summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/bf533-ezkit.h228
-rw-r--r--include/configs/bf533-stamp.h467
-rw-r--r--include/configs/bf537-stamp.h502
-rw-r--r--include/configs/bf561-ezkit.h244
-rw-r--r--include/configs/ezkit533.h188
-rw-r--r--include/configs/stamp.h333
6 files changed, 1441 insertions, 521 deletions
diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h
new file mode 100644
index 0000000..65dfc81
--- /dev/null
+++ b/include/configs/bf533-ezkit.h
@@ -0,0 +1,228 @@
+/*
+ * U-boot - Configuration file for BF533 EZKIT board
+ */
+
+#ifndef __CONFIG_EZKIT533_H__
+#define __CONFIG_EZKIT533_H__
+
+#define CONFIG_BAUDRATE 57600
+#define CONFIG_STAMP 1
+
+#define CONFIG_BOOTDELAY 5
+#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+
+#define CFG_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_LOADADDR 0x01000000 /* default load address */
+#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
+/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
+
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20310300
+
+#if 0
+#define CONFIG_MII
+#define CFG_DISCOVER_PHY
+#endif
+
+#define CONFIG_RTC_BFIN 1
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
+
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
+/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF531 0x31
+#define ADSP_BF532 0x32
+#define ADSP_BF533 0x33
+#define BFIN_CPU ADSP_BF533
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 27000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 22
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
+#define CONFIG_SPI_BAUD_INITBLOCK 4
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#endif
+
+#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC16M16A2TG_75 1
+
+#define CONFIG_LOADS_ECHO 1
+
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_PING | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_DATE)
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
+#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
+#define CFG_LOAD_ADDR 0x01000000 /* default load address */
+#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
+#define CFG_FLASH_BASE 0x20000000
+
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_SIZE 0x4000
+#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
+
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_FLASH0_BASE 0x20000000
+#define CFG_FLASH1_BASE 0x20200000
+#define CFG_FLASH2_BASE 0x20280000
+#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20020000
+#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
+
+/* JFFS Partition offset set */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR 11
+
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+
+#define POLL_MODE 1
+#define FLASH_TOT_SECT 40
+#define FLASH_SIZE 0x220000
+#define CFG_FLASH_SIZE 0x220000
+
+/*
+ * Initialize PSD4256 registers for using I2C
+ */
+#define CONFIG_MISC_INIT_R
+
+/*
+ * I2C settings
+ * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
+ */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL PF0
+#define PF_SDA PF1
+
+#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
+#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SDA; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SDA; \
+ asm("ssync;"); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SCL; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SCL; \
+ asm("ssync;"); \
+ }
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
+
+#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+
+/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
+/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
+ ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
+#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
+ B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
+*/
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0x7BB07BB0
+#define AMBCTL1VAL 0xFFC27BB0
+
+#define CONFIG_VDSP 1
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP 0x8
+#define SHT_STRTAB_VDSP 0x1
+#define ELFSHDRSIZE_VDSP 0x2C
+#define VDSP_ENTRY_ADDR 0xFFA00000
+#endif
+
+#endif
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
new file mode 100644
index 0000000..79a1404
--- /dev/null
+++ b/include/configs/bf533-stamp.h
@@ -0,0 +1,467 @@
+/*
+ * U-boot - Configuration file for BF533 STAMP board
+ */
+
+#ifndef __CONFIG_STAMP_H__
+#define __CONFIG_STAMP_H__
+
+#define CONFIG_STAMP 1
+#define CONFIG_RTC_BFIN 1
+#define CONFIG_BF533 1
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
+/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF531 0x31
+#define ADSP_BF532 0x32
+#define ADSP_BF533 0x33
+#define BFIN_CPU ADSP_BF533
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/*
+ * Stringize definitions - needed for environmental settings
+ */
+#define STRINGIZE2(x) #x
+#define STRINGIZE(x) STRINGIZE2(x)
+
+/*
+ * Board settings
+ */
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
+
+/* FLASH/ETHERNET uses the same address range */
