diff options
Diffstat (limited to 'include/configs')
64 files changed, 2271 insertions, 530 deletions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 9e0ee37..0718c85 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -53,9 +53,13 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ @@ -144,39 +148,16 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 -#define CFG_NAND_LEGACY - -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ /*----------------------------------------------------------------------- diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h index 08ef9b5..1fd2b53 100644 --- a/include/configs/CMS700.h +++ b/include/configs/CMS700.h @@ -90,8 +90,6 @@ #define CONFIG_CMD_EEPROM -#define CFG_NAND_LEGACY - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ @@ -157,34 +155,15 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 + +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index 0a4e1e9..1b948f6 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -92,8 +92,6 @@ #define CONFIG_SUPPORT_VFAT -#define CFG_NAND_LEGACY - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index ceeba6e..fb71c5f 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -114,8 +114,6 @@ #define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */ #endif -#define CFG_NAND_LEGACY - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 1aefbba..4994319 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -100,9 +100,6 @@ #define CONFIG_SUPPORT_VFAT -#define CFG_NAND_LEGACY - - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index e2652e6..29f9292 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -111,8 +111,6 @@ #undef CONFIG_AUTO_UPDATE /* autoupdate via compactflash */ -#define CFG_NAND_LEGACY - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ diff --git a/include/configs/EB+MCF-EV123.h b/include/configs/EB+MCF-EV123.h index a8697ec..dae5295 100644 --- a/include/configs/EB+MCF-EV123.h +++ b/include/configs/EB+MCF-EV123.h @@ -40,9 +40,8 @@ #define CONFIG_MISC_INIT_R -#define FEC_ENET -#define CONFIG_ETHADDR 00:CF:52:82:EB:01 - +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 9600 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } @@ -84,7 +83,39 @@ #include <config_cmd_default.h> #undef CONFIG_CMD_LOADB +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET + +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:CF:52:82:EB:01 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* CONFIG_MCFFEC */ #define CONFIG_BOOTDELAY 5 #define CFG_PROMPT "\nEV123 U-Boot> " @@ -122,9 +153,6 @@ */ #define CFG_MBAR 0x40000000 -#define CFG_DISCOVER_PHY -/* #define CFG_ENET_BD_BASE 0x380000 */ - /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ @@ -151,6 +179,7 @@ #define CFG_FLASH_BASE 0xFFE00000 #define CFG_INT_FLASH_BASE 0xF0000000 +#define CFG_INT_FLASH_ENABLE 0x21 /* If M5282 port is fully implemented the monitor base will be behind * the vector table. */ diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 00f481c..ea8e61a 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -141,8 +141,6 @@ #define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */ #undef CONFIG_AUTO_UPDATE_SHOW /* use board show routine */ -#define CFG_NAND_LEGACY - #undef CONFIG_BZIP2 /* include support for bzip2 compressed images */ #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -209,34 +207,15 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 + +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h index 661b895..ed669c5 100644 --- a/include/configs/HUB405.h +++ b/include/configs/HUB405.h @@ -147,36 +147,15 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ -#define CFG_NAND_LEGACY - -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 + +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index 53261548..4c16d22 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -178,12 +178,9 @@ #endif /* CONFIG_MPC5200 */ /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,5200@0" #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 4) diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h new file mode 100644 index 0000000..7f544c8 --- /dev/null +++ b/include/configs/M5235EVB.h @@ -0,0 +1,261 @@ +/* + * Configuation settings for the Freescale MCF5329 FireEngine board. + * + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * TsiChung Liew (Tsi-Chung.Liew@freescale.com) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _M5235EVB_H +#define _M5235EVB_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCF523x /* define processor family */ +#define CONFIG_M5235 /* define processor type */ + +#undef DEBUG + +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG +#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Command line configuration */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BOOTD +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_LOADS + +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C /* I2C with hw support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 80000 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_OFFSET 0x00000300 +#define CFG_IMMR CFG_MBAR + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ +#define CONFIG_BOOTFILE "u-boot.bin" +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* FEC_ENET */ + +#define CONFIG_HOSTNAME M5235EVB +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe3ffff;" \ + "era ffe00000 ffe3ffff;" \ + "cp.b ${loadaddr} ffe00000 ${filesize};"\ + "save\0" \ + "" + +#define CONFIG_PRAM 512 /* 512 KB */ +#define CFG_PROMPT "-> " +#define CFG_LONGHELP /* undef to save memory */ + +#if defined(CONFIG_KGDB) +# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR (CFG_SDRAM_BASE+0x20000) + +#define CFG_HZ 1000 +#define CFG_CLK 75000000 +#define CFG_CPU_CLK CFG_CLK * 2 + +#define CFG_MBAR 0x40000000 + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x20000000 +#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ +#define CFG_INIT_RAM_CTRL 0x21 +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE - 0x10) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ + +#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400 +#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20) + +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ + +#define CFG_BOOTPARAMS_LEN 64*1024 +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +/* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_FLASH_CFI +#ifdef CFG_FLASH_CFI +# define CFG_FLASH_CFI_DRIVER 1 +# define CFG_FLASH_SIZE 0x800000 /* Max size that the board might have */ +#ifdef NORFLASH_PS32BIT +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_32BIT +#else +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#endif +# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +#endif + +#define CFG_FLASH_BASE (CFG_CS0_BASE << 16) + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_IS_EMBEDDED 1 +#ifdef NORFLASH_PS32BIT +# define CFG_ENV_OFFSET (0x8000) +# define CFG_ENV_SIZE 0x4000 +# define CFG_ENV_SECT_SIZE 0x4000 +#else +# define CFG_ENV_OFFSET (0x4000) +# define CFG_ENV_SIZE 0x2000 +# define CFG_ENV_SECT_SIZE 0x2000 +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 + +/*----------------------------------------------------------------------- + * Chipselect bank definitions + */ +/* + * CS0 - NOR Flash 1, 2, 4, or 8MB + * CS1 - Available + * CS2 - Available + * CS3 - Available + * CS4 - Available + * CS5 - Available + * CS6 - Available + * CS7 - Available + */ +#ifdef NORFLASH_PS32BIT +# define CFG_CS0_BASE 0xFFC0 +# define CFG_CS0_MASK 0x003f0001 +# define CFG_CS0_CTRL 0x1D00 +#else +# define CFG_CS0_BASE 0xFFE0 +# define CFG_CS0_MASK 0x001f0001 +# define CFG_CS0_CTRL 0x1D80 +#endif + +#endif /* _M5329EVB_H */ diff --git a/include/configs/M5249EVB.h b/include/configs/M5249EVB.h new file mode 100644 index 0000000..de7ea42 --- /dev/null +++ b/include/configs/M5249EVB.h @@ -0,0 +1,194 @@ +/* + * Configuation settings for the esd TASREG board. + * + * (C) Copyright 2004 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _M5249EVB_H +#define _M5249EVB_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5249 /* define processor type */ + +#define CONFIG_MCFTMR + +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) +#define CONFIG_BAUDRATE 19200 +#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG + +#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */ + +/* + * BOOTP options + */ +#undef CONFIG_BOOTP_BOOTFILESIZE +#undef CONFIG_BOOTP_BOOTPATH +#undef CONFIG_BOOTP_GATEWAY +#undef CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_NET + +#define CFG_PROMPT "=> " +#define CFG_LONGHELP /* undef to save memory */ + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ + +#define CFG_LOAD_ADDR 0x200000 /* default load address */ + +#define CFG_MEMTEST_START 0x400 +#define CFG_MEMTEST_END 0x380000 + +#define CFG_HZ 1000 + +/* + * Clock configuration: enable only one of the following options + */ + +#undef CFG_PLL_BYPASS /* bypass PLL for test purpose */ +#define CFG_FAST_CLK 1 /* MCF5249 can run at 140MHz */ +#define CFG_CLK 132025600 /* MCF5249 can run at 140MHz */ + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CFG_MBAR 0x10000000 /* Register Base Addrs */ +#define CFG_MBAR2 0x80000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x20000000 +#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x4000 /* Address of Environment Sector*/ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x2000 /* see README - env sector total size */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_FLASH_BASE (CFG_CSAR0 << 16) + +#if 0 /* test-only */ +#define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */ +#endif + +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) + +#define CFG_MONITOR_LEN 0x20000 +#define CFG_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */ +#define CFG_BOOTPARAMS_LEN 64*1024 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_FLASH_CFI +#ifdef CFG_FLASH_CFI + +# define CFG_FLASH_CFI_DRIVER 1 +# define CFG_FLASH_SIZE 0x1000000 /* Max size that the board might have */ +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +# define CFG_FLASH_CHECKSUM +# define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 + +/*----------------------------------------------------------------------- + * Memory bank definitions + */ + +/* CS0 - AMD Flash, address 0xffc00000 */ +#define CFG_CSAR0 0xffe0 +#define CFG_CSCR0 0x1980 /* WS=0110, AA=1, PS=10 */ +/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/ +#define CFG_CSMR0 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */ + +/* CS1 - FPGA, address 0xe0000000 */ +#define CFG_CSAR1 0xe000 +#define CFG_CSCR1 0x0d80 /* WS=0011, AA=1, PS=10 */ +#define CFG_CSMR1 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/ + +/*----------------------------------------------------------------------- + * Port configuration + */ +#define CFG_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ +#define CFG_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/ +#define CFG_GPIO_EN 0x00000008 /* Set gpio output enable */ +#define CFG_GPIO1_EN 0x00c70000 /* Set gpio output enable */ +#define CFG_GPIO_OUT 0x00000008 /* Set outputs to default state */ +#define CFG_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ +#define CFG_GPIO1_LED 0x00400000 /* user led */ + +#endif /* M5249 */ diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h new file mode 100644 index 0000000..48170e7 --- /dev/null +++ b/include/configs/M5253EVBE.h @@ -0,0 +1,212 @@ +/* + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * Hayden Fraser (Hayden.Fraser@freescale.com) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _M5253EVBE_H +#define _M5253EVBE_H + +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5253 /* define processor type */ +#define CONFIG_M5253EVBE /* define board type */ + +#define CONFIG_MCFTMR + +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) +#define CONFIG_BAUDRATE 19200 +#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG /* disable watchdog */ + +#define CONFIG_BOOTDELAY 5 + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ +#ifndef CONFIG_MONITOR_IS_IN_RAM +#define CFG_ENV_OFFSET 0x4000 +#define CFG_ENV_SECT_SIZE 0x2000 +#define CFG_ENV_IS_IN_FLASH 1 +#else +#define CFG_ENV_ADDR 0xffe04000 +#define CFG_ENV_SECT_SIZE 0x2000 +#define CFG_ENV_IS_IN_FLASH 1 +#endif + +/* + * BOOTP options + */ +#undef CONFIG_BOOTP_BOOTFILESIZE +#undef CONFIG_BOOTP_BOOTPATH +#undef CONFIG_BOOTP_GATEWAY +#undef CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_NET +#define CONFIG_CMD_LOADB +#define CONFIG_CMD_LOADS +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_IDE +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC + +/* ATA */ +#define CONFIG_DOS_PARTITION +#define CONFIG_MAC_PARTITION +#define CONFIG_IDE_RESET 1 +#define CONFIG_IDE_PREINIT 1 +#define CONFIG_ATAPI +#undef CONFIG_LBA48 + +#define CFG_IDE_MAXBUS 1 +#define CFG_IDE_MAXDEVICE 2 + +#define CFG_ATA_BASE_ADDR (CFG_MBAR2 + 0x800) +#define CFG_ATA_IDE0_OFFSET 0 + +#define CFG_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ +#define CFG_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ +#define CFG_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ +#define CFG_ATA_STRIDE 4 /* Interval between registers */ +#define _IO_BASE 0 + +#define CFG_PROMPT "=> " +#define CFG_LONGHELP /* undef to save memory */ + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_LOAD_ADDR 0x00100000 + +#define CFG_MEMTEST_START 0x400 +#define CFG_MEMTEST_END 0x380000 + +#define CFG_HZ 1000 + +#undef CFG_PLL_BYPASS /* bypass PLL for test purpose */ +#define CFG_FAST_CLK +#ifdef CFG_FAST_CLK +# define CFG_PLLCR 0x1243E054 +# define CFG_CLK 140000000 +#else +# define CFG_PLLCR 0x135a4140 +# define CFG_CLK 70000000 +#endif + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CFG_MBAR 0x10000000 /* Register Base Addrs */ +#define CFG_MBAR2 0x80000000 /* Module Base Addrs 2 */ + +/* + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x20000000 +#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ + +#ifdef CONFIG_MONITOR_IS_IN_RAM +#define CFG_MONITOR_BASE 0x20000 +#else +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#endif + +#define CFG_MONITOR_LEN 0x40000 +#define CFG_MALLOC_LEN (256 << 10) +#define CFG_BOOTPARAMS_LEN (64*1024) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) + +/* FLASH organization */ +#define CFG_FLASH_BASE 0xffe00000 +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ +#define CFG_FLASH_ERASE_TOUT 1000 + +#define CFG_FLASH_CFI 1 +#define CFG_FLASH_CFI_DRIVER 1 +#define CFG_FLASH_SIZE 0x200000 +#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +/* Cache Configuration */ +#define CFG_CACHELINE_SIZE 16 + +/* Port configuration */ +#define CFG_FECI2C 0xF0 + +#define CFG_CSAR0 0xFFE0 +#define CFG_CSMR0 0x001F0021 +#define CFG_CSCR0 0x1D80 + +#define CFG_CSAR1 0 +#define CFG_CSMR1 0 +#define CFG_CSCR1 0 + +#define CFG_CSAR2 0 +#define CFG_CSMR2 0 +#define CFG_CSCR2 0 + +#define CFG_CSAR3 0 +#define CFG_CSMR3 0 +#define CFG_CSCR3 0 + +/*----------------------------------------------------------------------- + * Port configuration + */ +#define CFG_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ +#define CFG_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ +#define CFG_GPIO_EN 0x00000008 /* Set gpio output enable */ +#define CFG_GPIO1_EN 0x00c70000 /* Set gpio output enable */ +#define CFG_GPIO_OUT 0x00000008 /* Set outputs to default state */ +#define CFG_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ +#define CFG_GPIO1_LED 0x00400000 /* user led */ + +#endif /* _M5253EVB_H */ diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h index 885a882..0f97050 100644 --- a/include/configs/M5271EVB.h +++ b/include/configs/M5271EVB.h @@ -31,7 +31,6 @@ #ifndef _M5271EVB_H #define _M5271EVB_H -#define DEBUG #undef DEBUG /* @@ -41,17 +40,15 @@ #define CONFIG_M5271 /* define processor type */ #define CONFIG_M5271EVB /* define board type */ -#define CONFIG_IPADDR 192.168.30.1 -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_ETHADDR 00:06:3b:01:41:55 +#define CONFIG_MCFTMR +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } #undef CONFIG_WATCHDOG /* disable watchdog */ -#define CONFIG_BOOTDELAY 5 - /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */ @@ -73,7 +70,6 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ @@ -81,22 +77,83 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_LOADB +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C /* I2C with hw support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 80000 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_OFFSET 0x00000300 +#define CFG_IMMR CFG_MBAR + +#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ +#define CONFIG_BOOTFILE "u-boot.bin" +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_RETRY_COUNT 5 +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* FEC_ENET */ + +#define CONFIG_HOSTNAME M5235EVB +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe2ffff;" \ + "era ffe00000 ffe2ffff;" \ + "cp.b ${loadaddr} 0 ${filesize};" \ + "save\0" \ + "" #define CFG_PROMPT "=> " -#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_LOAD_ADDR 0x00100000 @@ -114,16 +171,11 @@ #define CFG_MBAR 0x40000000 /* Register Base Addrs */ -/* Enable FEC ethernet */ -#define FEC_ENET -#define CONFIG_NET_RETRY_COUNT 5 -#define CFG_ENET_BD_BASE 0x480000 - /* * Definitions for initial stack pointer and data area (in DPRAM) */ #define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ #define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -134,7 +186,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ #define CFG_FLASH_BASE 0xffe00000 #ifdef CONFIG_MONITOR_IS_IN_RAM @@ -152,11 +204,11 @@ * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) /* FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ #define CFG_FLASH_ERASE_TOUT 1000 #define CFG_FLASH_CFI 1 @@ -169,4 +221,4 @@ /* Port configuration */ #define CFG_FECI2C 0xF0 -#endif /* _M5271EVB_H */ +#endif /* _M5271EVB_H */ diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h index cc456dc..2b8734b 100644 --- a/include/configs/M5272C3.h +++ b/include/configs/M5272C3.h @@ -33,18 +33,20 @@ * High Level Configuration Options * (easy to change) */ -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5272 /* define processor type */ +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5272 /* define processor type */ -#define FEC_ENET +#define CONFIG_MCFTMR +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } -#define CONFIG_WATCHDOG +#undef CONFIG_WATCHDOG #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ -#define CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ +#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash @@ -60,7 +62,6 @@ #define CFG_ENV_IS_IN_FLASH 1 #endif - /* * BOOTP options */ @@ -69,37 +70,82 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_MISC +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_MEMORY #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_LOADB - #define CONFIG_BOOTDELAY 5 +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif + +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* CONFIG_MCFFEC */ + +#define CONFIG_HOSTNAME M5272C3 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe3ffff;" \ + "era ffe00000 ffe3ffff;" \ + "cp.b ${loadaddr} ffe00000 ${filesize};"\ + "save\0" \ + "" #define CFG_PROMPT "-> " -#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_LOAD_ADDR 0x20000 - #define CFG_MEMTEST_START 0x400 #define CFG_MEMTEST_END 0x380000 - #define CFG_HZ 1000 #define CFG_CLK 66000000 @@ -108,20 +154,15 @@ * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ - #define CFG_MBAR 0x10000000 /* Register Base Addrs */ - #define CFG_SCR 0x0003; #define CFG_SPR 0xffff; -#define