diff options
Diffstat (limited to 'include/configs')
28 files changed, 753 insertions, 186 deletions
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 890a6c9..2a3c058 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -687,6 +687,7 @@ */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 78bb74b..577c276 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -398,7 +398,8 @@ * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index ae4fba8..8797b30 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -416,7 +416,8 @@ extern unsigned long get_clock_freq(void); * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 96fd024..d1ac32f 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -431,7 +431,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 23594a7..33f49f5 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -471,7 +471,8 @@ extern unsigned long get_clock_freq(void); * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 5011e5a..0f71f11 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -414,7 +414,8 @@ extern unsigned long get_clock_freq(void); * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 98677e5..31740fd 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -438,7 +438,8 @@ * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index bc6c5c7..ea7a134 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -431,7 +431,8 @@ extern unsigned long get_clock_freq(void); * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 92c2b49..f69b650 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -560,8 +560,9 @@ extern unsigned long get_clock_freq(void); /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 51e5d06..081661e 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -581,7 +581,8 @@ * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 0d1f779..974cb6b 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -122,6 +122,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW #endif +#define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ + /* * DDR Setup */ diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index f9d12f5..dcaca2b 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -366,6 +366,7 @@ */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #ifdef CONFIG_CMD_KGDB diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index fca3cdd..7e901e1 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -518,6 +518,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index bf2acbf..79ce2c0 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -92,7 +92,11 @@ /* DDR Setup */ #define CONFIG_VERY_BIG_RAM +#ifdef CONFIG_MK_DDR2 +#define CONFIG_FSL_DDR2 +#else #define CONFIG_FSL_DDR3 1 +#endif #undef CONFIG_FSL_DDR_INTERACTIVE /* ECC will be enabled based on perf_mode environment variable */ @@ -109,6 +113,7 @@ #define CONFIG_CHIP_SELECTS_PER_CTRL 2 /* I2C addresses of SPD EEPROMs */ +#define CONFIG_DDR_SPD #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD EEPROM located on I2C bus 0 */ #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ @@ -228,6 +233,7 @@ #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_HWCONFIG /* enable hwconfig */ #define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */ #ifdef CONFIG_FSL_NGPIXIS @@ -249,6 +255,18 @@ #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#else +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +#endif #define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ @@ -567,7 +585,8 @@ * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) diff --git a/include/configs/P4080DS.h b/include/configs/P4080DS.h new file mode 100644 index 0000000..87703c9 --- /dev/null +++ b/include/configs/P4080DS.h @@ -0,0 +1,39 @@ +/* + * Copyright 2009-2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * P4080 DS board configuration file + */ +#define CONFIG_P4080DS +#define CONFIG_PHYS_64BIT +#define CONFIG_PPC_P4080 +#define CONFIG_SYS_NUM_FMAN 2 +#define CONFIG_SYS_NUM_FM1_DTSEC 4 +#define CONFIG_SYS_NUM_FM2_DTSEC 4 +#define CONFIG_SYS_NUM_FM1_10GEC 1 +#define CONFIG_SYS_NUM_FM2_10GEC 1 +#define CONFIG_NUM_DDR_CONTROLLERS 2 + +#define CONFIG_SYS_P4080_ERRATUM_CPU22 +#define CONFIG_SYS_P4080_ERRATUM_SERDES8 + +#include "corenet_ds.h" diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index d8f2602..abbaf38 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -280,6 +280,7 @@ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " diff --git a/include/configs/XPEDITE5200.h b/include/configs/XPEDITE5200.h index 83aeffd..1fbe4fb 100644 --- a/include/configs/XPEDITE5200.h +++ b/include/configs/XPEDITE5200.h @@ -351,6 +351,7 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ #define CONFIG_PANIC_HANG /* do not reset board on panic */ diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h index fc4a986..8225fff 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/XPEDITE5370.h @@ -409,6 +409,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ #define CONFIG_PANIC_HANG /* do not reset board on