+#define SHARED_RESOURCES 1
+
+/* Is I2C bit-banged? */
+#define CONFIG_SOFT_I2C 1
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL PF3
+#define PF_SDA PF2
+
+/*
+ * Video splash screen support
+ */
+#define CONFIG_VIDEO 0
+
+#define CONFIG_VDSP 1
+
+/*
+ * Clock settings
+ */
+
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 11059200
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 36
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_SPI_BAUD_INITBLOCK 4
+#endif
+
+/*
+ * Network settings
+ */
+
+#if (CONFIG_DRIVER_SMC91111)
+#if 0
+#define CONFIG_MII
+#endif
+
+/* network support */
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME STAMP
+#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
+
+/* To remove hardcoding and enable MAC storage in EEPROM */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+#endif /* CONFIG_DRIVER_SMC91111 */
+
+/*
+ * Flash settings
+ */
+
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_FLASH_CFI_AMD_RESET
+
+#define CFG_FLASH_BASE 0x20000000
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20004000
+#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_ENV_OFFSET 0x4000
+#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
+#endif
+
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
+#define ENV_IS_EMBEDDED
+
+#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
+#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
+
+/* JFFS Partition offset set */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR 11
+
+/*
+ * following timeouts shall be used once the
+ * Flash real protection is enabled
+ */
+#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
+#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
+
+/*
+ * SDRAM settings & memory map
+ */
+
+#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#endif
+
+#define CFG_SDRAM_BASE 0x00000000
+
+#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
+#define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1)
+#define CONFIG_LOADADDR 0x01000000
+
+#define CFG_LOAD_ADDR CONFIG_LOADADDR
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+
+#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000)
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
+
+/* Check to make sure everything fits in SDRAM */
+#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE)
+ #error Memory Map does not fit into configuration
+#endif
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#endif
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
+#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
+#else
+#undef CONFIG_SPI_FLASH_FAST_READ
+#endif
+#endif
+
+/*
+ * Command settings
+ */
+
+#define CFG_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+#endif
+
+/* configuration lookup from the BOOTP/DHCP server, */
+/* but not try to load any image using TFTP */
+
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CONFIG_BOOTCOMMAND "run ramboot"
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
+
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_PING | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE)
+
+#else
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE)
+#endif
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+ "$(rootpath) console=ttyBF0,57600\0" \
+ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux; " \
+ "run ramargs;run addip;bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux; " \
+ "run nfsargs;run addip;bootelf\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.bin; " \
+ "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
+ "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
+ ""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "
+#endif
+
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+ "$(rootpath) console=ttyBF0,57600\0" \
+ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux; " \
+ "run ramargs;run addip;bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux; " \
+ "run nfsargs;run addip;bootelf\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.ldr;" \
+ "eeprom write $(loadaddr) 0x0 $(filesize);\0"\
+ ""
+#endif
+
+#ifdef CONFIG_SOFT_I2C
+#if (!CONFIG_SOFT_I2C)
+#undef CONFIG_SOFT_I2C
+#endif
+#endif
+
+#if (CONFIG_SOFT_I2C)
+#define CONFIG_COMMANDS2 CFG_CMD_I2C
+#else
+#define CONFIG_COMMANDS2 0
+#endif /* CONFIG_SOFT_I2C */
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 | CFG_CMD_DHCP)
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2)
+#endif
+
+/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Console settings
+ */
+
+#define CONFIG_BAUDRATE 57600
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (BFIN_CPU == ADSP_BF531)
+#define CFG_PROMPT "serial_bf531> " /* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF532)
+#define CFG_PROMPT "serial_bf532> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "serial_bf533> " /* Monitor Command Prompt */
+#endif
+#else
+#if (BFIN_CPU == ADSP_BF531)
