diff options
Diffstat (limited to 'include/configs')
123 files changed, 1299 insertions, 388 deletions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 694a87b..5cb0f1e 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -160,8 +160,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h index 91369a7..49a86fd 100644 --- a/include/configs/ATUM8548.h +++ b/include/configs/ATUM8548.h @@ -243,27 +243,27 @@ */ #define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ #ifdef CONFIG_PCI2 -#define CONFIG_SYS_PCI2_MEM_BASE 0xC0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE +#define CONFIG_SYS_PCI2_MEM_BUS 0xC0000000 +#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BUS #define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI2_IO_BUS 0x00000000 #define CONFIG_SYS_PCI2_IO_PHYS 0xe2800000 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ #endif #ifdef CONFIG_PCIE1 -#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */ #endif diff --git a/include/configs/B2.h b/include/configs/B2.h index e5439f3..f51a261 100644 --- a/include/configs/B2.h +++ b/include/configs/B2.h @@ -58,7 +58,7 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x04000300 /* base address */ #define CONFIG_SMC_USE_32_BIT #undef CONFIG_SHOW_ACTIVITY @@ -98,7 +98,7 @@ #define CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C - +#define CONFIG_NET_MULTI #define CONFIG_BOOTDELAY 5 #define CONFIG_ETHADDR 00:50:c2:1e:af:fb #define CONFIG_BOOTARGS "setenv bootargs root=/dev/ram ip=192.168.0.70:::::eth0:off \ diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h index 2384925..ae8494d 100644 --- a/include/configs/CMS700.h +++ b/include/configs/CMS700.h @@ -165,8 +165,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is diff --git a/include/configs/DU440.h b/include/configs/DU440.h index e9ea1bf..65dc235 100644 --- a/include/configs/DU440.h +++ b/include/configs/DU440.h @@ -60,8 +60,9 @@ #define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 -#define CONFIG_SYS_PCI_IOBASE 0xe8000000 - +#define CONFIG_SYS_PCI_IOBASE 0xe8000000 +#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH +#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */ /* Don't change either of these */ #define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 1a2266f..9233523 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -219,8 +219,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h index 518d94d..ea502d4 100644 --- a/include/configs/HUB405.h +++ b/include/configs/HUB405.h @@ -160,8 +160,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- diff --git a/include/configs/IDS8247.h b/include/configs/IDS8247.h index 147a8b2..71bb7b4 100644 --- a/include/configs/IDS8247.h +++ b/include/configs/IDS8247.h @@ -263,8 +263,6 @@ #define CONFIG_SYS_NAND0_BASE 0xE1000000 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #endif /* CONFIG_CMD_NAND */ /*----------------------------------------------------------------------- diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 5927e76..0a4ba29 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -236,7 +236,6 @@ #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index 8eaff5d..cfed4ca 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -25,6 +25,11 @@ #ifndef __CONFIG_H #define __CONFIG_H +#ifdef CONFIG_MK_NAND +#define CONFIG_NAND_U_BOOT 1 +#define CONFIG_RAMBOOT_TEXT_BASE 0x00100000 +#endif + /* * High Level Configuration Options */ @@ -51,20 +56,29 @@ HRCWL_SVCOD_DIV_2 |\ HRCWL_CSB_TO_CLKIN_2X1 |\ HRCWL_CORE_TO_CSB_3X1) -#define CONFIG_SYS_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH_BASE (\ HRCWH_PCI_HOST |\ HRCWH_PCI1_ARBITER_ENABLE |\ HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0X00000100 |\ HRCWH_BOOTSEQ_DISABLE |\ HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_RL_EXT_LEGACY |\ HRCWH_TSEC1M_IN_RGMII |\ HRCWH_TSEC2M_IN_RGMII |\ HRCWH_BIG_ENDIAN |\ HRCWH_LALE_NORMAL) +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_ROM_LOC_NAND_SP_8BIT |\ + HRCWH_RL_EXT_NAND) +#else +#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY) +#endif + /* * System IO Config */ @@ -79,6 +93,10 @@ */ #define CONFIG_SYS_IMMR 0xE0000000 +#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR +#endif + /* * Arbiter Setup */ @@ -161,12 +179,6 @@ */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ @@ -200,10 +212,10 @@ #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */ -#define CONFIG_SYS_BR0_PRELIM ( CONFIG_SYS_FLASH_BASE /* Flash Base address */ \ +#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ | (2 << BR_PS_SHIFT) /* 16 bit port size */ \ | BR_V ) /* valid */ -#define CONFIG_SYS_OR0_PRELIM ( (~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ +#define CONFIG_SYS_NOR_OR_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ | OR_UPM_XAM \ | OR_GPCM_CSNT \ | OR_GPCM_ACS_DIV2 \ @@ -223,19 +235,31 @@ /* * NAND Flash on the Local Bus */ -#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ + +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_BASE 0xFFF00000 +#else +#define CONFIG_SYS_NAND_BASE 0xE0600000 +#endif + #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE 1 #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 + +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 +#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 -#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_NAND_BASE \ +#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V ) /* valid */ -#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFF8000 /* length 32K */ \ | OR_FCM_CSCT \ | OR_FCM_CST \ | OR_FCM_CHT \ @@ -244,9 +268,31 @@ | OR_FCM_EHTR ) /* 0xFFFF8396 */ +#ifdef CONFIG_NAND_U_BOOT +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM +#else +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM +#endif + #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM + +#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \ + !defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + /* * Serial Port */ @@ -255,7 +301,7 @@ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} @@ -409,7 +455,16 @@ /* * Environment */ -#ifndef CONFIG_SYS_RAMBOOT +#if defined(CONFIG_NAND_U_BOOT) + #define CONFIG_ENV_IS_IN_NAND 1 + #define CONFIG_ENV_OFFSET (512 * 1024) + #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE + #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE + #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4) + #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ + CONFIG_ENV_RANGE) +#elif !defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ @@ -443,7 +498,7 @@ #define CONFIG_CMD_DATE #define CONFIG_CMD_PCI -#if defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT) #undef CONFIG_CMD_SAVEENV #undef CONFIG_CMD_LOADS #endif @@ -505,7 +560,8 @@ /* FLASH: icache cacheable, but dcache-inhibit and guarded */ #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | \ + BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h index 6cee78a..1d1f94f 100644 --- a/include/configs/MPC8360ERDK.h +++ b/include/configs/MPC8360ERDK.h @@ -213,7 +213,6 @@ #define CONFIG_NAND_FSL_UPM 1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001b /* Access window size 4K */ diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index abeb6a2..63f1d85 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -321,9 +321,6 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 - /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 7ef92f7..913184c 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -343,9 +343,6 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 - /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index a847275..87901b3 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -70,13 +70,6 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); extern unsigned long get_board_ddr_clk(unsigned long dummy); @@ -440,10 +433,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 - - /* * I2C */ diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 4af599b..78bb74b 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -260,9 +260,6 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index a8f206f..e945da2 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -46,13 +46,6 @@ #define CONFIG_FSL_VIA -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_clock_freq(void); #endif @@ -293,9 +286,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 0caf456..799d946 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -50,13 +50,6 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif @@ -249,9 +242,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 - /* I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index e69ba90..3eb0049 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -52,13 +52,6 @@ #define CONFIG_FSL_VIA -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_clock_freq(void); #endif @@ -316,9 +309,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 94952dc..07a8e61 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -46,13 +46,6 @@ #define CONFIG_FSL_VIA -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_clock_freq(void); #endif @@ -291,9 +284,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index df59aca..4a4a9ed 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -253,9 +253,6 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 7b8c6c7..128a7e1 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -44,13 +44,6 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the MDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_clock_freq(void); #endif /*Replace a call to get_clock_freq (after it is implemented)*/ @@ -277,9 +270,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 17ea3bb..e16f0e1 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -44,13 +44,6 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the MDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_clock_freq(void); #endif @@ -254,9 +247,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ @@ -287,6 +277,10 @@ extern unsigned long get_clock_freq(void); #define PLPDIR1_I2C_BIT_MASK 0x0000000F #define PLPDIR1_I2C2_VAL 0x0000000F #define PLPDIR1_ESDHC_VAL 0x00000006 +#define PLPPAR1_UART0_BIT_MASK 0x00000fc0 +#define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80 +#define PLPDIR1_UART0_BIT_MASK 0x00000fc0 +#define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80 /* * General PCI diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 000f8f6..78b7369 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -53,13 +53,6 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); extern unsigned long get_board_ddr_clk(unsigned long dummy); @@ -105,7 +98,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) /* DDR Setup */ -#define CONFIG_SYS_DDR_TLB_START 9 #define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE @@ -374,9 +366,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* new uImage format support */ #define CONFIG_FIT 1 #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 7cb4ccd..1d2d659 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -251,9 +251,6 @@ /* maximum size of the flat tree (8K) */ #define OF_FLAT_TREE_MAX_SIZE 8192 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index a46f7c8..12a8f60 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -301,10 +301,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/MVBLUE.h b/include/configs/MVBLUE.h index 79c2069..669816c 100644 --- a/include/configs/MVBLUE.h +++ b/include/configs/MVBLUE.h @@ -88,7 +88,6 @@ #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_FLASH #define CONFIG_CMD_IMI -#define CONFIG_CMD_IRQ #define CONFIG_CMD_NET #define CONFIG_CMD_PCI #define CONFIG_CMD_RUN diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index e2930c1..15bfeef 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -149,8 +149,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 #define CONFIG_SYS_DDR_SBE 0x00FF0000 -#define CONFIG_SYS_DDR_TLB_START 9 - /* * Memory map * @@ -310,9 +308,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* new uImage format support */ #define CONFIG_FIT 1 #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index b48c199..f4509bd 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -54,13 +54,6 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - #ifndef __ASSEMBLY__ extern unsigned long calculate_board_sys_clk(unsigned long dummy); extern unsigned long calculate_board_ddr_clk(unsigned long dummy); @@ -108,7 +101,6 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) /* DDR Setup */ -#define CONFIG_SYS_DDR_TLB_START 9 #define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR3 1 #undef CONFIG_FSL_DDR_INTERACTIVE @@ -408,9 +400,6 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* new uImage format support */ #define CONFIG_FIT 1 #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index 2e41526..3d59454 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -99,8 +99,6 @@ #define CONFIG_SUPPORT_VFAT -#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */ - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ @@ -183,8 +181,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* * PCI stuff */ @@ -266,10 +262,10 @@ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFA0000 -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserve 384kB for malloc() */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (~(TEXT_BASE) + 1) +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* * Environment Variable setup @@ -300,7 +296,8 @@ /* * External Bus Controller (EBC) Setup */ -#define CAN_BA 0xF0000000 /* CAN Base Address */ +#define CAN0_BA 0xF0000000 /* CAN0 Base Address */ +#define CAN1_BA 0xF0000100 /* CAN1 Base Address */ #define DUART0_BA 0xF0000400 /* DUART Base Address */ #define DUART1_BA 0xF0000408 /* DUART Base Address */ #define RTC_BA 0xF0000500 /* RTC Base Address */ @@ -427,4 +424,14 @@ #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" #define CONFIG_USB_STORAGE 1 +/* + * UBI + */ +#define CONFIG_CMD_UBI +#define CONFIG_RBTREE +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_LZO + #endif /* __CONFIG_H */ diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index d6e2f6b..6310cfc 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -351,7 +351,6 @@ #define CONFIG_CMD_BSP #define CONFIG_CMD_DATE -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT #define CONFIG_CMD_DIAG @@ -359,7 +358,6 @@ #define CONFIG_CMD_ELF #define CONFIG_CMD_FAT #define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_NET @@ -435,11 +433,14 @@ /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT #define CONFIG_SYS_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ /* PCI identification */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ #define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */ #define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */ +/* for weak __pci_target_init() */ +#define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH #define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC #define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index 6fba0ca..8e9d928 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -211,8 +211,6 @@ *----------------------------------------------------------------------- */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* * nand device 1 on dave (PPChameleonEVB) needs more time, * so we just introduce additional wait in nand_wait(), diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h index f68d834..36e952e 100644 --- a/include/configs/SIMPC8313.h +++ b/include/configs/SIMPC8313.h @@ -132,7 +132,6 @@ #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h index 6eaa61d..12a7eda 100644 --- a/include/configs/TQM8272.h +++ b/include/configs/TQM8272.h @@ -442,8 +442,6 @@ WRITE_NAND(d, addr); \ } while(0) -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #endif /* CONFIG_CMD_NAND */ #define CONFIG_PCI diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index 1fbf4bf..d44fb07 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -372,8 +372,6 @@ #define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #endif /* CONFIG_NAND */ /* diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h index 17397e8..38a1d0d 100644 --- a/include/configs/VOH405.h +++ b/include/configs/VOH405.h @@ -169,8 +169,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h index dbfa1aa..5c281a1 100644 --- a/include/configs/WUH405.h +++ b/include/configs/WUH405.h @@ -157,8 +157,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- diff --git a/include/configs/XPEDITE5170.h b/include/configs/XPEDITE5170.h index 1a810e4..c63fd42 100644 --- a/include/configs/XPEDITE5170.h +++ b/include/configs/XPEDITE5170.h @@ -239,9 +239,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/XPEDITE5200.h b/include/configs/XPEDITE5200.h index 3f73780..1a56c60 100644 --- a/include/configs/XPEDITE5200.h +++ b/include/configs/XPEDITE5200.h @@ -213,9 +213,6 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h index 7782df3..7fd3668 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/XPEDITE5370.h @@ -244,9 +244,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/a320evb.h b/include/configs/a320evb.h new file mode 100644 index 0000000..fcc5563 --- /dev/null +++ b/include/configs/a320evb.h @@ -0,0 +1,222 @@ +/* + * (C) Copyright 2009 Faraday Technology + * Po-Yu Chuang <ratbert@faraday-tech.com> + * + * Configuation settings for the Faraday A320 board. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/a320.h> + +/*----------------------------------------------------------------------- + * CPU and Board Configuration Options + */ +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#undef CONFIG_SKIP_LOWLEVEL_INIT + +/*----------------------------------------------------------------------- + * Timer + */ +#define CONFIG_SYS_HZ 1000 /* timer ticks per second */ + +/*----------------------------------------------------------------------- + * Real Time Clock + */ +#define CONFIG_RTC_FTRTC010 + +/*----------------------------------------------------------------------- + * Serial console configuration + */ + +/* FTUART is a high speed NS 16C550A compatible UART */ +#define CONFIG_BAUDRATE 38400 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_COM1 0x98200000 +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_CLK 18432000 + +/* valid baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/*----------------------------------------------------------------------- + * Ethernet + */ +#define CONFIG_NET_MULTI +#define CONFIG_FTMAC100 + +#define CONFIG_BOOTDELAY 3 + +/*----------------------------------------------------------------------- + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_PING + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "A320 # " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 16 + +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4 * 1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4 * 1024) /* FIQ stack */ +#endif + +/*----------------------------------------------------------------------- + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) + +/*----------------------------------------------------------------------- + * size in bytes reserved for initial data +*/ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/*----------------------------------------------------------------------- + * SDRAM controller configuration + */ +#define CONFIG_SYS_FTSDMC020_TP0 (FTSDMC020_TP0_TRAS(2) | \ + FTSDMC020_TP0_TRP(1) | \ + FTSDMC020_TP0_TRCD(1) | \ + FTSDMC020_TP0_TRF(3) | \ + FTSDMC020_TP0_TWR(1) | \ + FTSDMC020_TP0_TCL(2)) + +#define CONFIG_SYS_FTSDMC020_TP1 (FTSDMC020_TP1_INI_PREC(4) | \ + FTSDMC020_TP1_INI_REFT(8) | \ + FTSDMC020_TP1_REF_INTV(0x180)) + +#define CONFIG_SYS_FTSDMC020_BANK0_BSR (FTSDMC020_BANK_ENABLE | \ + FTSDMC020_BANK_DDW_X16 | \ + FTSDMC020_BANK_DSZ_256M | \ + FTSDMC020_BANK_MBW_32 | \ + FTSDMC020_BANK_SIZE_64M) + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ + +/* + * Load address and memory test area should agree with + * board/faraday/a320/config.mk. Be careful not to overwrite U-boot itself. + */ +#define CONFIG_SYS_LOAD_ADDR 0x12000000 + +/* memtest works on 63 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x13F00000 + +/*----------------------------------------------------------------------- + * Static memory controller configuration + */ + +#include <asm/arch/ftsmc020.h> + +#define FTSMC020_BANK0_CONFIG (FTSMC020_BANK_ENABLE | \ + FTSMC020_BANK_BASE(PHYS_FLASH_1) | \ + FTSMC020_BANK_SIZE_1M | \ + FTSMC020_BANK_MBW_8) + +#define FTSMC020_BANK0_TIMING (FTSMC020_TPR_RBE | \ + FTSMC020_TPR_AST(3) | \ + FTSMC020_TPR_CTW(3) | \ + FTSMC020_TPR_ATI(0xf) | \ + FTSMC020_TPR_AT2(3) | \ + FTSMC020_TPR_WTC(3) | \ + FTSMC020_TPR_AHT(3) | \ + FTSMC020_TPR_TRNA(0xf)) + +#define FTSMC020_BANK1_CONFIG (FTSMC020_BANK_ENABLE | \ + FTSMC020_BANK_BASE(PHYS_FLASH_2) | \ + FTSMC020_BANK_SIZE_32M | \ + FTSMC020_BANK_MBW_32) + +#define FTSMC020_BANK1_TIMING (FTSMC020_TPR_AST(3) | \ + FTSMC020_TPR_CTW(3) | \ + FTSMC020_TPR_ATI(0xf) | \ + FTSMC020_TPR_AT2(3) | \ + FTSMC020_TPR_WTC(3) | \ + FTSMC020_TPR_AHT(3) | \ + FTSMC020_TPR_TRNA(0xf)) + +#define CONFIG_SYS_FTSMC020_CONFIGS { \ + { FTSMC020_BANK0_CONFIG, FTSMC020_BANK0_TIMING, }, \ + { FTSMC020_BANK1_CONFIG, FTSMC020_BANK1_TIMING, }, \ +} + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +/* use CFI framework */ +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER + +/* support JEDEC */ +#define CONFIG_FLASH_CFI_LEGACY +#define CONFIG_SYS_FLASH_LEGACY_512Kx8 + +#define PHYS_FLASH_1 0x00000000 +#define PHYS_FLASH_2 0x00400000 +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 +#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2, } + +#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 + +/* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 + +/* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 + +#undef CONFIG_SYS_FLASH_EMPTY_INFO + +/* environments */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR 0x00060000 +#define CONFIG_ENV_SIZE 0x20000 + +#endif /* __CONFIG_H */ diff --git a/include/configs/acadia.h b/include/configs/acadia.h index 2fb48b6..bd3388f 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -266,8 +266,6 @@ #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) #define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ diff --git a/include/configs/afeb9260.h b/include/configs/afeb9260.h index 74677d8..58b8c8c 100644 --- a/include/configs/afeb9260.h +++ b/include/configs/afeb9260.h @@ -107,7 +107,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* NOR flash - no real flash on this board */ diff --git a/include/configs/alpr.h b/include/configs/alpr.h index e6248e9..0fed9ad 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -231,18 +231,14 @@ */ #include <config_cmd_default.h> -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_EEPROM #define CONFIG_CMD_FPGA #define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING #undef CONFIG_CMD_NFS #undef CONFIG_WATCHDOG /* watchdog disabled */ diff --git a/include/configs/apollon.h b/include/configs/apollon.h index 575f60e..c1295de 100644 --- a/include/configs/apollon.h +++ b/include/configs/apollon.h @@ -76,6 +76,7 @@ * Size of malloc() pool */ #define CONFIG_ENV_SIZE SZ_128K /* Total Size of Environment Sector */ +#define CONFIG_ENV_SIZE_FLEX SZ_256K #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_1M) /* bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_SIZE 128 @@ -87,7 +88,8 @@ /* * SMC91c96 Etherent */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE (APOLLON_CS1_BASE+0x300) #define CONFIG_LAN91C96_EXT_PHY @@ -183,10 +185,8 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "Apollon # " - #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "Apollon # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) @@ -255,8 +255,7 @@ #define CONFIG_SYS_MONITOR_LEN SZ_256K /* U-Boot image size */ #define CONFIG_ENV_IS_IN_ONENAND 1 #define CONFIG_ENV_ADDR 0x00020000 - -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +#define CONFIG_ENV_ADDR_FLEX 0x00040000 #ifdef CONFIG_SYS_USE_UBI #define CONFIG_CMD_MTDPARTS diff --git a/include/configs/aria.h b/include/configs/aria.h index 2938eac..f89fc57 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -251,8 +251,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* * Configuration parameters for MPC5121 NAND driver */ diff --git a/include/configs/assabet.h b/include/configs/assabet.h index 8c5b84c..d17d4bd 100644 --- a/include/configs/assabet.h +++ b/include/configs/assabet.h @@ -53,7 +53,8 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_LAN91C96 /* we have an SMC9194 on-board */ +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 /* we have an SMC9194 on-board */ #define CONFIG_LAN91C96_BASE 0x18000000 /* diff --git a/include/configs/at91cap9adk.h b/include/configs/at91cap9adk.h index cc194d8..322718f 100644 --- a/include/configs/at91cap9adk.h +++ b/include/configs/at91cap9adk.h @@ -131,7 +131,6 @@ #define CONFIG_SYS_NAND_BASE 0x40000000 #define CONFIG_SYS_NAND_DBW_8 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Ethernet */ diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h index 3507de2..0509011 100644 --- a/include/configs/at91sam9260ek.h +++ b/include/configs/at91sam9260ek.h @@ -123,7 +123,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* NOR flash - no real flash on this board */ diff --git a/include/configs/at91sam9261ek.h b/include/configs/at91sam9261ek.h index f86698f..fbf7389 100644 --- a/include/configs/at91sam9261ek.h +++ b/include/configs/at91sam9261ek.h @@ -133,7 +133,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC15 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* NOR flash - no real flash on this board */ diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index a1582fc..571351c 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -267,7 +267,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA22 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Ethernet */ diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h index b460188..06184e7 100644 --- a/include/configs/at91sam9m10g45ek.h +++ b/include/configs/at91sam9m10g45ek.h @@ -118,7 +118,6 @@ /* NOR flash, if populated */ #ifndef CONFIG_CMD_NAND #define CONFIG_SYS_NO_FLASH 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #else #define CONFIG_SYS_FLASH_CFI 1 #define CONFIG_FLASH_CFI_DRIVER 1 @@ -142,7 +141,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Ethernet */ diff --git a/include/configs/at91sam9rlek.h b/include/configs/at91sam9rlek.h index b83266d..6fad75d 100644 --- a/include/configs/at91sam9rlek.h +++ b/include/configs/at91sam9rlek.h @@ -119,7 +119,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PB6 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD17 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Ethernet - not present */ diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index 0b87418..0fbd8f4 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -87,9 +87,6 @@ # define CONFIG_CMD_SPIBOOTLDR # endif #endif -#ifdef CONFIG_CMD_NAND -# define CONFIG_SYS_64BIT_VSPRINTF -#endif /* * Console Settings diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 3dddccf..ac9b3c5 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -593,7 +593,7 @@ #define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FPGA_BASE | 0x3a000) /* BAS=FPGA,BS=2MB,BU=R/W,BW=16bit*/ #endif /* !defined(CONFIG_ARCHES) */ -#define CONFIG_SYS_EBC_CFG 0xB8400000 /* EBC0_CFG */ +#define CONFIG_SYS_EBC_CFG 0xbfc00000 /* * Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO diff --git a/include/configs/cpu9260.h b/include/configs/cpu9260.h index de8cfb7..4ef8566 100644 --- a/include/configs/cpu9260.h +++ b/include/configs/cpu9260.h @@ -295,7 +295,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ /* NOR flash */ #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h new file mode 100644 index 0000000..432cd57 --- /dev/null +++ b/include/configs/da830evm.h @@ -0,0 +1,271 @@ +/* + * Copyright (C) 2008 Texas Instruments, Inc <www.ti.com> + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Board + */ + +/* + * SoC Configuration + */ +#define CONFIG_MACH_DAVINCI_DA830_EVM +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ +#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 /* memtest start addr */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024) /* 16MB test */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024) /* regular stack */ + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * I2C Configuration + */ +#define CONFIG_HARD_I2C +#define CONFIG_DRIVER_DAVINCI_I2C +#define CONFIG_SYS_I2C_SPEED 25000 /* 100Kbps won't work, H/W bug */ +#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ + +/* + * I2C EEPROM definitions for catalyst 24W256 EEPROM chip + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* + * Network & Ethernet Configuration + */ +#ifdef CONFIG_DRIVER_TI_EMAC +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#endif + +/* + * Flash & Environment + */ +#ifdef CONFIG_USE_NAND +#undef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_SYS_CLE_MASK 0x10 +#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 +#define DEF_BOOTM "" +#endif + +#ifdef CONFIG_USE_NOR +#define CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ +#define CONFIG_SYS_FLASH_SECT_SZ (64 << 10) /* 64KB */ +#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3) +#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE +#define PHYS_FLASH_SIZE (32 << 20) /* Flash size 32MB */ +#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) +#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ +#define CONFIG_SYS_FLASH_SPL_ACCESS +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#define CONFIG_ENV_OFFSET (256 << 10) +#define CONFIG_ENV_SECT_SIZE 4096 +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID) +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#endif + +/* + * USB configuration + */ +#define CONFIG_USB_DA8XX /* Platform hookup to MUSB controller */ +#define CONFIG_MUSB_HCD + +/* + * U-Boot general configuration + */ +#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */ +#undef CONFIG_MISC_INIT_R +#undef CONFIG_BOOTDELAY +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CONFIG_SYS_PROMPT "DA830-evm > " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS "mem=32M console=ttyS2,115200n8 root=/dev/mtdblock/2 rw noinitrd ip=dhcp" +#define CONFIG_BOOTCOMMAND "" +#define CONFIG_BOOTDELAY 3 + +/* + * U-Boot commands + */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#define CONFIG_CMD_EEPROM + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_PING +#endif + +#ifdef CONFIG_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_UBI +#define CONFIG_RBTREE +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SAVEENV +#endif + +#if !defined(CONFIG_USE_NAND) && \ + !defined(CONFIG_USE_NOR) && \ + !defined(CONFIG_USE_SPIFLASH) +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_ENV +#endif + +#ifdef CONFIG_USB_DA8XX + +#ifdef CONFIG_MUSB_HCD /* include support for usb host */ +#define CONFIG_CMD_USB /* include support for usb cmd */ + +#define CONFIG_USB_STORAGE /* MSC class support */ +#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */ +#define CONFIG_CMD_FAT /* inclue support for FAT/storage */ +#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */ + +#ifdef CONFIG_USB_KEYBOARD /* HID class support */ +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#endif /* CONFIG_USB_KEYBOARD */ + +#endif /* CONFIG_MUSB_HCD */ + +#ifdef CONFIG_MUSB_UDC +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "DA830EVM" +#endif /* CONFIG_MUSB_UDC */ + +#endif /* CONFIG_USB_DA8XX */ +#endif /* __CONFIG_H */ diff --git a/include/configs/davinci_dm355evm.h b/include/configs/davinci_dm355evm.h index ea40df0..37011c0 100644 --- a/include/configs/davinci_dm355evm.h +++ b/include/configs/davinci_dm355evm.h @@ -66,10 +66,10 @@ /* NAND: socketed, two chipselects, normally 2 GBytes */ #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #define CONFIG_SYS_NAND_USE_FLASH_BBT #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST #define CONFIG_SYS_NAND_PAGE_2K -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_SYS_NAND_LARGEPAGE #define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, } diff --git a/include/configs/davinci_dm355leopard.h b/include/configs/davinci_dm355leopard.h index 5db720e..e09fb75 100644 --- a/include/configs/davinci_dm355leopard.h +++ b/include/configs/davinci_dm355leopard.h @@ -65,6 +65,7 @@ /* NAND */ #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #define CONFIG_SYS_NAND_USE_FLASH_BBT #define CONFIG_SYS_NAND_HW_ECC @@ -114,7 +115,6 @@ #define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */ #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_OFFSET 0x3C0000 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_OVERWRITE #endif diff --git a/include/configs/davinci_dm365evm.h b/include/configs/davinci_dm365evm.h index 53a105b..c6e1d10 100644 --- a/include/configs/davinci_dm365evm.h +++ b/include/configs/davinci_dm365evm.h @@ -74,10 +74,10 @@ /* NAND: socketed, two chipselects, normally 2 GBytes */ #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #define CONFIG_SYS_NAND_USE_FLASH_BBT #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST #define CONFIG_SYS_NAND_PAGE_2K -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_SYS_NAND_LARGEPAGE #define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, } diff --git a/include/configs/davinci_dm6467evm.h b/include/configs/davinci_dm6467evm.h index 6617941..ddc5990 100644 --- a/include/configs/davinci_dm6467evm.h +++ b/include/configs/davinci_dm6467evm.h @@ -75,9 +75,9 @@ #define CONFIG_SYS_NO_FLASH #ifdef CONFIG_SYS_USE_NAND #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_IS_IN_NAND -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ #define CONFIG_SYS_NAND_BASE_LIST {0x42000000, } #define CONFIG_SYS_NAND_HW_ECC diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h index b045e80..5774df5 100644 --- a/include/configs/davinci_dvevm.h +++ b/include/configs/davinci_dvevm.h @@ -114,6 +114,7 @@ /*=====================*/ #ifdef CONFIG_SYS_USE_NAND #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_SYS_NO_FLASH #define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ @@ -138,7 +139,6 @@ #define CONFIG_SYS_NAND_HW_ECC #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define DEF_BOOTM "" #elif defined(CONFIG_SYS_USE_NOR) #ifdef CONFIG_NOR_UART_BOOT diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h index 9384cdd..3972ebc 100644 --- a/include/configs/davinci_schmoogie.h +++ b/include/configs/davinci_schmoogie.h @@ -83,6 +83,7 @@ #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_SYS_NO_FLASH #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ #define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */ #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ @@ -92,7 +93,6 @@ #define CONFIG_SYS_NAND_HW_ECC #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ /*=====================*/ /* Board related stuff */ /*=====================*/ diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h index 71d48fb..94be9dc 100644 --- a/include/configs/davinci_sffsdr.h +++ b/include/configs/davinci_sffsdr.h @@ -78,6 +78,7 @@ #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_SYS_NO_FLASH #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ #define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */ #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ @@ -87,7 +88,6 @@ #define CONFIG_SYS_NAND_HW_ECC #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ /* I2C switch definitions for PCA9543 chip */ #define CONFIG_SYS_I2C_PCA9543_ADDR 0x70 #define CONFIG_SYS_I2C_PCA9543_ADDR_LEN 0 /* Single register. */ diff --git a/include/configs/davinci_sonata.h b/include/configs/davinci_sonata.h index 9138b2b..490821a 100644 --- a/include/configs/davinci_sonata.h +++ b/include/configs/davinci_sonata.h @@ -114,6 +114,7 @@ /*=====================*/ #ifdef CONFIG_SYS_USE_NAND #define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_SYS_NO_FLASH #define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ @@ -125,7 +126,6 @@ #define CONFIG_SYS_NAND_HW_ECC #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define DEF_BOOTM "" #elif defined(CONFIG_SYS_USE_NOR) #ifdef CONFIG_NOR_UART_BOOT diff --git a/include/configs/delta.h b/include/configs/delta.h index 95e04f9..9c46c5b 100644 --- a/include/configs/delta.h +++ b/include/configs/delta.h @@ -226,8 +226,6 @@ #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE } #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* nand timeout values */ #define CONFIG_SYS_NAND_PROG_ERASE_TO 3000 #define CONFIG_SYS_NAND_OTHER_TO 100 diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index bd5037e..e81da67 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -66,6 +66,9 @@ /* Hardware drivers */ +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + /* DM9000 */ #define CONFIG_NET_MULTI 1 #define CONFIG_NET_RETRY_COUNT 20 @@ -129,8 +132,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" diff --git a/include/configs/eNET.h b/include/configs/eNET.h index 243a554..6a68bf4 100644 --- a/include/configs/eNET.h +++ b/include/configs/eNET.h @@ -28,6 +28,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_RELOC_FIXUP_WORKS + /* * Stuff still to be dealt with - */ @@ -61,7 +63,7 @@ /* * Size of malloc() pool */ -#define CONFIG_MALLOC_SIZE (CONFIG_SYS_ENV_SIZE + 128*1024) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) #define CONFIG_BAUDRATE 9600 @@ -234,8 +236,8 @@ #ifndef __ASSEMBLER__ extern unsigned long ip; -#define PRINTIP asm ("call next_line\n" \ - "next_line:\n" \ +#define PRINTIP asm ("call 0\n" \ + "0:\n" \ "pop %%eax\n" \ "movl %%eax, %0\n" \ :"=r"(ip) \ diff --git a/include/configs/gcplus.h b/include/configs/gcplus.h