CFG_DISCOVER_PHY -#define CFG_ENET_BD_BASE 0x380000 - /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ #define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -132,7 +173,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 4 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 4 /* SDRAM size in MB */ #define CFG_FLASH_BASE 0xffe00000 #ifdef CONFIG_MONITOR_IS_IN_RAM @@ -150,13 +191,13 @@ * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ #define CFG_FLASH_ERASE_TOUT 1000 /*----------------------------------------------------------------------- @@ -169,25 +210,18 @@ */ #define CFG_BR0_PRELIM 0xFFE00201 #define CFG_OR0_PRELIM 0xFFE00014 - #define CFG_BR1_PRELIM 0 #define CFG_OR1_PRELIM 0 - #define CFG_BR2_PRELIM 0x30000001 #define CFG_OR2_PRELIM 0xFFF80000 - #define CFG_BR3_PRELIM 0 #define CFG_OR3_PRELIM 0 - #define CFG_BR4_PRELIM 0 #define CFG_OR4_PRELIM 0 - #define CFG_BR5_PRELIM 0 #define CFG_OR5_PRELIM 0 - #define CFG_BR6_PRELIM 0 #define CFG_OR6_PRELIM 0 - #define CFG_BR7_PRELIM 0x00000701 #define CFG_OR7_PRELIM 0xFFC0007C @@ -197,9 +231,8 @@ #define CFG_PACNT 0x00000000 #define CFG_PADDR 0x0000 #define CFG_PADAT 0x0000 -#define CFG_PBCNT 0x55554155 /* Ethernet/UART configuration */ +#define CFG_PBCNT 0x55554155 /* Ethernet/UART configuration */ #define CFG_PBDDR 0x0000 #define CFG_PBDAT 0x0000 #define CFG_PDCNT 0x00000000 - -#endif /* _M5272C3_H */ +#endif /* _M5272C3_H */ diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h index f2a7644..3c17c1e 100644 --- a/include/configs/M5282EVB.h +++ b/include/configs/M5282EVB.h @@ -33,15 +33,17 @@ * High Level Configuration Options * (easy to change) */ -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5282 /* define processor type */ +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5282 /* define processor type */ -#define FEC_ENET +#define CONFIG_MCFTMR +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } -#define CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ +#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash @@ -50,7 +52,6 @@ #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_IS_IN_FLASH 1 - /* * BOOTP options */ @@ -59,29 +60,73 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ #include <config_cmd_default.h> +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_LOADB +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif #define CONFIG_BOOTDELAY 5 +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* CONFIG_MCFFEC */ + +#define CONFIG_HOSTNAME M5272C3 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe3ffff;" \ + "era ffe00000 ffe3ffff;" \ + "cp.b ${loadaddr} ffe00000 ${filesize};"\ + "save\0" \ + "" #define CFG_PROMPT "-> " -#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_LOAD_ADDR 0x20000 @@ -91,6 +136,10 @@ #define CFG_HZ 1000000 #define CFG_CLK 64000000 +/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ + +#define CFG_MFD 0x02 /* PLL Multiplication Factor Devider */ +#define CFG_RFD 0x00 /* PLL Reduce Frecuency Devider */ /* * Low Level Configuration Settings @@ -99,15 +148,12 @@ */ #define CFG_MBAR 0x40000000 -#undef CFG_DISCOVER_PHY -#define CFG_ENET_BD_BASE 0x380000 - /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_INIT_RAM_ADDR 0x20000000 +#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -117,49 +163,88 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 4 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ #define CFG_FLASH_BASE 0xffe00000 #define CFG_INT_FLASH_BASE 0xf0000000 +#define CFG_INT_FLASH_ENABLE 0x21 /* If M5282 port is fully implemented the monitor base will be behind * the vector table. */ -/* #define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) */ -#define CFG_MONITOR_BASE 0x20000 +#if (TEXT_BASE != CFG_INT_FLASH_BASE) +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#else +#define CFG_MONITOR_BASE (TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */ +#endif #define CFG_MONITOR_LEN 0x20000 #define CFG_MALLOC_LEN (256 << 10) #define CFG_BOOTPARAMS_LEN 64*1024 - /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_SECT 35 -#define CFG_MAX_FLASH_BANKS 1 -#define CFG_FLASH_ERASE_TOUT 10000000 +#define CFG_FLASH_CFI +#ifdef CFG_FLASH_CFI + +# define CFG_FLASH_CFI_DRIVER 1 +# define CFG_FLASH_SIZE 0x1000000 /* Max size that the board might have */ +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +# define CFG_FLASH_CHECKSUM +# define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#endif /*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_CACHELINE_SIZE 16 - /*----------------------------------------------------------------------- * Memory bank definitions */ - - +#define CFG_CS0_BASE CFG_FLASH_BASE +#define CFG_CS0_SIZE 2*1024*1024 +#define CFG_CS0_WIDTH 16 +#define CFG_CS0_RO 0 +#define CFG_CS0_WS 6 +/* +#define CFG_CS3_BASE 0xE0000000 +#define CFG_CS3_SIZE 1*1024*1024 +#define CFG_CS3_WIDTH 16 +#define CFG_CS3_RO 0 +#define CFG_CS3_WS 6 +*/ /*----------------------------------------------------------------------- * Port configuration */ +#define CFG_PACNT 0x0000000 /* Port A D[31:24] */ +#define CFG_PADDR 0x0000000 +#define CFG_PADAT 0x0000000 + +#define CFG_PBCNT 0x0000000 /* Port B D[23:16] */ +#define CFG_PBDDR 0x0000000 +#define CFG_PBDAT 0x0000000 + +#define CFG_PCCNT 0x0000000 /* Port C D[15:08] */ +#define CFG_PCDDR 0x0000000 +#define CFG_PCDAT 0x0000000 + +#define CFG_PDCNT 0x0000000 /* Port D D[07:00] */ +#define CFG_PCDDR 0x0000000 +#define CFG_PCDAT 0x0000000 +#define CFG_PEHLPAR 0xC0 +#define CFG_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */ +#define CFG_DDRUA 0x05 +#define CFG_PJPAR 0xFF; -#endif /* _CONFIG_M5282EVB_H */ +#endif /* _CONFIG_M5282EVB_H */ diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h new file mode 100644 index 0000000..d3b1605 --- /dev/null +++ b/include/configs/M5329EVB.h @@ -0,0 +1,267 @@ +/* + * Configuation settings for the Freescale MCF5329 FireEngine board. + * + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * TsiChung Liew (Tsi-Chung.Liew@freescale.com) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _M5329EVB_H +#define _M5329EVB_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCF532x /* define processor family */ +#define CONFIG_M5329 /* define processor type */ + +#undef DEBUG + +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG +#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ + +/* Command line configuration */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#ifdef NANDFLASH_SIZE +# define CONFIG_CMD_NAND +#endif + +#define CFG_UNIFY_CACHE + +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif + +#define CONFIG_MCFRTC +#undef RTC_DEBUG + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C /* I2C with hw support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 80000 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_OFFSET 0x58000 +#define CFG_IMMR CFG_MBAR + +#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ +#define CONFIG_UDP_CHECKSUM + +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* FEC_ENET */ + +#define CONFIG_HOSTNAME M5329EVB +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=40010000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off 0 2ffff;" \ + "era 0 2ffff;" \ + "cp.b ${loadaddr} 0 ${filesize};" \ + "save\0" \ + "" + +#define CONFIG_PRAM 512 /* 512 KB */ +#define CFG_PROMPT "-> " +#define CFG_LONGHELP /* undef to save memory */ + +#ifdef CONFIG_CMD_KGDB +# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x40010000 + +#define CFG_HZ 1000 +#define CFG_CLK 80000000 +#define CFG_CPU_CLK CFG_CLK * 3 + +#define CFG_MBAR 0xFC000000 + +#define CFG_LATCH_ADDR (CFG_CS1_BASE + 0x80000) + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x80000000 +#define CFG_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */ +#define CFG_INIT_RAM_CTRL 0x221 +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 0x10) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x40000000 +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SDRAM_CFG1 0x53722730 +#define CFG_SDRAM_CFG2 0x56670000 +#define CFG_SDRAM_CTRL 0xE1092000 +#define CFG_SDRAM_EMOD 0x40010000 +#define CFG_SDRAM_MODE 0x018D0000 + +#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400 +#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20) + +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ + +#define CFG_BOOTPARAMS_LEN 64*1024 +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_FLASH_CFI +#ifdef CFG_FLASH_CFI +# define CFG_FLASH_CFI_DRIVER 1 +# define CFG_FLASH_SIZE 0x800000 /* Max size that the board might have */ +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +#endif + +#ifdef NANDFLASH_SIZE +# define CFG_MAX_NAND_DEVICE 1 +# define CFG_NAND_BASE (CFG_CS2_BASE << 16) +# define CFG_NAND_SIZE 1 +# define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +# define NAND_MAX_CHIPS 1 +# define NAND_ALLOW_ERASE_ALL 1 +# define CONFIG_JFFS2_NAND 1 +# define CONFIG_JFFS2_DEV "nand0" +# define CONFIG_JFFS2_PART_SIZE (CFG_CS2_MASK & ~1) +# define CONFIG_JFFS2_PART_OFFSET 0x00000000 +#endif + +#define CFG_FLASH_BASE (CFG_CS0_BASE << 16) + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ +#define CFG_ENV_OFFSET 0x4000 +#define CFG_ENV_SECT_SIZE 0x2000 +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_IS_EMBEDDED 1 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 + +/*----------------------------------------------------------------------- + * Chipselect bank definitions + */ +/* + * CS0 - NOR Flash 1, 2, 4, or 8MB + * CS1 - CompactFlash and registers + * CS2 - NAND Flash 16, 32, or 64MB + * CS3 - Available + * CS4 - Available + * CS5 - Available + */ +#define CFG_CS0_BASE 0 +#define CFG_CS0_MASK 0x007f0001 +#define CFG_CS0_CTRL 0x00001fa0 + +#define CFG_CS1_BASE 0x1000 +#define CFG_CS1_MASK 0x001f0001 +#define CFG_CS1_CTRL 0x002A3780 + +#ifdef NANDFLASH_SIZE +#define CFG_CS2_BASE 0x2000 +#define CFG_CS2_MASK ((NANDFLASH_SIZE << 20) | 1) +#define CFG_CS2_CTRL 0x00001f60 +#endif + +#endif /* _M5329EVB_H */ diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h new file mode 100644 index 0000000..6f4859c --- /dev/null +++ b/include/configs/M54455EVB.h @@ -0,0 +1,391 @@ +/* + * Configuation settings for the Freescale MCF54455 EVB board. + * + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * TsiChung Liew (Tsi-Chung.Liew@freescale.com) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _JAMICA54455_H +#define _JAMICA54455_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCF5445x /* define processor family */ +#define CONFIG_M54455 /* define processor type */ +#define CONFIG_M54455EVB /* M54455EVB board */ + +#undef DEBUG + +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Command line configuration */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BOOTD +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_LOADS + +/* Network configuration */ +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CONFIG_CF_DOMII +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC1_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define CFG_FEC1_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +# define CONFIG_HAS_ETH1 + +# define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ +# define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:5M(kernel)ro,-(jffs2)" +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61 +# define CONFIG_ETHPRIME "FEC0" +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE + +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif + +#define CONFIG_HOSTNAME M54455EVB +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "inpclk=" MK_STR(CFG_INPUT_CLKSRC) "\0" \ + "loadaddr=40010000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off 0 2ffff;" \ + "era 0 2ffff;" \ + "cp.b ${loadaddr} 0 ${filesize};" \ + "save\0" \ + "" + +/* ATA configuration */ +#define CONFIG_ISO_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_IDE_RESET 1 +#define CONFIG_IDE_PREINIT 1 +#define CONFIG_ATAPI +#undef CONFIG_LBA48 + +#define CFG_IDE_MAXBUS 1 +#define CFG_IDE_MAXDEVICE 2 + +#define CFG_ATA_BASE_ADDR 0x90000000 +#define CFG_ATA_IDE0_OFFSET 0 + +#define CFG_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ +#define CFG_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ +#define CFG_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ +#define CFG_ATA_STRIDE 4 /* Interval between registers */ +#define _IO_BASE 0 + +/* Realtime clock */ +#define CONFIG_MCFRTC +#undef RTC_DEBUG +#define CFG_RTC_OSCILLATOR (32 * CFG_HZ) + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* I2c */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 80000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_OFFSET 0x58000 +#define CFG_IMMR CFG_MBAR + +/* PCI */ +#define CONFIG_PCI 1 + +#define CFG_PCI_MEM_BUS 0xA0000000 +#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BUS +#define CFG_PCI_MEM_SIZE 0x10000000 + +#define CFG_PCI_IO_BUS 0xB1000000 +#define CFG_PCI_IO_PHYS CFG_PCI_IO_BUS +#define CFG_PCI_IO_SIZE 0x01000000 + +#define CFG_PCI_CFG_BUS 0xB0000000 +#define CFG_PCI_CFG_PHYS CFG_PCI_CFG_BUS +#define CFG_PCI_CFG_SIZE 0x01000000 + +/* FPGA - Spartan 2 */ +/* experiment +#define CONFIG_FPGA CFG_SPARTAN3 +#define CONFIG_FPGA_COUNT 1 +#define CFG_FPGA_PROG_FEEDBACK +#define CFG_FPGA_CHECK_CTRLC +*/ + +/* Input, PCI, Flexbus, and VCO */ +#define CONFIG_EXTRA_CLOCK + +#define CONFIG_PRAM 512 /* 512 KB */ + +#define CFG_PROMPT "-> " +#define CFG_LONGHELP /* undef to save memory */ + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x10000) + +#define CFG_HZ 1000 + +#define CFG_MBAR 0xFC000000 + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x80000000 +#define CFG_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */ +#define CFG_INIT_RAM_CTRL 0x221 +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 16) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x40000000 +#define CFG_SDRAM_BASE1 0x48000000 +#define CFG_SDRAM_SIZE 256 /* SDRAM size in MB */ +#define CFG_SDRAM_CFG1 0x65311610 +#define CFG_SDRAM_CFG2 0x59670000 +#define CFG_SDRAM_CTRL 0xEA0B2000 +#define CFG_SDRAM_EMOD 0x40010000 +#define CFG_SDRAM_MODE 0x00010033 + +#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400 +#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20) + +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CFG_BOOTPARAMS_LEN 64*1024 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +/* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ +#define CFG_ENV_OFFSET 0x4000 +#define CFG_ENV_SECT_SIZE 0x2000 +#define CFG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OVERWRITE 1 +#undef CFG_ENV_IS_EMBEDDED + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#ifdef CFG_ATMEL_BOOT +# define CFG_FLASH_BASE 0 +# define CFG_FLASH0_BASE CFG_CS0_BASE +# define CFG_FLASH1_BASE CFG_CS1_BASE +#else +# define CFG_FLASH_BASE CFG_FLASH0_BASE +# define CFG_FLASH0_BASE CFG_CS1_BASE +# define CFG_FLASH1_BASE CFG_CS0_BASE +#endif + +/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system +/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system + keep reset. */ +#undef CFG_FLASH_CFI +#ifdef CFG_FLASH_CFI + +# define CFG_FLASH_CFI_DRIVER 1 +# define CFG_FLASH_SIZE 0x1000000 /* Max size that the board might have */ +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_8BIT +# define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +# define CFG_FLASH_CHECKSUM +# define CFG_FLASH_BANKS_LIST { CFG_CS0_BASE, CFG_CS1_BASE } + +#else + +# define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ + +# define CFG_ATMEL_REGION 4 +# define CFG_ATMEL_TOTALSECT 11 +# define CFG_ATMEL_SECT {1, 2, 1, 7} +# define CFG_ATMEL_SECTSZ {0x4000, 0x2000, 0x8000, 0x10000} +# define CFG_INTEL_SECT 137 + +/* max number of sectors on one chip */ +# define CFG_MAX_FLASH_SECT (CFG_ATMEL_TOTALSECT + CFG_INTEL_SECT) +# define CFG_FLASH_ERASE_TOUT 2000 /* Atmel needs longer timeout */ +# define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +# define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ +# define CFG_FLASH_UNLOCK_TOUT 100 /* Timeout for Flash Clear Lock Bits (in ms) */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +# define CFG_FLASH_CHECKSUM + +#endif + +/* + * This is setting for JFFS2 support in u-boot. + * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. + */ +#ifdef CFG_ATMEL_BOOT +# define CONFIG_JFFS2_DEV "nor0" +# define CONFIG_JFFS2_PART_SIZE 0x01000000 +# define CONFIG_JFFS2_PART_OFFSET CFG_FLASH1_BASE +#else +# define CONFIG_JFFS2_DEV "nor0" +# define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000) +# define CONFIG_JFFS2_PART_OFFSET (CFG_FLASH0_BASE + 0x500000) +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 + +/*----------------------------------------------------------------------- + * Memory bank definitions + */ +/* + * CS0 - NOR Flash 1, 2, 4, or 8MB + * CS1 - CompactFlash and registers + * CS2 - CPLD + * CS3 - FPGA + * CS4 - Available + * CS5 - Available + */ + +#ifdef CFG_ATMEL_BOOT + /* Atmel Flash */ +#define CFG_CS0_BASE 0 +#define CFG_CS0_MASK 0x00070001 +#define CFG_CS0_CTRL 0x00001140 +/* Intel Flash */ +#define CFG_CS1_BASE 0x04000000 +#define CFG_CS1_MASK 0x01FF0001 +#define CFG_CS1_CTRL 0x003F3D60 + +#define CFG_ATMEL_BASE CFG_CS0_BASE +#else +/* Intel Flash */ +#define CFG_CS0_BASE 0 +#define CFG_CS0_MASK 0x01FF0001 +#define CFG_CS0_CTRL 0x003F3D60 + /* Atmel Flash */ +#define CFG_CS1_BASE 0x04000000 +#define CFG_CS1_MASK 0x00070001 +#define CFG_CS1_CTRL 0x00001140 + +#define CFG_ATMEL_BASE CFG_CS1_BASE +#endif + +/* CPLD */ +#define CFG_CS2_BASE 0x08000000 +#define CFG_CS2_MASK 0x00070001 +#define CFG_CS2_CTRL 0x003f1140 + +/* FPGA */ +#define CFG_CS3_BASE 0x09000000 +#define CFG_CS3_MASK 0x00070001 +#define CFG_CS3_CTRL 0x00000020 + +#endif /* _JAMICA54455_H */ diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 81db96f..6568fe1 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -113,12 +113,12 @@ /* 0x03200064 */ #if defined(CONFIG_DDR_2T_TIMING) #define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \ - | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ | SDRAM_CFG_2T_EN \ | SDRAM_CFG_DBW_32 ) #else #define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \ - | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ | SDRAM_CFG_32_BE ) /* 0x43080000 */ #endif @@ -228,12 +228,9 @@ #define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8313@0" #define OF_SOC "soc8313@e0000000" #define OF_TBCLK (bd->bi_busfreq / 4) @@ -310,6 +307,8 @@ #define CONFIG_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 0x1c #define TSEC2_PHY_ADDR 4 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 @@ -507,6 +506,7 @@ #define CONFIG_ETHADDR 00:E0:0C:00:95:01 #define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH0 #define CONFIG_ETH1ADDR 00:E0:0C:00:95:02 #define CONFIG_IPADDR 10.0.0.2 diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index f62ca2c..c9c6d88 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -30,6 +30,8 @@ #define CONFIG_MPC83XX 1 /* MPC83xx family */ #define CONFIG_MPC832X 1 /* MPC832x CPU specific */ #define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ +#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */ +#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */ /* * System Clock Setup @@ -87,6 +89,7 @@ #define CFG_SICRL 0x00000000 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R /* * IMMR new address @@ -315,12 +318,9 @@ #endif /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8323@0" #define OF_SOC "soc8323@e0000000" #define OF_QE "qe@e0100000" diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 1567fcf..92555ba 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -339,12 +339,9 @@ #endif /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8349@0" #define OF_SOC "soc8349@e0000000" #define OF_TBCLK (bd->bi_busfreq / 4) @@ -440,6 +437,8 @@ #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" @@ -699,6 +698,7 @@ #if defined(CONFIG_TSEC_ENET) #define CONFIG_ETHADDR 00:04:9f:ef:23:33 #define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH0 #define CONFIG_ETH1ADDR 00:E0:0C:00:7E:21 #endif diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 44649d0..54cab52 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -296,12 +296,9 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CFG_NS16550_COM2 (CFG_IMMR + 0x4600) /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8349@0" #define OF_SOC "soc8349@e0000000" #define OF_TBCLK (bd->bi_busfreq / 4) @@ -378,10 +375,12 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CONFIG_TSEC1 #ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 #define CONFIG_TSEC1_NAME "TSEC0" #define CFG_TSEC1_OFFSET 0x24000 #define TSEC1_PHY_ADDR 0x1c /* VSC8201 uses address 0x1c */ #define TSEC1_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT #endif #ifdef CONFIG_TSEC2 @@ -391,6 +390,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CONFIG_UNKNOWN_TSEC /* TSEC2 is proprietary */ #define TSEC2_PHY_ADDR 4 #define TSEC2_PHYIDX 0 +#define TSEC2_FLAGS TSEC_GIGABIT #endif #define CONFIG_ETHPRIME "Freescale TSEC" diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index 4b32a14..41f062c 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -32,6 +32,8 @@ #define CONFIG_MPC83XX 1 /* MPC83XX family */ #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ #define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */ +#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */ +#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */ /* * System Clock Setup @@ -88,6 +90,7 @@ #define CFG_SICRL 0x40000000 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R /* * IMMR new address @@ -309,13 +312,13 @@ /* * CS4 on Local Bus, to PIB */ -#define CFG_BR4_PRELIM 0xf8008801 /* CS4 base address at 0xf8008000 */ +#define CFG_BR4_PRELIM 0xf8010801 /* CS4 base address at 0xf8010000 */ #define CFG_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* * CS5 on Local Bus, to PIB */ -#define CFG_BR5_PRELIM 0xf8010801 /* CS5 base address at 0xf8010000 */ +#define CFG_BR5_PRELIM 0xf8008801 /* CS5 base address at 0xf8008000 */ #define CFG_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* @@ -348,10 +351,6 @@ #define CONFIG_OF_HAS_BD_T 1 #define CONFIG_OF_HAS_UBOOT_ENV 1 - -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8360@0" #define OF_SOC "soc8360@e0000000" #define OF_QE "qe@e0100000" diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 5a7c879..be603ac 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -301,9 +301,6 @@ #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8540@0" #define OF_SOC "soc8540@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) @@ -374,6 +371,8 @@ #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #if CONFIG_HAS_FEC @@ -381,6 +380,7 @@ #define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 +#define FEC_FLAGS 0 #endif /* Options are: TSEC[0-1], FEC */ @@ -489,6 +489,7 @@ /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h index 0ce25cf..e376c11 100644 --- a/include/configs/MPC8540EVAL.h +++ b/include/configs/MPC8540EVAL.h @@ -213,10 +213,13 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_TSEC1 1 +#define CONFIG_HAS_ETH0 #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 +#define CONFIG_HAS_ETH1 #define CONFIG_TSEC2_NAME "TSEC1" #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_HAS_ETH2 #define CONFIG_MPC85XX_FEC_NAME "FEC" #define TSEC1_PHY_ADDR 7 #define TSEC2_PHY_ADDR 4 @@ -224,6 +227,10 @@ #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define FEC_FLAGS 0 + /* Options are: TSEC[0-1], FEC */ #define CONFIG_ETHPRIME "TSEC0" diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 232f171..4e061bd 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -312,9 +312,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8541@0" #define OF_SOC "soc8541@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) @@ -384,13 +381,12 @@ extern unsigned long get_clock_freq(void); #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" -#undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 -#define FEC_PHY_ADDR 3 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define FEC_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" @@ -482,6 +478,7 @@ extern unsigned long get_clock_freq(void); /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 32934e1..f580cca 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -181,6 +181,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */ #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ +#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xf8100000 /* PIXIS registers */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ @@ -252,9 +253,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8544@0" #define OF_SOC "soc8544@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) @@ -282,7 +280,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CFG_PCI1_IO_BASE 0x00000000 #define CFG_PCI1_IO_PHYS 0xe1000000 -#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ +#define CFG_PCI1_IO_SIZE 0x00010000 /* 64k */ /* PCI view of System Memory */ #define CFG_PCI_MEMORY_BUS 0x00000000 @@ -294,27 +292,27 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE #define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */ #define CFG_PCIE2_IO_BASE 0x00000000 -#define CFG_PCIE2_IO_PHYS 0xe2000000 -#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */ +#define CFG_PCIE2_IO_PHYS 0xe1010000 +#define CFG_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 1, Slot 2,tgtid 2, Base address a000 */ #define CFG_PCIE1_MEM_BASE 0xa0000000 #define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE -#define CFG_PCIE1_MEM_SIZE 0x08000000 /* 128M */ -#define CFG_PCIE1_MEM_BASE2 0xa8000000 -#define CFG_PCIE1_MEM_PHYS2 CFG_PCIE1_MEM_BASE2 -#define CFG_PCIE1_MEM_SIZE2 0x04000000 /* 64M */ -#define CFG_PCIE1_IO_BASE 0x00000000 /* reuse mem LAW */ -#define CFG_PCIE1_IO_PHYS 0xaf000000 -#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ +#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCIE1_IO_BASE 0x00000000 +#define CFG_PCIE1_IO_PHYS 0xe1020000 +#define CFG_PCIE1_IO_SIZE 0x00010000 /* 64k */ /* controller 3, direct to uli, tgtid 3, Base address b000 */ #define CFG_PCIE3_MEM_BASE 0xb0000000 #define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE -#define CFG_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCIE3_MEM_SIZE 0x00100000 /* 1M */ #define CFG_PCIE3_IO_BASE 0x00000000 -#define CFG_PCIE3_IO_PHYS 0xe3000000 +#define CFG_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ #define CFG_PCIE3_IO_SIZE 0x00100000 /* 1M */ +#define CFG_PCIE3_MEM_BASE2 0xb0200000 +#define CFG_PCIE3_MEM_PHYS2 CFG_PCIE3_MEM_BASE2 +#define CFG_PCIE3_MEM_SIZE2 0x00200000 /* 1M */ #if defined(CONFIG_PCI) @@ -364,15 +362,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_TSEC1_NAME "eTSEC1" #define CONFIG_TSEC3 1 #define CONFIG_TSEC3_NAME "eTSEC3" -#undef CONFIG_MPC85XX_FEC - -#define CONFIG_TSEC_TBI 1 /* enable internal TBI phy */ -#define CONFIG_SGMII_RISER -#define TSEC1_SGMII_PHY_ADDR_OFFSET 0x1c /* sgmii phy base */ #define TSEC1_PHY_ADDR 0 #define TSEC3_PHY_ADDR 1 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + #define TSEC1_PHYIDX 0 #define TSEC3_PHYIDX 0 @@ -474,6 +470,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:02:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index cda9fd5..6083715 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -336,9 +336,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8548@0" #define OF_SOC "soc8548@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) @@ -447,6 +444,10 @@ extern unsigned long get_clock_freq(void); #define TSEC2_PHYIDX 0 #define TSEC3_PHYIDX 0 #define TSEC4_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) /* Options are: eTSEC[0-3] */ #define CONFIG_ETHPRIME "eTSEC0" @@ -538,6 +539,7 @@ extern unsigned long get_clock_freq(void); /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD @@ -631,7 +633,6 @@ extern unsigned long get_clock_freq(void); #define ENET_ENV "" #endif -#if 0 #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ @@ -644,8 +645,8 @@ extern unsigned long get_clock_freq(void); "consoledev=ttyS1\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=ramdisk.uboot\0" \ - "dtbaddr=c00000\0" \ - "dtbfile=mpc8548cds.dtb\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=mpc8548cds.dtb\0" \ "eoi=mw e00400b0 0\0" \ "iack=md e00400a0 1\0" \ "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \ @@ -667,8 +668,6 @@ extern unsigned long get_clock_freq(void); PCI_ENV1 \ PCI_ENV2 \ ENET_ENV -#endif - #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ @@ -676,8 +675,8 @@ extern unsigned long get_clock_freq(void); "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr - $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ @@ -685,8 +684,8 @@ extern unsigned long get_clock_freq(void); "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr $ramdiskaddr $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index e8fe99a..1d1b7c9 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -312,9 +312,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8555@0" #define OF_SOC "soc8555@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) @@ -384,13 +381,12 @@ extern unsigned long get_clock_freq(void); #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" -#undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 -#define FEC_PHY_ADDR 3 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define FEC_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" @@ -482,6 +478,7 @@ extern unsigned long get_clock_freq(void); /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index c10e551..a8f362f 