+#define CFG_PROMPT "bf531> " /* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF532)
+#define CFG_PROMPT "bf532> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "bf533> " /* Monitor Command Prompt */
+#endif
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_LOADS_ECHO 1
+
+/*
+ * I2C settings
+ * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
+ */
+#if (CONFIG_SOFT_I2C)
+
+#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
+#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SDA; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SDA; \
+ asm("ssync;"); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SCL; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SCL; \
+ asm("ssync;"); \
+ }
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
+#endif /* CONFIG_SOFT_I2C */
+
+/*
+ * Compact Flash settings
+ */
+
+/* Enabled below option for CF support */
+/* #define CONFIG_STAMP_CF 1 */
+
+#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE)
+
+#define CONFIG_MISC_INIT_R 1
+#define CONFIG_DOS_PARTITION 1
+/*
+ * IDE/ATA stuff
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0x20200000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
+
+#define CFG_ATA_STRIDE 2
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CFG_HZ 1000 /* 1ms time tick */
+
+#define CFG_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+
+#define CONFIG_SPI
+
+#ifdef CONFIG_VIDEO
+#if (CONFIG_VIDEO)
+#define CONFIG_SPLASH_SCREEN 1
+#define CONFIG_SILENT_CONSOLE 1
+#else
+#undef CONFIG_VIDEO
+#endif
+#endif
+
+/*
+ * FLASH organization and environment definitions
+ */
+#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */
+
+/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
+/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
+ B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
+#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
+ B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
+*/
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0xBBC3BBC3
+#define AMBCTL1VAL 0x99B39983
+#define CF_AMBCTL1VAL 0x99B3ffc2
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP 0x8
+#define SHT_STRTAB_VDSP 0x1
+#define ELFSHDRSIZE_VDSP 0x2C
+#define VDSP_ENTRY_ADDR 0xFFA00000
+#endif
+
+#endif
diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
new file mode 100644
index 0000000..f6755ac
--- /dev/null
+++ b/include/configs/bf537-stamp.h
@@ -0,0 +1,502 @@
+/*
+ * U-boot - Configuration file for BF537 STAMP board
+ */
+
+#ifndef __CONFIG_BF537_H__
+#define __CONFIG_BF537_H__
+
+#define CFG_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_BAUDRATE 57600
+/* Set default serial console for bf537 */
+#define CONFIG_UART_CONSOLE 0
+#define CONFIG_BF537 1
+#define CONFIG_BOOTDELAY 5
+/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
+/*#define CONFIG_BF537_STAMP_LEDCMD 1*/
+
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF537_BYPASS_BOOT 0x0011 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF537_PARA_BOOT 0x0012 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF537_SPI_MASTER_BOOT 0x0014 /* Bootmode 3: SPI master mode boot from SPI flash */
+#define BF537_SPI_SLAVE_BOOT 0x0015 /* Bootmode 4: SPI slave mode boot from SPI flash */
+#define BF537_TWI_MASTER_BOOT 0x0016 /* Bootmode 5: TWI master mode boot from EEPROM */
+#define BF537_TWI_SLAVE_BOOT 0x0017 /* Bootmode 6: TWI slave mode boot from EEPROM */
+#define BF537_UART_BOOT 0x0018 /* Bootmode 7: UART slave mdoe boot via UART host */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE BF537_BYPASS_BOOT
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF534 0x34
+#define ADSP_BF536 0x36
+#define ADSP_BF537 0x37
+#define BFIN_CPU ADSP_BF537
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define if want to do post memory test */
+#undef CONFIG_POST_TEST
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+#define CONFIG_RTC_BFIN 1
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
+
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 25000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL*/
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 20
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
+#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#define CONFIG_SPI_BAUD_INITBLOCK 4
+#endif
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#endif
+
+#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
+#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
+#else
+#undef CONFIG_SPI_FLASH_FAST_READ
+#endif
+#endif
+
+#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC32M8A2_75 1
+
+#define CONFIG_LOADS_ECHO 1
+
+/*
+ * rarpb, bootp or dhcp commands will perform only a
+ * configuration lookup from the BOOTP/DHCP server
+ * but not try to load any image using TFTP
+ */
+#define CFG_AUTOLOAD "no"
+
+/*
+ * Network Settings
+ */
+/* network support */
+#if (BFIN_CPU != ADSP_BF534)
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME BF537
