mmcblk0p2 rw rootwait" +#else +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ + "256K(env),256k(evn_redundent),256k(spare)," \ + "512k(dtb),6M(kernel)ro,-(rootfs) " \ + "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs" +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +#endif diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h index c34feb5..516be85 100644 --- a/include/configs/sama5d3xek.h +++ b/include/configs/sama5d3xek.h @@ -258,6 +258,8 @@ #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_BOARD_INIT +#define CONFIG_SYS_MONITOR_LEN (512 << 10) + #ifdef CONFIG_SYS_USE_MMC #define CONFIG_SPL_LDSCRIPT arch/arm/cpu/at91-common/u-boot-spl.lds #define CONFIG_SPL_MMC_SUPPORT @@ -267,6 +269,27 @@ #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_LIBDISK_SUPPORT + +#elif CONFIG_SYS_USE_NANDFLASH +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_SIZE 0x800 +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 + +#elif CONFIG_SYS_USE_SERIALFLASH +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400 + #endif #endif diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index e1a3bbc..76dad4e 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -66,27 +66,63 @@ #define BOOT_TARGETS_DHCP "" #endif +#if defined(CONFIG_CMD_DHCP) && defined(CONFIG_CMD_PXE) +#define BOOTCMDS_PXE \ + "bootcmd_pxe=" \ + BOOTCMD_INIT_USB \ + "dhcp; " \ + "if pxe get; then " \ + "pxe boot; " \ + "fi\0" +#define BOOT_TARGETS_PXE "pxe" +#else +#define BOOTCMDS_PXE "" +#define BOOT_TARGETS_PXE "" +#endif + #define BOOTCMDS_COMMON \ "rootpart=1\0" \ \ + "do_script_boot=" \ + "load ${devtype} ${devnum}:${rootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "source ${scriptaddr}\0" \ + \ "script_boot=" \ - "if load ${devtype} ${devnum}:${rootpart} " \ - "${scriptaddr} ${prefix}${script}; then " \ - "echo ${script} found! Executing ...;" \ - "source ${scriptaddr};" \ - "fi;\0" \ + "for script in ${boot_scripts}; do " \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}${script}; then " \ + "echo Found U-Boot script " \ + "${prefix}${script}; " \ + "run do_script_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi; " \ + "done\0" \ + \ + "do_sysboot_boot=" \ + "sysboot ${devtype} ${devnum}:${rootpart} any " \ + "${scriptaddr} ${prefix}extlinux.conf\0" \ + \ + "sysboot_boot=" \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}extlinux.conf; then " \ + "echo Found extlinux config " \ + "${prefix}extlinux.conf; " \ + "run do_sysboot_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi\0" \ \ "scan_boot=" \ "echo Scanning ${devtype} ${devnum}...; " \ "for prefix in ${boot_prefixes}; do " \ - "for script in ${boot_scripts}; do " \ - "run script_boot; " \ - "done; " \ - "done;\0" \ + "run sysboot_boot; " \ + "run script_boot; " \ + "done\0" \ \ "boot_targets=" \ BOOT_TARGETS_MMC " " \ BOOT_TARGETS_USB " " \ + BOOT_TARGETS_PXE " " \ BOOT_TARGETS_DHCP " " \ "\0" \ \ @@ -96,7 +132,8 @@ \ BOOTCMDS_MMC \ BOOTCMDS_USB \ - BOOTCMDS_DHCP + BOOTCMDS_DHCP \ + BOOTCMDS_PXE #define CONFIG_BOOTCOMMAND \ "set usb_need_init; " \ diff --git a/include/configs/tegra-common.h b/include/configs/tegra-common.h index 9247aef..ae786cf 100644 --- a/include/configs/tegra-common.h +++ b/include/configs/tegra-common.h @@ -29,7 +29,6 @@ #define CONFIG_DISPLAY_BOARDINFO #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_OF_LIBFDT /* enable passing of devicetree */ /* Environment */ #define CONFIG_ENV_VARS_UBOOT_CONFIG @@ -69,33 +68,20 @@ #undef CONFIG_CMD_NET /* network support */ /* turn on command-line edit/hist/auto */ -#define CONFIG_CMDLINE_EDITING #define CONFIG_COMMAND_HISTORY -#define CONFIG_AUTO_COMPLETE /* turn on commonly used storage-related commands */ - -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION #define CONFIG_PARTITION_UUIDS -#define CONFIG_FS_EXT4 -#define CONFIG_FS_FAT -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_FS_GENERIC #define CONFIG_CMD_PART #define CONFIG_SYS_NO_FLASH #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_BOOTDELAY 2 /* -1 to disable auto boot */ /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT V_PROMPT /* * Increasing the size of the IO buffer as default nfsargs size is more @@ -133,8 +119,6 @@ #define CONFIG_TEGRA_GPIO #define CONFIG_CMD_GPIO #define CONFIG_CMD_ENTERRCM -#define CONFIG_CMD_BOOTZ -#define CONFIG_SUPPORT_RAW_INITRD /* Defines for SPL */ #define CONFIG_SPL @@ -161,4 +145,8 @@ #define CONFIG_BOUNCE_BUFFER #define CONFIG_CRC32_VERIFY +#ifndef CONFIG_SPL_BUILD +#include <config_distro_defaults.h> +#endif + #endif /* _TEGRA_COMMON_H_ */ diff --git a/include/configs/tegra114-common.h b/include/configs/tegra114-common.h index a4e8a5f..555c237 100644 --- a/include/configs/tegra114-common.h +++ b/include/configs/tegra114-common.h @@ -26,11 +26,6 @@ */ #define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA114 /* in a NVidia Tegra114 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ @@ -51,6 +46,9 @@ * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it above BOOTMAPSZ to eliminate conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -68,6 +66,7 @@ */ #define MEM_LAYOUT_ENV_SETTINGS \ "scriptaddr=0x90000000\0" \ + "pxefile_addr_r=0x90100000\0" \ "kernel_addr_r=0x81000000\0" \ "fdt_addr_r=0x82000000\0" \ "ramdisk_addr_r=0x82100000\0" @@ -83,5 +82,6 @@ /* For USB EHCI controller */ #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #endif /* _TEGRA114_COMMON_H_ */ diff --git a/include/configs/tegra124-common.h b/include/configs/tegra124-common.h index 0a4541b..61e5026 100644 --- a/include/configs/tegra124-common.h +++ b/include/configs/tegra124-common.h @@ -18,11 +18,6 @@ */ #define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA124 /* is an NVIDIA Tegra124 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ @@ -79,5 +74,6 @@ /* For USB EHCI controller */ #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #endif /* _TEGRA124_COMMON_H_ */ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index b009a31..21bf977 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -24,11 +24,6 @@ */ #define V_NS16550_CLK 216000000 /* 216MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA20 /* in a NVidia Tegra20 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x00408000 /* def. location for kernel */ @@ -49,6 +44,9 @@ * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it above BOOTMAPSZ to eliminate conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -66,6 +64,7 @@ */ #define MEM_LAYOUT_ENV_SETTINGS \ "scriptaddr=0x10000000\0" \ + "pxefile_addr_r=0x10100000\0" \ "kernel_addr_r=0x01000000\0" \ "fdt_addr_r=0x02000000\0" \ "ramdisk_addr_r=0x02100000\0" @@ -96,6 +95,7 @@ */ #define CONFIG_USB_EHCI_TXFIFO_THRESH 10 #define CONFIG_EHCI_IS_TDI +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 /* Total I2C ports on Tegra20 */ #define TEGRA_I2C_NUM_CONTROLLERS 4 diff --git a/include/configs/tegra30-common.h b/include/configs/tegra30-common.h index b5550d7..443c842 100644 --- a/include/configs/tegra30-common.h +++ b/include/configs/tegra30-common.h @@ -23,11 +23,6 @@ */ #define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA30 /* in a NVidia Tegra30 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ @@ -48,6 +43,9 @@ * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it above BOOTMAPSZ to eliminate conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -65,6 +63,7 @@ */ #define MEM_LAYOUT_ENV_SETTINGS \ "scriptaddr=0x90000000\0" \ + "pxefile_addr_r=0x90100000\0" \ "kernel_addr_r=0x81000000\0" \ "fdt_addr_r=0x82000000\0" \ "ramdisk_addr_r=0x82100000\0" @@ -80,5 +79,6 @@ /* For USB EHCI controller */ #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #endif /* _TEGRA30_COMMON_H_ */ diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index ba16b1c..b51400c 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -233,7 +233,6 @@ #define CONFIG_NET_MULTI #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_ET1011C #define CONFIG_PHY_ET1011C_TX_CLK_FIX diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 7e9ca01..50c3203 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -30,6 +30,7 @@ /* Network defines. */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ #define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII #define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ #define CONFIG_BOOTP_DNS2 #define CONFIG_BOOTP_SEND_HOSTNAME diff --git a/include/cpsw.h b/include/cpsw.h index 743cb96..a73843d 100644 --- a/include/cpsw.h +++ b/include/cpsw.h @@ -19,7 +19,7 @@ struct cpsw_slave_data { u32 slave_reg_ofs; u32 sliver_reg_ofs; - int phy_id; + int phy_addr; int phy_if; }; diff --git a/include/nand.h b/include/nand.h index 84116f4..fc735d1 100644 --- a/include/nand.h +++ b/include/nand.h @@ -21,10 +21,16 @@ * at the same time, so do it here. When all drivers are * converted, this will go away. */ +#ifdef CONFIG_SPL_BUILD +#if defined(CONFIG_NAND_FSL_ELBC) || defined(CONFIG_NAND_FSL_IFC) +#define CONFIG_SYS_NAND_SELF_INIT +#endif +#else #if defined(CONFIG_NAND_FSL_ELBC) || defined(CONFIG_NAND_ATMEL)\ || defined(CONFIG_NAND_FSL_IFC) #define CONFIG_SYS_NAND_SELF_INIT #endif +#endif extern void nand_init(void); |