diff options
Diffstat (limited to 'include/configs')
144 files changed, 1142 insertions, 1282 deletions
diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h index ae0a873..e707075 100644 --- a/include/configs/AP1000.h +++ b/include/configs/AP1000.h @@ -52,12 +52,6 @@ #define CONFIG_BOOTCOMMAND "" /* autoboot command */ -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO - #define CONFIG_BOOTARGS "console=ttyS0,57600" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ diff --git a/include/configs/APC405.h b/include/configs/APC405.h index a7724ad..cb3f80b 100644 --- a/include/configs/APC405.h +++ b/include/configs/APC405.h @@ -176,6 +176,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */ /* The following table includes the supported baudrates */ @@ -264,16 +270,10 @@ /* * FLASH organization */ -#ifndef __ASSEMBLY__ -extern int flash_banks; -#endif - #define CONFIG_SYS_FLASH_BASE 0xFE000000 #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CONFIG_SYS_MAX_FLASH_BANKS flash_banks /* max num of flash banks */ - /* updated in board_early_init_r */ #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 #define CONFIG_SYS_FLASH_QUIET_TEST 1 #define CONFIG_SYS_FLASH_INCREMENT 0x01000000 diff --git a/include/configs/AR405.h b/include/configs/AR405.h index 45c64c2..568ce15 100644 --- a/include/configs/AR405.h +++ b/include/configs/AR405.h @@ -127,6 +127,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */ /* The following table includes the supported baudrates */ diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 4cb8052..789f750 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -124,9 +124,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -335,12 +340,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 #define CONFIG_SYS_DUART_RST (0x80000000 >> 14) diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h index c133033..58f0c1f 100644 --- a/include/configs/ATUM8548.h +++ b/include/configs/ATUM8548.h @@ -200,7 +200,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h index 115a6f9..ad075b8 100644 --- a/include/configs/CANBT.h +++ b/include/configs/CANBT.h @@ -100,6 +100,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */ /* The following table includes the supported baudrates */ diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h index 002435e..764f71b 100644 --- a/include/configs/CATcenter.h +++ b/include/configs/CATcenter.h @@ -86,7 +86,11 @@ # error "* External frequency (SysClk) not defined! *" #endif -#define CONFIG_UART1_CONSOLE 1 /* Use second UART */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ @@ -527,13 +531,13 @@ * GPIO0[30] - EMAC0 input * GPIO0[31] - EMAC1 reject packet as output */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -/*#define CONFIG_SYS_GPIO0_ISR1L 0x15555445*/ -#define CONFIG_SYS_GPIO0_ISR1L 0x15555444 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ +#define CONFIG_SYS_GPIO0_ISR1H 0x15555444 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 /* diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h index 2b6786b..9c57acb 100644 --- a/include/configs/CMS700.h +++ b/include/configs/CMS700.h @@ -122,9 +122,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -301,12 +306,12 @@ /* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */ /* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */ /* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000500 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* 16 ... 31 */ -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */ -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_OSRL 0x40000500 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_ISR1H 0x14000045 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 16 ... 31 */ #define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */ #define CONFIG_SYS_EEPROM_WP (0x80000000 >> 8) /* GPIO8 */ diff --git a/include/configs/CPC45.h b/include/configs/CPC45.h index 91d262a..668cfa2 100644 --- a/include/configs/CPC45.h +++ b/include/configs/CPC45.h @@ -347,13 +347,12 @@ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define SRAM_BASE 0x80000000 /* SRAM base address */ -#define SRAM_END 0x801FFFFF /*----------------------------------------------------------------------*/ /* CPC45 Memory Map */ /*----------------------------------------------------------------------*/ #define SRAM_BASE 0x80000000 /* SRAM base address */ +#define SRAM_END 0x801FFFFF #define ST16552_A_BASE 0x80200000 /* ST16552 channel A */ #define ST16552_B_BASE 0x80400000 /* ST16552 channel A */ #define BCSR_BASE 0x80600000 /* board control / status registers */ @@ -361,6 +360,8 @@ #define PCMCIA_MEM_BASE 0x83000000 /* PCMCIA memory window base */ #define PCMCIA_IO_BASE 0xFE000000 /* PCMCIA IO window base */ +#define CONFIG_SYS_SRAM_BASE SRAM_BASE +#define CONFIG_SYS_SRAM_SIZE (SRAM_END - SRAM_BASE + 1) /*---------------------------------------------------------------------*/ /* CPC45 Control/Status Registers */ diff --git a/include/configs/CPCI2DP.h b/include/configs/CPCI2DP.h index 9221211..c6882fd 100644 --- a/include/configs/CPCI2DP.h +++ b/include/configs/CPCI2DP.h @@ -111,9 +111,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index 3e7020d..da57b04 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -125,6 +125,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index d3000f6..d682d37 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -134,6 +134,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index d376344..1c521f2 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -133,6 +133,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index 07acab0..c7b7931 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -135,6 +135,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/CPCIISER4.h b/include/configs/CPCIISER4.h index 5b50bcf..f114290 100644 --- a/include/configs/CPCIISER4.h +++ b/include/configs/CPCIISER4.h @@ -110,6 +110,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 1843200 /* use external serial clock */ /* The following table includes the supported baudrates */ diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h index 9ab30ec..f6cd760 100644 --- a/include/configs/CRAYL1.h +++ b/include/configs/CRAYL1.h @@ -47,6 +47,12 @@ #define CONFIG_MISC_INIT_R 1 /* so that a misc_init_r() is called */ #define CONFIG_NET_MULTI +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + /* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to * keep possible initrd ramdisk decompression out. This is in k (1024 bytes) #define CONFIG_PRAM 16 diff --git a/include/configs/DP405.h b/include/configs/DP405.h index 4423f2a..5311dfb 100644 --- a/include/configs/DP405.h +++ b/include/configs/DP405.h @@ -97,9 +97,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -243,12 +248,12 @@ /* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */ /* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */ /* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000540 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* 16 ... 31 */ -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */ -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_OSRL 0x40000540 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_ISR1H 0x14000045 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 16 ... 31 */ #define CONFIG_SYS_GPIO0_TCR 0xB7FE0014 /* 0 ... 31 */ /* diff --git a/include/configs/DU405.h b/include/configs/DU405.h index 8f1fc78..6ba9f13 100644 --- a/include/configs/DU405.h +++ b/include/configs/DU405.h @@ -73,6 +73,11 @@ #include <config_cmd_default.h> #undef CONFIG_CMD_NFS +#undef CONFIG_CMD_EDITENV +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_CONSOLE +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_LOADS #define CONFIG_CMD_IDE #define CONFIG_CMD_ELF #define CONFIG_CMD_MII @@ -109,6 +114,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external serial clock */ /* The following table includes the supported baudrates */ @@ -126,32 +137,6 @@ #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ /*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0404 /* PCI Device ID: CPCI-ISER4 */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffe00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffe00001 /* 2MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- * IDE/ATA stuff *----------------------------------------------------------------------- */ diff --git a/include/configs/DU440.h b/include/configs/DU440.h index 830466f..9c34994 100644 --- a/include/configs/DU440.h +++ b/include/configs/DU440.h @@ -64,9 +64,6 @@ #define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH #define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */ -/* Don't change either of these */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ - #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 @@ -86,10 +83,14 @@ /* * Serial Port */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI 1 -#undef CONFIG_UART1_CONSOLE #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} diff --git a/include/configs/ERIC.h b/include/configs/ERIC.h index e07f9a1..da3b4ae 100644 --- a/include/configs/ERIC.h +++ b/include/configs/ERIC.h @@ -139,6 +139,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 14318180 /* The following table