diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/cm_t54.h | 149 | ||||
| -rw-r--r-- | include/configs/duovero.h | 62 | ||||
| -rw-r--r-- | include/configs/omap3_overo.h | 296 | ||||
| -rw-r--r-- | include/configs/siemens-am33x-common.h | 2 | ||||
| -rw-r--r-- | include/configs/ti_omap4_common.h | 9 |
5 files changed, 317 insertions, 201 deletions
diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h new file mode 100644 index 0000000..db04095 --- /dev/null +++ b/include/configs/cm_t54.h @@ -0,0 +1,149 @@ +/* + * Config file for Compulab CM-T54 board + * + * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/ + * + * Author: Dmitry Lifshitz <lifshitz@compulab.co.il> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_CM_T54_H +#define __CONFIG_CM_T54_H + +#define CONFIG_CM_T54 +#define CONFIG_DRAM_2G + +#include <configs/ti_omap5_common.h> + +#undef CONFIG_MISC_INIT_R +#undef CONFIG_SPL_OS_BOOT + +/* Device Tree defines */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/* EEPROM related defines */ +#define CONFIG_SYS_I2C_OMAP34XX +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* Enable SD/MMC CD and WP GPIOs */ +#define OMAP_HSMMC_USE_GPIO + +/* UART setup */ +#define CONFIG_CONS_INDEX 4 +#define CONFIG_SYS_NS16550_COM4 UART4_BASE +#define CONFIG_BAUDRATE 115200 + +/* SD/MMC RAW boot */ +#undef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR +#undef CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 /* 0x40000 - 256 KB */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 /* 384 KB */ + +/* MMC ENV related defines */ +#undef CONFIG_ENV_OFFSET +#undef CONFIG_ENV_SIZE + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */ +#define CONFIG_SYS_MMC_ENV_PART 0 +#define CONFIG_ENV_OFFSET 0xc0000 /* (in bytes) 768 KB */ +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_CMD_SAVEENV + +/* Enhance our eMMC support / experience. */ +#define CONFIG_HSMMC2_8BIT +#define CONFIG_SUPPORT_EMMC_BOOT + +/* USB UHH support options */ +#define CONFIG_CMD_USB +#define CONFIG_USB_HOST +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_OMAP +#define CONFIG_USB_STORAGE +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET + +#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 76 /* HSIC2 HUB #RESET */ +#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 83 /* HSIC3 ETH #RESET */ + +/* Enabled commands */ +#define CONFIG_CMD_DHCP /* DHCP Support */ +#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#define CONFIG_CMD_PING + +/* USB Networking options */ +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_SMSC95XX +#define CONFIG_USB_ETHER_RNDIS +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_MCS7830 + +/* Max time to hold reset on this board, see doc/README.omap-reset-time */ +#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 + +/* + * Miscellaneous configurable options + */ +#undef CONFIG_SYS_AUTOLOAD +#undef CONFIG_SYS_PROMPT +#undef CONFIG_EXTRA_ENV_SETTINGS +#undef CONFIG_BOOTCOMMAND +#undef CONFIG_BOOTDELAY + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_SYS_AUTOLOAD "no" +#define CONFIG_SYS_PROMPT "CM-T54 # " + +#define CONFIG_EXTRA_ENV_SETTINGS \ + DEFAULT_LINUX_BOOT_ENV \ + "baudrate=115200\0" \ + "bootdelay=3\0" \ + "autoload=no\0" \ + "bootscr=bootscr.img\0" \ + "fdtfile=omap5-sbc-t54.dtb\0" \ + "kernel=zImage-cm-t54\0" \ + "ramdisk=ramdisk-cm-t54.img\0" \ + "console=ttyO3\0" \ + "ramdisksize=16384\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk1p2\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "root=${mmcroot} rw rootwait\0" \ + "ramroot=/dev/ram0\0" \ + "ramargs=setenv bootargs console=${console} " \ + "root=${ramroot} ramdisk_size=${ramdisksize} rw\0" \ + "mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \ + "mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \ + "mmcloadramdisk=load mmc ${mmcdev} ${rdaddr} ${ramdisk}\0" \ + "mmcloadbootscript=load mmc ${mmcdev} ${loadaddr} ${bootsrc}\0" \ + "mmcbootscript=echo Running bootscript from mmc${mmcdev}...; " \ + "source ${loadaddr}\0" \ + "mmcbootlinux=echo Booting from mmc${mmcdev} ...; " \ + "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \ + "mmcboot=if mmc dev ${mmcdev} && mmc rescan; then " \ + "if run mmcloadbootscript; " \ + "then run mmcbootscript; " \ + "fi; " \ + "if run mmcloadkernel; then " \ + "if run mmcloadfdt; then " \ + "if run mmcloadramdisk; then " \ + "run ramargs; " \ + "run mmcbootlinux; " \ + "fi; " \ + "run mmcargs; " \ + "setenv rdaddr - ; " \ + "run mmcbootlinux; " \ + "fi; " \ + "fi; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "bootcmd=run mmcboot || setenv mmcdev 1; setenv mmcroot /dev/mmcblk0p2; run mmcboot;" + +#endif /* __CONFIG_CM_T54_H */ diff --git a/include/configs/duovero.h b/include/configs/duovero.h new file mode 100644 index 0000000..e68f415 --- /dev/null +++ b/include/configs/duovero.h @@ -0,0 +1,62 @@ +/* + * (C) Copyright: 2013 + * Gumstix, Inc - http://www.gumstix.com + * Maintainer: Ash Charles <ash@gumstix.com> + * + * Configuration settings for the Gumstix DuoVero board. + * See omap4_common.h for OMAP4 common part + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_DUOVERO_H +#define __CONFIG_DUOVERO_H + +/* + * High Level Configuration Options + */ +#define CONFIG_DUOVERO +#define MACH_TYPE_OMAP4_DUOVERO 4097 /* Until the next sync */ +#define CONFIG_MACH_TYPE MACH_TYPE_OMAP4_DUOVERO + +#include <configs/ti_omap4_common.h> + +#undef CONFIG_SPL_OS_BOOT + +#undef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS +#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION +#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS + +#undef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "duovero # " + +/* USB UHH support options */ +#define CONFIG_CMD_USB +#define CONFIG_USB_HOST +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_OMAP +#define CONFIG_USB_STORAGE +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 + +#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 1 +#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 62 + +#define CONFIG_SYS_ENABLE_PADS_ALL + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NET + +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE 0x2C000000 + +/* GPIO */ +#define CONFIG_CMD_GPIO + +/* ENV related config options */ +#define CONFIG_ENV_IS_NOWHERE + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +#endif /* __CONFIG_DUOVERO_H */ diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index 007e27f..7b97be9 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -7,135 +7,88 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* - * High Level Configuration Options - */ -#define CONFIG_OMAP /* in a TI OMAP core */ -#define CONFIG_OMAP34XX /* which is a 34XX */ -#define CONFIG_OMAP3_OVERO /* working with overo */ -#define CONFIG_OMAP_GPIO -#define CONFIG_OMAP_COMMON - -#define CONFIG_SDRC /* The chip has SDRC controller */ +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ +#define CONFIG_NAND -#include <asm/arch/cpu.h> /* get chip and board defs */ -#include <asm/arch/omap3.h> +#include <configs/ti_omap3_common.h> -/* - * Display CPU and Board information - */ +/* Display CPU and Board information */ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - +/* call misc_init_r */ #define CONFIG_MISC_INIT_R -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG +/* pass the revision tag */ #define CONFIG_REVISION_TAG -#define CONFIG_OF_LIBFDT +/* override size of malloc() pool */ +#undef CONFIG_SYS_MALLOC_LEN +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ +/* Shift 128 << 15 provides 4 MiB heap to support UBI commands. + * Shift 128 << 10 provides 128 KiB heap for limited-memory devices. */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 15)) -/* - * Size of malloc() pool - */ -#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ - /* Sector */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) - -/* - * Hardware drivers - */ - -/* - * NS16550 Configuration - */ -#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK +/* I2C Support */ +#define CONFIG_SYS_I2C_OMAP34XX -/* - * select serial console configuration - */ -#define CONFIG_CONS_INDEX 3 -#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 -#define CONFIG_SERIAL3 3 +/* TWL4030 LED */ +#define CONFIG_TWL4030_LED -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \ - 115200} -#define CONFIG_GENERIC_MMC -#define CONFIG_MMC -#define CONFIG_OMAP_HSMMC -#define CONFIG_DOS_PARTITION +/* Initialize GPIOs by default */ +#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 is in GPIO Bank 2 */ +#define CONFIG_OMAP3_GPIO_3 /* GPIO64..95 is in GPIO Bank 3 */ +#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */ +#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO Bank 5 */ +#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */ /* commands to include */ -#include <config_cmd_default.h> - #define