summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/IceCube.h13
-rw-r--r--include/configs/MPC8349EMDS.h70
-rw-r--r--include/configs/MPC8349ITX.h804
-rw-r--r--include/configs/MPC8360EMDS.h635
-rw-r--r--include/configs/TQM834x.h28
-rw-r--r--include/configs/p3mx.h450
6 files changed, 1980 insertions, 20 deletions
diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
index 1152f83..0d38254 100644
--- a/include/configs/IceCube.h
+++ b/include/configs/IceCube.h
@@ -172,6 +172,19 @@
#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
#endif
#endif /* CONFIG_MPC5200 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
/*
* I2C configuration
*/
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 66f1646..5bed2d0 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -36,6 +36,7 @@
*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC83XX 1 /* MPC83XX family */
+#define CONFIG_MPC834X 1 /* MPC834X family */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */
@@ -59,9 +60,20 @@
#endif
#endif
+#define CFG_SCCR_INIT (SCCR_DEFAULT & (~SCCR_CLK_MASK))
+#define CFG_SCCR_TSEC1CM SCCR_TSEC1CM_1 /* TSEC1 clock setting */
+#define CFG_SCCR_TSEC2CM SCCR_TSEC2CM_1 /* TSEC2 clock setting */
+#define CFG_SCCR_ENCCM SCCR_ENCCM_3 /* ENC clock setting */
+#define CFG_SCCR_USBCM SCCR_USBCM_3 /* USB clock setting */
+#define CFG_SCCR_VAL ( CFG_SCCR_INIT \
+ | CFG_SCCR_TSEC1CM \
+ | CFG_SCCR_TSEC2CM \
+ | CFG_SCCR_ENCCM \
+ | CFG_SCCR_USBCM )
+
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
-#define CFG_IMMRBAR 0xE0000000
+#define CFG_IMMR 0xE0000000
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00000000 /* memtest region */
@@ -299,8 +311,8 @@
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
@@ -308,20 +320,35 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8349@0"
+#define OF_SOC "soc8349@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500"
+
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
#define CFG_I2C2_OFFSET 0x3100
/* TSEC */
#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMRBAR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMRBAR+CFG_TSEC2_OFFSET)
+#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
/* USB */
#define CFG_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
@@ -615,8 +642,8 @@
#endif
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CFG_IBAT5L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT5U (CFG_IMMRBAR | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
@@ -666,11 +693,11 @@
#define CONFIG_ETH1ADDR 00:E0:0C:00:7E:21
#endif
-#define CONFIG_IPADDR 192.168.205.5
+#define CONFIG_IPADDR 192.168.1.253
#define CONFIG_HOSTNAME mpc8349emds
-#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx
-#define CONFIG_BOOTFILE /tftpboot/tqm83xx/uImage
+#define CONFIG_ROOTPATH /nfsroot/rootfs
+#define CONFIG_BOOTFILE uImage
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
@@ -703,14 +730,31 @@
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=/tftpboot/mpc8349emds/uImage\0" \
"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \
"update=protect off fe000000 fe03ffff; " \
"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0" \
"upd=run load;run update\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8349emds.dtb\0" \
""
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
#define CONFIG_BOOTCOMMAND "run flash_self"
#endif /* __CONFIG_H */
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
new file mode 100644
index 0000000..cbdbb29
--- /dev/null
+++ b/include/configs/MPC8349ITX.h
@@ -0,0 +1,804 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ MPC8349E-mITX board configuration file
+
+ Memory map:
+
+ 0x0000_0000-0x0FFF_FFFF DDR SDRAM (256 MB)
+ 0x8000_0000-0x9FFF_FFFF PCI1 memory space (512 MB)
+ 0xA000_0000-0xBFFF_FFFF PCI2 memory space (512 MB)
+ 0xE000_0000-0xEFFF_FFFF IMMR (1 MB)
+ 0xE200_0000-0xE2FF_FFFF PCI1 I/O space (16 MB)
+ 0xE300_0000-0xE3FF_FFFF PCI2 I/O space (16 MB)
+ 0xF000_0000-0xF000_FFFF Compact Flash
+ 0xF001_0000-0xF001_FFFF Local bus expansion slot
+ 0xF800_0000-0xF801_FFFF GBE L2 Switch VSC7385
+ 0xFF00_0000-0xFF7F_FFFF Alternative bank of Flash memory (8MB)
+ 0xFF80_0000-0xFFFF_FFFF Boot Flash (8 MB)
+
+ I2C address list:
+ Align. Board
+ Bus Addr Part No. Description Length Location
+ ----------------------------------------------------------------
+ I2C0 0x50 M24256-BWMN6P Board EEPROM 2 U64
+
+ I2C1 0x20 PCF8574 I2C Expander 0 U8
+ I2C1 0x21 PCF8574 I2C Expander 0 U10
+ I2C1 0x38 PCF8574A I2C Expander 0 U8
+ I2C1 0x39 PCF8574A I2C Expander 0 U10
+ I2C1 0x51 (DDR) DDR EEPROM 1 U1
+ I2C1 0x68 DS1339 RTC 1 U68
+
+ Note that a given board has *either* a pair of 8574s or a pair of 8574As.