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -292,9 +292,6 @@ #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8560@0" #define OF_SOC "soc8560@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) @@ -360,11 +357,12 @@ #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" -#undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" @@ -521,6 +519,7 @@ /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index dc9cb1f..ba744e9 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -35,7 +35,7 @@ #define CONFIG_PCI #define CONFIG_TSEC_ENET /* tsec ethernet support */ -#undef CONFIG_QE /* Enable QE */ +#define CONFIG_QE /* Enable QE */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ #define CONFIG_DDR_DLL /* possible DLL fix needed */ @@ -63,9 +63,9 @@ extern unsigned long get_clock_freq(void); /* * These can be toggled for performance analysis, otherwise use default. */ -/*#define CONFIG_L2_CACHE*/ /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ /* * Only possible on E500 Version 2 or newer cores. @@ -293,9 +293,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8568@0" #define OF_SOC "soc8568@e0000000" #define OF_QE "qe@e0080000" @@ -348,7 +345,7 @@ extern unsigned long get_clock_freq(void); */ #define CONFIG_UEC_ETH #ifndef CONFIG_TSEC_ENET -#define CONFIG_ETHPRIME "Freescale GETH" +#define CONFIG_ETHPRIME "FSL UEC0" #endif #define CONFIG_PHY_MODE_NEED_CHANGE #define CONFIG_eTSEC_MDIO_BUS @@ -399,9 +396,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_TSEC1_NAME "eTSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "eTSEC1" -#undef CONFIG_TSEC3 -#undef CONFIG_TSEC4 -#undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 3 @@ -409,7 +403,10 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -/* Options are: eTSEC[0-3] */ +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ #define CONFIG_ETHPRIME "eTSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 64dcbd0..7d8a380 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -185,6 +185,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ +#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xf8100000 /* PIXIS registers */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ @@ -268,9 +269,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8641@0" #define OF_SOC "soc8641@f8000000" #define OF_TBCLK (bd->bi_busfreq / 4) @@ -417,6 +415,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define TSEC2_PHYIDX 0 #define TSEC3_PHYIDX 0 #define TSEC4_PHYIDX 0 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define CONFIG_ETHPRIME "eTSEC1" @@ -604,6 +606,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD #endif +#define CONFIG_HAS_ETH0 1 #define CONFIG_HAS_ETH1 1 #define CONFIG_HAS_ETH2 1 #define CONFIG_HAS_ETH3 1 diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index 5470373..4acbcd5 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -96,7 +96,6 @@ #define CONFIG_SUPPORT_VFAT #define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */ -#define CONFIG_AUTO_UPDATE_SHOW 1 /* use board show routine */ #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -168,36 +167,15 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ -#define CFG_NAND_LEGACY +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ @@ -276,11 +254,6 @@ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#if 0 /* test-only */ -#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ -#endif - /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) @@ -306,9 +279,6 @@ #define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/ /* total size of a CAT24WC16 is 2048 bytes */ -#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CFG_NVRAM_SIZE 242 /* NVRAM size */ - /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ @@ -317,7 +287,7 @@ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ -#if 1 /* test-only */ + /* CAT24WC08/16... */ #define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ @@ -325,15 +295,6 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ /* 16 byte page write mode using*/ /* last 4 bits of the address */ -#else -/* CAT24WC32/64... */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ - /* 32 byte page write mode using*/ - /* last 5 bits of the address */ -#endif #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE diff --git a/include/configs/PM854.h b/include/configs/PM854.h index dbf9422..a6a1e73 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -270,15 +270,19 @@ #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #define CONFIG_MPC85XX_FEC 1 #define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 +#define FEC_FLAGS 0 /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" +#define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 1 #define CONFIG_HAS_ETH2 1 diff --git a/include/configs/PM856.h b/include/configs/PM856.h index 6bdfa5d..9a17e3d 100644 --- a/include/configs/PM856.h +++ b/include/configs/PM856.h @@ -262,11 +262,12 @@ #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" -#undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #endif /* CONFIG_TSEC_ENET */ @@ -391,6 +392,7 @@ /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:40:42:01:00:00 #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:40:42:01:00:01 diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h index 2b2ae01..dccdf0c 100644 --- a/include/configs/TASREG.h +++ b/include/configs/TASREG.h @@ -43,6 +43,10 @@ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#define CONFIG_MCFTMR + +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 3d98500..e0c9d81 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -701,11 +701,9 @@ * Open firmware flat tree support *----------------------------------------------------------------------- */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 #define OF_CPU "PowerPC,5200@0" #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 4) diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index 661712b..0147252 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -253,6 +253,8 @@ extern int tqm834x_num_flash_banks; #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" @@ -499,6 +501,7 @@ extern int tqm834x_num_flash_banks; */ #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR D2:DA:5E:44:BC:29 #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 1E:F3:40:21:92:53 diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index d5ce3ba..2f23c50 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -94,7 +94,6 @@ */ #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE -#define CONFIG_ADD_RAM_INFO 1 /* print additional info*/ #if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) /* TQM8540 & 8560 need DLL-override */ @@ -266,8 +265,12 @@ #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 +#define FEC_FLAGS 0 +#define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h index 34f0ebd..3880ec7 100644 --- a/include/configs/VOH405.h +++ b/include/configs/VOH405.h @@ -153,36 +153,15 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ -#define CFG_NAND_LEGACY - -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 + +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h index c1b3da8..656784a 100644 --- a/include/configs/WUH405.h +++ b/include/configs/WUH405.h @@ -145,38 +145,16 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ -#define CFG_NAND_LEGACY - -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) - -#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */ +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 + +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ + #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ /*----------------------------------------------------------------------- diff --git a/include/configs/cmi_mpc5xx.h b/include/configs/cmi_mpc5xx.h index cd92af2..85c2b96 100644 --- a/include/configs/cmi_mpc5xx.h +++ b/include/configs/cmi_mpc5xx.h @@ -59,6 +59,8 @@ */ #include <config_cmd_default.h> +#undef CONFIG_CMD_NET /* disabeled - causes compile errors */ + #define CONFIG_CMD_MEMORY #define CONFIG_CMD_LOADB #define CONFIG_CMD_REGINFO diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index 510524a..104d94e 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -65,8 +65,10 @@ * Enable use of Ethernet * --- */ +#define CONFIG_MCFFEC -#define FEC_ENET +/* Enable Dma Timer */ +#define CONFIG_MCFTMR /* --- * Define baudrate for UART1 (console output, tftp, ...) @@ -76,6 +78,8 @@ * --- */ +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } @@ -151,6 +155,26 @@ #undef CONFIG_CMD_LOADB #undef CONFIG_CMD_MII +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif /* *----------------------------------------------------------------------------- diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h index d0bf251..9085881 100644 --- a/include/configs/hcu5.h +++ b/include/configs/hcu5.h @@ -43,7 +43,6 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the @@ -74,7 +73,6 @@ * Initial RAM & stack pointer *----------------------------------------------------------------------*/ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */ #define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ #define CFG_INIT_RAM_END (4 << 10) diff --git a/include/configs/idmr.h b/include/configs/idmr.h index 1ab7b27..404e88a 100644 --- a/include/configs/idmr.h +++ b/include/configs/idmr.h @@ -44,6 +44,8 @@ */ #define CONFIG_BOOTCOMMAND "run net_nfs" #define CONFIG_BOOTDELAY 5 +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } #define CONFIG_ETHADDR 00:06:3b:01:41:55 @@ -58,6 +60,8 @@ #define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root " \ "filesystem over NFS; echo" +#define CONFIG_MCFTMR + #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -147,11 +151,27 @@ /* * Ethernet */ -#define FEC_ENET -#define CONFIG_NET_RETRY_COUNT 5 -#define CFG_ENET_BD_BASE 0x480000 -#define CFG_DISCOVER_PHY 1 +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif /* * Definitions for initial stack pointer and data area (in DPRAM) @@ -186,7 +206,7 @@ * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) /* FLASH organization */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ @@ -216,7 +236,7 @@ "-(user)"; #if defined(CONFIG_CMD_MII) -#error MII commands don't work on iDMR board and sholud not be enabled. +#error "MII commands don't work on iDMR board and should not be enabled." #endif #endif /* _IDMR_H */ diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h index b68c5aa..b7100e9 100644 --- a/include/configs/jupiter.h +++ b/include/configs/jupiter.h @@ -145,12 +145,9 @@ #if 0 /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,5200@0" #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 8) diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 110ad44..7908e5a 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -42,7 +42,6 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ #undef CONFIG_SHOW_BOOT_PROGRESS /*----------------------------------------------------------------------- @@ -67,11 +66,11 @@ #define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ #define CFG_PCIE0_CFGBASE 0xc0000000 -#define CFG_PCIE0_XCFGBASE 0xc0000400 -#define CFG_PCIE1_CFGBASE 0xc0001000 -#define CFG_PCIE1_XCFGBASE 0xc0001400 -#define CFG_PCIE2_CFGBASE 0xc0002000 -#define CFG_PCIE2_XCFGBASE 0xc0002400 +#define CFG_PCIE1_CFGBASE 0xc1000000 +#define CFG_PCIE2_CFGBASE 0xc2000000 +#define CFG_PCIE0_XCFGBASE 0xc3000000 +#define CFG_PCIE1_XCFGBASE 0xc3001000 +#define CFG_PCIE2_XCFGBASE 0xc3002000 /* System RAM mapped to PCI space */ #define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE @@ -202,6 +201,7 @@ "setenv filesize;saveenv\0" \ "upd=run load;run update\0" \ "kozio=bootm ffc60000\0" \ + "pciconfighost=1\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -323,7 +323,7 @@ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#undef CONFIG_PCI_CONFIG_HOST_BRIDGE +#define CONFIG_PCI_CONFIG_HOST_BRIDGE /* Board-specific PCI */ #define CFG_PCI_TARGET_INIT /* let board init pci target */ diff --git a/include/configs/luan.h b/include/configs/luan.h index 26dbec9..a09dd74 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -39,7 +39,6 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 604b7d1..be48324 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -34,8 +34,8 @@ #define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the @@ -72,7 +72,6 @@ * Initial RAM & stack pointer *----------------------------------------------------------------------*/ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */ #define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ #define CFG_OCM_DATA_ADDR CFG_OCM_BASE @@ -143,15 +142,16 @@ #endif /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_ECC_ON | \ +#define CONFIG_POST (CFG_POST_CACHE | \ CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_I2C | \ - CFG_POST_CACHE | \ - CFG_POST_FPU | \ + CFG_POST_ECC_ON | \ CFG_POST_ETHER | \ - CFG_POST_SPR) + CFG_POST_FPU | \ + CFG_POST_I2C | \ + CFG_POST_MEMORY | \ + CFG_POST_RTC | \ + CFG_POST_SPR | \ + CFG_POST_UART) #define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ #define CONFIG_LOGBUFFER @@ -162,22 +162,29 @@ *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ + /* 64 byte page write mode using*/ + /* last 6 bits of the address */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */ #define CFG_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CFG_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ + +#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ +#if 0 +#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ +#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n" +#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ +#endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" +#define CONFIG_PREBOOT "setenv bootdelay 15" #undef CONFIG_BOOTARGS @@ -226,6 +233,7 @@ #define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 300 #define CONFIG_HAS_ETH0 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ @@ -391,9 +399,11 @@ #define CFG_GPIO_PHY1_RST 12 #define CFG_GPIO_FLASH_WP 14 #define CFG_GPIO_PHY0_RST 22 -#define CFG_GPIO_WATCHDOG 58 +#define CFG_GPIO_EEPROM_EXT_WP 55 +#define CFG_GPIO_EEPROM_INT_WP 57 #define CFG_GPIO_LIME_S 59 #define CFG_GPIO_LIME_RST 60 +#define CFG_GPIO_WATCHDOG 63 /*----------------------------------------------------------------------- * PPC440 GPIO Configuration diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index e0a827f..9a21632 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -417,11 +417,9 @@ extern void __led_set(led_id_t id, int state); #define CFG_RESET_ADDRESS 0xfff00100 /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 #define OF_CPU "PowerPC,5200@0" #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 4) diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h index f4f33f3..bd3107a 100644 --- a/include/configs/mpc7448hpc2.h +++ b/include/configs/mpc7448hpc2.h @@ -80,9 +80,6 @@ #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,7448@0" #define OF_TSI "tsi108@c0000000" #define OF_TBCLK (bd->bi_busfreq / 8) diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h index 8ae38cb..bec442d 100644 --- a/include/configs/p3mx.h +++ b/include/configs/p3mx.h @@ -60,7 +60,6 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 8e51d2d..7653ba1 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -266,7 +266,10 @@ #define CONFIG_CMD_DIAG #define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT #define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_NET @@ -274,12 +277,10 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO +#define CONFIG_CMD_REISER #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT #define CONFIG_CMD_USB - #define CONFIG_SUPPORT_VFAT /* @@ -488,10 +489,4 @@ /* Offset for alternate registers */ #define CFG_ATA_ALT_OFFSET (0x0000) -/* These addresses need to be shifted one place to the left - * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0) - * These values are shifted - */ -#define CFG_ATA_PORT_ADDR(port) ((port) << 1) - #endif /* __CONFIG_H */ diff --git a/include/configs/r5200.h b/include/configs/r5200.h index 0e743bb..fc7658b 100644 --- a/include/configs/r5200.h +++ b/include/configs/r5200.h @@ -39,13 +39,10 @@ #define CONFIG_M5271 /* define processor type */ #define CONFIG_R5200 /* define board type */ -#define FEC_ENET -#define CONFIG_NET_RETRY_COUNT 5 - -#define CONFIG_IPADDR 192.168.0.172 -#define CONFIG_SERVERIP 192.168.0.148 -#define CONFIG_ETHADDR 00:06:3b:00:44:55 +#define CONFIG_MCFTMR +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } @@ -87,6 +84,27 @@ #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_LOADB +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif /* Note: We only copy one sectors worth of application code from location * 10200000 for speed purposes. Increase the size if necessary */ diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 1831bef..e7d8a5a 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -313,9 +313,6 @@ #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8349@0" #define OF_SOC "soc8349@e0000000" #define OF_TBCLK (bd->bi_busfreq / 4) @@ -410,6 +407,8 @@ #define TSEC2_PHY_ADDR 0x1a #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT /* Options are: TSEC[0-1] */ #define CONFIG_ETHPRIME "TSEC0" @@ -660,6 +659,7 @@ #define CONFIG_ENV_OVERWRITE #if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:a0:1e:a0:13:8d #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:a0:1e:a0:13:8e diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 68d31ca..54eac38 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -270,9 +270,6 @@ #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8641@0" #define OF_SOC "soc@f8000000" #define OF_TBCLK (bd->bi_busfreq / 4) @@ -380,6 +377,10 @@ #define TSEC2_PHYIDX 0 #define TSEC3_PHYIDX 0 #define TSEC4_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC3_FLAGS TSEC_GIGABIT +#define TSEC4_FLAGS TSEC_GIGABIT #define CFG_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */ @@ -492,7 +493,7 @@ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -513,7 +514,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif @@ -525,7 +526,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif @@ -542,6 +543,7 @@ #define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD #endif +#define CONFIG_HAS_ETH0 1 #define CONFIG_HAS_ETH1 1 #define CONFIG_HAS_ETH2 1 #define CONFIG_HAS_ETH3 1 diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 3f75a44..c2e1386 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -343,6 +343,11 @@ #define CONFIG_CMD_USB #endif +#ifndef CONFIG_RAINIER +#define CFG_POST_FPU_ON CFG_POST_FPU +#else +#define CFG_POST_FPU_ON 0 +#endif /* POST support */ #define CONFIG_POST (CFG_POST_MEMORY | \ @@ -350,7 +355,7 @@ CFG_POST_UART | \ CFG_POST_I2C | \ CFG_POST_CACHE | \ - CFG_POST_FPU | \ + CFG_POST_FPU_ON | \ CFG_POST_ETHER | \ CFG_POST_SPR) @@ -395,7 +400,8 @@ *----------------------------------------------------------------------*/ /* General PCI */ #define CONFIG_PCI /* include pci support */ -#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h index b4ab9ad..2efc8f1 100644 --- a/include/configs/spc1920.h +++ b/include/configs/spc1920.h @@ -31,14 +31,9 @@ #undef CONFIG_8xx_CONS_NONE #define CONFIG_MII -/* #define MII_DEBUG */ -/* #define CONFIG_FEC_ENET */ #undef CONFIG_ETHER_ON_FEC1 #define CONFIG_ETHER_ON_FEC2 #define FEC_ENET -/* #define CONFIG_FEC2_PHY_NORXERR */ -/* #define CFG_DISCOVER_PHY */ -/* #define CONFIG_PHY_ADDR 0x1 */ #define CONFIG_FEC2_PHY 1 #define CONFIG_BAUDRATE 19200 @@ -100,14 +95,12 @@ #define CONFIG_CMD_ECHO #define CONFIG_CMD_IMMAP #define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_NET #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_I2C #define CONFIG_CMD_MII -#undef CONFIG_CMD_NET - - /* * Miscellaneous