summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/MPC8260ADS.h41
-rw-r--r--include/configs/VCMA9.h75
-rw-r--r--include/configs/smdk2400.h8
-rw-r--r--include/configs/smdk2410.h23
-rw-r--r--include/configs/trab.h5
5 files changed, 130 insertions, 22 deletions
diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
index 30b7207..dc2c313 100644
--- a/include/configs/MPC8260ADS.h
+++ b/include/configs/MPC8260ADS.h
@@ -26,10 +26,6 @@
* MA 02111-1307 USA
*/
-/*
- * Config header file for a MPC8260ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
- */
-
#ifndef __CONFIG_H
#define __CONFIG_H
@@ -77,23 +73,45 @@
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-#if (CONFIG_ETHER_INDEX == 2)
+#ifdef CONFIG_ETHER_ON_FCC
+#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
+
+#if (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
* - Tx-CLK is CLK14
* - Select bus for bd/buffers (see 28-13)
- * - Half duplex
+ * - Full duplex
*/
# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#endif /* CONFIG_ETHER_INDEX */
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+/*
+ * GPIO pins used for bit-banged MII communications
+ */
+#define MDIO_PORT 2 /* Port C */
+#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
+#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
+#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
+
+#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
+ else iop->pdat &= ~0x00400000
+
+#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
+ else iop->pdat &= ~0x00200000
+
+#define MIIDELAY udelay(1)
+
+#endif /* CONFIG_ETHER_ON_FCC */
+
/* other options */
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
@@ -172,9 +190,6 @@
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
- /* for versions < 2.4.5-pre5 */
-
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
@@ -239,8 +254,8 @@
#ifndef CFG_RAMBOOT
# define CFG_ENV_IS_IN_FLASH 1
-# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-# define CFG_ENV_SECT_SIZE 0x40000
+# define CFG_ENV_SECT_SIZE 0x40000
+# define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_ENV_SECT_SIZE)
#else
# define CFG_ENV_IS_IN_NVRAM 1
# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
index a73281c..c0103fc 100644
--- a/include/configs/VCMA9.h
+++ b/include/configs/VCMA9.h
@@ -59,9 +59,13 @@
#define CONFIG_COMMANDS \
(CONFIG_CMD_DFL | \
CFG_CMD_CACHE | \
+ /*CFG_CMD_JFFS2 |*/ \
+ /*CFG_CMD_NAND |*/ \
CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
+ /*CFG_CMD_USB |*/ \
CFG_CMD_REGINFO | \
+ CFG_CMD_DATE | \
CFG_CMD_ELF | \
CFG_CMD_BSP)
@@ -111,6 +115,24 @@
*/
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on VCMA9 */
+/************************************************************
+ * USB support
+ ************************************************************/
+#if 0
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_USB_STORAGE
+
+/* Enable needed helper functions */
+#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
+#endif
+
+/************************************************************
+ * RTC
+ ************************************************************/
+#define CONFIG_RTC_S3C24X0 1
+
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
@@ -138,7 +160,7 @@
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x30000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
+#define CFG_MEMTEST_END 0x33F80000 /* 63.5 MB in DRAM */
#define CFG_ALT_MEMTEST
#define CFG_LOAD_ADDR 0x33000000 /* default load address */
@@ -152,6 +174,13 @@
/* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+/************************************************************
+ * Ident