+*/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC834X /* MPC834x family (8343, 8347, 8349) */
+#define CONFIG_MPC8349 /* MPC8349 specific */
+
+#define CONFIG_PCI
+
+#define CONFIG_COMPACT_FLASH /* The CF card interface on the back of the board */
+#define CONFIG_RTC_DS1337
+
+/* I2C */
+#define CONFIG_HARD_I2C
+
+#ifdef CONFIG_HARD_I2C
+
+#define CONFIG_MISC_INIT_F
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+#define CFG_SPD_BUS_NUM 1 /* The I2C bus for SPD */
+
+#define CFG_I2C_8574_ADDR1 0x20 /* I2C1, PCF8574 */
+#define CFG_I2C_8574_ADDR2 0x21 /* I2C1, PCF8574 */
+#define CFG_I2C_8574A_ADDR1 0x38 /* I2C1, PCF8574A */
+#define CFG_I2C_8574A_ADDR2 0x39 /* I2C1, PCF8574A */
+#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C0, Board EEPROM */
+#define CFG_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/
+#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */
+
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+/* Don't probe these addresses: */
+#define CFG_I2C_NOPROBES {{1, CFG_I2C_8574_ADDR1}, \
+ {1, CFG_I2C_8574_ADDR2}, \
+ {1, CFG_I2C_8574A_ADDR1}, \
+ {1, CFG_I2C_8574A_ADDR2}}
+/* Bit definitions for the 8574[A] I2C expander */
+#define I2C_8574_REVISION 0x03 /* Board revision, 00=0.0, 01=0.1, 10=1.0 */
+#define I2C_8574_CF 0x08 /* 1=Compact flash absent, 0=present */
+#define I2C_8574_MPCICLKRN 0x10 /* MiniPCI Clk Run */
+#define I2C_8574_PCI66 0x20 /* 0=33MHz PCI, 1=66MHz PCI */
+#define I2C_8574_FLASHSIDE 0x40 /* 0=Reset vector from U4, 1=from U7*/
+
+#undef CONFIG_SOFT_I2C
+
+#endif
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define PCI_66M
+#ifdef PCI_66M
+#define CONFIG_83XX_CLKIN 66666666 /* in Hz */
+#else
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#endif
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#ifdef PCI_66M
+#define CONFIG_SYS_CLK_FREQ 66666666
+#else
+#define CONFIG_SYS_CLK_FREQ 33333333
+#endif
+#endif
+
+#define CFG_IMMR 0xE0000000 /* The IMMR is relocated to here */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00003000 /* memtest region */
+#define CFG_MEMTEST_END 0x07100000 /* only has 128M */
+
+/*
+ * DDR Setup
+ */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#undef CONFIG_DDR_2T_TIMING
+#define CFG_83XX_DDR_USES_CS0
+
+#ifndef CONFIG_SPD_EEPROM
+/*
+ * Manually set up DDR parameters
+ */
+ #define CFG_DDR_SIZE 256 /* Mb */
+ #define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+
+ #define CFG_DDR_TIMING_1 0x26242321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45, may need tuning */
+#endif
+
+/* FLASH on the Local Bus */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
+#define CFG_FLASH_SIZE 16 /* FLASH size in MB */
+#define CFG_FLASH_EMPTY_INFO
+
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V)
+#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16Mb window bytes */
+
+/* VSC7385 on the Local Bus */
+#define CFG_VSC7385_BASE 0xF8000000 /* start of VSC7385 */
+
+#define CFG_BR1_PRELIM (CFG_VSC7385_BASE | BR_PS_8 | BR_V)
+#define CFG_OR1_PRELIM (0xFFFE0000 /* 128KB */ | \
+ OR_GPCM_CSNT | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_SETA | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#define CFG_LBLAWBAR1_PRELIM CFG_VSC7385_BASE /* Access window base at VSC7385 base */
+#define CFG_LBLAWAR1_PRELIM 0x80000010 /* Access window size 128K */
+
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_SECT 135 /* sectors per device */
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE + 0x800000}
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_LED_BASE 0xF9000000 /* start of LED and Board ID */
+#define CFG_BR2_PRELIM (CFG_LED_BASE | BR_PS_8 | BR_V)
+#define CFG_OR2_PRELIM (0xFFE00000 /* 2MB */ | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | \
+ OR_GPCM_SCY_9 | \
+ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#ifdef CONFIG_COMPACT_FLASH
+
+#define CFG_CF_BASE 0xF0000000
+
+#define CFG_BR3_PRELIM (CFG_CF_BASE | BR_PS_16 | BR_MS_UPMA | BR_V)
+#define CFG_OR3_PRELIM (OR_UPM_AM | OR_UPM_BI)
+
+#define CFG_LBLAWBAR2_PRELIM CFG_CF_BASE /* Window base at flash base + LED & Board ID */
+#define CFG_LBLAWAR2_PRELIM 0x8000000F /* 64K bytes */
+
+#undef CONFIG_IDE_RESET
+#undef CONFIG_IDE_PREINIT
+
+#define CFG_IDE_MAXBUS 1
+#define CFG_IDE_MAXDEVICE 1
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR CFG_CF_BASE
+#define CFG_ATA_DATA_OFFSET 0x0000
+#define CFG_ATA_REG_OFFSET 0
+#define CFG_ATA_ALT_OFFSET 0x0200
+#define CFG_ATA_STRIDE 2
+
+#define ATA_RESET_TIME 1 /* If a CF card is not inserted, time out quickly */
+
+#endif
+
+#define CONFIG_DOS_PARTITION
+
+#define CFG_MID_FLASH_JUMP 0x7F000000
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ * LCRR: DLL bypass, Clock divider is 4
+ * External Local Bus rate is
+ * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
+ */
+#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CFG_LBC_LBCR 0x00000000
+
+#undef CFG_LB_SDRAM /* if board has SRDAM on local bus */
+
+#ifdef CFG_LB_SDRAM
+/*local bus BR2, OR2 definition for SDRAM if soldered on the ADS board*/
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
+ */
+
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+#define CFG_LBLAWBAR2_PRELIM 0xF0000000
+#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64M */
+
+#define CFG_BR2_PRELIM (CFG_LBC_SDRAM_BASE | BR_PS_32 | BR_MS_SDRAM | BR_V)
+#define CFG_OR2_PRELIM (0xFC000000 /* 64 MB */ | \
+ OR_SDRAM_XAM | \
+ ((9 - 7) << OR_SDRAM_COLS_SHIFT) | \
+ ((13 - 9) << OR_SDRAM_ROWS_SHIFT) | \
+ OR_SDRAM_EAD)
+
+#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR8 (5 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT6 (5 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC3 (3 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFEN \
+ | CFG_LBC_LSDMR_BSMA1516 \
+ | CFG_LBC_LSDMR_RFCR8 \
+ | CFG_LBC_LSDMR_PRETOACT6 \
+ | CFG_LBC_LSDMR_ACTTORW3 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC3 \
+ | CFG_LBC_LSDMR_CL3 \
+ )
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_NORMAL)
+#endif
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8349@0"
+#define OF_SOC "soc8349@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500"
+
+#ifdef CONFIG_PCI
+
+#define CONFIG_MPC83XX_PCI2
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE (CFG_PCI1_MEM_BASE + CFG_PCI1_MEM_SIZE)
+#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xE2000000
+#define CFG_PCI1_IO_SIZE 0x01000000 /* 16M */
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CFG_PCI2_MEM_BASE (CFG_PCI1_MMIO_BASE + CFG_PCI1_MMIO_SIZE)
+#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_MMIO_BASE (CFG_PCI2_MEM_BASE + CFG_PCI2_MEM_SIZE)
+#define CFG_PCI2_MMIO_PHYS CFG_PCI2_MMIO_BASE
+#define CFG_PCI2_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS (CFG_PCI1_IO_PHYS + CFG_PCI1_IO_SIZE)
+#define CFG_PCI2_IO_SIZE 0x01000000 /* 16M */
+#endif
+
+#define _IO_BASE 0x00000000 /* points to PCI I/O space */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x) (x)
+#endif
+
+#ifndef CONFIG_PCI_PNP
+ #define PCI_ENET0_IOADDR 0x00000000
+ #define PCI_ENET0_MEMADDR CFG_PCI2_MEM_BASE
+ #define PCI_IDSEL_NUMBER 0x0f /* IDSEL = AD15 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#endif
+
+/* TSEC */
+
+#ifdef CONFIG_TSEC_ENET
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+#define CONFIG_MII
+#define CONFIG_PHY_GIGE /* In case CFG_CMD_MII is specified */
+
+#define CONFIG_MPC83XX_TSEC1
+
+#ifdef CONFIG_MPC83XX_TSEC1
