diff options
Diffstat (limited to 'include/i2c.h')
| -rw-r--r-- | include/i2c.h | 215 |
1 files changed, 206 insertions, 9 deletions
diff --git a/include/i2c.h b/include/i2c.h index c60d075..457fd7d 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -1,4 +1,8 @@ /* + * Copyright (C) 2009 Sergey Kubushyn <ksi@koi8.net> + * Copyright (C) 2009 - 2013 Heiko Schocher <hs@denx.de> + * Changes for multibus/multiadapter I2C support. + * * (C) Copyright 2001 * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com. * @@ -46,16 +50,14 @@ */ #define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */ -#ifdef CONFIG_I2C_MULTI_BUS -#define MAX_I2C_BUS 2 -#define I2C_MULTI_BUS 1 +#if !defined(CONFIG_SYS_I2C_MAX_HOPS) +/* no muxes used bus = i2c adapters */ +#define CONFIG_SYS_I2C_DIRECT_BUS 1 +#define CONFIG_SYS_I2C_MAX_HOPS 0 +#define CONFIG_SYS_NUM_I2C_BUSES ll_entry_count(struct i2c_adapter, i2c) #else -#define MAX_I2C_BUS 1 -#define I2C_MULTI_BUS 0 -#endif - -#if !defined(CONFIG_SYS_MAX_I2C_BUS) -#define CONFIG_SYS_MAX_I2C_BUS MAX_I2C_BUS +/* we use i2c muxes */ +#undef CONFIG_SYS_I2C_DIRECT_BUS #endif /* define the I2C bus number for RTC and DTT if not already done */ @@ -69,6 +71,88 @@ #define CONFIG_SYS_SPD_BUS_NUM 0 #endif +struct i2c_adapter { + void (*init)(struct i2c_adapter *adap, int speed, + int slaveaddr); + int (*probe)(struct i2c_adapter *adap, uint8_t chip); + int (*read)(struct i2c_adapter *adap, uint8_t chip, + uint addr, int alen, uint8_t *buffer, + int len); + int (*write)(struct i2c_adapter *adap, uint8_t chip, + uint addr, int alen, uint8_t *buffer, + int len); + uint (*set_bus_speed)(struct i2c_adapter *adap, + uint speed); + int speed; + int slaveaddr; + int init_done; + int hwadapnr; + char *name; +}; + +#define U_BOOT_I2C_MKENT_COMPLETE(_init, _probe, _read, _write, \ + _set_speed, _speed, _slaveaddr, _hwadapnr, _name) \ + { \ + .init = _init, \ + .probe = _probe, \ + .read = _read, \ + .write = _write, \ + .set_bus_speed = _set_speed, \ + .speed = _speed, \ + .slaveaddr = _slaveaddr, \ + .init_done = 0, \ + .hwadapnr = _hwadapnr, \ + .name = #_name \ +}; + +#define U_BOOT_I2C_ADAP_COMPLETE(_name, _init, _probe, _read, _write, \ + _set_speed, _speed, _slaveaddr, _hwadapnr) \ + ll_entry_declare(struct i2c_adapter, _name, i2c) = \ + U_BOOT_I2C_MKENT_COMPLETE(_init, _probe, _read, _write, \ + _set_speed, _speed, _slaveaddr, _hwadapnr, _name); + +struct i2c_adapter *i2c_get_adapter(int index); + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS +struct i2c_mux { + int id; + char name[16]; +}; + +struct i2c_next_hop { + struct i2c_mux mux; + uint8_t chip; + uint8_t channel; +}; + +struct i2c_bus_hose { + int adapter; + struct i2c_next_hop next_hop[CONFIG_SYS_I2C_MAX_HOPS]; +}; +#define I2C_NULL_HOP {{-1, ""}, 0, 0} +extern struct i2c_bus_hose i2c_bus[]; + +#define I2C_ADAPTER(bus) i2c_bus[bus].adapter +#else +#define I2C_ADAPTER(bus) bus +#endif +#define I2C_BUS gd->cur_i2c_bus + +#define I2C_ADAP_NR(bus) i2c_get_adapter(I2C_ADAPTER(bus)) +#define I2C_ADAP I2C_ADAP_NR(gd->cur_i2c_bus) +#define I2C_ADAP_HWNR (I2C_ADAP->hwadapnr) + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS +#define I2C_MUX_PCA9540_ID 1 +#define I2C_MUX_PCA9540 {I2C_MUX_PCA9540_ID, "PCA9540B"} +#define I2C_MUX_PCA9542_ID 2 +#define I2C_MUX_PCA9542 {I2C_MUX_PCA9542_ID, "PCA9542A"} +#define I2C_MUX_PCA9544_ID 3 +#define I2C_MUX_PCA9544 {I2C_MUX_PCA9544_ID, "PCA9544A"} +#define I2C_MUX_PCA9547_ID 4 +#define I2C_MUX_PCA9547 {I2C_MUX_PCA9547_ID, "PCA9547A"} +#endif + #ifndef I2C_SOFT_DECLARATIONS # if defined(CONFIG_MPC8260) # define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT); @@ -134,6 +218,104 @@ int i2x_mux_select_mux(int bus); int i2c_mux_ident_muxstring_f (uchar *buf); #endif +#ifdef CONFIG_SYS_I2C +/* + * Initialization, must be called once on start up, may be called + * repeatedly to change the speed and slave addresses. + */ +void i2c_init(unsigned int speed, int slaveaddr); +#ifdef CONFIG_SYS_I2C_INIT_BOARD +void i2c_init_board(void); +#endif + +/* + * i2c_get_bus_num: + * + * Returns index of currently active I2C bus. Zero-based. + */ +unsigned int i2c_get_bus_num(void); + +/* + * i2c_set_bus_num: + * + * Change the active I2C bus. Subsequent read/write calls will + * go to this one. + * + * bus - bus index, zero based + * + * Returns: 0 on success, not 0 on failure + * + */ +int i2c_set_bus_num(unsigned int bus); + +/* + * i2c_init_all(): + * + * Initializes all I2C adapters in the system. All i2c_adap structures must + * be initialized beforehead with function pointers and data, including + * speed and slaveaddr. Returns 0 on success, non-0 on failure. + */ +void i2c_init_all(void); + +/* + * Probe the given I2C chip address. Returns 0 if a chip responded, + * not 0 on failure. + */ +int i2c_probe(uint8_t chip); + +/* + * Read/Write interface: + * chip: I2C chip address, range 0..127 + * addr: Memory (register) address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Where to read/write the data + * len: How many bytes to read/write + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_read(uint8_t chip, unsigned int addr, int alen, + uint8_t *buffer, int len); + +int i2c_write(uint8_t chip, unsigned int addr, int alen, + uint8_t *buffer, int len); + +/* + * Utility routines to read/write registers. + */ +uint8_t i2c_reg_read(uint8_t addr, uint8_t reg); + +void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val); + +/* + * i2c_set_bus_speed: + * + * Change the speed of the active I2C bus + * + * speed - bus speed in Hz + * + * Returns: new bus speed + * + */ +unsigned int i2c_set_bus_speed(unsigned int speed); + +/* + * i2c_get_bus_speed: + * + * Returns speed of currently active I2C bus in Hz + */ + +unsigned int i2c_get_bus_speed(void); + +/* + * i2c_reloc_fixup: + * + * Adjusts I2C pointers after U-Boot is relocated to DRAM + */ +void i2c_reloc_fixup(void); +#else + /* * Probe the given I2C chip address. Returns 0 if a chip responded, * not 0 on failure. @@ -235,6 +417,21 @@ int i2c_set_bus_speed(unsigned int); */ unsigned int i2c_get_bus_speed(void); +#endif /* CONFIG_SYS_I2C */ + +/* + * only for backwardcompatibility, should go away if we switched + * completely to new multibus support. + */ +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS) +# if !defined(CONFIG_SYS_MAX_I2C_BUS) +# define CONFIG_SYS_MAX_I2C_BUS 2 +# endif +# define I2C_MULTI_BUS 0 +#else +# define CONFIG_SYS_MAX_I2C_BUS 1 +# define I2C_MULTI_BUS 0 +#endif /* NOTE: These two functions MUST be always_inline to avoid code growth! */ static inline unsigned int I2C_GET_BUS(void) __attribute__((always_inline)); |