+#endif
+
+#define CONFIG_ROOTPATH /romfs
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
+/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */
+
+#define CFG_LONGHELP 1
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
+#define CONFIG_BOOTCOMMAND "run ramboot"
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) && defined(CONFIG_POST_TEST)
+/* POST support */
+#define CONFIG_POST ( CFG_POST_MEMORY | \
+ CFG_POST_UART | \
+ CFG_POST_FLASH | \
+ CFG_POST_ETHER | \
+ CFG_POST_LED | \
+ CFG_POST_BUTTON)
+#else
+#undef CONFIG_POST
+#endif
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
+#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
+#else
+#define CFG_CMD_POST_DIAG 0
+#endif
+
+/* CF-CARD IDE-HDD Support */
+
+/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */
+/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */
+/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */
+
+#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE)
+# define CONFIG_BFIN_IDE 1
+# define ADD_IDE_CMD CFG_CMD_IDE
+#else
+# define ADD_IDE_CMD 0
+#endif
+
+/*#define CONFIG_BF537_NAND */ /* Add nand flash support */
+
+#ifdef CONFIG_BF537_NAND
+# define ADD_NAND_CMD CFG_CMD_NAND
+#else
+# define ADD_NAND_CMD 0
+#endif
+
+#define CONFIG_NETCONSOLE 1
+#define CONFIG_NET_MULTI 1
+
+#if (BFIN_CPU == ADSP_BF534)
+#define CONFIG_BFIN_CMD (CONFIG_CMD_DFL & ~CFG_CMD_NET)
+#else
+#define CONFIG_BFIN_CMD (CONFIG_CMD_DFL | CFG_CMD_PING)
+#endif
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT)
+#define CONFIG_COMMANDS (CONFIG_BFIN_CMD| \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DHCP | \
+ ADD_IDE_CMD | \
+ ADD_NAND_CMD | \
+ CFG_CMD_POST_DIAG | \
+ CFG_CMD_DATE)
+#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#define CONFIG_COMMANDS (CONFIG_BFIN_CMD| \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ ADD_IDE_CMD | \
+ CFG_CMD_DATE)
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
+#define CONFIG_LOADADDR 0x1000000
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT)
+#if (BFIN_CPU != ADSP_BF534)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux;" \
+ "run ramargs;run addip;bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux;" \
+ "run nfsargs;run addip;bootelf\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.bin;" \
+ "protect off 0x20000000 0x2007FFFF;" \
+ "erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \
+ ""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "flashboot=bootm 0x20100000\0" \
+ ""
+#endif
+#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (BFIN_CPU != ADSP_BF534)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux;" \
+ "run ramargs;run addip;bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux;" \
+ "run nfsargs;run addip;bootelf\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.ldr;" \
+ "eeprom write $(loadaddr) 0x0 $(filesize);\0" \
+ ""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "flashboot=bootm 0x20100000\0" \
+ ""
+#endif
+#endif
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (BFIN_CPU == ADSP_BF534)
+#define CFG_PROMPT "serial_bf534> " /* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF536)
+#define CFG_PROMPT "serial_bf536> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "serial_bf537> " /* Monitor Command Prompt */
+#endif
+#else
+#if (BFIN_CPU == ADSP_BF534)
+#define CFG_PROMPT "bf534> " /* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF536)
+#define CFG_PROMPT "bf536> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "bf537> " /* Monitor Command Prompt */
+#endif
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024*1024)
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_MEMTEST_START 0x0 /* memtest works on */
+#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
+#define CFG_LOAD_ADDR CONFIG_LOADADDR /* default load address */
+#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CFG_SDRAM_BASE 0x00000000
+
+#define CFG_FLASH_BASE 0x20000000
+
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_SIZE 0x4000
+#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
+
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) || (BFIN_BOOT_MODE == BF537_UART_BOOT)
+/* for bf537-stamp, usrt boot mode still store env in flash */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20004000
+#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
+#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_ENV_OFFSET 0x4000
+#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
+#endif
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
+/* #if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) */
+#define ENV_IS_EMBEDDED
+/* #endif */
+
+/* JFFS Partition offset set */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR 15
+
+#define CONFIG_SPI
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+
+#define POLL_MODE 1
+#define FLASH_TOT_SECT 71
+#define FLASH_SIZE 0x400000
+#define CFG_FLASH_SIZE 0x400000
+
+/*