index 85db4f5..41294b9 100644 --- a/include/configs/gcplus.h +++ b/include/configs/gcplus.h @@ -66,7 +66,8 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_LAN91C96 /* we have an SMC9194 on-board */ +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 /* we have an SMC9194 on-board */ #define CONFIG_LAN91C96_BASE 0x100e0000 /* diff --git a/include/configs/imx27lite.h b/include/configs/imx27lite.h index 8ebb0bb..ee749ec 100644 --- a/include/configs/imx27lite.h +++ b/include/configs/imx27lite.h @@ -145,6 +145,7 @@ /* * MTD */ +#define CONFIG_FLASH_CFI_MTD #define CONFIG_MTD_DEVICE /* @@ -156,6 +157,7 @@ #define CONFIG_SYS_NAND_BASE 0xd8000000 #define CONFIG_JFFS2_NAND #define CONFIG_MXC_NAND_HWECC +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ /* * SD/MMC diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h new file mode 100644 index 0000000..d9028fa --- /dev/null +++ b/include/configs/ipek01.h @@ -0,0 +1,408 @@ +/* + * (C) Copyright 2006 + * MicroSys GmbH + * + * (C) Copyright 2009 + * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ + +#define CONFIG_MPC5200 +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPX5200 1 /* ... on MPX5200 board */ +#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ +#define CONFIG_IPEK01 /* Motherboard is ipek01 */ + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ + +#define CONFIG_MISC_INIT_R + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 9600 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +/* + * Video configuration for LIME GDC + */ +#define CONFIG_VIDEO +#ifdef CONFIG_VIDEO +#define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL +#define VIDEO_FB_16BPP_WORD_SWAP +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_CONSOLE_EXTRA_INFO +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_SPLASH_SCREEN +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ +/* Lime clock frequency */ +#define CONFIG_SYS_MB862xx_CCF 0x90000 /* geo 166MHz other 133MHz */ +/* SDRAM parameter */ +#define CONFIG_SYS_MB862xx_MMR 0x41c767e3 +#endif + +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 +#define CONFIG_PCI_SCAN_SHOW 1 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 + +#define CONFIG_NET_MULTI 1 +#define CONFIG_MII 1 +#define CONFIG_EEPRO100 1 +#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ + +/* Partitions */ +#define CONFIG_DOS_PARTITION + +/* USB */ +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_OHCI_BE_CONTROLLER +#define CONFIG_USB_STORAGE + +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP /* BMP support */ +#endif +#define CONFIG_CMD_DATE /* support for RTC, date/time...*/ +#define CONFIG_CMD_DHCP /* DHCP Support */ +#define CONFIG_CMD_FAT /* FAT support */ +#define CONFIG_CMD_I2C /* I2C serial bus support */ +#define CONFIG_CMD_IDE /* IDE harddisk support */ +#define CONFIG_CMD_IRQ /* irqinfo */ +#define CONFIG_CMD_MII /* MII support */ +#define CONFIG_CMD_PCI /* pciinfo */ +#define CONFIG_CMD_USB /* USB Support */ + +#define CONFIG_SYS_LOWBOOT 1 + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyPSC0\0" \ + "hostname=ipek01\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} " \ + "console=${consoledev},${baudrate}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr} - ${fdtaddr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdtaddr}\0" \ + "net_nfs=tftp 200000 ${bootfile}; tftp ${fdtaddr} ${fdtfile};" \ + "run nfsargs addip addtty;" \ + "bootm ${loadaddr} - ${fdtaddr}\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "bootfile=ipek01/uImage\0" \ + "load=tftp 100000 ipek01/u-boot.bin\0" \ + "update=protect off FC000000 +60000; era FC000000 +60000; " \ + "cp.b 100000 FC000000 ${filesize}\0" \ + "upd=run load;run update\0" \ + "fdtaddr=800000\0" \ + "loadaddr=400000\0" \ + "fdtfile=ipek01/ipek01.dtb\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* for 133MHz */ +/* PCI clock must be 33, because board will not boot */ +#undef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* for 66MHz */ + +/* + * Open firmware flat tree support + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ + +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* + * RTC configuration + */ +#define CONFIG_RTC_PCF8563 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 + +#define CONFIG_SYS_FLASH_BASE 0xFC000000 +#define CONFIG_SYS_FLASH_SIZE 0x01000000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ + CONFIG_SYS_MONITOR_LEN) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ + +/* use CFI flash driver */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_SRAM_BASE 0xF1000000 +#define CONFIG_SYS_SRAM_SIZE 0x00200000 +#define CONFIG_SYS_LIME_BASE 0xE4000000 +#define CONFIG_SYS_LIME_SIZE 0x04000000 +#define CONFIG_SYS_FPGA_BASE 0xC0000000 +#define CONFIG_SYS_FPGA_SIZE 0x10000000 +#define CONFIG_SYS_MPEG_BASE 0xe2000000 +#define CONFIG_SYS_MPEG_SIZE 0x01000000 +#define CONFIG_SYS_CF_BASE 0xe1000000 +#define CONFIG_SYS_CF_SIZE 0x01000000 + +/* Use SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +/* End of used area in DPRAM */ +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE + + + +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration + */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0x1d556624 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1...15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#if defined(CONFIG_MPC5200) +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE +#else +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL 0 +#endif + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE +#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_SRAM_SIZE +#define CONFIG_SYS_CS3_START CONFIG_SYS_LIME_BASE +#define CONFIG_SYS_CS3_SIZE CONFIG_SYS_LIME_SIZE +#define CONFIG_SYS_CS6_START CONFIG_SYS_FPGA_BASE +#define CONFIG_SYS_CS6_SIZE CONFIG_SYS_FPGA_SIZE +#define CONFIG_SYS_CS5_START CONFIG_SYS_CF_BASE +#define CONFIG_SYS_CS5_SIZE CONFIG_SYS_CF_SIZE +#define CONFIG_SYS_CS7_START CONFIG_SYS_MPEG_BASE +#define CONFIG_SYS_CS7_SIZE CONFIG_SYS_MPEG_SIZE + +#ifdef CONFIG_SYS_PCISPEED_66 +#define CONFIG_SYS_BOOTCS_CFG 0x0006F900 +#define CONFIG_SYS_CS1_CFG 0x0004FB00 +#define CONFIG_SYS_CS2_CFG 0x0006F900 +#else +#define CONFIG_SYS_BOOTCS_CFG 0x0002F900 +#define CONFIG_SYS_CS1_CFG 0x0001FB00 +#define CONFIG_SYS_CS2_CFG 0x0002F90C +#endif + +/* + * Ack active, Muxed mode, AS=24 bit address, DS=32 bit data, 0 + * waitstates, writeswap and readswap enabled + */ +#define CONFIG_SYS_CS3_CFG 0x00FFFB0C +#define CONFIG_SYS_CS6_CFG 0x00FFFB0C +#define CONFIG_SYS_CS7_CFG 0x4040751C + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33330000 + +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 + +/*----------------------------------------------------------------------- + * USB stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_USB_CLOCK 0x0001BBBB +#define CONFIG_USB_CONFIG 0x00005000 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ +#define CONFIG_IDE_PREINIT + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#endif /* __CONFIG_H */ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 3840267..c013ac4 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -140,6 +140,11 @@ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 +/* I2C bootstrap EEPROM */ +#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50 +#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 +#define CONFIG_4xx_CONFIG_BLOCKSIZE 8 + /* I2C RTC */ #define CONFIG_RTC_M41T11 1 #define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ @@ -194,8 +199,10 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_CHIP_CONFIG #define CONFIG_CMD_DATE +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP diff --git a/include/configs/keymile-common.h b/include/configs/keymile-common.h index 80c41a4..2ef6a35 100644 --- a/include/configs/keymile-common.h +++ b/include/configs/keymile-common.h @@ -127,8 +127,6 @@ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for UBI/UBIFS */ - /* UBI Support for all Keymile boards */ #define CONFIG_CMD_UBI #define CONFIG_RBTREE diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 965599c..8d4ce8d 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -217,8 +217,6 @@ #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) #define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index bec08da..b023326 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -72,6 +72,14 @@ #define CONFIG_SYS_IMMR 0xE0000000 /* + * Bus Arbitration Configuration Register (ACR) + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */ +#define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */ +#define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */ + +/* * DDR Setup */ #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ diff --git a/include/configs/korat.h b/include/configs/korat.h index ea6ba89..026dd08 100644 --- a/include/configs/korat.h +++ b/include/configs/korat.h @@ -69,6 +69,7 @@ #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE #define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE + 0x20000000) /* Don't change either of these */ #define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ @@ -359,6 +360,7 @@ /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT #define CONFIG_SYS_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ diff --git a/include/configs/lpd7a400-10.h b/include/configs/lpd7a400-10.h index 5f57c3a..91bf1fa 100644 --- a/include/configs/lpd7a400-10.h +++ b/include/configs/lpd7a400-10.h @@ -76,6 +76,5 @@ #define CONFIG_SMC91111 #define CONFIG_SMC91111_BASE (0x70000000) #undef CONFIG_SMC_USE_32_BIT -#define CONFIG_SMC_USE_IOFUNCS #endif /* __LPD7A400_10_H */ diff --git a/include/configs/lpd7a404-10.h b/include/configs/lpd7a404-10.h index 9074e28..b10e69d 100644 --- a/include/configs/lpd7a404-10.h +++ b/include/configs/lpd7a404-10.h @@ -76,6 +76,5 @@ #define CONFIG_SMC91111 #define CONFIG_SMC91111_BASE (0x70000000) #undef CONFIG_SMC_USE_32_BIT -#define CONFIG_SMC_USE_IOFUNCS #endif /* __LPD7A404_10_H */ diff --git a/include/configs/lpd7a404.h b/include/configs/lpd7a404.h index 102c0af..557f389 100644 --- a/include/configs/lpd7a404.h +++ b/include/configs/lpd7a404.h @@ -72,7 +72,7 @@ #include <config_cmd_default.h> #ifndef USE_920T_MMU - #define CONFIG_CMD_PING) + #define CONFIG_CMD_PING #undef CONFIG_CMD_CACHE #else #define CONFIG_CMD_DATE diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h index 43913ca..0a69210 100644 --- a/include/configs/lubbock.h +++ b/include/configs/lubbock.h @@ -58,7 +58,8 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x0C000000 /* diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 777a4d6..011dd5c 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -344,10 +344,12 @@ /* Video console */ #define CONFIG_VIDEO #define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL #define CONFIG_CFB_CONSOLE #define CONFIG_VIDEO_LOGO #define CONFIG_CONSOLE_EXTRA_INFO #define VIDEO_FB_16BPP_PIXEL_SWAP +#define VIDEO_FB_16BPP_WORD_SWAP #define CONFIG_VGA_AS_SINGLE_DEVICE #define CONFIG_VIDEO_SW_CURSOR @@ -495,8 +497,6 @@ /*----------------------------------------------------------------------- * Graphics (Fujitsu Lime) *----------------------------------------------------------------------*/ -/* SDRAM Clock frequency adjustment register */ -#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038 /* Lime Clock frequency is to set 100MHz */ #define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000 #if 0 @@ -504,15 +504,15 @@ #define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000 #endif -/* SDRAM Parameter register */ -#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC /* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars and pixel flare on display when 133MHz was configured. According to SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */ #ifdef CONFIG_SYS_LIME_CLOCK_133MHZ -#define CONFIG_SYS_LIME_MMR_VALUE 0x414FB7F3 +#define CONFIG_SYS_MB862xx_MMR 0x414FB7F3 +#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ #else -#define CONFIG_SYS_LIME_MMR_VALUE 0x414FB7F2 +#define CONFIG_SYS_MB862xx_MMR 0x414FB7F2 +#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ #endif /*----------------------------------------------------------------------- diff --git a/include/configs/manroland/common.h b/include/configs/manroland/common.h index c0122b7..c04830b 100644 --- a/include/configs/manroland/common.h +++ b/include/configs/manroland/common.h @@ -125,6 +125,9 @@ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_COMMAND_HISTORY 1 +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ /* Enable an alternate, more extensive memory test */ #define CONFIG_SYS_ALT_MEMTEST diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h index e194c8f..cccc31d 100644 --- a/include/configs/mecp5123.h +++ b/include/configs/mecp5123.h @@ -177,8 +177,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* * Configuration parameters for MPC5121 NAND driver */ diff --git a/include/configs/meesc.h b/include/configs/meesc.h index b996854..ab5cbca 100644 --- a/include/configs/meesc.h +++ b/include/configs/meesc.h @@ -121,7 +121,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA22 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Ethernet */ diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h index b486c77..9b1569a 100644 --- a/include/configs/microblaze-generic.h +++ b/include/configs/microblaze-generic.h @@ -146,7 +146,7 @@ #define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) /* stack */ -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_MALLOC_BASE /*#define RAMENV */ #define FLASH diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h index 8f71664..36488b3 100644 --- a/include/configs/mimc200.h +++ b/include/configs/mimc200.h @@ -74,7 +74,7 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTARGS \ - "root=/dev/mtdblock1 rootfstype=jffs2 console=ttyS1" + "root=/dev/mtdblock1 rootfstype=jffs2 fbmem=512k console=ttyS1" #define CONFIG_BOOTCOMMAND \ "fsload boot/uImage; bootm" diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h index ebc518c..fb49388 100644 --- a/include/configs/mpc5121ads.h +++ b/include/configs/mpc5121ads.h @@ -239,8 +239,6 @@ #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE #define CONFIG_SYS_NAND_SELECT_DEVICE /* driver supports mutipl. chips */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* * Configuration parameters for MPC5121 NAND driver */ diff --git a/include/configs/netstar.h b/include/configs/netstar.h index 7bddf24..20b423b 100644 --- a/include/configs/netstar.h +++ b/include/configs/netstar.h @@ -111,8 +111,6 @@ #define CONFIG_SYS_NAND_BASE 0x04000000 + (2 << 23) #define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_HARD_I2C #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_SYS_I2C_SLAVE 1 diff --git a/include/configs/nhk8815.h b/include/configs/nhk8815.h index a00c2fb..2b640dc 100644 --- a/include/configs/nhk8815.h +++ b/include/configs/nhk8815.h @@ -91,7 +91,6 @@ #define CONFIG_SYS_MEMTEST_END 0x0FFFFFFF #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256 * 1024) #define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */ -#define CONFIG_SYS_64BIT_VSPRINTF /* mtd desires this */ #define BOARD_LATE_INIT /* call board_late_init during start up */ diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h index 8408209..b0ebafd 100644 --- a/include/configs/omap1510inn.h +++ b/include/configs/omap1510inn.h @@ -60,7 +60,8 @@ #define CONFIG_SMC9196_BASE 0x08000300 #define CONFIG_SMC9196_EXT_PHY */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x08000300 #define CONFIG_LAN91C96_EXT_PHY diff --git a/include/configs/omap1610h2.h b/include/configs/omap1610h2.h index 42e0198..0bbb5b3 100644 --- a/include/configs/omap1610h2.h +++ b/include/configs/omap1610h2.h @@ -57,7 +57,8 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x04000300 #define CONFIG_LAN91C96_EXT_PHY diff --git a/include/configs/omap1610inn.h b/include/configs/omap1610inn.h index 22c873e..832dd42 100644 --- a/include/configs/omap1610inn.h +++ b/include/configs/omap1610inn.h @@ -58,7 +58,8 @@ */ /* */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x04000300 #define CONFIG_LAN91C96_EXT_PHY diff --git a/include/configs/omap2420h4.h b/include/configs/omap2420h4.h index 9c18842..47437b0 100644 --- a/include/configs/omap2420h4.h +++ b/include/configs/omap2420h4.h @@ -81,7 +81,8 @@ /* * SMC91c96 Etherent */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE (H4_CS1_BASE+0x300) #define CONFIG_LAN91C96_EXT_PHY @@ -163,14 +164,12 @@ /* * Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #ifdef CONFIG_APTIX -#define V_PROMPT "OMAP2420 Aptix # " +# define CONFIG_SYS_PROMPT "OMAP2420 Aptix # " #else -#define V_PROMPT "OMAP242x H4 # " +# define CONFIG_SYS_PROMPT "OMAP242x H4 # " #endif - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT V_PROMPT #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 19a5ec9..a8abb0e 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -97,6 +97,24 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "Beagle" + /* commands to include */ #include <config_cmd_default.h> @@ -148,8 +166,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" @@ -163,6 +179,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ + "usbtty=cdc_acm\0" \ "console=ttyS2,115200n8\0" \ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ @@ -213,12 +230,10 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "OMAP3 beagleboard.org # " - #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index a5514ae..a8d4105 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -101,6 +101,47 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + +/* USB + * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard + * Enable CONFIG_MUSB_UDD for Device functionalities. + */ +#define CONFIG_USB_OMAP3 1 +#define CONFIG_MUSB_HCD 1 +/* #define CONFIG_MUSB_UDC 1 */ + +#ifdef CONFIG_USB_OMAP3 + +#ifdef CONFIG_MUSB_HCD +#define CONFIG_CMD_USB + +#define CONFIG_USB_STORAGE +#define CONGIG_CMD_STORAGE +#define CONFIG_CMD_FAT + +#ifdef CONFIG_USB_KEYBOARD +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#endif /* CONFIG_USB_KEYBOARD */ + +#endif /* CONFIG_MUSB_HCD */ + +#ifdef CONFIG_MUSB_UDC +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "EVM" +#endif /* CONFIG_MUSB_UDC */ + +#endif /* CONFIG_USB_OMAP3 */ + /* commands to include */ #include <config_cmd_default.h> @@ -143,8 +184,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ /* NAND devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" @@ -159,6 +198,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ + "usbtty=cdc_acm\0" \ "console=ttyS2,115200n8\0" \ "mmcargs=setenv bootargs console=${console} " \ "root=/dev/mmcblk0p2 rw " \ @@ -194,12 +234,10 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "OMAP3_EVM # " - #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "OMAP3_EVM # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index ffb515d..c72fb9d 