includes the supported baudrates */ diff --git a/include/configs/G2000.h b/include/configs/G2000.h index d2883eb..e2e6cb2 100644 --- a/include/configs/G2000.h +++ b/include/configs/G2000.h @@ -151,9 +151,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -367,12 +372,12 @@ * * following GPIO setting changed for G20000, 080304 */ -#define CONFIG_SYS_GPIO0_OSRH 0x40005555 -#define CONFIG_SYS_GPIO0_OSRL 0x40000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40005555 +#define CONFIG_SYS_GPIO0_OSRH 0x40000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 /* diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 01e0bc6..0db9298 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -176,9 +176,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -461,12 +466,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555440 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555440 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FE0017 #define CONFIG_SYS_LCD_ENDIAN (0x80000000 >> 7) diff --git a/include/configs/HMI10.h b/include/configs/HMI10.h deleted file mode 100644 index 2747d8c..0000000 --- a/include/configs/HMI10.h +++ /dev/null @@ -1,504 +0,0 @@ -/* - * (C) Copyright 2000-2008 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_HMI10 -#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ -#define CONFIG_TQM823L 1 /* ...on a TQM8xxL module */ - -#define CONFIG_LCD -#define CONFIG_NEC_NL6448BC33_54 /* NEC NL6448BC33_54 display */ - -#ifdef CONFIG_LCD /* with LCD controller ? */ -#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ -#endif - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#define CONFIG_SYS_SMC_RXBUFLEN 128 -#define CONFIG_SYS_MAXIDLE 10 -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ - -#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ -#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ -#define CONFIG_PS2SERIAL 2 /* .. on COM3 */ -#define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ - -#define CONFIG_BOOTCOUNT_LIMIT - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BOARD_TYPES 1 /* support board types */ - -#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_8xx\0" \ - "bootfile=/tftpboot/HMI10/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOARD_EARLY_INIT_R 1 -#define CONFIG_MISC_INIT_R 1 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -/* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -/* Software (bit-bang) I2C driver configuration */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ - -#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - -#ifdef CONFIG_SPLASH_SCREEN - #define CONFIG_CMD_BMP -#endif - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ - -#if 0 -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ -#endif -#ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFFF00000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ - -/* use CFI flash driver */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/*----------------------------------------------------------------------- - * Hardware Information Block - */ -#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#ifndef CONFIG_CAN_DRIVER -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) -#else /* we must activate GPL5 in the SIUMCR for CAN */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) -#endif /* CONFIG_CAN_DRIVER */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - * - * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! - */ -#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0100000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4100000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8100000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC100000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) -#define PCMCIA_MEM_WIN_NO 5 -#define NSCU_OE_INV 1 /* PCMCIA_GCRX_CXOE is inverted */ - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ - -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ -#ifndef CONFIG_STATUS_LED /* Status and IDE LED's are mutually exclusive */ -#define CONFIG_IDE_LED 1 /* LED for ide supported */ -#endif - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* - * FLASH timing: - */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \ - OR_SCY_3_CLK | OR_EHTR | OR_BI) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM -#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) - -/* - * BR2/3 and OR2/3 (SDRAM) - * - */ -#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ -#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */ -#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ - -/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 - -#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM ) -#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -#ifndef CONFIG_CAN_DRIVER -#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM -#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) -#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */ -#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ -#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ -#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI) -#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \ - BR_PS_8 | BR_MS_UPMB | BR_V ) -#endif /* CONFIG_CAN_DRIVER */ - -/* - * Memory Periodic Timer Prescaler - * - * The Divider for PTA (refresh timer) configuration is based on an - * example SDRAM configuration (64 MBit, one bank). The adjustment to - * the number of chip selects (NCS) and the actually needed refresh - * rate is done by setting MPTPR. - * - * PTA is calculated from - * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) - * - * gclk CPU clock (not bus clock!) - * Trefresh Refresh cycle * 4 (four word bursts used) - * - * 4096 Rows from SDRAM example configuration - * 1000 factor s -> ms - * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration - * 4 Number of refresh cycles per period - * 64 Refresh cycle in ms per number of rows - * -------------------------------------------- - * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 - * - * 50 MHz => 50.000.000 / Divider = 98 - * 66 Mhz => 66.000.000 / Divider = 129 - * 80 Mhz => 80.000.000 / Divider = 156 - */ - -#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64)) -#define CONFIG_SYS_MAMR_PTA 98 - -/* - * For 16 MBit, refresh rates could be 31.3 us - * (= 64 ms / 2K = 125 / quad bursts). - * For a simpler initialization, 15.6 us is used instead. - * - * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks - * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank - */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_HWCONFIG 1 - -#endif /* __CONFIG_H */ diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h index 8c6d5ed..5dea96e 100644 --- a/include/configs/HUB405.h +++ b/include/configs/HUB405.h @@ -118,9 +118,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -334,12 +339,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 #define CONFIG_SYS_DUART_RST (0x80000000 >> 14) diff --git a/include/configs/IDS8247.h b/include/configs/IDS8247.h index 71bb7b4..4e73941 100644 --- a/include/configs/IDS8247.h +++ b/include/configs/IDS8247.h @@ -227,7 +227,7 @@ #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CONFIG_SYS_FLASH_BANKS_LIST { 0xFF800000 } -#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ /* What should the base address of the main FLASH be and how big is * it (in MBytes)? This must contain TEXT_BASE from board/ids8247/config.mk * The main FLASH is whichever is connected to *CS0. @@ -242,7 +242,6 @@ /*----------------------------------------------------------------------- * FLASH organization */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ diff --git a/include/configs/IP860.h b/include/configs/IP860.h index be63ea5..ed6b7fd 100644 --- a/include/configs/IP860.h +++ b/include/configs/IP860.h @@ -375,6 +375,8 @@ extern unsigned long ip860_get_clk_freq (void); #define SRAM_SIZE (1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK))) #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR3 /* Make sure to map early */ #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_BR3 /* in case it's used for ENV */ +#define CONFIG_SYS_SRAM_BASE SRAM_BASE +#define CONFIG_SYS_SRAM_SIZE SRAM_SIZE /* * BR4/OR4 - Board Control & Status (8 bit) diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index 5d3a744..3961100 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -280,7 +280,7 @@ #endif #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* @@ -317,6 +317,10 @@ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ diff --git a/include/configs/JSE.h b/include/configs/JSE.h index 98f5661..b0b1175 100644 --- a/include/configs/JSE.h +++ b/include/configs/JSE.h @@ -95,18 +95,16 @@ #define CONFIG_ENV_OFFSET 0x00 #define CONFIG_ENV_SIZE 512 - /* The JSE connects UART1 to the console tap connector. */ -#define CONFIG_UART1_CONSOLE 1 +#define CONFIG_CONS_INDEX 2 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + /* Set console baudrate to 9600 */ #define CONFIG_BAUDRATE 9600 -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO - /* * Configuration related to auto-boot. * diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h index 05f7254..94cc317 100644 --- a/include/configs/KAREF.h +++ b/include/configs/KAREF.h @@ -59,7 +59,6 @@ #define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE 0xfff80000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -90,7 +89,11 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SERIAL_MULTI 1 #define CONFIG_BAUDRATE 9600 diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h index 30a3035..2e63306 100644 --- a/include/configs/METROBOX.h +++ b/include/configs/METROBOX.h @@ -125,7 +125,6 @@ #define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE 0xfff80000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -152,7 +151,11 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SERIAL_MULTI 1 #define CONFIG_BAUDRATE 9600 diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h index ff9496b..bfff750 100644 --- a/include/configs/MIP405.h +++ b/include/configs/MIP405.h @@ -176,6 +176,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 916667 diff --git a/include/configs/ML2.h b/include/configs/ML2.h index 5fcc173..2fc0119 100644 --- a/include/configs/ML2.h +++ b/include/configs/ML2.h @@ -52,16 +52,6 @@ #define CONFIG_PREBOOT "fsload 0x00100000 /boot/image" -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ -#if 0 -#define CONFIG_SERIAL_SOFTWARE_FIFO 4000 -#else -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#endif - #if 0 #define CONFIG_BOOTARGS "root=/dev/nfs " \ "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \ diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h index 6cd5da7..1314271 100644 --- a/include/configs/MPC8308RDB.h +++ b/include/configs/MPC8308RDB.h @@ -85,10 +85,27 @@ /* * System IO Config */ -#define CONFIG_SYS_SICRH 0x01b7d103 -#define CONFIG_SYS_SICRL 0x00000040 /* 3.3V, no delay */ - -#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ +#define CONFIG_SYS_SICRH (\ + SICRH_ESDHC_A_SD |\ + SICRH_ESDHC_B_SD |\ + SICRH_ESDHC_C_SD |\ + SICRH_GPIO_A_TSEC2 |\ + SICRH_GPIO_B_TSEC2_GTX_CLK125 |\ + SICRH_IEEE1588_A_GPIO |\ + SICRH_USB |\ + SICRH_GTM_GPIO |\ + SICRH_IEEE1588_B_GPIO |\ + SICRH_ETSEC2_CRS |\ + SICRH_GPIOSEL_1 |\ + SICRH_TMROBI_V3P3 |\ + SICRH_TSOBI1_V2P5 |\ + SICRH_TSOBI2_V2P5) /* 0x01b7d103 */ +#define CONFIG_SYS_SICRL (\ + SICRL_SPI_PF0 |\ + SICRL_UART_PF0 |\ + SICRL_IRQ_PF0 |\ + SICRL_I2C2_PF0 |\ + SICRL_ETSEC1_GTX_CLK125) /* 0x00000040 */ /* * IMMR new address @@ -218,7 +235,7 @@ /* Window base at flash base */ #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */ +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) #define CONFIG_SYS_BR0_PRELIM (\ CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\ @@ -260,7 +277,7 @@ /* 0xFFFF8396 */ #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE -#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) #ifdef CONFIG_VSC7385_ENET #define CONFIG_TSEC2 @@ -270,7 +287,7 @@ /* Access window base at VSC7385 base */ #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE /* Access window size 128K */ -#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 +#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB) /* The flash address and size of the VSC7385 firmware image */ #define CONFIG_VSC7385_IMAGE 0xFE7FE000 #define CONFIG_VSC7385_IMAGE_SIZE 8192 @@ -279,7 +296,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -336,19 +352,8 @@ #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 -/* - * Fake PCIE2 definitions: there is no PCIE2 on this board but the code - * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this - */ -#define CONFIG_SYS_PCIE2_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 -#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 -#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 +/* enable PCIE clock */ +#define CONFIG_SYS_SCCR_PCIEXP1CM 1 #define CONFIG_PCI #define CONFIG_PCIE @@ -439,10 +444,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 524afa5..3fdd1b0 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -1,5 +1,5 @@ /* - * Copyright (C) Freescale Semiconductor, Inc. 2006. + * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010. * * See file CREDITS for list of people who contributed to this * project. @@ -232,6 +232,13 @@ #define CONFIG_SYS_NAND_BASE 0xE2800000 #endif +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITION +#define CONFIG_CMD_MTDPARTS +#define MTDIDS_DEFAULT "nand0=e2800000.flash" +#define MTDPARTS_DEFAULT \ + "mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)" + #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND 1 @@ -453,10 +460,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index f1b110b..abc29c0 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2007-2009 Freescale Semiconductor, Inc. + * Copyright (C) 2007-2010 Freescale Semiconductor, Inc. * * Dave Liu <daveliu@freescale.com> * @@ -243,6 +243,13 @@ #define CONFIG_SYS_NAND_BASE 0xE0600000 #endif +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITION +#define CONFIG_CMD_MTDPARTS +#define MTDIDS_DEFAULT "nand0=e0600000.flash" +#define MTDPARTS_DEFAULT \ + "mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)" + #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE 1 #define CONFIG_CMD_NAND 1 @@ -298,7 +305,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -529,10 +535,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 9a296a1..0719fcea 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -262,7 +262,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -430,10 +429,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index 68ff191..bed62bd 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -273,7 +273,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -447,10 +446,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 73dbea4..55e9de0 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -283,7 +283,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -496,10 +495,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 9be571f..117f745 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -329,7 +329,6 @@ boards, we say we have two, but don't display a message if we find only one. */ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -539,10 +538,10 @@ boards, we say we have two, but don't display a message if we find only one. */ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index c58e003..d7381aa 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -307,7 +307,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -487,10 +486,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h index 9fa577d..fc53ecc 100644 --- a/include/configs/MPC8360ERDK.h +++ b/include/configs/MPC8360ERDK.h @@ -237,7 +237,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -404,10 +403,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 9092755..8546ebc 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -299,7 +299,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -537,10 +536,10 @@ extern int board_pci_host_broken(void); /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 79dadc4..20c2304 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -316,7 +316,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -545,10 +544,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 2a3c058..0a9f47b 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -400,7 +400,6 @@ * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 577c276..c133895 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -237,7 +237,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h index 7daf934..75227a6 100644 --- a/include/configs/MPC8540EVAL.h +++ b/include/configs/MPC8540EVAL.h @@ -173,7 +173,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 8797b30..c3167e9 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -263,7 +263,6 @@ extern unsigned long get_clock_freq(void); /* Serial Port */ #define CONFIG_CONS_INDEX 2 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index d1ac32f..1804582 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -214,7 +214,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 33f49f5..e1e4acf 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -282,7 +282,6 @@ extern unsigned long get_clock_freq(void); /* Serial Port */ #define CONFIG_CONS_INDEX 2 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 0f71f11..b0dd175 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -261,7 +261,6 @@ extern unsigned long get_clock_freq(void); /* Serial Port */ #define CONFIG_CONS_INDEX 2 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 2dc2932..a98ecde 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -244,7 +244,6 @@ extern unsigned long get_clock_freq(void); /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 8177db3..8ffd458 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -276,7 +276,6 @@ extern unsigned long get_clock_freq(void); /* Serial Port */ #define CONFIG_CONS_INDEX 1 #define CONFIG_SERIAL_MULTI 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 081661e..34ebbdb 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -333,7 +333,6 @@ * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 4d9606e..645d947 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -24,9 +24,12 @@ /* video */ #undef CONFIG_VIDEO -#if defined(CONFIG_VIDEO) +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP #define CONFIG_CFB_CONSOLE #define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO #endif #ifdef RUN_DIAG @@ -218,7 +221,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 974cb6b..3b80d14 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -275,7 +275,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h index c28eb64..25d8077 100644 --- a/include/configs/MVBLM7.h +++ b/include/configs/MVBLM7.h @@ -150,7 +150,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -300,10 +299,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_HRCW_LOW 0x0 #define CONFIG_SYS_HRCW_HIGH 0x0 diff --git a/include/configs/MVSMR.h b/include/configs/MVSMR.h index 6492068..000c4c6 100644 --- a/include/configs/MVSMR.h +++ b/include/configs/MVSMR.h @@ -185,7 +185,6 @@ */ #define CONFIG_ENV_IS_IN_FLASH #undef CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_HAS_UID #define CONFIG_OVERWRITE_ETHADDR_ONCE #define CONFIG_ENV_OFFSET 0x8000 diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h index 55471af..ad2e4da 100644 --- a/include/configs/OCRTC.h +++ b/include/configs/OCRTC.h @@ -105,6 +105,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/ORSG.h b/include/configs/ORSG.h index 1424713..3d35362 100644 --- a/include/configs/ORSG.h +++ b/include/configs/ORSG.h @@ -105,6 +105,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 7e901e1..fa45b5b 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -281,7 +281,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 79ce2c0..74cff0c 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -337,7 +337,6 @@ * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/PCI405.h b/include/configs/PCI405.h index 0d443ea..244d6fe 100644 --- a/include/configs/PCI405.h +++ b/include/configs/PCI405.h @@ -110,6 +110,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h index 3e57c0b..2901cfd 100644 --- a/include/configs/PIP405.h +++ b/include/configs/PIP405.h @@ -167,6 +167,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index f917eb5..928ed8e 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -135,9 +135,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -379,12 +384,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x00000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x00000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0x77FE0014 #define CONFIG_SYS_DUART_RST (0x80000000 >> 14) diff --git a/include/configs/PM854.h b/include/configs/PM854.h index 7426bca..cf8a8cf 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -174,7 +174,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h index 00a12fb..c420efe 100644 --- a/include/configs/PMC405.h +++ b/include/configs/PMC405.h @@ -130,6 +130,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock */ #define CONFIG_SYS_BASE_BAUD 806400 diff --git a/include/configs/PMC405DE.h b/include/configs/PMC405DE.h index 2c048dd..5b1048e 100644 --- a/include/configs/PMC405DE.h +++ b/include/configs/PMC405DE.h @@ -107,9 +107,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x3000000 /* 1 ... 48 MB in DRAM */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index cc0ea7f..bf2247d 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -72,9 +72,6 @@ #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 #define CONFIG_SYS_PCI_MEMSIZE 0x80000000 /* 2GB! */ -/* Don't change either of these */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ - #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 @@ -95,10 +92,14 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 -#undef CONFIG_UART1_CONSOLE /* console on front panel */ +#define CONFIG_SERIAL_MULTI 1 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index 44f03dc..f9b2014 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -191,6 +191,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 @@ -542,13 +548,13 @@ * GPIO0[30] - EMAC0 input * GPIO0[31] - EMAC1 reject packet as output */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -/*#define CONFIG_SYS_GPIO0_ISR1L 0x15555445*/ -#define CONFIG_SYS_GPIO0_ISR1L 0x15555444 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ +#define CONFIG_SYS_GPIO0_ISR1H 0x15555444 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 /* @@ -577,17 +583,6 @@ #define DIMM_READ_ADDR 0xAB #define DIMM_WRITE_ADDR 0xAA -#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */ -#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */ -#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */ -#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register */ -#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */ -#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */ -#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */ -#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */ -#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */ -#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */ - /* Defines for CPC0_PLLMR1 Register fields */ #define PLL_ACTIVE 0x80000000 #define CPC0_PLLMR1_SSCS 0x80000000 diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index 5d424dd..d6b3cb8 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -205,7 +205,6 @@ #undef CONFIG_CONS_NONE /* define if console on something else */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h index 70b7489..9c8c318 100644 --- a/include/configs/SIMPC8313.h +++ b/include/configs/SIMPC8313.h @@ -373,10 +373,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index c1e0e64..d0c6a4d 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -101,10 +101,6 @@ * defined as tqm834x_num_flash_banks. */ #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 -#ifndef __ASSEMBLY__ -extern int tqm834x_num_flash_banks; -#endif -#define CONFIG_SYS_MAX_FLASH_BANKS (tqm834x_num_flash_banks) #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */ @@ -166,7 +162,6 @@ extern int tqm834x_num_flash_banks; * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -359,10 +354,10 @@ extern int tqm834x_num_flash_banks; /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index abbaf38..ccb339d 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -256,7 +256,6 @@ #else /* !CONFIG_TQM8560 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h index 9c91fcc..b9ea610 100644 --- a/include/configs/VOH405.h +++ b/include/configs/VOH405.h @@ -133,9 +133,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -388,12 +393,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs -> GPIO */ -#define CONFIG_SYS_GPIO0_OSRH 0x00000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555440 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x00000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555440 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0x777E0017 #define CONFIG_SYS_DUART_RST (0x80000000 >> 14) diff --git a/include/configs/VOM405.h b/include/configs/VOM405.h index 871e4c3..a88b41a 100644 --- a/include/configs/VOM405.h +++ b/include/configs/VOM405.h @@ -120,9 +120,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -273,12 +278,12 @@ /* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */ /* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */ /* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000500 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* 16 ... 31 */ -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */ -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 0 ... 15 */ -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_OSRL 0x40000500 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_ISR1H 0x14000045 /* 16 ... 31 */ +#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 0 ... 15 */ +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 16 ... 31 */ #define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */ /* diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h index f06bfe5..0fbe80c 100644 --- a/include/configs/W7OLMC.h +++ b/include/configs/W7OLMC.h @@ -125,6 +125,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 384000 diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h index be8c9f8..f12fa55 100644 --- a/include/configs/W7OLMG.h +++ b/include/configs/W7OLMG.h @@ -133,6 +133,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 384000 diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h index be9ac62..34a5fff 100644 --- a/include/configs/WUH405.h +++ b/include/configs/WUH405.h @@ -122,9 +122,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -332,12 +337,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x40000550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40000550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 #define CONFIG_SYS_DUART_RST (0x80000000 >> 14) diff --git a/include/configs/XPEDITE1000.h b/include/configs/XPEDITE1000.h index dfeaf74..8b47862 100644 --- a/include/configs/XPEDITE1000.h +++ b/include/configs/XPEDITE1000.h @@ -54,7 +54,6 @@ #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) @@ -111,6 +110,12 @@ extern void out32(unsigned int, unsigned long); /* * Serial Port */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/acadia.h b/include/configs/acadia.h index 8b01c70..39f85ae 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -89,6 +89,7 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/aev.h b/include/configs/aev.h index 98958a6..54e6c57 100644 --- a/include/configs/aev.h +++ b/include/configs/aev.h @@ -286,10 +286,11 @@ * Ethernet configuration */ #define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 /* - * Define CONFIG_FEC_10MBIT to force FEC at 10Mb + * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb */ -/* #define CONFIG_FEC_10MBIT 1 */ +/* #define CONFIG_MPC5xxx_FEC_MII10 */ #define CONFIG_PHY_ADDR 0x00 /* diff --git a/include/configs/alpr.h b/include/configs/alpr.h index 326b324..7038291 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -45,7 +45,6 @@ #define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 @@ -74,9 +73,14 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 -#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h index 23a859f..9c53d37 100644 --- a/include/configs/amcc-common.h +++ b/include/configs/amcc-common.h @@ -31,8 +31,12 @@ /* * UART */ -#define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() +#define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} diff --git a/include/configs/aria.h b/include/configs/aria.h index c5f9cc1..c5a3feb 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -321,7 +321,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO /* * Serial console configuration @@ -507,10 +506,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Cache Configuration */ #define CONFIG_SYS_DCACHE_SIZE 32768 diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 8c4127d..18276c5 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -62,8 +62,7 @@ #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ /*Don't change either of these*/ #define CONFIG_SYS_USB_DEVICE 0x50000000 @@ -85,9 +84,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -/* define this if you want console on UART1 */ -#undef CONFIG_UART1_CONSOLE /*----------------------------------------------------------------------- * NVRAM/RTC diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index 627060a..3e64492 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -123,7 +123,7 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 @@ -179,6 +179,7 @@ * (Set up by the startup code) */ #define CONFIG_SYS_SRAM_BASE 0xFFF00000 +#define CONFIG_SYS_SRAM_SIZE (256 << 10) #define CONFIG_SYS_FLASH_BASE 0xFFF80000 /*----------------------------------------------------------------------- @@ -283,12 +284,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x55555555 -#define CONFIG_SYS_GPIO0_OSRL 0x40000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x55555555 +#define CONFIG_SYS_GPIO0_OSRH 0x40000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xFFFF8014 /*----------------------------------------------------------------------- diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 6fe7639..51087f7 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -111,10 +111,9 @@ #define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */ #define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ +#define CONFIG_SYS_SRAM_SIZE (256 << 10) #define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 -#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals */ - #define CONFIG_SYS_AHB_BASE 0xE2000000 /* internal AHB peripherals */ /*----------------------------------------------------------------------- @@ -129,7 +128,7 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/csb272.h b/include/configs/csb272.h index 9ded330..7108210 100644 --- a/include/configs/csb272.h +++ b/include/configs/csb272.h @@ -160,6 +160,12 @@ * UART configuration * */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #define CONFIG_SYS_EXT_SERIAL_CLOCK 3868400 /* use external serial clock */ #undef CONFIG_SYS_BASE_BAUD #define CONFIG_BAUDRATE 38400 /* Default baud rate */ diff --git a/include/configs/csb472.h b/include/configs/csb472.h index 71eb083..7b9f29a 100644 --- a/include/configs/csb472.h +++ b/include/configs/csb472.h @@ -159,6 +159,12 @@ * UART configuration * */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* use internal serial clock */ #define CONFIG_SYS_BASE_BAUD 691200 #define CONFIG_BAUDRATE 38400 /* Default baud rate */ diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 357715d..d02b196 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -39,7 +39,6 @@ #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) #define CONFIG_SYS_HZ 1000 #define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ /* * Memory Info @@ -48,6 +47,7 @@ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */ #define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ #define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ /* memtest start addr */ #define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) @@ -137,4 +137,9 @@ #undef CONFIG_CMD_ENV #endif +/* additions for new relocation code, must added to all boards */ +#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ + CONFIG_SYS_GBL_DATA_SIZE) #endif /* __CONFIG_H */ diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h index 875dda4..04cdc21 100644 --- a/include/configs/davinci_schmoogie.h +++ b/include/configs/davinci_schmoogie.h @@ -99,7 +99,6 @@ /*=====================*/ #define CONFIG_RTC_DS1307 /* RTC chip on SCHMOOGIE */ #define CONFIG_SYS_I2C_RTC_ADDR 0x6f /* RTC chip I2C address */ -#define CONFIG_HAS_UID #define CONFIG_UID_DS28CM00 /* Unique ID on SCHMOOGIE */ #define CONFIG_SYS_UID_ADDR 0x50 /* UID chip I2C address */ /*==============================*/ diff --git a/include/configs/dlvision.h b/include/configs/dlvision.h index 4533799..21d2d28 100644 --- a/include/configs/dlvision.h +++ b/include/configs/dlvision.h @@ -97,7 +97,7 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/eNET.h b/include/configs/eNET.h index 361fe61..da2a97d 100644 --- a/include/configs/eNET.h +++ b/include/configs/eNET.h @@ -59,7 +59,6 @@ * Serial Configuration */ #define CONFIG_SERIAL_MULTI -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL diff --git a/include/configs/ebony.h b/include/configs/ebony.h index 10f425d..8c3284a 100644 --- a/include/configs/ebony.h +++ b/include/configs/ebony.h @@ -61,7 +61,6 @@ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -81,7 +80,7 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ /*----------------------------------------------------------------------- diff --git a/include/configs/gdppc440etx.h b/include/configs/gdppc440etx.h index d193919..d6db7bf 100644 --- a/include/configs/gdppc440etx.h +++ b/include/configs/gdppc440etx.h @@ -59,7 +59,6 @@ #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripheral*/ #define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs */ /*Don't change either of these*/ @@ -80,8 +79,12 @@ /* * Serial Port */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_UART1_CONSOLE /* * Environment diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h index 5adcc0f..f2ab50c 100644 --- a/include/configs/hcu5.h +++ b/include/configs/hcu5.h @@ -70,9 +70,6 @@ #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 -/* Don't change either of these */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ - #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 @@ -93,8 +90,6 @@ *----------------------------------------------------------------------*/ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_BAUDRATE 115200 -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#undef CONFIG_UART1_CONSOLE /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/icon.h b/include/configs/icon.h index eb419eb..ad0ca5d 100644 --- a/include/configs/icon.h +++ b/include/configs/icon.h @@ -52,7 +52,6 @@ * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_FLASH_BASE 0xfc000000 /* later mapped to this addr */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ @@ -105,7 +104,7 @@ /* * Serial Port */ -#undef CONFIG_UART1_CONSOLE +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* diff --git a/include/configs/imx27lite-common.h b/include/configs/imx27lite-common.h index 1da8602..812e5f2 100644 --- a/include/configs/imx27lite-common.h +++ b/include/configs/imx27lite-common.h @@ -188,6 +188,7 @@ */ #include <config_cmd_default.h> #define CONFIG_CMD_ASKENV +#define CONFIG_CMD_CACHE #define CONFIG_CMD_DHCP #define CONFIG_CMD_DIAG #define CONFIG_CMD_FAT @@ -234,4 +235,9 @@ "mtdids=" MTDIDS_DEFAULT "\0" \ "mtdparts=" MTDPARTS_DEFAULT "\0" \ +/* additions for new relocation code, must added to all boards */ +#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ + CONFIG_SYS_GBL_DATA_SIZE) #endif /* __IMX27LITE_COMMON_CONFIG_H */ diff --git a/include/configs/intip.h b/include/configs/intip.h index 19f12fa..82c8282 100644 --- a/include/configs/intip.h +++ b/include/configs/intip.h @@ -93,10 +93,9 @@ #define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */ #define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ +#define CONFIG_SYS_SRAM_SIZE (256 << 10) #define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 -#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal periph. */ - #define CONFIG_SYS_AHB_BASE 0xE2000000 /* int. AHB periph. */ /* @@ -112,7 +111,7 @@ /* * Serial Port */ -#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ /* * Environment diff --git a/include/configs/jadecpu.h b/include/configs/jadecpu.h index 29c534c..a5d8764 100644 --- a/include/configs/jadecpu.h +++ b/include/configs/jadecpu.h @@ -146,6 +146,9 @@ #define PHYS_SDRAM 