+ * Board NAND Infomation
+ */
+
+#define CFG_NAND_ADDR 0x20212000
+#define CFG_NAND_BASE CFG_NAND_ADDR
+#define CFG_MAX_NAND_DEVICE 1
+#define SECTORSIZE 512
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define BFIN_NAND_READY PF3
+
+#define NAND_WAIT_READY(nand) \
+ do { \
+ int timeout = 0; \
+ while(!(*pPORTFIO & PF3)) \
+ if (timeout++ > 100000) \
+ break; \
+ } while (0)
+
+#define BFIN_NAND_CLE (1<<2) /* A2 -> Command Enable */
+#define BFIN_NAND_ALE (1<<1) /* A1 -> Address Enable */
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+/*
+ * Initialize PSD4256 registers for using I2C
+ */
+#define CONFIG_MISC_INIT_R
+
+#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+
+/*
+ * I2C settings
+ * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
+ */
+/* #define CONFIG_SOFT_I2C 1*/ /* I2C bit-banged */
+#define CONFIG_HARD_I2C 1 /* I2C TWI */
+#if defined CONFIG_HARD_I2C
+#define CONFIG_TWICLK_KHZ 50
+#endif
+
+#if defined CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL PF0
+#define PF_SDA PF1
+
+#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
+#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SDA; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SDA; \
+ asm("ssync;"); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SCL; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SCL; \
+ asm("ssync;"); \
+ }
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#endif
+
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
+
+/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
+/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
+ ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
+#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
+ B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
+*/
+
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0x7BB07BB0
+#define AMBCTL1VAL 0xFFC27BB0
+
+#define CONFIG_VDSP 1
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP 0x8
+#define SHT_STRTAB_VDSP 0x1
+#define ELFSHDRSIZE_VDSP 0x2C
+#define VDSP_ENTRY_ADDR 0xFFA00000
+#endif
+
+#if defined(CONFIG_BFIN_IDE)
+
+#define CONFIG_DOS_PARTITION 1
+/*
+ * IDE/ATA stuff
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#undef AMBCTL1VAL
+#define AMBCTL1VAL 0xFFC3FFC3
+
+#define CONFIG_CF_ATASEL_DIS 0x20311800
+#define CONFIG_CF_ATASEL_ENA 0x20311802
+
+#if defined(CONFIG_BFIN_TRUE_IDE)
+/*
+ * Note that these settings aren't for the most part used in include/ata.h
+ * when all of the ATA registers are setup
+ */
+#define CFG_ATA_BASE_ADDR 0x2031C000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
+#define CFG_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */
+#endif /* CONFIG_BFIN_TRUE_IDE */
+
+#if defined(CONFIG_BFIN_CF_IDE) /* USE CompactFlash Storage Card in the common memory space */
+#define CFG_ATA_BASE_ADDR 0x20211800
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x000E /* Offset for alternate registers */
+#define CFG_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */
+#endif /* CONFIG_BFIN_CF_IDE */
+
+#if defined(CONFIG_BFIN_HDD_IDE) /* USE TRUE IDE */
+#define CFG_ATA_BASE_ADDR 0x20314000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
+#define CFG_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */
+
+#undef CONFIG_SCLK_DIV
+#define CONFIG_SCLK_DIV 8
+#endif /* CONFIG_BFIN_HDD_IDE */
+
+#endif /*CONFIG_BFIN_IDE */
+
+#endif
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
new file mode 100644
index 0000000..8d826fa
--- /dev/null
+++ b/include/configs/bf561-ezkit.h
@@ -0,0 +1,244 @@
+/*
+ * U-boot - Configuration file for BF561 EZKIT board
+ */
+
+#ifndef __CONFIG_EZKIT561_H__
+#define __CONFIG_EZKIT561_H__
+
+#define CONFIG_VDSP 1
+#define CONFIG_BF561 1
+
+#define CFG_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_BAUDRATE 57600
+/* Set default serial console for bf537 */
+#define CONFIG_UART_CONSOLE 0
+#define CONFIG_EZKIT561 1
+#define CONFIG_BOOTDELAY 5
+
+#define CONFIG_PANIC_HANG 1
+
+/*
+* Boot Mode Set
+* Blackfin can support several boot modes
+*/
+#define BF561_BYPASS_BOOT 0x21
+#define BF561_PARA_BOOT 0x22
+#define BF561_SPI_BOOT 0x24
+/* Define the boot mode */
+#define BFIN_BOOT_MODE BF561_BYPASS_BOOT
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/*
+ * Stringize definitions - needed for environmental settings
+ */
+#define STRINGIZE2(x) #x
+#define STRINGIZE(x) STRINGIZE2(x)
+
+/*
+ * Board settings
+ */
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x2C010300
+#define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024)
+#define CONFIG_SMC_USE_32_BIT 1
+#define CONFIG_MISC_INIT_R 1
+
+/*
+ * Clock settings
+ */
+
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 30000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 20
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
+#define CONFIG_SPI_BAUD_INITBLOCK 4
+
+/*
+ * Network settings
+ */
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME ezkit561
+#define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs
+#endif /* CONFIG_DRIVER_SMC91111 */
+
+/*
+ * Flash settings
+ */
+
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_FLASH_CFI_AMD_RESET
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_FLASH_BASE 0x20000000
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 135 /* max number of sectors on one chip */
+#define CFG_ENV_ADDR 0x20020000
+#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
+/* JFFS Partition offset set */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR 8
+
+/*
+ * SDRAM settings & memory map
+ */
+
+#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC16M16A2TG_75 1
+
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
+
+#define CFG_MEMTEST_START 0x0 /* memtest works on */
+#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
+
+#define CONFIG_LOADADDR 0x01000000 /* default load address */
+#define CFG_LOAD_ADDR CONFIG_LOADADDR
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
+
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+
+#define CFG_GBL_DATA_SIZE 0x4000
+#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#endif
+
+/*
+ * Command settings
+ */
+
+#define CFG_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */
+ /* only perform a configuration */
+ /* lookup from the BOOTP/DHCP server */
+ /* but not try to load any image */
+ /* using TFTP */
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */
+ /* currently its disabled */
+#define CONFIG_BOOTCOMMAND "run ramboot"
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
+
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_PING | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_DHCP)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+ "$(rootpath) console=ttyBF0,57600\0" \
+ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux; " \
+ "run ramargs; run addip; bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux; " \
+ "run nfsargs; run addip; bootelf\0" \
+ "update=tftpboot $(loadaddr) u-boot.bin; " \
+ "protect off 0x20000000 0x2003FFFF; " \
+ "erase 0x20000000 0x2003FFFF; " \
+ "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
+ ""
+#else
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "flashboot=bootm 0x20100000\0" \
+ ""
+#endif
+
+#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Console settings
+ */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_LOADS_ECHO 1
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
+#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+
+/*
+ * FLASH organization and environment definitions
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#define AMGCTLVAL 0x3F
+#define AMBCTL0VAL 0x7BB07BB0
+#define AMBCTL1VAL 0xFFC27BB0
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP 0x8
+#define SHT_STRTAB_VDSP 0x1
+#define ELFSHDRSIZE_VDSP 0x2C
+#define VDSP_ENTRY_ADDR 0xFFA00000
+#endif
+
+#endif /* __CONFIG_EZKIT561_H__ */
diff --git a/include/configs/ezkit533.h b/include/configs/ezkit533.h
deleted file mode 100644
index 5eda673..0000000
--- a/include/configs/ezkit533.h
+++ /dev/null
@@ -1,188 +0,0 @@
-#ifndef __CONFIG_EZKIT533_H__
-#define __CONFIG_EZKIT533_H__
-
-#define CFG_LONGHELP 1
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_STAMP 1
-#define CONFIG_BOOTDELAY 5
-
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20310300
-#if 0
-#define CONFIG_MII
-#define CFG_DISCOVER_PHY
-#endif
-
-#define CONFIG_RTC_BF533 1
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 27000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 22
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC16M16A2TG_75 1
-
-#define CONFIG_LOADS_ECHO 1
-
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_PING | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_DATE)
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off"
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x01F00000 /* 1 ... 31 MB in DRAM */
-#define CFG_LOAD_ADDR 0x01000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_MAX_RAM_SIZE 0x02000000
-#define CFG_FLASH_BASE 0x20000000
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE 0x4000
-#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
-
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CFG_FLASH0_BASE 0x20000000
-#define CFG_FLASH1_BASE 0x20200000
-#define CFG_FLASH2_BASE 0x20280000
-#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20020000
-#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
-
-/* JFFS Partition offset set */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
-
-
-/*
- * Stack sizes
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-#define POLL_MODE 1
-#define FLASH_TOT_SECT 40
-#define FLASH_SIZE 0x220000
-#define CFG_FLASH_SIZE 0x220000
-
-/*
- * Initialize PSD4256 registers for using I2C
- */
-#define CONFIG_MISC_INIT_R
-
-/*
- * I2C settings
- * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
- */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PF_SCL PF0