panic */ diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h index 37a7059..95d3afa 100644 --- a/include/configs/bf533-ezkit.h +++ b/include/configs/bf533-ezkit.h @@ -94,49 +94,10 @@ /* * I2C Settings - * By default PF1 is used as SDA and PF0 as SCL on the Stamp board */ #define CONFIG_SOFT_I2C -#ifdef CONFIG_SOFT_I2C -#define PF_SCL PF0 -#define PF_SDA PF1 -#define I2C_INIT \ - do { \ - *pFIO_DIR |= PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_ACTIVE \ - do { \ - *pFIO_DIR |= PF_SDA; \ - *pFIO_INEN &= ~PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_TRISTATE \ - do { \ - *pFIO_DIR &= ~PF_SDA; \ - *pFIO_INEN |= PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) -#define I2C_SDA(bit) \ - do { \ - if (bit) \ - *pFIO_FLAG_S = PF_SDA; \ - else \ - *pFIO_FLAG_C = PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_SCL(bit) \ - do { \ - if (bit) \ - *pFIO_FLAG_S = PF_SCL; \ - else \ - *pFIO_FLAG_C = PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#endif +#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0 +#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1 /* diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index 02c8bc3..f39bfee 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -138,49 +138,10 @@ /* * I2C Settings - * By default PF2 is used as SDA and PF3 as SCL on the Stamp board */ #define CONFIG_SOFT_I2C -#ifdef CONFIG_SOFT_I2C -#define PF_SCL PF3 -#define PF_SDA PF2 -#define I2C_INIT \ - do { \ - *pFIO_DIR |= PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_ACTIVE \ - do { \ - *pFIO_DIR |= PF_SDA; \ - *pFIO_INEN &= ~PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_TRISTATE \ - do { \ - *pFIO_DIR &= ~PF_SDA; \ - *pFIO_INEN |= PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) -#define I2C_SDA(bit) \ - do { \ - if (bit) \ - *pFIO_FLAG_S = PF_SDA; \ - else \ - *pFIO_FLAG_C = PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_SCL(bit) \ - do { \ - if (bit) \ - *pFIO_FLAG_S = PF_SCL; \ - else \ - *pFIO_FLAG_C = PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#endif +#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3 +#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2 /* diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h index 036bfe4..4e293b5 100644 --- a/include/configs/bf561-ezkit.h +++ b/include/configs/bf561-ezkit.h @@ -112,46 +112,8 @@ * I2C Settings */ #define CONFIG_SOFT_I2C -#ifdef CONFIG_SOFT_I2C -#define PF_SCL PF0 -#define PF_SDA PF1 -#define I2C_INIT \ - do { \ - *pFIO0_DIR |= PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_ACTIVE \ - do { \ - *pFIO0_DIR |= PF_SDA; \ - *pFIO0_INEN &= ~PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_TRISTATE \ - do { \ - *pFIO0_DIR &= ~PF_SDA; \ - *pFIO0_INEN |= PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0) -#define I2C_SDA(bit) \ - do { \ - if (bit) \ - *pFIO0_FLAG_S = PF_SDA; \ - else \ - *pFIO0_FLAG_C = PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_SCL(bit) \ - do { \ - if (bit) \ - *pFIO0_FLAG_S = PF_SCL; \ - else \ - *pFIO0_FLAG_C = PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#endif +#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0 +#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1 /* diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index 901a32f..4476268 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -68,6 +68,7 @@ # endif # if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) # define CONFIG_CMD_I2C +# define CONFIG_SOFT_I2C_READ_REPEATED_START # endif # ifdef CONFIG_SYS_NO_FLASH # undef CONFIG_CMD_FLASH diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h index aa33933..85f08ea 100644 --- a/include/configs/blackstamp.h +++ b/include/configs/blackstamp.h @@ -206,32 +206,8 @@ * them yet. You can (and probably should) change these values! */ #ifdef CONFIG_SOFT_I2C - -#define PF_SCL PF9 -#define PF_SDA PF8 - -#define I2C_INIT do { *pFIO_DIR |= PF_SCL; SSYNC(); } while (0) -#define I2C_ACTIVE do { *pFIO_DIR |= PF_SDA; *pFIO_INEN &= ~PF_SDA; SSYNC(); } while (0) -#define I2C_TRISTATE do { *pFIO_DIR &= ~PF_SDA; *pFIO_INEN |= PF_SDA; SSYNC(); } while (0) -#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) -#define I2C_SDA(bit) \ - do { \ - if (bit) \ - *pFIO_FLAG_S = PF_SDA; \ - else \ - *pFIO_FLAG_C = PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_SCL(bit) \ - do { \ - if (bit) \ - *pFIO_FLAG_S = PF_SCL; \ - else \ - *pFIO_FLAG_C = PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - +#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9 +#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8 #define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_SYS_I2C_SLAVE 0xFE #endif diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h new file mode 100644 index 0000000..dd609da --- /dev/null +++ b/include/configs/corenet_ds.h @@ -0,0 +1,653 @@ +/* + * Copyright 2009-2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Corenet DS style