0x40000000 /* Start address of DDRRAM */ #define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_SP_ADDR 0x01008000 + /* * FLASH and environment organization */ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 5d14a10..e4ccd7d 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -61,7 +61,6 @@ * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ @@ -104,7 +103,7 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_UART1_CONSOLE +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /*----------------------------------------------------------------------- diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 8f813dd0..37eaf8f 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -57,7 +57,6 @@ #define CONFIG_SYS_FLASH_BASE 0xFC000000 #define CONFIG_SYS_NAND_ADDR 0xF8000000 #define CONFIG_SYS_FPGA_BASE 0xF0000000 -#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -114,8 +113,7 @@ * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -/* define this if you want console on UART1 */ -#undef CONFIG_UART1_CONSOLE +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/km_arm.h b/include/configs/km_arm.h index 1617e69..8673e6f 100644 --- a/include/configs/km_arm.h +++ b/include/configs/km_arm.h @@ -180,4 +180,8 @@ int get_scl (void); #undef CONFIG_JFFS2_CMDLINE #endif +/* additions for new relocation code, must added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_INIT_SP_ADDR (0x00000000 + 0x1000 - /* Fix this */ \ + CONFIG_SYS_GBL_DATA_SIZE) #endif /* _CONFIG_KM_ARM_H */ diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index f7d36b1..4794256 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -257,7 +257,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -358,10 +357,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup diff --git a/include/configs/korat.h b/include/configs/korat.h index 23da72f..55ef4f0 100644 --- a/include/configs/korat.h +++ b/include/configs/korat.h @@ -71,9 +71,6 @@ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE + 0x20000000) -/* Don't change either of these */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ - #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 @@ -93,11 +90,14 @@ /* * Serial Port */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI 1 -/* define this if you want console on UART1 */ -#undef CONFIG_UART1_CONSOLE #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} diff --git a/include/configs/luan.h b/include/configs/luan.h index b158b74..6b1a41f 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -53,12 +53,11 @@ #define CONFIG_SYS_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */ #define CONFIG_SYS_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */ #define CONFIG_SYS_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */ +#define CONFIG_SYS_SRAM_SIZE (1 << 20) #define CONFIG_SYS_EPLD_BASE 0xff000000 /* EPLD and FRAM CS1 */ #define CONFIG_SYS_ISRAM_BASE 0xf8000000 /* internal 8k SRAM (L2 cache) */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xf0000000 /* internal peripherals */ - #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ @@ -87,8 +86,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */ -#undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */ /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 295a18e..72e02f8 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -62,9 +62,6 @@ #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 -/* Don't change either of these */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ - #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 @@ -106,11 +103,14 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */ #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI 1 -/* define this if you want console on UART1 */ -#define CONFIG_UART1_CONSOLE 1 /* use UART1 as console */ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} diff --git a/include/configs/makalu.h b/include/configs/makalu.h index f24d499..905c719 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -55,7 +55,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_BASE 0xFC000000 #define CONFIG_SYS_FPGA_BASE 0xF0000000 -#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -111,9 +110,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no ext. clk */ -/* define this if you want console on UART1 */ -#undef CONFIG_UART1_CONSOLE /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h index 50bed10..3e04cfe 100644 --- a/include/configs/mcu25.h +++ b/include/configs/mcu25.h @@ -86,16 +86,9 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO - /* Set console baudrate to 9600 */ #define CONFIG_BAUDRATE 9600 diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h index 92c4f5f..a26de0b 100644 --- a/include/configs/mecp5123.h +++ b/include/configs/mecp5123.h @@ -218,7 +218,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO /* * Serial console configuration @@ -344,10 +343,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory map */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Linux initial memory map */ /* Cache Configuration */ #define CONFIG_SYS_DCACHE_SIZE 32768 diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h index 5281042..3740316 100644 --- a/include/configs/mpc5121ads.h +++ b/include/configs/mpc5121ads.h @@ -47,14 +47,16 @@ #define CONFIG_E300 1 /* E300 Family */ #define CONFIG_MPC512X 1 /* MPC512X family */ #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ -#undef CONFIG_FSL_DIU_LOGO_BMP /* Don't include FSL DIU binary bmp */ /* video */ #undef CONFIG_VIDEO -#if defined(CONFIG_VIDEO) +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP #define CONFIG_CFB_CONSOLE #define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO #endif /* CONFIG_PCI is defined at config time */ @@ -284,7 +286,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO /* * Serial console configuration @@ -477,10 +478,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ /* Cache Configuration */ #define CONFIG_SYS_DCACHE_SIZE 32768 diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h new file mode 100644 index 0000000..b5a19e4 --- /dev/null +++ b/include/configs/mpc8308_p1m.h @@ -0,0 +1,555 @@ +/* + * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. + * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83xx 1 /* MPC83xx family */ +#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ +#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */ + +/* + * On-board devices + * + * TSECs + */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC2 + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.66MHz, then + * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz + * We choose the A type silicon as default, so the core is 400Mhz. + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_CORE_TO_CSB_3X1) +/* + * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits + * in 8308's HRCWH according to the manual, but original Freescale's + * code has them and I've expirienced some problems using the board + * with BDI3000 attached when I've tried to set these bits to zero + * (UART doesn't work after the 'reset run' command). + */ +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_MII |\ + HRCWH_TSEC2M_IN_MII |\ + HRCWH_BIG_ENDIAN) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH (\ + SICRH_ESDHC_A_GPIO |\ + SICRH_ESDHC_B_GPIO |\ + SICRH_ESDHC_C_GTM |\ + SICRH_GPIO_A_TSEC2 |\ + SICRH_GPIO_B_TSEC2_TX_CLK |\ + SICRH_IEEE1588_A_GPIO |\ + SICRH_USB |\ + SICRH_GTM_GPIO |\ + SICRH_IEEE1588_B_GPIO |\ + SICRH_ETSEC2_CRS |\ + SICRH_GPIOSEL_1 |\ + SICRH_TMROBI_V3P3 |\ + SICRH_TSOBI1_V3P3 |\ + SICRH_TSOBI2_V3P3) /* 0xf577d100 */ +#define CONFIG_SYS_SICRL (\ + SICRL_SPI_PF0 |\ + SICRL_UART_PF0 |\ + SICRL_IRQ_PF0 |\ + SICRL_I2C2_PF0 |\ + SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ + +#define CONFIG_SYS_GPIO1_PRELIM +/* GPIO Default input/output settings */ +#define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00 +/* + * Default GPIO values: + * LED#1 enabled; WLAN enabled; Both COM LED on (orange) + */ +#define CONFIG_SYS_GPIO1_DAT 0x08008C00 + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * SERDES + */ +#define CONFIG_FSL_SERDES +#define CONFIG_FSL_SERDES1 0xe3000 + +/* + * Arbiter Setup + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of two chips HY5PS12621BFP-C4 from HYNIX + */ + +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ + +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | 0x00010000 /* ODT_WR to CSn */ \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00220802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (5 << TIMING_CFG1_CASLAT_SHIFT) \ + | (6 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x27256222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (4 << TIMING_CFG2_CPO_SHIFT) \ + | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x121048c5 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x03600100 */ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_32_BE) + /* 0x43080000 */ + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0232 << SDRAM_MODE_SD_SHIFT)) + /* ODT 150ohm CL=3, AL=1 on SDRAM */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x07f00000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ + +/* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) + +#define CONFIG_SYS_BR0_PRELIM (\ + CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\ + (2 << BR_PS_SHIFT) /* 16 bit port size */ |\ + BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_4 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 + +/* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024) +/* Flash Write Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024) + +/* + * SJA1000 CAN controller on Local Bus + */ +#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000 +#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \ + | (1 << BR_PS_SHIFT) /* 8 bit port size */ \ + | BR_V ) /* valid */ +#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ + | OR_GPCM_SCY_5 \ + | OR_GPCM_EHTR) + /* 0xFFFF8052 */ + +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) + +/* + * CPLD on Local Bus + */ +#define CONFIG_SYS_CPLD_BASE 0xFBFF8000 +#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \ + | (1 << BR_PS_SHIFT) /* 8 bit port size */ \ + | BR_V ) /* valid */ +#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \ + | OR_GPCM_SCY_4 \ + | OR_GPCM_EHTR) + /* 0xFFFF8042 */ + +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE +#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_FSL_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +/* enable PCIE clock */ +#define CONFIG_SYS_SCCR_PCIEXP1CM 1 + +#define CONFIG_PCI +#define CONFIG_PCIE + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 + +/* + * TSEC + */ +#define CONFIG_NET_MULTI +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 1 +#define TSEC2_PHY_ADDR 2 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS 0 +#define TSEC2_FLAGS 0 + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC0" + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ + BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define xstr(s) str(s) +#define str(s) #s + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=${consoledev},${baudrate}\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "addmisc=setenv bootargs ${bootargs}\0" \ + "kernel_addr=FC0A0000\0" \ + "fdt_addr=FC2A0000\0" \ + "ramdisk_addr=FC2C0000\0" \ + "u-boot=mpc8308_p1m/u-boot.bin\0" \ + "kernel_addr_r=1000000\0" \ + "fdt_addr_r=C00000\0" \ + "hostname=mpc8308_p1m\0" \ + "bootfile=mpc8308_p1m/uImage\0" \ + "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \ + "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ + "flash_self=run ramargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdtfile};" \ + "run nfsargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "bootcmd=run flash_self\0" \ + "load=tftp ${loadaddr} ${u-boot}\0" \ + "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};cp.b ${fileaddr} " \ + xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ + "upd=run load update\0" \ + +#endif /* __CONFIG_H */ diff --git a/include/configs/mucmc52.h b/include/configs/mucmc52.h index 07ed046..f87dc9c 100644 --- a/include/configs/mucmc52.h +++ b/include/configs/mucmc52.h @@ -80,6 +80,8 @@ #define CONFIG_SYS_CS1_SIZE 0x00100000 #define CONFIG_SYS_CS1_CFG 0x00019B00 +#define CONFIG_SYS_SRAM_SIZE CONFIG_SYS_CS1_SIZE + /* FRAM 32Kbyte @0x80700000 */ #define CONFIG_SYS_CS2_START 0x80700000 #define CONFIG_SYS_CS2_SIZE 0x00008000 diff --git a/include/configs/neo.h b/include/configs/neo.h index f275c7b..f8f53e8 100644 --- a/include/configs/neo.h +++ b/include/configs/neo.h @@ -98,7 +98,12 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/netstal-common.h b/include/configs/netstal-common.h index cb7efe7..8f42b6c 100644 --- a/include/configs/netstal-common.h +++ b/include/configs/netstal-common.h @@ -34,7 +34,12 @@ /* * UART */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SERIAL_MULTI +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h index 9cb66b7..d11d218 100644 --- a/include/configs/ocotea.h +++ b/include/configs/ocotea.h @@ -58,7 +58,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -80,7 +79,7 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ /*----------------------------------------------------------------------- diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 71553f9..2463be4 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -120,6 +120,7 @@ /* commands to include */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_EXT2 /* EXT2 Support */ #define CONFIG_CMD_FAT /* FAT support */ #define CONFIG_CMD_JFFS2 /* JFFS2 Support */ @@ -339,4 +340,9 @@ extern unsigned int boot_flash_sec; extern unsigned int boot_flash_type; #endif +/* additions for new relocation code, must added to all boards */ +#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h index d6b9207..6edf91e 100644 --- a/include/configs/p3p440.h +++ b/include/configs/p3p440.h @@ -49,7 +49,6 @@ #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -80,6 +79,12 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 1f744b8..85152d1 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -60,7 +60,6 @@ #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ #define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ /*Don't change either of these*/ @@ -80,11 +79,14 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clk used */ #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI 1 -/*define this if you want console on UART1*/ -#undef CONFIG_UART1_CONSOLE #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h index 718abdf..f073fcd 100644 --- a/include/configs/pdm360ng.h +++ b/include/configs/pdm360ng.h @@ -412,11 +412,11 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Cache Configuration */ #define CONFIG_SYS_DCACHE_SIZE 32768 diff --git a/include/configs/qong.h b/include/configs/qong.h index 100fa3f..7a68b7b 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -104,6 +104,7 @@ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_NET @@ -281,4 +282,14 @@ extern int qong_nand_rdy(void *chip); "mtdparts=physmap-flash.0:384k(U-Boot),128k(env1)," \ "128k(env2),2432k(kernel),13m(ramdisk),-(user)" +/* additions for new relocation code, must added to all boards */ +#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_END IRAM_SIZE +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET) + +#define CONFIG_BOARD_EARLY_INIT_F 1 + #endif /* __CONFIG_H */ diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h index 5538b18..0764cc8 100644 --- a/include/configs/quad100hd.h +++ b/include/configs/quad100hd.h @@ -105,6 +105,11 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_SYS_BASE_BAUD 691200 #define CONFIG_BAUDRATE 115200 @@ -270,12 +275,12 @@ * Taken in part from PPCBoot board/icecube/icecube.h */ /* see ./arch/powerpc/cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */ -#define CONFIG_SYS_GPIO0_OSRH 0x55555550 -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x55555550 +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xFFFF8097 #define CONFIG_SYS_GPIO0_ODR 0x00000000 diff --git a/include/configs/redwood.h b/include/configs/redwood.h index 87adbf8..3c1e882 100644 --- a/include/configs/redwood.h +++ b/include/configs/redwood.h @@ -47,7 +47,6 @@ * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -77,6 +76,11 @@ #define CONFIG_SYS_FPGA_BASE 0xe2000000 /* epld */ #define CONFIG_SYS_OPER_FLASH 0xe7000000 /* SRAM - OPER Flash */ +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ + /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h index 429b11c..187002c 100644 --- a/include/configs/sbc405.h +++ b/include/configs/sbc405.h @@ -147,6 +147,12 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index deaddde..b8f4b6e 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -270,7 +270,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -465,10 +464,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 564f661..8d047de 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -338,7 +338,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 53d06ed..6352278 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -203,7 +203,6 @@ #undef CONFIG_CONS_NONE /* define if console on something else */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 618513a..a7831c0 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -257,7 +257,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/sc3.h b/include/configs/sc3.h index 19084ce..278b60e 100644 --- a/include/configs/sc3.h +++ b/include/configs/sc3.h @@ -76,15 +76,12 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SERIAL_MULTI -#undef CONFIG_SERIAL_SOFTWARE_FIFO -/* - * define CONFIG_POWER_DOWN if your cpu should power down while waiting for your input - * Works only, if you have enabled the CONFIG_SERIAL_SOFTWARE_FIFO feature - */ -#if CONFIG_SERIAL_SOFTWARE_FIFO - #define CONFIG_POWER_DOWN -#endif /* * define CONFIG_SYS_CLK_FREQ to your base crystal clock in Hz diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index ee4391f..988d41f 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -84,9 +84,6 @@ #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 -/* Don't change either of these */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ - #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 @@ -105,9 +102,8 @@ /* * Serial Port */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -/* define this if you want console on UART1 */ -#undef CONFIG_UART1_CONSOLE /* * Environment diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h deleted file mode 100644 index 060026b..0000000 --- a/include/configs/smmaco4.h +++ /dev/null @@ -1,379 +0,0 @@ -/* - * (C) Copyright 2003-2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2005 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ -#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ -#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ -#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) - -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SNTP - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (TEXT_BASE == 0xFC000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "bootfile=/tftpboot/smmaco4/uImage\0" \ - "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/smmaco4/u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock - * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. - */ -#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver if no module variant is spezified */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* Dynamic MTD partition support */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=TQM5200-0" -#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ - "1408k(kernel)," \ - "2m(initrd)," \ - "4m(small-fs)," \ - "16m(big-fs)," \ - "8m(misc)" - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE -#endif - - -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -/* - * Define CONFIG_FEC_10MBIT to force FEC at 10Mb - */ -/* #define CONFIG_FEC_10MBIT 1 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 - * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. - * Use for REV200 STK52XX boards. Do not use with REV100 modules - * (because, there I2C1 is used as I2C bus) - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) - * 000 -> All PSC2 pins are GIOPs - * 001 -> CAN1/2 on PSC2 pins - * Use for REV100 STK52xx boards - * use PSC6: - * on STK52xx: - * use as UART. Pins PSC6_0 to PSC6_3 are used. - * Bits 9:11 (mask: 0x00700000): - * 101 -> PSC6 : Extended POST test is not available - * on MINI-FAP and TQM5200_IB: - * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): - * 000 -> PSC6 could not be used as UART, CODEC or IrDA - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. - */ -#if defined (CONFIG_MINIFAP) -# define CONFIG_SYS_GPS_PORT_CONFIG 0x91000004 -#elif defined (CONFIG_STK52XX) -# if defined (CONFIG_STK52XX_REV100) -# define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014 -# else /* STK52xx REV200 and above */ -# if defined (CONFIG_TQM5200_REV100) -# error TQM5200 REV100 not supported on STK52XX REV200 or above -# else/* TQM5200 REV200 and above */ -# define CONFIG_SYS_GPS_PORT_CONFIG 0x91500004 -# endif -# endif -#else /* TMQ5200 Inbetriebnahme-Board */ -# define CONFIG_SYS_GPS_PORT_CONFIG 0x81000004 -#endif - -/* - * RTC configuration - */ -#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 -#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -#endif /* __CONFIG_H */ diff --git a/include/configs/socrates.h b/include/configs/socrates.h index af1e19e..88be349 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -218,7 +218,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 57bb8d1..911c906 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -176,7 +176,6 @@ /* Serial Port */ #define CONFIG_CONS_INDEX 2 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 diff --git a/include/configs/t3corp.h b/include/configs/t3corp.h index b38886b..39ca793 100644 --- a/include/configs/t3corp.h +++ b/include/configs/t3corp.h @@ -86,10 +86,9 @@ #define CONFIG_SYS_OCM_BASE 0xE7000000 /* OCM: 64k */ #define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ +#define CONFIG_SYS_SRAM_SIZE (256 << 10) #define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 -#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal periph. */ - /* * Initial RAM & stack pointer (placed in OCM) */ @@ -103,7 +102,7 @@ /* * Serial Port */ -#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ /* * Environment diff --git a/include/configs/taihu.h b/include/configs/taihu.h index 836081d..7e660ee 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -127,11 +127,10 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_UART1_CONSOLE 1 /*----------------------------------------------------------------------- * I2C stuff diff --git a/include/configs/taishan.h b/include/configs/taishan.h index 394dd8d..faf9e20 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -50,7 +50,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ @@ -76,7 +75,7 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ /*----------------------------------------------------------------------- diff --git a/include/configs/tx25.h b/include/configs/tx25.h index c8188ca..c798570 100644 --- a/include/configs/tx25.h +++ b/include/configs/tx25.h @@ -40,9 +40,9 @@ /* Start copying real U-boot from the second page */ #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x800 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x30000 -/* Load U-Boot to this address */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x81f00000 -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST + +#define CONFIG_SYS_NAND_U_BOOT_DST (0x81fc0000) +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST #define CONFIG_SYS_NAND_PAGE_SIZE 2048 #define CONFIG_SYS_NAND_SPARE_SIZE 64 @@ -52,7 +52,6 @@ #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 #else #define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_SKIP_RELOCATE_UBOOT #endif #define CONFIG_DISPLAY_CPUINFO @@ -131,6 +130,7 @@ /* U-Boot commands */ #include <config_cmd_default.h> #define CONFIG_CMD_NAND +#define CONFIG_CMD_CACHE /* * Ethernet @@ -176,4 +176,10 @@ "update=nand erase 0 40000;nand write ${loadaddr} 0 40000\0" \ "upd=run load update\0" \ +/* additions for new relocation code, must added to all boards */ +#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ + CONFIG_SYS_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/uc101.h b/include/configs/uc101.h index fc0b103..1972261 100644 --- a/include/configs/uc101.h +++ b/include/configs/uc101.h @@ -65,9 +65,7 @@ #define CONFIG_SYS_IB_EPLD 0xc0500000 /* CS 7 */ /* SRAM */ -#define SRAM_BASE CONFIG_SYS_SRAM_BASE -#define SRAM_LEN 0x1fffff -#define SRAM_END (SRAM_BASE + SRAM_LEN) +#define CONFIG_SYS_SRAM_SIZE 0x200000 /* * GPIO configuration diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h index 56d24f9..45976db 100644 --- a/include/configs/ve8313.h +++ b/include/configs/ve8313.h @@ -366,10 +366,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ /* 0x64050000 */ #define CONFIG_SYS_HRCW_LOW (\ diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h index f493e75..f2fb592 100644 --- a/include/configs/vme8349.h +++ b/include/configs/vme8349.h @@ -184,7 +184,6 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -402,10 +401,10 @@ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Init Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/ #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ diff --git a/include/configs/walnut.h b/include/configs/walnut.h index 630c0d3..3be489d 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -84,7 +84,7 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index b66ab58..ed0560a 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -62,7 +62,6 @@ #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ #define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ /*Don't change either of these*/ @@ -84,9 +83,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -/*define this if you want console on UART1*/ -#undef CONFIG_UART1_CONSOLE /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 798c75a..4e64eec 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -60,7 +60,6 @@ * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ @@ -105,9 +104,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_UART1_CONSOLE +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* #define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */ diff --git a/include/configs/zeus.h b/include/configs/zeus.h index 29ada9e..aa250cc 100644 --- a/include/configs/zeus.h +++ b/include/configs/zeus.h @@ -122,14 +122,18 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SYS_BASE_BAUD 691200 +#define CONFIG_SYS_BASE_BAUD 691200 #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /*----------------------------------------------------------------------- * Miscellaneous configurable options @@ -280,12 +284,12 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CONFIG_SYS_GPIO0_OSRH 0x15555550 /* Chip selects */ -#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* UART_DTR-pin 27 alt out */ -#define CONFIG_SYS_GPIO0_ISR1H 0x10000041 /* Pin 2, 12 is input */ -#define CONFIG_SYS_GPIO0_ISR1L 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */ -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x15555550 /* Chip selects */ +#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* UART_DTR-pin 27 alt out */ +#define CONFIG_SYS_GPIO0_ISR1L 0x10000041 /* Pin 2, 12 is input */ +#define CONFIG_SYS_GPIO0_ISR1H 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */ #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */ #define CONFIG_SYS_GPIO0_ODR 0x00000000 |