diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/taihu.h | 473 | ||||
| -rw-r--r-- | include/configs/zeus.h | 375 | ||||
| -rw-r--r-- | include/dtt.h | 8 | ||||
| -rw-r--r-- | include/ppc405.h | 14 |
4 files changed, 870 insertions, 0 deletions
diff --git a/include/configs/taihu.h b/include/configs/taihu.h new file mode 100644 index 0000000..61814a8 --- /dev/null +++ b/include/configs/taihu.h @@ -0,0 +1,473 @@ +/* + * (C) Copyright 2000-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2005-2007 + * Beijing UD Technology Co., Ltd., taihusupport@amcc.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + + +#define CONFIG_405EP 1 /* this is a PPC405 CPU */ +#define CONFIG_4xx 1 /* member of PPC4xx family */ +#define CONFIG_TAIHU 1 /* on a taihu board */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f */ + +#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ + +#define CONFIG_NO_SERIAL_EEPROM + +/*----------------------------------------------------------------------------*/ +#ifdef CONFIG_NO_SERIAL_EEPROM + +/* +!------------------------------------------------------------------------------- +! PLL settings for 333MHz CPU, 111MHz PLB/SDRAM, 55MHz EBC, 33MHz PCI, +! assuming a 33MHz input clock to the 405EP from the C9531. +!------------------------------------------------------------------------------- +*/ +#define PLLMR0_333_111_55_37 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ + PLL_MALDIV_1 | PLL_PCIDIV_3) +#define PLLMR1_333_111_55_37 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) +#define PLLMR0_333_111_55_111 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ + PLL_MALDIV_1 | PLL_PCIDIV_1) +#define PLLMR1_333_111_55_111 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) + +#define PLLMR0_DEFAULT PLLMR0_333_111_55_37 +#define PLLMR1_DEFAULT PLLMR1_333_111_55_37 +#define PLLMR0_DEFAULT_PCI66 PLLMR0_333_111_55_111 +#define PLLMR1_DEFAULT_PCI66 PLLMR1_333_111_55_111 + +#endif +/*----------------------------------------------------------------------------*/ + +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootfile=/tftpboot/taihu/uImage\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "kernel_addr=FC000000\0" \ + "ramdisk_addr=FC180000\0" \ + "load=tftp 200000 /tftpboot/taihu/u-boot.bin\0" \ + "update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \ + "cp.b 200000 FFFC0000 40000\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0x14 /* PHY address */ +#define CONFIG_HAS_ETH1 +#define CONFIG_PHY1_ADDR 0x10 /* EMAC1 PHY address */ +#define CONFIG_NET_MULTI 1 +#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_PHY_RESET 1 + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_CACHE | \ + CFG_CMD_DHCP | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_SPI | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#undef CONFIG_SPD_EEPROM /* use SPD EEPROM for setup */ +#define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */ +#define CFG_SDRAM_BANKS 2 + +/* + * SDRAM configuration (please see cpu/ppc/sdram.[ch]) + */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ +#define CONFIG_SDRAM_BANK1 1 /* init onboard SDRAM bank 1 */ + +/* SDRAM timings used in datasheet */ +#define CFG_SDRAM_CL 3 /* CAS latency */ +#define CFG_SDRAM_tRP 20 /* PRECHARGE command period */ +#define CFG_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ +#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ +#define CFG_SDRAM_tRFC 66 /* Auto refresh period */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +/* + * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CFG_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. + * The Linux BASE_BAUD define should match this configuration. + * baseBaud = cpuClock/(uartDivisor*16) + * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, + * set Linux BASE_BAUD to 403200. + */ +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CFG_BASE_BAUD 691200 + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_UART1_CONSOLE 1 + + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * I2C stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ + +#if (CONFIG_COMMANDS & CFG_CMD_EEPROM) +#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#endif + + +#define CONFIG_SOFT_SPI +#define SPI_SCL spi_scl +#define SPI_SDA spi_sda +#define SPI_READ spi_read() +#define SPI_DELAY udelay(2) +#ifndef __ASSEMBLY__ +void spi_scl(int); +void spi_sda(int); +unsigned char spi_read(void); +#endif + +/* standard dtt sensor configuration */ +#define CONFIG_DTT_DS1775 1 +#define CONFIG_DTT_SENSORS { 0 } + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#define CFG_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ +#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_EEPRO100 1 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFE00000 +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ + +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_ADDR0 0x555 +#define CFG_FLASH_ADDR1 0x2aa +#define CFG_FLASH_WORD_SIZE unsigned short + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif /* CFG_ENV_IS_IN_FLASH */ + +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ +#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */ + +#ifdef CFG_ENV_IS_IN_NVRAM +#define CFG_ENV_SIZE 0x0ff8 /* Size of Environment vars */ +#define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env*/ +#endif + +/*----------------------------------------------------------------------- + * PPC405 GPIO Configuration + */ +#define CFG_440_GPIO_TABLE { /* GPIO Alternate1 */ \ +{ \ +/* GPIO Core 0 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast SPI CS */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO5 TS3 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO7 TS5 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 SPI SCLK */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 SPI DI */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 SPI DO */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 PCI INTA */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 PCI INTB */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 PCI INTC */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 PCI INTD */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 USB */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 EBC */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 unused */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD UART1 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx UART0 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 User LED1 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 User LED2 */ \ +} \ +} + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 16384 /* For IBM 405EP CPU */ +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xFC000000 /* FLASH bank #1 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory (OCM) for temperary stack until sdram is tested */ +#define CFG_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CFG_OCM_DATA_ADDR 0xF8000000 +#define CFG_OCM_DATA_SIZE 0x1000 +#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ +#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ + +/* Memory Bank 0 (Flash/SRAM) initialization */ +#define CFG_EBC_PB0AP 0x03815600 +#define CFG_EBC_PB0CR 0xFFE3A000 /* BAS=0xFFE,BS=2MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (NVRAM/RTC) initialization */ +#define CFG_EBC_PB1AP 0x05815600 +#define CFG_EBC_PB1CR 0xFC0BA000 /* BAS=0xFc0,BS=32MB,BU=R/W,BW=16bit */ + +/* Memory Bank 2 (USB device) initialization */ +#define CFG_EBC_PB2AP 0x03016600 +#define CFG_EBC_PB2CR 0x50018000 /* BAS=0x500,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 3 (LCM and D-flip-flop) initialization */ +#define CFG_EBC_PB3AP 0x158FF600 +#define CFG_EBC_PB3CR 0x50118000 /* BAS=0x501,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 4 (not install) initialization */ +#define CFG_EBC_PB4AP 0x158FF600 +#define CFG_EBC_PB4CR 0x5021A000 + +/*----------------------------------------------------------------------- + * Definitions for GPIO setup (PPC405EP specific) + * + * GPIO0[0] - External Bus Controller BLAST output + * GPIO0[1-9] - Instruction trace outputs + * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs + * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs + * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs + * GPIO0[24-27] - UART0 control signal inputs/outputs + * GPIO0[28-29] - UART1 data signal input/output + * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs + */ +#define CFG_GPIO0_OSRH 0x15555550 /* output select high/low */ +#define CFG_GPIO0_OSRL 0x00000110 +#define CFG_GPIO0_ISR1H 0x00000001 /* input select high/low */ +#define CFG_GPIO0_ISR1L 0x15545440 +#define CFG_GPIO0_TSRH 0x00000000 /* three-state select high/low */ +#define CFG_GPIO0_TSRL 0x00000000 +#define CFG_GPIO0_TCR 0xFFFE8117 /* three-state control */ +#define CFG_GPIO0_ODR 0x00000000 /* open drain */ + +#define GPIO0 0 /* GPIO controller 0 */ + +/* the GPIO macros in include/ppc405.h for High/Low registers are backwards */ + +#define GPIOx_OSL (GPIO0_OSRH-GPIO_BASE) +#define GPIOx_TSL (GPIO0_TSRH-GPIO_BASE) +#define GPIOx_IS1L (GPIO0_ISR1H-GPIO_BASE) +#define GPIOx_IS2L (GPIO0_ISR1H-GPIO_BASE) +#define GPIOx_IS3L (GPIO0_ISR1H-GPIO_BASE) + +#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO output select */ +#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO three-state select */ +#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO input select */ +#define GPIO_IS2(x) (x+GPIOx_IS1L) +#define GPIO_IS3(x) (x+GPIOx_IS1L) + +#define CPLD_REG0_ADDR 0x50100000 +#define CPLD_REG1_ADDR 0x50100001 +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/zeus.h b/include/configs/zeus.h new file mode 100644 index 0000000..86a16e7 --- /dev/null +++ b/include/configs/zeus.h @@ -0,0 +1,375 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * zeus.h - configuration for Zeus board + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_ZEUS 1 /* Board is Zeus */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_405EP 1 /* Specifc 405EP support*/ + +#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +#define PLLMR0_DEFAULT PLLMR0_333_111_55_111 +#define PLLMR1_DEFAULT PLLMR1_333_111_55_111 + +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0x01 /* PHY address */ +#define CONFIG_HAS_ETH1 1 +#define CONFIG_PHY1_ADDR 0x11 /* EMAC1 PHY address */ +#define CONFIG_NET_MULTI 1 +#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_PHY_RESET 1 +#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_CACHE | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_LOG | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO) + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_CACHE | \ + CFG_POST_UART | \ + CFG_POST_ETHER) + +#define CFG_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */ + +/* Define here the base-addresses of the UARTs to test in POST */ +#define CFG_POST_UART_TABLE {UART0_BASE} + +#define CONFIG_LOGBUFFER +#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ + +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * SDRAM + *----------------------------------------------------------------------*/ +/* + * SDRAM configuration (please see cpu/ppc/sdram.[ch]) + */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ +#define CONFIG_SDRAM_BANK1 1 /* init onboard SDRAM bank 1 */ + +/* SDRAM timings used in datasheet */ +#define CFG_SDRAM_CL 3 /* CAS latency */ +#define CFG_SDRAM_tRP 20 /* PRECHARGE command period */ +#define CFG_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ +#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ +#define CFG_SDRAM_tRFC 66 /* Auto refresh period */ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#define CFG_BASE_BAUD 691200 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* these are for the ST M24C02 2kbit serial i2c eeprom */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* base address */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 + +#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* write eeprom in pages */ +#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* 8 byte write page size */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +/* + * The layout of the I2C EEPROM, used for bootstrap setup and for board- + * specific values, like ethaddr... that can be restored via the sw-reset + * button + */ +#define FACTORY_RESET_I2C_EEPROM 0x50 +#define FACTORY_RESET_ENV_OFFS 0x80 +#define FACTORY_RESET_ENV_SIZE 0x80 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFF000000 +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 16384 /* For IBM 405EP CPU */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory (OCM) for temperary stack until sdram is tested */ +#define CFG_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CFG_OCM_DATA_ADDR 0xF8000000 +#define CFG_OCM_DATA_SIZE 0x1000 +#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of OCM */ +#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +/* reserve some memory for POST and BOOT limit info */ +#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16) + +/* extra data in OCM */ +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) +#define CFG_POST_MAGIC (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 8) +#define CFG_POST_VAL (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 12) + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ + +/* Memory Bank 0 (Flash 16M) initialization */ +#define CFG_EBC_PB0AP 0x05815600 +#define CFG_EBC_PB0CR 0xFF09A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */ + +/*----------------------------------------------------------------------- + * Definitions for GPIO setup (PPC405EP specific) + * + * GPIO0[0] - External Bus Controller BLAST output + * GPIO0[1-9] - Instruction trace outputs + * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs + * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs + * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs + * GPIO0[24-27] - UART0 control signal inputs/outputs + * GPIO0[28-29] - UART1 data signal input/output + * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs + */ +#define CFG_GPIO0_OSRH 0x15555550 /* Chip selects */ +#define CFG_GPIO0_OSRL 0x00000110 /* UART_DTR-pin 27 alt out */ +#define CFG_GPIO0_ISR1H 0x10000041 /* Pin 2, 12 is input */ +#define CFG_GPIO0_ISR1L 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */ +#define CFG_GPIO0_TSRH 0x00000000 +#define CFG_GPIO0_TSRL 0x00000000 +#define CFG_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */ +#define CFG_GPIO0_ODR 0x00000000 + +#define CFG_GPIO_SW_RESET 1 +#define CFG_GPIO_ZEUS_PE 12 +#define CFG_GPIO_LED_RED 22 +#define CFG_GPIO_LED_GREEN 23 + +/* Time in milli-seconds */ +#define CFG_TIME_POST 5000 +#define CFG_TIME_FACTORY_RESET 10000 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* ENVIRONMENT VARS */ + +#define CONFIG_PREBOOT "echo;echo Welcome to Bulletendpoints board v1.1;echo" +#define CONFIG_IPADDR 192.168.1.10 +#define CONFIG_SERVERIP 192.168.1.100 +#define CONFIG_GATEWAYIP 192.168.1.100 +#define CONFIG_ETHADDR 50:00:00:00:06:00 +#define CONFIG_ETH1ADDR 50:00:00:00:06:01 +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "logversion=2\0" \ + "hostname=zeus\0" \ + "netdev=eth0\0" \ + "ethact=ppc_4xx_eth0\0" \ + "netmask=255.255.255.0\0" \ + "ramdisk_size=50000\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw" \ + " nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw" \ + " ramdisk=${ramdisk_size}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0," \ + "${baudrate}\0" \ + "net_nfs=tftp ${kernel_mem_addr} ${file_kernel};" \ + "run nfsargs addip addtty;bootm\0" \ + "net_ram=tftp ${kernel_mem_addr} ${file_kernel};" \ + "tftp ${ramdisk_mem_addr} ${file_fs};" \ + "run ramargs addip addtty;" \ + "bootm ${kernel_mem_addr} ${ramdisk_mem_addr}\0" \ + "rootpath=/target_fs/zeus\0" \ + "kernel_fl_addr=ff000000\0" \ + "kernel_mem_addr=200000\0" \ + "ramdisk_fl_addr=ff300000\0" \ + "ramdisk_mem_addr=4000000\0" \ + "uboot_fl_addr=fffc0000\0" \ + "uboot_mem_addr=100000\0" \ + "file_uboot=/zeus/u-boot.bin\0" \ + "tftp_uboot=tftp 100000 ${file_uboot}\0" \ + "update_uboot=protect off fffc0000 ffffffff;" \ + "era fffc0000 ffffffff;cp.b 100000 fffc0000 40000;" \ + "protect on fffc0000 ffffffff\0" \ + "upd_uboot=run tftp_uboot;run update_uboot\0" \ + "file_kernel=/zeus/uImage_ba\0" \ + "tftp_kernel=tftp 100000 ${file_kernel}\0" \ + "update_kernel=protect off ff000000 ff17ffff;" \ + "era ff000000 ff17ffff;cp.b 100000 ff000000 180000\0" \ + "upd_kernel=run tftp_kernel;run update_kernel\0" \ + "file_fs=/zeus/rootfs_ba.img\0" \ + "tftp_fs=tftp 100000 ${file_fs}\0" \ + "update_fs=protect off ff300000 ff87ffff;era ff300000 ff87ffff;"\ + "cp.b 100000 ff300000 580000\0" \ + "upd_fs=run tftp_fs;run update_fs\0" \ + "bootcmd=chkreset;run ramargs addip addtty addmisc;" \ + "bootm ${kernel_fl_addr} ${ramdisk_fl_addr}\0" \ + "" + +#endif /* __CONFIG_H */ diff --git a/include/dtt.h b/include/dtt.h index 842a761..2e8c690 100644 --- a/include/dtt.h +++ b/include/dtt.h @@ -29,6 +29,7 @@ #if defined(CONFIG_DTT_LM75) || \ defined(CONFIG_DTT_DS1621) || \ + defined(CONFIG_DTT_DS1775) || \ defined(CONFIG_DTT_LM81) || \ defined(CONFIG_DTT_ADM1021) @@ -78,6 +79,13 @@ extern int dtt_get_temp(int sensor); #define DTT_CONFIG 0xAC #endif +#if defined(CONFIG_DTT_DS1775) +#define DTT_READ_TEMP 0x0 +#define DTT_CONFIG 0x1 +#define DTT_TEMP_HYST 0x2 +#define DTT_TEMP_OS 0x3 +#endif + #if defined(CONFIG_DTT_ADM1021) #define DTT_READ_LOC_VALUE 0x00 #define DTT_READ_REM_VALUE 0x01 diff --git a/include/ppc405.h b/include/ppc405.h index e4522e7..0c7bf3e 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -541,6 +541,18 @@ #define PLLMR1_266_66_33_33 (PLL_FBKDIV_8 | \ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) +#define PLLMR0_333_111_55_37 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ + PLL_MALDIV_1 | PLL_PCIDIV_3) +#define PLLMR1_333_111_55_37 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) +#define PLLMR0_333_111_55_111 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ + PLL_MALDIV_1 | PLL_PCIDIV_1) +#define PLLMR1_333_111_55_111 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) /* * PLL Voltage Controlled Oscillator (VCO) definitions @@ -1228,6 +1240,8 @@ #define mtebc(reg, data) mtdcr(ebccfga,reg);mtdcr(ebccfgd,data) #define mfebc(reg, data) mtdcr(ebccfga,reg);data = mfdcr(ebccfgd) +#define mtsdram(reg, data) do { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } while (0) +#define mfsdram(reg, data) do { mtdcr(memcfga,reg);data = mfdcr(memcfgd); } while (0) #ifndef __ASSEMBLY__ |