board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#include "../board/freescale/common/ics307_clk.h" + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ +#define CONFIG_SYS_HAS_SERDES /* has SERDES */ + +#define CONFIG_SRIO1 /* SRIO port 1 */ +#define CONFIG_SRIO2 /* SRIO port 2 */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +//#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ +#endif + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xfe000000 /* relocated CCSRBAR */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_PHYS 0xffe000000ull /* physical addr of CCSRBAR */ +#else +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#endif +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull +#endif + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_FSL_DDR3 + +#ifdef CONFIG_DDR_SPD +#define CONFIG_SYS_SPD_BUS_NUM 1 +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#else +#define CONFIG_SYS_SDRAM_SIZE 4096 + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f +#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_TIMING_3 0x01031000 +#define CONFIG_SYS_DDR_TIMING_0 0x55440804 +#define CONFIG_SYS_DDR_TIMING_1 0x74713a66 +#define CONFIG_SYS_DDR_TIMING_2 0x0fb8911b +#define CONFIG_SYS_DDR_MODE_1 0x00421850 +#define CONFIG_SYS_DDR_MODE_2 0x00100000 +#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000 +#define CONFIG_SYS_DDR_INTERVAL 0x10400100 +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x03401500 +#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8655a608 +#define CONFIG_SYS_DDR_CONTROL 0xc7048000 +#define CONFIG_SYS_DDR_CONTROL2 0x24400011 +#define CONFIG_SYS_DDR_CDR1 0x00000000 +#define CONFIG_SYS_DDR_CDR2 0x00000000 +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x00010000 +#define CONFIG_SYS_DDR_DEBUG_18 0x40100400 + +#define CONFIG_SYS_DDR2_CS0_BNDS 0x008000bf +#define CONFIG_SYS_DDR2_CS1_BNDS 0x00C000ff +#define CONFIG_SYS_DDR2_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG +#define CONFIG_SYS_DDR2_CS1_CONFIG CONFIG_SYS_DDR_CS1_CONFIG +#define CONFIG_SYS_DDR2_TIMING_3 CONFIG_SYS_DDR_TIMING_3 +#define CONFIG_SYS_DDR2_TIMING_0 CONFIG_SYS_DDR_TIMING_0 +#define CONFIG_SYS_DDR2_TIMING_1 CONFIG_SYS_DDR_TIMING_1 +#define CONFIG_SYS_DDR2_TIMING_2 CONFIG_SYS_DDR_TIMING_2 +#define CONFIG_SYS_DDR2_MODE_1 CONFIG_SYS_DDR_MODE_1 +#define CONFIG_SYS_DDR2_MODE_2 CONFIG_SYS_DDR_MODE_2 +#define CONFIG_SYS_DDR2_MODE_CTRL CONFIG_SYS_DDR_MODE_CTRL +#define CONFIG_SYS_DDR2_INTERVAL CONFIG_SYS_DDR_INTERVAL +#define CONFIG_SYS_DDR2_DATA_INIT CONFIG_SYS_DDR_DATA_INIT +#define CONFIG_SYS_DDR2_CLK_CTRL CONFIG_SYS_DDR_CLK_CTRL +#define CONFIG_SYS_DDR2_TIMING_4 CONFIG_SYS_DDR_TIMING_4 +#define CONFIG_SYS_DDR2_TIMING_5 CONFIG_SYS_DDR_TIMING_5 +#define CONFIG_SYS_DDR2_ZQ_CNTL CONFIG_SYS_DDR_ZQ_CNTL +#define CONFIG_SYS_DDR2_WRLVL_CNTL CONFIG_SYS_DDR_WRLVL_CNTL +#define CONFIG_SYS_DDR2_CONTROL CONFIG_SYS_DDR_CONTROL +#define CONFIG_SYS_DDR2_CONTROL2 CONFIG_SYS_DDR_CONTROL2 +#define CONFIG_SYS_DDR2_CDR1 CONFIG_SYS_DDR_CDR1 +#define CONFIG_SYS_DDR2_CDR2 CONFIG_SYS_DDR_CDR2 +#define CONFIG_SYS_DDR2_ERR_INT_EN CONFIG_SYS_DDR_ERR_INT_EN +#define CONFIG_SYS_DDR2_ERR_DIS CONFIG_SYS_DDR_ERR_DIS +#define CONFIG_SYS_DDR2_SBE CONFIG_SYS_DDR_SBE +#define CONFIG_SYS_DDR2_DEBUG_18 CONFIG_SYS_DDR_DEBUG_18 + +#endif + +/* + * Local Bus Definitions + */ + +/* Set the local bus clock 1/8 of platform clock */ +#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 + +#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* Start of PromJet */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull +#else +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif + +#define CONFIG_SYS_BR0_PRELIM \ + (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ + BR_PS_16 | BR_V) +#define CONFIG_SYS_OR0_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ + | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) + +#define CONFIG_SYS_BR1_PRELIM \ + (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 + +#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */ +#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ +#ifdef CONFIG_PHYS_64BIT +#define PIXIS_BASE_PHYS 0xfffdf0000ull +#else +#define PIXIS_BASE_PHYS PIXIS_BASE +#endif + +#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ + +#define PIXIS_LBMAP_SWITCH 7 +#define PIXIS_LBMAP_MASK 0xf0 +#define PIXIS_LBMAP_SHIFT 4 +#define PIXIS_LBMAP_ALTBANK 0x40 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#else +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +#endif +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x118000 +#define CONFIG_SYS_I2C2_OFFSET 0x118100 + +/* + * RapidIO + */ +#define CONFIG_SYS_RIO1_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_RIO1_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_RIO1_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_RIO1_MEM_SIZE 0x10000000 /* 256M */ + +#define CONFIG_SYS_RIO2_MEM_VIRT 0xb0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_RIO2_MEM_PHYS 