CONFIG_CMD_CACHE -#define CONFIG_CMD_EXT2 /* EXT2 Support */ -#define CONFIG_CMD_FAT /* FAT support */ -#define CONFIG_CMD_JFFS2 /* JFFS2 Support */ - -#define CONFIG_CMD_I2C /* I2C serial bus support */ -#define CONFIG_CMD_MMC /* MMC support */ -#define CONFIG_CMD_NAND /* NAND support */ - -#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ #undef CONFIG_CMD_IMI /* iminfo */ -#undef CONFIG_CMD_IMLS /* List all found images */ #undef CONFIG_CMD_NFS /* NFS support */ -#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ -#define CONFIG_SYS_NO_FLASH -#define CONFIG_SYS_I2C -#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 -#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 -#define CONFIG_SYS_I2C_OMAP34XX +#ifdef CONFIG_NAND +#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */ +#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */ -/* - * TWL4030 - */ -#define CONFIG_TWL4030_POWER -#define CONFIG_TWL4030_LED +#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */ +#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */ -/* - * Board NAND Info. +#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */ + +/* NAND block size is 128 KiB. Synchronize these values with + * overo_nand_partitions in mach-omap2/board-overo.c in Linux: + * xloader 4 * NAND_BLOCK_SIZE = 512 KiB + * uboot 14 * NAND_BLOCK_SIZE = 1792 KiB + * uboot environtment 2 * NAND_BLOCK_SIZE = 256 KiB + * linux 64 * NAND_BLOCK_SIZE = 8 MiB + * rootfs remainder */ +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \ + "512k(xloader)," \ + "1792k(u-boot)," \ + "256k(environ)," \ + "8m(linux)," \ + "-(rootfs)" +#else /* CONFIG_NAND */ +#define MTDPARTS_DEFAULT +#endif /* CONFIG_NAND */ + +/* Board NAND Info. */ #define CONFIG_SYS_NAND_QUIET_TEST -#define CONFIG_NAND_OMAP_GPMC #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ /* to access nand */ -#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ - /* to access nand */ - /* at CS0 */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ - /* devices */ -#define CONFIG_JFFS2_NAND -/* nand device jffs2 lives on */ -#define CONFIG_JFFS2_DEV "nand0" -/* start of jffs2 partition */ -#define CONFIG_JFFS2_PART_OFFSET 0x680000 -#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */ - /* partition */ - /* Environment information */ -#define CONFIG_BOOTDELAY 5 - #define CONFIG_EXTRA_ENV_SETTINGS \ - "loadaddr=0x82000000\0" \ + DEFAULT_LINUX_BOOT_ENV \ + "fdtfile=overo.dtb\0" \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "usbtty=cdc_acm\0" \ "console=ttyO2,115200n8\0" \ - "mpurate=500\0" \ + "mpurate=auto\0" \ "optargs=\0" \ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ @@ -145,6 +98,7 @@ "mmcrootfstype=ext3 rootwait\0" \ "nandroot=ubi0:rootfs ubi.mtd=4\0" \ "nandrootfstype=ubifs\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ "mmcargs=setenv bootargs console=${console} " \ "${optargs} " \ "mpurate=${mpurate} " \ @@ -161,80 +115,69 @@ "omapdss.def_disp=${defaultdisplay} " \ "root=${nandroot} " \ "rootfstype=${nandrootfstype}\0" \ - "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ + "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \ + "bootscript=echo Running boot script from mmc ...; " \ "source ${loadaddr}\0" \ - "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ - "mmcboot=echo Booting from mmc ...; " \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t ${loadaddr} ${filesize}\0" \ + "loaduimage=load mmc ${mmcdev} ${loadaddr} uImage\0" \ + "mmcboot=echo Booting from mmc...; " \ "run mmcargs; " \ "bootm ${loadaddr}\0" \ + "loadzimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}\0" \ + "loadfdt=load mmc ${mmcdev}:2 ${fdtaddr} ${bootdir}/${fdtfile}\0" \ + "mmcbootfdt=echo Booting with DT from mmc ...; " \ + "run mmcargs; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ "nandboot=echo Booting from nand ...; " \ "run nandargs; " \ - "nand read ${loadaddr} 280000 400000; " \ + "nand read ${loadaddr} linux; " \ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev}; if mmc rescan; then " \ "if run loadbootscript; then " \ "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run nandboot; " \ - "fi; " \ - "fi; " \ - "else run nandboot; fi" + "fi;" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loaduimage; then " \ + "run mmcboot;" \ + "fi;" \ + "if run loadzimage; then " \ + "if test -n $fdtfile; then " \ + "if run loadfdt; then " \ + "run mmcbootfdt;" \ + "fi;" \ + "fi;" \ + "fi;" \ + "fi;" \ + "run nandboot; " \ -#define CONFIG_AUTO_COMPLETE 1 /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#undef CONFIG_SYS_PROMPT #define CONFIG_SYS_PROMPT "Overo # " -#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command */ - /* args */ -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* memtest works on */ #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 0x01F00000) /* 31MB */ -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ - /* address */ -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -/* **** PISMO SUPPORT *** */ - +/* FLASH and environment organization */ /* Configure the PISMO */ #define PISMO1_NAND_SIZE GPMC_SIZE_128M #define PISMO1_ONEN_SIZE GPMC_SIZE_128M -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - -#if defined(CONFIG_CMD_NAND) +#if defined(CONFIG_NAND) #define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE #endif @@ -250,67 +193,18 @@ #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET +/* Configure SMSC9211 ethernet */ #if defined(CONFIG_CMD_NET) -/*---------------------------------------------------------------------------- - * SMSC9211 Ethernet from SMSC9118 family - *---------------------------------------------------------------------------- - */ - #define CONFIG_SMC911X #define CONFIG_SMC911X_32_BIT #define CONFIG_SMC911X_BASE 0x2C000000 - #endif /* (CONFIG_CMD_NET) */ -/* - * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader - * and older u-boot.bin with the new U-Boot SPL. - */ -#define CONFIG_SYS_TEXT_BASE 0x80008000 -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +/* Initial RAM setup */ #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - #define CONFIG_SYS_CACHELINE_SIZE 64 -/* Defines for SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_TEXT_BASE 0x40200800 -#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ -#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK - -/* move malloc and bss high to prevent clashing with the main image */ -#define CONFIG_SYS_SPL_MALLOC_START 0x87000000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 -#define CONFIG_SPL_BSS_START_ADDR 0x87080000 /* end of minimum RAM */ -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ - -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ -#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ -#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 -#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" - -#define CONFIG_SPL_BOARD_INIT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBDISK_SUPPORT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_MMC_SUPPORT -#define CONFIG_SPL_FAT_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SPL_GPIO_SUPPORT -#define CONFIG_SPL_POWER_SUPPORT -#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" - /* NAND boot config */ #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_COUNT 64 diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 73a123d..53816a6 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -46,6 +46,8 @@ #define CONFIG_CMD_ECHO #define CONFIG_CMD_CACHE +#define CONFIG_SYS_GENERIC_BOARD + #define CONFIG_ENV_VARS_UBOOT_CONFIG #ifndef CONFIG_SPL_BUILD #define CONFIG_ROOTPATH "/opt/eldk" diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h index 77fbfb6..44b3718 100644 --- a/include/configs/ti_omap4_common.h +++ b/include/configs/ti_omap4_common.h @@ -109,9 +109,13 @@ "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \ "env import -t ${loadaddr} ${filesize}\0" \ "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ + "loaduimage=load mmc ${mmcdev} ${loadaddr} uImage\0" \ "mmcboot=echo Booting from mmc${mmcdev} ...; " \ "run mmcargs; " \ "bootz ${loadaddr} - ${fdtaddr}\0" \ + "uimageboot=echo Booting from mmc${mmcdev} ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr}\0" \ "findfdt="\ "if test $board_name = sdp4430; then " \ "setenv fdtfile omap4-sdp.dtb; fi; " \ @@ -121,6 +125,8 @@ "setenv fdtfile omap4-panda-a4.dtb; fi;" \ "if test $board_name = panda-es; then " \ "setenv fdtfile omap4-panda-es.dtb; fi;" \ + "if test $board_name = duovero; then " \ + "setenv fdtfile omap4-duovero.dtb; fi;" \ "if test $fdtfile = undefined; then " \ "echo WARNING: Could not determine device tree to use; fi; \0" \ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ @@ -144,6 +150,9 @@ "run loadfdt;" \ "run mmcboot; " \ "fi; " \ + "if run loaduimage; then " \ + "run uimageboot;" \ + "fi; " \ "fi" /* |