+ ************************************************************/
+/*#define VERSION_TAG "released"*/
+#define VERSION_TAG "unstable"
+#define CONFIG_IDENT_STRING "\n(c) 2003 by MPL AG Switzerland, MEV-10080-001 " VERSION_TAG
+
/*-----------------------------------------------------------------------
* Stack sizes
*
@@ -204,6 +233,48 @@
#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
#endif
-#define MULTI_PURPOSE_SOCKET_ADDR 0
+
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+
+#define MULTI_PURPOSE_SOCKET_ADDR 0x08000000
+
+/*-----------------------------------------------------------------------
+ * NAND flash settings
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define NAND_WAIT_READY(nand) NF_WaitRB()
+
+#define NAND_DISABLE_CE(nand) NF_SetCE(NFCE_HIGH)
+#define NAND_ENABLE_CE(nand) NF_SetCE(NFCE_LOW)
+
+
+#define WRITE_NAND_COMMAND(d, adr) NF_Cmd(d)
+#define WRITE_NAND_COMMANDW(d, adr) NF_CmdW(d)
+#define WRITE_NAND_ADDRESS(d, adr) NF_Addr(d)
+#define WRITE_NAND(d, adr) NF_Write(d)
+#define READ_NAND(adr) NF_Read()
+/* the following functions are NOP's because S3C24X0 handles this in hardware */
+#define NAND_CTL_CLRALE(nandptr)
+#define NAND_CTL_SETALE(nandptr)
+#define NAND_CTL_CLRCLE(nandptr)
+#define NAND_CTL_SETCLE(nandptr)
+
+#define CONFIG_MTD_NAND_VERIFY_WRITE 1
+#define CONFIG_MTD_NAND_ECC_JFFS2 1
+
+#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */
#endif /* __CONFIG_H */
diff --git a/include/configs/smdk2400.h b/include/configs/smdk2400.h
index d0ad65e..a557bc6 100644
--- a/include/configs/smdk2400.h
+++ b/include/configs/smdk2400.h
@@ -86,10 +86,14 @@
#define CONFIG_TIMESTAMP 1 /* Print timestamp info for images */
+/* Use s3c2400's RTC */
+#define CONFIG_RTC_S3C24X0 1
+
#ifndef USE_920T_MMU
-#define CONFIG_COMMANDS_tmp (CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
+#define CONFIG_COMMANDS_tmp ((CONFIG_CMD_DFL & ~CFG_CMD_CACHE) | \
+ CFG_CMD_DATE)
#else
-#define CONFIG_COMMANDS_tmp (CONFIG_CMD_DFL)
+#define CONFIG_COMMANDS_tmp (CONFIG_CMD_DFL | CFG_CMD_DATE)
#endif
#ifdef CONFIG_HWFLOW
diff --git a/include/configs/smdk2410.h b/include/configs/smdk2410.h
index 65dd3fe..0dcbbb0 100644
--- a/include/configs/smdk2410.h
+++ b/include/configs/smdk2410.h
@@ -67,16 +67,29 @@
*/
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SMDK2410 */
+/************************************************************
+ * RTC
+ ************************************************************/
+#define CONFIG_RTC_S3C24X0 1
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
-#ifndef USE_920T_MMU
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
-#endif
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+#define CONFIG_COMMANDS \
+ (CONFIG_CMD_DFL | \
+ CFG_CMD_CACHE | \
+ /*CFG_CMD_NAND |*/ \
+ /*CFG_CMD_EEPROM |*/ \
+ /*CFG_CMD_I2C |*/ \
+ /*CFG_CMD_USB |*/ \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_DATE | \
+ CFG_CMD_ELF)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
diff --git a/include/configs/trab.h b/include/configs/trab.h
index 2466189..15b6b19 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -90,6 +90,9 @@
#define CONFIG_TIMESTAMP 1 /* Print timestamp info for images */
+/* Use s3c2400's RTC */
+#define CONFIG_RTC_S3C24X0 1
+
#ifdef CONFIG_HWFLOW
#define CONFIG_COMMANDS_ADD_HWFLOW CFG_CMD_HWFLOW
#else
@@ -105,11 +108,13 @@
#ifndef USE_920T_MMU
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL & ~CFG_CMD_CACHE) | \
CFG_CMD_BSP | \
+ CFG_CMD_DATE | \
CONFIG_COMMANDS_ADD_HWFLOW | \
CONFIG_COMMANDS_ADD_VFD )
#else
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_BSP | \
+ CFG_CMD_DATE | \
CONFIG_COMMANDS_ADD_HWFLOW | \
CONFIG_COMMANDS_ADD_VFD )
#endif