0xc30000000ull +#else +#define CONFIG_SYS_RIO2_MEM_PHYS 0xb0000000 +#endif +#define CONFIG_SYS_RIO2_MEM_SIZE 0x10000000 /* 256M */ + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#else +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 +#endif +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#else +#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 +#endif +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#else +#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 +#endif +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xe0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull +#else +#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 +#endif +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#else +#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 +#endif +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* Qman/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 10 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#else +#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE +#endif +#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 10 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull +#else +#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE +#endif +#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME +/* Default address of microcode for the Linux Fman driver */ +#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FMAN_FW_ADDR_PHYS 0xFEF000000ULL +#else +#define CONFIG_SYS_FMAN_FW_ADDR_PHYS CONFIG_SYS_FMAN_FW_ADDR +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#endif + +#ifdef CONFIG_PCI + +/*PCIE video card used*/ +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT + +/* video */ +#define CONFIG_VIDEO + +#ifdef CONFIG_VIDEO +#define CONFIG_BIOSEMU +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_ATI_RADEON_FB +#define CONFIG_VIDEO_LOGO +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#endif + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#ifndef CONFIG_PCI_PNP +#define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS +#define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS +#define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ +#endif + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1c +#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x1d +#define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x1e +#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1f +#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 + +#if (CONFIG_SYS_NUM_FMAN == 2) +#define CONFIG_SYS_FM2_DTSEC1_PHY_ADDR 0x1c +#define CONFIG_SYS_FM2_DTSEC2_PHY_ADDR 0x1d +#define CONFIG_SYS_FM2_DTSEC3_PHY_ADDR 0x1e +#define CONFIG_SYS_FM2_DTSEC4_PHY_ADDR 0x1f +#define CONFIG_SYS_FM2_10GEC1_PHY_ADDR 0 +#endif + +#define CONFIG_SYS_TBIPA_VALUE 8 +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* +* USB +*/ +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH /opt/nfsroot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=p4080ds/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=p4080ds/p4080ds.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" \ + "fman_ucode="MK_STR(CONFIG_SYS_FMAN_FW_ADDR_PHYS)"\0" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT + +#endif /* __CONFIG_H */ diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h index 2c0a263..53b5197 100644 --- a/include/configs/ibf-dsp561.h +++ b/include/configs/ibf-dsp561.h @@ -112,33 +112,8 @@ * I2C Settings */ #define CONFIG_SOFT_I2C 1 -#define PF_SCL 0x1/*PF0*/ -#define PF_SDA 0x2/*PF1*/ - -#ifdef CONFIG_SOFT_I2C -#define I2C_INIT do { *pFIO0_DIR |= PF_SCL; SSYNC(); } while (0) -#define I2C_ACTIVE do { *pFIO0_DIR |= PF_SDA; *pFIO0_INEN &= ~PF_SDA; SSYNC(); } while (0) -#define I2C_TRISTATE do { *pFIO0_DIR &= ~PF_SDA; *pFIO0_INEN |= PF_SDA; SSYNC(); } while (0) -#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0) -#define I2C_SDA(bit) \ - do { \ - if (bit) \ - *pFIO0_FLAG_S = PF_SDA; \ - else \ - *pFIO0_FLAG_C = PF_SDA; \ - SSYNC(); \ - } while (0) -#define I2C_SCL(bit) \ - do { \ - if (bit) \ - *pFIO0_FLAG_S = PF_SCL; \ - else \ - *pFIO0_FLAG_C = PF_SCL; \ - SSYNC(); \ - } while (0) -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#endif +#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0 +#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1 /* diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index c8b8d0d..564f661 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -496,6 +496,7 @@ * Miscellaneous configurable options */ #define CONFIG_CMDLINE_EDITING /* undef to save memory */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ diff --git a/include/configs/socrates.h b/include/configs/socrates.h index ad70109..af1e19e 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -233,6 +233,7 @@ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 363f7b4..57bb8d1 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -189,6 +189,7 @@ #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |