diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/MPC8641HPCN.h | 203 | ||||
| -rw-r--r-- | include/mpc86xx.h | 6 |
2 files changed, 87 insertions, 122 deletions
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 8d2e088..76efd7c 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -1,5 +1,6 @@ -/* - * Copyright 2004 Freescale Semiconductor. +/* + * Copyright 2006 Freescale Semiconductor. + * * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) * * See file CREDITS for list of people who contributed to this @@ -22,8 +23,7 @@ */ /* - * mpc8641hpc3 board configuration file - * + * MPC8641HPCN board configuration file * * Make sure you change the MAC address and other network params first, * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. @@ -38,48 +38,38 @@ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ -#undef DEBUG +#undef DEBUG -//#define RUN_DIAG 1 #ifdef RUN_DIAG #define CFG_DIAG_ADDR 0xff800000 #endif + #define CFG_RESET_ADDRESS 0xfff00100 -//#define CONFIG_PCI +#undef CONFIG_PCI + #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -/*#define CONFIG_DDR_ECC */ /* only for ECC DDR module */ -/*#define CONFIG_DDR_DLL */ /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ - +#undef CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ #define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef +#define CONFIG_ALTIVEC 1 -#define CONFIG_ALTIVEC 1 -/*----------------------------------------------------------------------- +/* * L2CR setup -- make sure this is right for your board! */ - -#define CFG_L2 +#define CFG_L2 #define L2_INIT 0 #define L2_ENABLE (L2CR_L2E) #ifndef CONFIG_SYS_CLK_FREQ -//#define CONFIG_SYS_CLK_FREQ 33000000 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) #endif -/* - * These can be toggled for performance analysis, otherwise use default. - */ -/* JB - XXX - Are these available on 86xx? */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ - #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #undef CFG_DRAM_TEST /* memory test, takes time */ @@ -130,10 +120,10 @@ #define CFG_DDR_INTERVAL 0x06090100 #define CFG_DDR_DATA_INIT 0xdeadbeef #define CFG_DDR_CLK_CTRL 0x03800000 - #define CFG_DDR_OCD_CTRL 0x00000000 - #define CFG_DDR_OCD_STATUS 0x00000000 + #define CFG_DDR_OCD_CTRL 0x00000000 + #define CFG_DDR_OCD_STATUS 0x00000000 #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ - #define CFG_DDR_CONTROL2 0x04400000 + #define CFG_DDR_CONTROL2 0x04400000 //Not used in fixed_sdram function @@ -143,20 +133,12 @@ #define CFG_DDR_CS3_BNDS 0x00000FFF //Not done #define CFG_DDR_CS4_BNDS 0x00000FFF //Not done #define CFG_DDR_CS5_BNDS 0x00000FFF //Not done - - - #endif #endif /* - * SDRAM on the Local Bus - */ -//#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -//#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* In MPC8641HPCN, we allocate 16MB flash spaces at fe000000 and ff000000 + * In MPC8641HPCN, we allocate 16MB flash spaces at fe000000 and ff000000 * We only have an 8MB flash. In effect, the addresses from fe000000 to fe7fffff * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff. * However, when u-boot comes up, the flash_init needs hard start addresses @@ -165,15 +147,12 @@ * knows where the flash is and the user can download u-boot code from promjet to * fef00000 <- more intuitive than fe700000. Note that, on switching the boot * location, fef00000 becomes fff00000. -*/ + */ #define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */ -#define CFG_FLASH_BASE2 0xff800000 +#define CFG_FLASH_BASE2 0xff800000 #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} - -/*Sri: This looks like a good place to init all the Local Bus chip selects*/ - #define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */ #define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/ @@ -186,25 +165,24 @@ #define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */ #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ -#define PIXIS_BASE 0xf8100000 /* PIXIS registers*/ -#define PIXIS_ID 0x0 /* MPC8641HPCN Board ID at offset 0*/ -#define PIXIS_VER 0x1 /* MPC8641HPCN board version version at offset 1*/ -#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2*/ -#define PIXIS_RST 0x4 /* PIXIS Reset Control register*/ -#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ -#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ -#define PIXIS_VCTL 0x10 /* VELA Control Register */ -#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ -#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ -#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ -#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ -#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ -#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ -#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ +#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ +#define PIXIS_ID 0x0 /* Board ID at offset 0 */ +#define PIXIS_VER 0x1 /* Board version at offset 1 */ +#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ +#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ +#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ +#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ +#define PIXIS_VCTL 0x10 /* VELA Control Register */ +#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ +#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ +#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ +#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ +#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ +#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ +#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -//#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ #define CFG_MAX_FLASH_SECT 128 /* sectors per device */ #undef CFG_FLASH_CHECKSUM @@ -212,11 +190,9 @@ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ -/*#define CFG_HPCN_FLASH_CFI_DRIVER */ #define CFG_FLASH_CFI #define CFG_FLASH_EMPTY_INFO - #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else @@ -230,7 +206,7 @@ #undef CONFIG_CLOCKS_IN_MHZ #define CONFIG_L1_INIT_RAM -#undef CFG_INIT_RAM_LOCK +#undef CFG_INIT_RAM_LOCK #ifndef CFG_INIT_RAM_LOCK #define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ #else @@ -265,20 +241,22 @@ #define CFG_PROMPT_HUSH_PS2 "> " #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 -#define CONFIG_OF_BOARD_SETUP 1 +/* + * Pass open firmware flat tree to kernel + */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 /* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 +#define OF_FLAT_TREE_MAX_SIZE 8192 -#define OF_CPU "PowerPC,8641@0" -#define OF_SOC "soc8641@f8000000" -#define OF_TBCLK (bd->bi_busfreq / 8) -#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500" +#define OF_CPU "PowerPC,8641@0" +#define OF_SOC "soc8641@f8000000" +#define OF_TBCLK (bd->bi_busfreq / 8) +#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500" -#define CFG_64BIT_VSPRINTF 1 -#define CFG_64BIT_STRTOUL 1 +#define CFG_64BIT_VSPRINTF 1 +#define CFG_64BIT_STRTOUL 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ @@ -297,13 +275,10 @@ * Addresses are mapped 1-1. */ #define CFG_PCI1_MEM_BASE 0x80000000 -//#define CFG_PCI1_MEM_BASE 0xd0000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CFG_PCI1_IO_BASE 0xe2000000 -//#define CFG_PCI1_IO_BASE 0xe0000000 #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -//#define CFG_PCI1_IO_BUS 0x00000000 #define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ /* For RTL8139 */ @@ -316,29 +291,18 @@ #define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE #define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */ -// #define CFG_PCI1_MEM_BASE 0x80000000 -// #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -// #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -// #define CFG_PCI1_IO_BASE 0xe2000000 -// #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -// #define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ - - #if defined(CONFIG_PCI) - #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -//#define CFG_SCSI_SCAN_BUS_REVERSE - +#undef CFG_SCSI_SCAN_BUS_REVERSE #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_RTL8139 - #undef CONFIG_EEPRO100 #undef CONFIG_TULIP @@ -349,7 +313,6 @@ #endif #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -//#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ @@ -371,7 +334,6 @@ #define CONFIG_MPC86XX_TSEC4 1 #define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4" - #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC3_PHY_ADDR 2 @@ -389,12 +351,10 @@ /* BAT0 2G Cacheable, non-guarded * 0x0000_0000 2G DDR */ -//#define CFG_DBAT0L (0x0 | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT0L (0x0 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE | BATL_MEMCOHERENCE) -#define CFG_DBAT0U (0x0 | BATU_BL_512M | BATU_VS | BATU_VP) -//#define CFG_IBAT0L CFG_DBAT0L -//#define CFG_IBAT0L (0x0 | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT0L (0x0| BATL_PP_RW | BATL_CACHEINHIBIT | BATL_MEMCOHERENCE) +#define CFG_DBAT0L ( BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE | BATL_MEMCOHERENCE ) +#define CFG_DBAT0U ( BATU_BL_512M | BATU_VS | BATU_VP ) +#define CFG_IBAT0L ( BATL_PP_RW | BATL_CACHEINHIBIT | BATL_MEMCOHERENCE) #define CFG_IBAT0U CFG_DBAT0U /* BAT1 1G Cache-inhibited, guarded @@ -402,7 +362,8 @@ * 0xa000_0000 512M PCI-Express 2 Memory ** SS - Changed it for operating from 0xd0000000 */ -#define CFG_DBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT1U CFG_DBAT1U @@ -410,7 +371,8 @@ /* BAT2 512M Cache-inhibited, guarded * 0xc000_0000 512M RapidIO Memory */ -#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) #define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT2U CFG_DBAT2U @@ -418,7 +380,8 @@ /* BAT3 4M Cache-inhibited, guarded * 0xf800_0000 4M CCSR */ -#define CFG_DBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) #define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT3U CFG_DBAT3U @@ -428,7 +391,8 @@ * 0xe300_0000 16M PCI-Express 2 I/0 ** SS - Note that this is at 0xe0000000 */ -#define CFG_DBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT4U CFG_DBAT4U @@ -444,12 +408,12 @@ /* BAT6 32M Cache-inhibited, guarded * 0xfe00_0000 32M FLASH */ -#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT6L ( CFG_FLASH_BASE | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) #define CFG_IBAT6U CFG_DBAT6U - #define CFG_DBAT7L 0x00000000 #define CFG_DBAT7U 0x00000000 #define CFG_IBAT7L 0x00000000 @@ -461,17 +425,17 @@ /* * Environment */ - #ifndef CFG_RAMBOOT - #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) - #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ - #define CFG_ENV_SIZE 0x2000 - #else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ - #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) - #define CFG_ENV_SIZE 0x2000 - #endif +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ @@ -572,24 +536,25 @@ #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD #endif -#define CONFIG_HAS_ETH1 1 -#define CONFIG_HAS_ETH2 1 -#define CONFIG_HAS_ETH3 1 +#define CONFIG_HAS_ETH1 1 +#define CONFIG_HAS_ETH2 1 +#define CONFIG_HAS_ETH3 1 -#define CONFIG_IPADDR 10.82.193.138 +#define CONFIG_IPADDR 10.82.193.138 #define CONFIG_HOSTNAME unknown #define CONFIG_ROOTPATH /opt/nfsroot #define CONFIG_BOOTFILE uImage -#define CONFIG_SERVERIP 10.82.193.104 -#define CONFIG_GATEWAYIP 10.82.193.254 -#define CONFIG_NETMASK 255.255.252.0 +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 10.82.193.104 +#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_LOADADDR 1000000 /* default location for tftp and bootm */ +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ -//#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ +//#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200" #define CONFIG_BAUDRATE 115200 @@ -599,7 +564,7 @@ "consoledev=ttyS0\0" \ "ramdiskaddr=400000\0" \ "ramdiskfile=your.ramdisk.u-boot\0" \ - "pex0=echo ---------------------------; echo --------- PCI EXPRESS -----\0" \ + "pex0=echo ---------------------------; echo --------- PCI EXPRESS -----\0"\ "pexstat=mw f8008000 84000004; echo -expect:- 16000000; md f8008004 1\0" \ "pex1=pci write 1.0.0 4 146; pci write 1.0.0 10 80000000\0" \ "pexd=echo -expect:- xxx01002 00100146; pci display 1.0.0 0 2\0" \ diff --git a/include/mpc86xx.h b/include/mpc86xx.h index 61b5279..4edeae1 100644 --- a/include/mpc86xx.h +++ b/include/mpc86xx.h @@ -1,5 +1,5 @@ /* - * Copyright 2004 Freescale Semiconductor. + * Copyright 2006 Freescale Semiconductor. * Jeffrey Brown (jeffrey@freescale.com) * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) */ @@ -9,7 +9,7 @@ #define EXC_OFF_SYS_RESET 0x0100 /* System reset offset */ -/*---------------------------------------------------------------- +/* * l2cr values. Look in config_<BOARD>.h for the actual setup */ #define l2cr 1017 @@ -23,7 +23,7 @@ #define L2CR_HWF 0x00000800 /* bit 20 - hardware flush */ #define L2CR_L2IP 0x00000001 /* global invalidate in progress */ -/*---------------------------------------------------------------- +/* * BAT settings. Look in config_<BOARD>.h for the actual setup */ |