configurable options */ diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index 1f41cf7..c5ae0cd 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -234,12 +234,13 @@ #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" -#undef CONFIG_MPS85XX_FEC #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 4 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ @@ -378,6 +379,7 @@ /*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:e0:0c:07:9b:8a #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 55e2c8d..f32ff67 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -260,12 +260,13 @@ #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_MPS85XX_FEC #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 4 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT #define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ @@ -406,6 +407,7 @@ /*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:e0:0c:07:9b:8a #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b diff --git a/include/configs/stxxtc.h b/include/configs/stxxtc.h index 0dbf4b7..b035857 100644 --- a/include/configs/stxxtc.h +++ b/include/configs/stxxtc.h @@ -592,9 +592,6 @@ typedef unsigned int led_id_t; /* pass open firmware flat tree */ #define CONFIG_OF_FLAT_TREE 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,MPC870@0" #define OF_TBCLK (MPC8XX_HZ / 16) #define CONFIG_OF_HAS_BD_T 1 diff --git a/include/configs/trizepsiv.h b/include/configs/trizepsiv.h new file mode 100644 index 0000000..84998d4 --- /dev/null +++ b/include/configs/trizepsiv.h @@ -0,0 +1,325 @@ +/* + * (C) Copyright 2007 + * Stefano Babic, DENX Gmbh, sbabic@denx.de + * + * (C) Copyright 2004 + * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net + * + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * Configuation settings for the LUBBOCK board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_PXA27X 1 /* This is an PXA27x CPU */ + +#define LITTLEENDIAN 1 /* used by usb_ohci.c */ + +#define CONFIG_MMC 1 +#define BOARD_LATE_INIT 1 + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define RTC + +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * Hardware drivers + */ + +/* + * select serial console configuration + */ +#define CONFIG_SERIAL_MULTI +#define CONFIG_FFUART 1 /* we use FFUART on Conxs */ +#define CONFIG_BTUART 1 /* we use BTUART on Conxs */ +#define CONFIG_STUART 1 /* we use STUART on Conxs */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_BAUDRATE 38400 + +#define CONFIG_DOS_PARTITION 1 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_MMC +#define CONFIG_CMD_FAT +#define CONFIG_CMD_IMLS +#define CONFIG_CMD_PING +#define CONFIG_CMD_USB + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ + +#undef CONFIG_SHOW_BOOT_PROGRESS + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_SERVERIP 192.168.1.99 +#define CONFIG_BOOTCOMMAND "run boot_flash" +#define CONFIG_BOOTARGS "console=ttyS0,38400 ramdisk_size=12288"\ + " rw root=/dev/ram initrd=0xa0800000,5m" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "program_boot_mmc=" \ + "mw.b 0xa0010000 0xff 0x20000; " \ + "if mmcinit && " \ + "fatload mmc 0 0xa0010000 u-boot.bin; " \ + "then " \ + "protect off 0x0 0x1ffff; " \ + "erase 0x0 0x1ffff; " \ + "cp.b 0xa0010000 0x0 0x20000; " \ + "fi\0" \ + "program_uzImage_mmc=" \ + "mw.b 0xa0010000 0xff 0x180000; " \ + "if mmcinit && " \ + "fatload mmc 0 0xa0010000 uzImage; " \ + "then " \ + "protect off 0x40000 0x1bffff; " \ + "erase 0x40000 0x1bffff; " \ + "cp.b 0xa0010000 0x40000 0x180000; " \ + "fi\0" \ + "program_ramdisk_mmc=" \ + "mw.b 0xa0010000 0xff 0x500000; " \ + "if mmcinit && " \ + "fatload mmc 0 0xa0010000 ramdisk.gz; " \ + "then " \ + "protect off 0x1c0000 0x6bffff; " \ + "erase 0x1c0000 0x6bffff; " \ + "cp.b 0xa0010000 0x1c0000 0x500000; " \ + "fi\0" \ + "boot_mmc=" \ + "if mmcinit && " \ + "fatload mmc 0 0xa0030000 uzImage && " \ + "fatload mmc 0 0xa0800000 ramdisk.gz; " \ + "then " \ + "bootm 0xa0030000; " \ + "fi\0" \ + "boot_flash=" \ + "cp.b 0x1c0000 0xa0800000 0x500000; " \ + "bootm 0x40000\0" \ + +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +/* #define CONFIG_INITRD_TAG 1 */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#define CFG_LONGHELP /* undef to save memory */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT "$ " /* Monitor Command Prompt */ +#else +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#endif +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_DEVICE_NULLDEV 1 + +#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0xa1000000 /* default load address */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x207 /* need to look more closely, I think this is Turbo = 2x, L=91Mhz */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_MMC_BASE 0xF0000000 + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ +#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */ +#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */ +#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ + +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ + +#define CFG_DRAM_BASE 0xa0000000 +#define CFG_DRAM_SIZE 0x04000000 + +#define CFG_FLASH_BASE PHYS_FLASH_1 + +/* + * GPIO settings + */ +#define CFG_GPSR0_VAL 0x00018000 +#define CFG_GPSR1_VAL 0x00000000 +#define CFG_GPSR2_VAL 0x400dc000 +#define CFG_GPSR3_VAL 0x00000000 +#define CFG_GPCR0_VAL 0x00000000 +#define CFG_GPCR1_VAL 0x00000000 +#define CFG_GPCR2_VAL 0x00000000 +#define CFG_GPCR3_VAL 0x00000000 +#define CFG_GPDR0_VAL 0x00018000 +#define CFG_GPDR1_VAL 0x00028801 +#define CFG_GPDR2_VAL 0x520dc000 +#define CFG_GPDR3_VAL 0x0001E000 +#define CFG_GAFR0_L_VAL 0x801c0000 +#define CFG_GAFR0_U_VAL 0x00000013 +#define CFG_GAFR1_L_VAL 0x6990100A +#define CFG_GAFR1_U_VAL 0x00000008 +#define CFG_GAFR2_L_VAL 0xA0000000 +#define CFG_GAFR2_U_VAL 0x010900F2 +#define CFG_GAFR3_L_VAL 0x54000003 +#define CFG_GAFR3_U_VAL 0x00002401 +#define CFG_GRER0_VAL 0x00000000 +#define CFG_GRER1_VAL 0x00000000 +#define CFG_GRER2_VAL 0x00000000 +#define CFG_GRER3_VAL 0x00000000 +#define CFG_GFER0_VAL 0x00000000 +#define CFG_GFER1_VAL 0x00000000 +#define CFG_GFER2_VAL 0x00000000 +#define CFG_GFER3_VAL 0x00000020 + + +#define CFG_PSSR_VAL 0x20 /* CHECK */ + +/* + * Clock settings + */ +#define CFG_CKEN 0x01FFFFFF /* CHECK */ +#define CFG_CCCR 0x02000290 /* 520Mhz */ + +/* + * Memory settings + */ + +#define CFG_MSC0_VAL 0x4df84df0 +#define CFG_MSC1_VAL 0x7ff87ff4 +#define CFG_MSC2_VAL 0xa26936d4 +#define CFG_MDCNFG_VAL 0x880009C9 +#define CFG_MDREFR_VAL 0x20ca201e +#define CFG_MDMRS_VAL 0x00220022 + +#define CFG_FLYCNFG_VAL 0x00000000 +#define CFG_SXCNFG_VAL 0x40044004 + +/* + * PCMCIA and CF Interfaces + */ +#define CFG_MECR_VAL 0x00000001 +#define CFG_MCMEM0_VAL 0x00004204 +#define CFG_MCMEM1_VAL 0x00010204 +#define CFG_MCATT0_VAL 0x00010504 +#define CFG_MCATT1_VAL 0x00010504 +#define CFG_MCIO0_VAL 0x00008407 +#define CFG_MCIO1_VAL 0x0000c108 + +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DM9000_BASE 0x08000000 +#define DM9000_IO CONFIG_DM9000_BASE +#define DM9000_DATA (CONFIG_DM9000_BASE+0x8004) +/* #define CONFIG_DM9000_USE_8BIT */ +/* #define CONFIG_DM9000_USE_16BIT */ +#define CONFIG_DM9000_USE_32BIT + +#define CONFIG_USB_OHCI_NEW 1 +#define CFG_USB_OHCI_BOARD_INIT 1 +#define CFG_USB_OHCI_MAX_ROOT_PORTS 3 +#define CFG_USB_OHCI_REGS_BASE 0x4C000000 +#define CFG_USB_OHCI_SLOT_NAME "trizepsiv" +#define CONFIG_USB_STORAGE 1 +#define CFG_USB_OHCI_CPU_INIT 1 + +/* + * FLASH and environment organization + */ + +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER 1 + +#define CFG_MONITOR_BASE 0 +#define CFG_MONITOR_LEN 0x40000 + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 4 + 255 /* max number of sectors on one chip */ + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */ + +/* write flash less slowly */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 + +/* Flash environment locations */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (PHYS_FLASH_1 + CFG_MONITOR_LEN) /* Addr of Environment Sector */ +#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment */ +#define CFG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR+CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +#endif /* __CONFIG_H */ diff --git a/include/configs/uc101.h b/include/configs/uc101.h index 3b471d0..aed80ec 100644 --- a/include/configs/uc101.h +++ b/include/configs/uc101.h @@ -332,7 +332,6 @@ #define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ #define CONFIG_IDE_PREINIT 1 -/* #define CONFIG_IDE_RESET 1 beispile siehe tqm5200.c */ #define CFG_ATA_IDE0_OFFSET 0x0000 diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 9c536fd..74033b4 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -46,7 +46,6 @@ #define EXTCLK_83 83333333 #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ #undef CONFIG_SHOW_BOOT_PROGRESS #undef CONFIG_STRESS @@ -69,11 +68,11 @@ #define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ #define CFG_PCIE0_CFGBASE 0xc0000000 -#define CFG_PCIE0_XCFGBASE 0xc0000400 -#define CFG_PCIE1_CFGBASE 0xc0001000 -#define CFG_PCIE1_XCFGBASE 0xc0001400 -#define CFG_PCIE2_CFGBASE 0xc0002000 -#define CFG_PCIE2_XCFGBASE 0xc0002400 +#define CFG_PCIE1_CFGBASE 0xc1000000 +#define CFG_PCIE2_CFGBASE 0xc2000000 +#define CFG_PCIE0_XCFGBASE 0xc3000000 +#define CFG_PCIE1_XCFGBASE 0xc3001000 +#define CFG_PCIE2_XCFGBASE 0xc3002000 /* System RAM mapped to PCI space */ #define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE @@ -183,6 +182,7 @@ "cp.b ${fileaddr} FFFB0000 ${filesize};" \ "setenv filesize;saveenv\0" \ "upd=run load;run update\0" \ + "pciconfighost=1\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -298,7 +298,7 @@ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#undef CONFIG_PCI_CONFIG_HOST_BRIDGE +#define CONFIG_PCI_CONFIG_HOST_BRIDGE /* Board-specific PCI */ #define CFG_PCI_TARGET_INIT /* let board init pci target */ |