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -89,6 +89,9 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + /* commands to include */ #include <config_cmd_default.h> @@ -134,8 +137,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" @@ -199,12 +200,10 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "Overo # " - #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "Overo # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h index 6f21af3..f22fab5 100644 --- a/include/configs/omap3_pandora.h +++ b/include/configs/omap3_pandora.h @@ -92,6 +92,9 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + /* commands to include */ #include <config_cmd_default.h> @@ -137,9 +140,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ - -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" @@ -191,12 +191,10 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "Pandora # " - #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "Pandora # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h index 229dc5e..4d01933 100644 --- a/include/configs/omap3_sdp3430.h +++ b/include/configs/omap3_sdp3430.h @@ -137,6 +137,9 @@ #define CONFIG_SYS_I2C_BUS_SELECT 1 #define CONFIG_DRIVER_OMAP34XX_I2C 1 +/* DDR - I use Infineon DDR */ +#define CONFIG_OMAP3_INFINEON_DDR 1 + /* OMITTED: single 1 Gbit MT29F1G NAND flash */ /* @@ -200,7 +203,8 @@ */ #if defined(CONFIG_CMD_NET) -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE DEBUG_BASE #define CONFIG_LAN91C96_EXT_PHY @@ -263,12 +267,11 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "OMAP34XX SDP # " #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "OMAP34XX SDP # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index da4b677..cdf95c0 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -98,6 +98,24 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "Zoom1" + /* commands to include */ #include <config_cmd_default.h> @@ -144,9 +162,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ - -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" @@ -160,6 +175,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ + "usbtty=cdc_acm\0" \ "console=ttyS2,115200n8\0" \ "videomode=1024x768@60,vxres=1024,vyres=768\0" \ "videospec=omapfb:vram:2M,vram:4M\0" \ @@ -199,12 +215,10 @@ /* * Miscellaneous configurable options */ -#define V_PROMPT "OMAP3 Zoom1# " - #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_PROMPT "OMAP3 Zoom1 # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h index 32cd6fd..7a8beb8 100644 --- a/include/configs/omap3_zoom2.h +++ b/include/configs/omap3_zoom2.h @@ -98,6 +98,9 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + /* Status LED */ #define CONFIG_STATUS_LED 1 /* Status LED enabled */ #define CONFIG_BOARD_SPECIFIC_LED 1 @@ -122,6 +125,20 @@ #define CONFIG_OMAP3_GPIO_3 /* board revision */ #define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */ +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "Zoom2" + /* commands to include */ #include <config_cmd_default.h> @@ -164,11 +181,12 @@ #define GPMC_NAND_ECC_LP_x16_LAYOUT 1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* Environment information */ #define CONFIG_BOOTDELAY 10 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "usbtty=cdc_acm\0" \ + /* * Miscellaneous configurable options */ diff --git a/include/configs/omap5912osk.h b/include/configs/omap5912osk.h index d0ce9dc..bc660e3 100644 --- a/include/configs/omap5912osk.h +++ b/include/configs/omap5912osk.h @@ -61,7 +61,8 @@ */ /* */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x04800300 #define CONFIG_LAN91C96_EXT_PHY diff --git a/include/configs/omap730p2.h b/include/configs/omap730p2.h index 32a9b23..a6a8a02 100644 --- a/include/configs/omap730p2.h +++ b/include/configs/omap730p2.h @@ -65,7 +65,8 @@ * Hardware drivers */ -#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_NET_MULTI +#define CONFIG_LAN91C96 #define CONFIG_LAN91C96_BASE 0x04000300 #define CONFIG_LAN91C96_EXT_PHY diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index 2aba0cb..88f27ba 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -114,7 +114,6 @@ #define NAND_MAX_CHIPS 1 #define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ #define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* diff --git a/include/configs/pdnb3.h b/include/configs/pdnb3.h index 2612165..220f686 100644 --- a/include/configs/pdnb3.h +++ b/include/configs/pdnb3.h @@ -266,7 +266,6 @@ */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x51000000 /* NAND FLASH Base Address */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* diff --git a/include/configs/pleb2.h b/include/configs/pleb2.h index 635ef71..9e69411 100644 --- a/include/configs/pleb2.h +++ b/include/configs/pleb2.h @@ -56,8 +56,10 @@ */ /* None - PLEB 2 doesn't have any of this. - #define CONFIG_DRIVER_LAN91C96 - #define CONFIG_LAN91C96_BASE 0x0C000000 */ + #define CONFIG_NET_MULTI + #define CONFIG_LAN91C96 + #define CONFIG_LAN91C96_BASE 0x0C000000 + */ /* * select serial console configuration diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h index 9bf49ba..399d15f 100644 --- a/include/configs/pm9261.h +++ b/include/configs/pm9261.h @@ -236,9 +236,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA16 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - - /* NOR flash */ #define CONFIG_SYS_FLASH_CFI 1 #define CONFIG_FLASH_CFI_DRIVER 1 diff --git a/include/configs/pm9263.h b/include/configs/pm9263.h index 6761c18..0af1280 100644 --- a/include/configs/pm9263.h +++ b/include/configs/pm9263.h @@ -259,7 +259,6 @@ #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PB30 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif #define CONFIG_CMD_JFFS2 1 diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h index d63c43e..b08dcd4 100644 --- a/include/configs/quad100hd.h +++ b/include/configs/quad100hd.h @@ -226,7 +226,6 @@ #define CONFIG_SYS_NAND_ALE 30 /* our ALE is GPIO30 */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /*----------------------------------------------------------------------- diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h index 3f4d42c..3d8e25c 100644 --- a/include/configs/rd6281a.h +++ b/include/configs/rd6281a.h @@ -107,7 +107,6 @@ #define NAND_MAX_CHIPS 1 #define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ #define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* diff --git a/include/configs/sbc35_a9g20.h b/include/configs/sbc35_a9g20.h index 7a2dcd8..f4b3477 100644 --- a/include/configs/sbc35_a9g20.h +++ b/include/configs/sbc35_a9g20.h @@ -161,7 +161,6 @@ #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif #define CONFIG_BOOTCOMMAND "nboot 0x21000000 0 400000" diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 682d241..315eebe 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -285,9 +285,6 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - /* * I2C */ diff --git a/include/configs/sc3.h b/include/configs/sc3.h index 5763760..a5eca39 100644 --- a/include/configs/sc3.h +++ b/include/configs/sc3.h @@ -376,11 +376,6 @@ * CONFIG_SYS_FLASH_BASE -> start address of internal flash * CONFIG_SYS_MONITOR_BASE -> start of u-boot */ -#ifndef __ASSEMBLER__ -extern unsigned long offsetOfBigFlash; -extern unsigned long offsetOfEnvironment; -#endif - #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFFE00000 #define CONFIG_SYS_MONITOR_BASE 0xFFFC0000 /* placed last 256k */ @@ -427,8 +422,6 @@ extern unsigned long offsetOfEnvironment; #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x77D00000 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - #define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ /* No command line, one static partition */ diff --git a/include/configs/sc520_cdp.h b/include/configs/sc520_cdp.h index 214a9af..2f1dae7 100644 --- a/include/configs/sc520_cdp.h +++ b/include/configs/sc520_cdp.h @@ -65,7 +65,7 @@ /* * Size of malloc() pool */ -#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) #define CONFIG_BAUDRATE 9600 diff --git a/include/configs/sc520_spunk.h b/include/configs/sc520_spunk.h index f3fc960..cf5633c 100644 --- a/include/configs/sc520_spunk.h +++ b/include/configs/sc520_spunk.h @@ -63,7 +63,7 @@ /* * Size of malloc() pool */ -#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) #define CONFIG_BAUDRATE 9600 diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 9605ce2..568d9fc 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -282,8 +282,20 @@ /* USB */ #ifdef CONFIG_440EPX + +#undef CONFIG_USB_EHCI /* OHCI by default */ + +#ifdef CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_PPC4XX +#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_EHCI_MMIO_BIG_ENDIAN +#define CONFIG_EHCI_DESC_BIG_ENDIAN +#ifdef CONFIG_4xx_DCACHE +#define CONFIG_EHCI_DCACHE +#endif +#else /* CONFIG_USB_EHCI */ #define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE #define CONFIG_SYS_OHCI_BE_CONTROLLER #undef CONFIG_SYS_USB_OHCI_BOARD_INIT @@ -291,7 +303,9 @@ #define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#endif +#define CONFIG_USB_STORAGE /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE @@ -364,6 +378,7 @@ /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT #define CONFIG_SYS_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index 1f95a3c..fc401a8 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -107,7 +107,6 @@ #define NAND_MAX_CHIPS 1 #define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ #define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* diff --git a/include/configs/smdk6400.h b/include/configs/smdk6400.h index f644cd2..f04feae 100644 --- a/include/configs/smdk6400.h +++ b/include/configs/smdk6400.h @@ -268,8 +268,6 @@ 48, 49, 50, 51, 52, 53, 54, 55, \ 56, 57, 58, 59, 60, 61, 62, 63} -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* Boot configuration (define only one of next 3) */ #define CONFIG_BOOT_NAND /* None of these are currently implemented. Left from the original Samsung diff --git a/include/configs/smdkc100.h b/include/configs/smdkc100.h index 9c27079..a8ba052 100644 --- a/include/configs/smdkc100.h +++ b/include/configs/smdkc100.h @@ -211,8 +211,6 @@ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* 256 KiB */ #define CONFIG_IDENT_STRING " for SMDKC100" -#define CONFIG_SYS_64BIT_VSPRINTF - #if !defined(CONFIG_NAND_SPL) && (TEXT_BASE >= 0xc0000000) #define CONFIG_ENABLE_MMU #endif diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 35feed0..9641041 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -188,8 +188,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_CMD_NAND -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* LIME GDC */ #define CONFIG_SYS_LIME_BASE 0xc8000000 #define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ @@ -198,11 +196,13 @@ #define CONFIG_VIDEO #define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL #define CONFIG_CFB_CONSOLE #define CONFIG_VIDEO_LOGO #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_CONSOLE_EXTRA_INFO #define VIDEO_FB_16BPP_PIXEL_SWAP +#define VIDEO_FB_16BPP_WORD_SWAP #define CONFIG_VGA_AS_SINGLE_DEVICE #define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_VIDEO_SW_CURSOR @@ -210,6 +210,11 @@ #define CONFIG_VIDEO_BMP_GZIP #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ +/* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */ +#define CONFIG_SYS_MB862xx_CCF 0x10000 +/* SDRAM parameter */ +#define CONFIG_SYS_MB862xx_MMR 0x4157BA63 + /* Serial Port */ #define CONFIG_CONS_INDEX 1 diff --git a/include/configs/tny_a9260.h b/include/configs/tny_a9260.h index 5b70a7b..4ad081b 100644 --- a/include/configs/tny_a9260.h +++ b/include/configs/tny_a9260.h @@ -138,7 +138,6 @@ #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif #define CONFIG_BOOTCOMMAND "nboot 0x21000000 0 400000" diff --git a/include/configs/vct.h b/include/configs/vct.h index 20bf481..1b894a6 100644 --- a/include/configs/vct.h +++ b/include/configs/vct.h @@ -284,12 +284,6 @@ int vct_gpio_get(int pin); #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ /* - * Needed for 64bit printf format - */ -#define CONFIG_SYS_64BIT_VSPRINTF 1 -#define CONFIG_SYS_64BIT_STRTOUL 1 - -/* * UBI configuration */ #if defined(CONFIG_VCT_ONENAND) diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h index f9db73b..dbc15b2 100644 --- a/include/configs/vme8349.h +++ b/include/configs/vme8349.h @@ -35,6 +35,13 @@ #define __CONFIG_H /* + * Top level Makefile configuration choices + */ +#ifdef CONFIG_MK_caddy2 +#define VME_CADDY2 +#endif + +/* * High Level Configuration Options */ #define CONFIG_E300 1 /* E300 Family */ @@ -43,6 +50,8 @@ #define CONFIG_MPC8349 1 /* MPC8349 specific */ #define CONFIG_VME8349 1 /* ESD VME8349 board specific */ +#define CONFIG_MISC_INIT_R + #define CONFIG_PCI /* Don't enable PCI2 on vme834x - it doesn't exist physically. */ #undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ @@ -75,7 +84,9 @@ */ #define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ -#undef CONFIG_SPD_EEPROM /* dont use SPD EEPROM for DDR setup*/ +#define CONFIG_SPD_EEPROM +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_SYS_READ_SPD vme8349_read_spd #define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */ /* @@ -96,54 +107,40 @@ #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) #define CONFIG_DDR_2T_TIMING - -/* - * Manually set up DDR parameters - */ -#define CONFIG_SYS_DDR_SIZE 512 /* MB */ - -#if (CONFIG_SYS_DDR_SIZE == 512) -#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10 | \ - CSCONFIG_BANK_BIT_3) -#endif - -/* - * Manually set up DDR parameters - */ -#define CONFIG_SYS_DDR_TIMING_0 0x00220802 -#define CONFIG_SYS_DDR_TIMING_1 0x39377322 -#define CONFIG_SYS_DDR_TIMING_2 0x2f9848ca /* P9-45, tuning? */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuf,no DYN_PWR */ -#define CONFIG_SYS_DDR_MODE 0x07940242 -#define CONFIG_SYS_DDR_MODE2 0x00000000 -/* autocharge,no open page */ -#define CONFIG_SYS_DDR_INTERVAL 0x04060100 -#define CONFIG_SYS_DDR_SDRAM_CFG 0x63000000 -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x04061000 +#define CONFIG_SYS_DDRCDR 0x80080001 /* * FLASH on the Local Bus */ #define CONFIG_SYS_FLASH_CFI #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */ -/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ +#ifdef VME_CADDY2 +#define CONFIG_SYS_FLASH_BASE 0xffc00000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 4 /* flash size in MB */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + (2 << BR_PS_SHIFT) | /* 32bit */ \ + BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM 0xffc06ff7 /* 4 MB flash size */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000015 /* 4 MB window size */ +#else +#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */ #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ (2 << BR_PS_SHIFT) | /* 32bit */ \ BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM 0xF8006FF7 /* 128 MB flash size */ +#define CONFIG_SYS_OR0_PRELIM 0xf8006ff7 /* 128 MB flash size */ #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001A /* 128 MB window size */ +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001a /* 128 MB window size */ +#endif +/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ #define CONFIG_SYS_BR1_PRELIM (0xf0000000 | 0x00001801) -#define CONFIG_SYS_OR1_PRELIM (0xffff8000 | 0x00000200) +#define CONFIG_SYS_OR1_PRELIM (0xfffc0008 | 0x00000200) #define CONFIG_SYS_LBLAWBAR1_PRELIM 0xf0000000 -#define CONFIG_SYS_LBLAWAR1_PRELIM (0x80000000 | 0x0000000e) +#define CONFIG_SYS_LBLAWAR1_PRELIM (0x80000000 | 0x00000011) #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/ @@ -157,7 +154,7 @@ #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_RAMBOOT #else -#undef CONFIG_SYS_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif #define CONFIG_SYS_INIT_RAM_LOCK 1 @@ -174,11 +171,10 @@ /* * Local Bus LCRR and LBCR regs - * LCRR: DLL bypass, Clock divider is 4 + * LCRR: no DLL bypass, Clock divider is 4 * External Local Bus rate is * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 #define CONFIG_SYS_LBC_LBCR 0x00000000 @@ -268,10 +264,10 @@ #undef PCI_ONE_PCI1 #endif -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - +#ifndef VME_CADDY2 #define CONFIG_NET_MULTI +#endif +#define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_TULIP @@ -282,19 +278,26 @@ #define PCI_IDSEL_NUMBER 0xFIXME #endif +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + #endif /* CONFIG_PCI */ /* * TSEC configuration */ +#ifdef VME_CADDY2 +#define CONFIG_E1000 +#else #define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#endif #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI #endif -#define CONFIG_GMII /* MII PHY management */ +#define CONFIG_GMII /* MII PHY management */ #define CONFIG_TSEC1 #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 @@ -312,6 +315,12 @@ #endif /* CONFIG_TSEC_ENET */ +#if defined(CONFIG_E1000) +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI +#endif +#endif + /* * Environment */ @@ -560,7 +569,7 @@ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* boot command will set bootargs */ -#define CONFIG_BAUDRATE 115200 +#define CONFIG_BAUDRATE 9600 #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ @@ -605,4 +614,9 @@ #define CONFIG_BOOTCOMMAND "run flash_self" +#ifndef __ASSEMBLY__ +int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen, + unsigned char *buffer, int len); +#endif + #endif /* __CONFIG_H */ diff --git a/include/configs/yucca.h b/include/configs/yucca.h index b165bd7..42f8807 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -389,6 +389,11 @@ #define FPGA_REG1A_PE_SELSOURCE_0 0x0002 #define FPGA_REG1A_PE_SELSOURCE_1 0x0001 +#define FPGA_REG1A_GLED_ENCODE(n) (FPGA_REG1A_PE0_GLED >> (n)) +#define FPGA_REG1A_YLED_ENCODE(n) (FPGA_REG1A_PE0_YLED >> (n)) +#define FPGA_REG1A_PWRON_ENCODE(n) (FPGA_REG1A_PE0_PWRON >> (n)) +#define FPGA_REG1A_REFCLK_ENCODE(n) (FPGA_REG1A_PE0_REFCLK_ENABLE >> (n)) + /*----------------------------------------------------------------------------+ | PCIe Miscellaneous +----------------------------------------------------------------------------*/ @@ -407,6 +412,9 @@ #define FPGA_REG1C_PE1_PERST 0x0008 #define FPGA_REG1C_PE2_PERST 0x0004 +#define FPGA_REG1C_ROOTPOINT_ENCODE(n) (FPGA_REG1C_PE0_ROOTPOINT >> (n)) +#define FPGA_REG1C_PERST_ENCODE(n) (FPGA_REG1C_PE0_PERST >> (n)) + /*----------------------------------------------------------------------------+ | Defines +----------------------------------------------------------------------------*/ diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h index 36c341e..d0fc138 100644 --- a/include/configs/zylonite.h +++ b/include/configs/zylonite.h @@ -205,8 +205,6 @@ #define CONFIG_SYS_NAND_SENDCMD_RETRY 3 #undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */ -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ - /* NAND Timing Parameters (in ns) */ #define NAND_TIMING_tCH 10 #define NAND_TIMING_tCS 0 |