-#define PF_SDA PF1
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
-
-
-#define __ADSPLPBLACKFIN__ 1
-#define __ADSPBF533__ 1
-
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
-
-#define CONFIG_VDSP 1
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
-
-#endif
diff --git a/include/configs/stamp.h b/include/configs/stamp.h
deleted file mode 100644
index 248ca70..0000000
--- a/include/configs/stamp.h
+++ /dev/null
@@ -1,333 +0,0 @@
-/*
- * U-boot - stamp.h Configuration file for STAMP board
- * having BF533 processor
- *
- * Copyright (c) 2005 blackfin.uclinux.org
- *
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_STAMP_H__
-#define __CONFIG_STAMP_H__
-
-/*
- * Board settings
- *
- */
-
-#define __ADSPLPBLACKFIN__ 1
-#define __ADSPBF533__ 1
-#define CONFIG_STAMP 1
-#define CONFIG_RTC_BF533 1
-
-/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES 1
-
-#define CONFIG_VDSP 1
-
-/*
- * Clock settings
- *
- */
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 45
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 6
-
-/*
- * Network Settings
- */
-/* network support */
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME STAMP
-#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
-
-/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
-
-/*
- * Command settings
- *
- */
-
-#define CFG_LONGHELP 1
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
-#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n"
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_PING | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_CACHE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_DATE)
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):eth0:off\0" \
- "ramboot=tftpboot 0x1000000 linux;" \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot 0x1000000 linux;" \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- ""
-
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Console settings
- *
- */
-
-#define CONFIG_BAUDRATE 57600
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#define CFG_PROMPT "stamp>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_LOADS_ECHO 1
-
-/*
- * Network settings
- *
- */
-
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20300300
-/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define HARDCODE_MAC 1 */
-
-/*
- * Flash settings
- *
- */
-
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_CFI_AMD_RESET
-
-#define CFG_ENV_IS_IN_FLASH 1
-
-#define CFG_FLASH_BASE 0x20000000
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-
-#define CFG_ENV_ADDR 0x20020000
-#define CFG_ENV_SIZE 0x10000
-#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
-
-#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
-#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-/* JFFS Partition offset set */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
-
-/*
- * following timeouts shall be used once the
- * Flash real protection is enabled
- */
-#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
-#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
-
-/*
- * I2C settings
- * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
- */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PF_SCL PF3
-#define PF_SDA PF2
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
-
-/*
- * Compact Flash settings
- */
-
-/* Enabled below option for CF support */
-/* #define CONFIG_STAMP_CF 1 */
-
-#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE)
-
-#define CONFIG_MISC_INIT_R 1
-#define CONFIG_DOS_PARTITION 1
-
-/*
- * IDE/ATA stuff
- */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define CFG_ATA_BASE_ADDR 0x20200000
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
-
-#define CFG_ATA_STRIDE 2
-#endif
-
-/*
- * SDRAM settings
- *
- */
-
-#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x07EFFFFF /* 1 ... 127 MB in DRAM */
-#define CFG_LOAD_ADDR 0x01000000 /* default load address */
-
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_MAX_RAM_SIZE 0x08000000
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_HZ 1000 /* 1ms time tick */
-
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE 0x4000
-#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
-
-#define CFG_LARGE_IMAGE_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
-
-/*
- * Stack sizes
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-/*
- * FLASH organization and environment definitions
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
-/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
- B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
-#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
- B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
-*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0xBBC3BBC3
-#define AMBCTL1VAL 0x99B39983
-#define CF_AMBCTL1VAL 0x99B3ffc2
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
-
-#endif
generated by cgit v1.1 at 2024-12-18 14:15:44 +0000