+#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
+#define CFG_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x1c /* VSC8201 uses address 0x1c */
+#define TSEC1_PHYIDX 0
+#endif
+
+#ifdef CONFIG_MPC83XX_TSEC2
+#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
+#define CFG_TSEC2_OFFSET 0x25000
+#define CONFIG_UNKNOWN_TSEC /* TSEC2 is proprietary */
+#define TSEC2_PHY_ADDR 4
+#define TSEC2_PHYIDX 0
+#endif
+
+#define CONFIG_ETHPRIME "Freescale TSEC"
+
+#endif
+
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_NO_FLASH /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/* CONFIG_COMMANDS */
+
+#ifdef CONFIG_COMPACT_FLASH
+#define CONFIG_COMMANDS_CF (CFG_CMD_IDE | CFG_CMD_FAT)
+#else
+#define CONFIG_COMMANDS_CF 0
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_COMMANDS_PCI CFG_CMD_PCI
+#else
+#define CONFIG_COMMANDS_PCI 0
+#endif
+
+#ifdef CONFIG_HARD_I2C
+#define CONFIG_COMMANDS_I2C CFG_CMD_I2C
+#else
+#define CONFIG_COMMANDS_I2C 0
+#endif
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CONFIG_COMMANDS_CF | \
+ CFG_CMD_NET | \
+ CFG_CMD_PING | \
+ CONFIG_COMMANDS_I2C | \
+ CONFIG_COMMANDS_PCI | \
+ CFG_CMD_SDRAM | \
+ CFG_CMD_DATE | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_IRQ)
+#include <cmd_confdefs.h>
+
+/* Watchdog */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#ifdef CONFIG_WATCHDOG
+#define CFG_WATCHDOG_VALUE 0xFFFFFFC3
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log2 of the above value */
+#endif
+
+#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#define CFG_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_VCO_1X2 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#ifdef PCI_64BIT
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_64_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII )
+#else
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_32_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0XFFF00100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII )
+#endif
+
+/* System performance */
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CFG_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
+#define CFG_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
+#define CFG_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
+#define CFG_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count */
+
+/* System IO Config */
+#define CFG_SICRH SICRH_TSOBI1 /* Needed for gigabit to work on TSEC 1 */
+#define CFG_SICRL (SICRL_LDP_A | SICRL_USB1)
+
+#define CFG_HID0_INIT 0x000000000
+
+#define CFG_HID0_FINAL CFG_HID0_INIT
+
+#define CFG_HID2 HID2_HBE
+
+/* DDR @ 0x00000000 */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#ifdef CONFIG_PCI
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT1L 0
+#define CFG_IBAT1U 0
+#define CFG_IBAT2L 0
+#define CFG_IBAT2U 0
+#endif
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CFG_IBAT3L (CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT3U (CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT4U (CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT3L 0
+#define CFG_IBAT3U 0
+#define CFG_IBAT4L 0
+#define CFG_IBAT4U 0
+#endif
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT7L 0
+#define CFG_IBAT7U 0
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_MPC83XX_TSEC1
+#define CONFIG_ETHADDR 00:E0:0C:00:8C:01
+#endif
+
+#ifdef CONFIG_MPC83XX_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:00:8C:02
+#endif
+
+#if 1
+#define CONFIG_IPADDR 10.82.19.159
+#define CONFIG_SERVERIP 10.82.48.106
+#define CONFIG_GATEWAYIP 10.82.19.254
+#define CONFIG_NETMASK 255.255.252.0
+#define CONFIG_NETDEV eth0
+
+#define CONFIG_HOSTNAME mpc8349emitx
+#define CONFIG_ROOTPATH /nfsroot0/u/timur/itx-ltib/rootfs
+#define CONFIG_BOOTFILE timur/uImage
+
+#define CONFIG_UBOOTPATH timur/u-boot.bin
+#else
+#define CONFIG_IPADDR 192.168.1.253
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.252.0
+#define CONFIG_NETDEV eth0
+
+#define CONFIG_HOSTNAME mpc8349emitx
+#define CONFIG_ROOTPATH /nfsroot/rootfs
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_UBOOTPATH u-boot.bin
+#endif
+
+#define CONFIG_UBOOTSTART fe700000
+#define CONFIG_UBOOTEND fe77ffff
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BAUDRATE 115200
+
+#undef CONFIG_BOOTCOMMAND
+#ifdef CONFIG_BOOTCOMMAND
+#define CONFIG_BOOTDELAY 6
+#else
+#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#endif
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_BOOTARGS \
+ "root=/dev/nfs rw" \
+ " nfsroot=" MK_STR(CONFIG_SERVERIP) ":" MK_STR(CONFIG_ROOTPATH) \
+ " ip=" MK_STR(CONFIG_IPADDR) ":" MK_STR(CONFIG_SERVERIP) ":" \
+ MK_STR(CONFIG_GATEWAYIP) ":" MK_STR(CONFIG_NETMASK) ":" \
+ MK_STR(CONFIG_HOSTNAME) ":" MK_STR(CONFIG_NETDEV) ":off" \
+ " console=ttyS0," MK_STR(CONFIG_BAUDRATE)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "tftpflash=tftpboot $loadaddr " MK_STR(CONFIG_UBOOTPATH) "; " \
+ "erase " MK_STR(CONFIG_UBOOTSTART) " " MK_STR(CONFIG_UBOOTEND) "; " \
+ "cp.b $loadaddr " MK_STR(CONFIG_UBOOTSTART) " $filesize; " \
+ "cmp.b $loadaddr " MK_STR(CONFIG_UBOOTSTART) " $filesize\0" \
+ "tftpupdate=tftpboot $loadaddr " MK_STR(CONFIG_UBOOTPATH) "; " \
+ "protect off FEF00000 FEF7FFFF; " \
+ "erase FEF00000 FEF7FFFF; " \
+ "cp.b $loadaddr FEF00000 $filesize; " \
+ "protect on FEF00000 FEF7FFFF; " \
+ "cmp.b $loadaddr FEF00000 $filesize\0" \
+ "tftplinux=tftpboot $loadaddr $bootfile; bootm\0" \
+ "copyuboot=erase " MK_STR(CONFIG_UBOOTSTART) " " MK_STR(CONFIG_UBOOTEND) "; " \
+ "cp.b fef00000 " MK_STR(CONFIG_UBOOTSTART) " 80000\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8349emitx.dtb\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
new file mode 100644
index 0000000..8ad6551
--- /dev/null
+++ b/include/configs/MPC8360EMDS.h
@@ -0,0 +1,635 @@
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *
+ * Dave Liu <daveliu@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_QE 1 /* Has QE */
+#define CONFIG_MPC83XX 1 /* MPC83XX family */
+#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
+#define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */
+
+/*
+ * System Clock Setup
+ */
+#ifdef CONFIG_PCISLAVE
+#define CONFIG_83XX_PCICLK 66000000 /* in HZ */
+#else
+#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
+#endif
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 66000000
+#endif
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CFG_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_VCO_1X2 |\
+ HRCWL_CE_PLL_VCO_DIV_4 |\
+ HRCWL_CE_PLL_DIV_1X1 |\
+ HRCWL_CE_TO_PLL_1X6 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#ifdef CONFIG_PCISLAVE
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_AGENT |\
+ HRCWH_PCI1_ARBITER_DISABLE |\
+ HRCWH_PCICKDRV_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0XFFF00100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT)
+#else
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCICKDRV_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT)
+#endif
+
+/*
+ * System IO Config
+ */
+#define CFG_SICRH 0x00000000
+#define CFG_SICRL 0x40000000
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CFG_IMMR 0xE0000000
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+
+#define CFG_83XX_DDR_USES_CS0
+
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
+
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#if defined(CONFIG_SPD_EEPROM)
+/*
+ * Determine DDR configuration from I2C interface.
+ */
+#define SPD_EEPROM_ADDRESS 0x52 /* DDR SODIMM */
+#else
+/*
+ * Manually set up DDR parameters
+ */
+#define CFG_DDR_SIZE 256 /* MB */
+#define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9)
+#define CFG_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */
+#define CFG_DDR_TIMING_2 0x00000800 /* may need tuning */
+#define CFG_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */
+#define CFG_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL 0x045b0100 /* page mode */
+#endif
+
+/*
+ * Memory test
+ */
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00000000 /* memtest region */
+#define CFG_MEMTEST_END 0x00100000
+
+/*
+ * The reserved memory
+ */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CFG_LBC_LBCR 0x00000000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */
+
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
+
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
+ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
+ BR_V) /* valid */
+#define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+
+/*
+ * BCSR on the Local Bus
+ */
+#define CFG_BCSR 0xF8000000
+#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */
+#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */
+
+#define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */
+#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+#define CFG_LB_SDRAM /* if board has SRDAM on local bus */
+
+#ifdef CFG_LB_SDRAM
+#define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE
+#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */
+
+/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ * 64MB mask for AM, OR2[0:7] = 1111 1100
+ * XAM, OR2[17:18] = 11
+ * 9 columns OR2[19-21] = 010
+ * 13 rows OR2[23-25] = 100
+ * EAD set for extra time OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM 0xfc006901
+
+#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON 0x0063b723
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_NORMAL)
+
+#endif
+
+/*
+ * Windows to access PIB via local bus
+ */
+#define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */
+#define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */
+
+/*
+ * CS4 on Local Bus, to PIB
+ */
+#define CFG_BR4_PRELIM 0xf8008801 /* CS4 base address at 0xf8008000 */
+#define CFG_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
+
+/*
+ * CS5 on Local Bus, to PIB
+ */
+#define CFG_BR5_PRELIM 0xf8010801 /* CS5 base address at 0xf8010000 */
+#define CFG_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8360@0"
+#define OF_SOC "soc8360@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8360@e0000000/serial@4500"
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x52} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
+#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI_MEM_BASE 0x80000000
+#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE
+#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI_MMIO_BASE 0x90000000
+#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
+#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI_IO_BASE 0xE0300000
+#define CFG_PCI_IO_PHYS 0xE0300000
+#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
+
+#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE
+#define CFG_PCI_SLV_MEM_BUS 0x00000000
+#define CFG_PCI_SLV_MEM_SIZE 0x80000000
+
+
+#ifdef CONFIG_PCI
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+
+#endif /* CONFIG_PCI */
+
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_PHY_MODE_NEED_CHANGE
+
+#define CONFIG_UEC_ETH1 /* GETH1 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM 0 /* UCC1 */
+#define CFG_UEC1_RX_CLK QE_CLK_NONE
+#define CFG_UEC1_TX_CLK QE_CLK9
+#define CFG_UEC1_ETH_TYPE GIGA_ETH
+#define CFG_UEC1_PHY_ADDR 0
+#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+#define CONFIG_UEC_ETH2 /* GETH2 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM 1 /* UCC2 */
+#define CFG_UEC2_RX_CLK QE_CLK_NONE
+#define CFG_UEC2_TX_CLK QE_CLK4
+#define CFG_UEC2_ETH_TYPE GIGA_ETH
+#define CFG_UEC2_PHY_ADDR 1
+#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+/*
+ * Environment
+ */
+
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_PCI)
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_PCI \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
+#else
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
+#endif
+#else
+#if defined(CONFIG_PCI)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_I2C)
+#else
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_I2C )
+#endif
+#endif
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
+#define CFG_HID2 HID2_HBE
+
+/*
+ * Cache Config
+ */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
+#endif
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* BCSR: cache-inhibit and guarded */
+#define CFG_IBAT2L (CFG_BCSR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U CFG_IBAT3U
+
+/* Local bus SDRAM: cacheable */
+#define CFG_IBAT4L (CFG_LBC_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT4U (CFG_LBC_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10)
+#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+
+#ifdef CONFIG_PCI
+/* PCI MEM space: cacheable */
+#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+#else
+#define CFG_IBAT6L (0)
+#define CFG_IBAT6U (0)
+#define CFG_IBAT7L (0)
+#define CFG_IBAT7U (0)
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_ETHADDR 00:04:9f:ef:01:01
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=1000000\0" \
+ "ramdiskfile=ramfs.83xx\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8349emds.dtb\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index 4bbee97..728083b 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -37,10 +37,11 @@
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC83XX 1 /* MPC83XX family */
#define CONFIG_MPC834X 1 /* MPC834X specific */
+#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_TQM834X 1 /* TQM834X board specific */
/* IMMR Base Addres Register, use Freescale default: 0xff400000 */
-#define CFG_IMMRBAR 0xff400000
+#define CFG_IMMR 0xff400000
/* System clock. Primary input clock when in PCI host mode */
#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */
@@ -56,6 +57,17 @@
*/
#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CFG_SCCR_INIT (SCCR_DEFAULT & (~SCCR_CLK_MASK))
+#define CFG_SCCR_TSEC1CM SCCR_TSEC1CM_1 /* TSEC1 clock setting */
+#define CFG_SCCR_TSEC2CM SCCR_TSEC2CM_1 /* TSEC2 clock setting */
+#define CFG_SCCR_ENCCM SCCR_ENCCM_3 /* ENC clock setting */
+#define CFG_SCCR_USBCM SCCR_USBCM_3 /* USB clock setting */
+#define CFG_SCCR_VAL ( CFG_SCCR_INIT \
+ | CFG_SCCR_TSEC1CM \
+ | CFG_SCCR_TSEC2CM \
+ | CFG_SCCR_ENCCM \
+ | CFG_SCCR_USBCM )
+
/* board pre init: do not call, nothing to do */
#undef CONFIG_BOARD_EARLY_INIT_F
@@ -83,6 +95,7 @@
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_BASE 0x80000000 /* start of FLASH */
+#define CFG_FLASH_SIZE 8 /* FLASH size in MB */
/* buffered writes in the AMD chip set is not supported yet */
#undef CFG_FLASH_USE_BUFFER_WRITE
@@ -197,14 +210,15 @@ extern int tqm834x_num_flash_banks;
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMRBAR + 0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMRBAR + 0x4600)
+#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600)
/*
* I2C
*/
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_FSL_I2C
#define CFG_I2C_SPEED 400000 /* I2C speed: 400KHz */
#define CFG_I2C_SLAVE 0x7F /* slave address */
#define CFG_I2C_OFFSET 0x3000
@@ -235,9 +249,9 @@ extern int tqm834x_num_flash_banks;
#define CONFIG_MII
#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMRBAR + CFG_TSEC1_OFFSET)
+#define CFG_TSEC1 (CFG_IMMR + CFG_TSEC1_OFFSET)
#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMRBAR + CFG_TSEC2_OFFSET)
+#define CFG_TSEC2 (CFG_IMMR + CFG_TSEC2_OFFSET)
#if defined(CONFIG_TSEC_ENET)
@@ -460,8 +474,8 @@ extern int tqm834x_num_flash_banks;
#endif
/* IMMRBAR */
-#define CFG_IBAT6L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT6U (CFG_IMMRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U (CFG_IMMR | BATU_BL_1M | BATU_VS | BATU_VP)
/* FLASH */
#define CFG_IBAT7L (CFG_FLASH_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h
new file mode 100644
index 0000000..262e9d6
--- /dev/null
+++ b/include/configs/p3mx.h
@@ -0,0 +1,450 @@
+/*
+ * (C) Copyright 2006
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * Based on original work by
+ * Roel Loeffen, (C) Copyright 2006 Prodrive B.V.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * p3mx.h - configuration for Prodrive P3M750 & P3M7448 boards
+ *
+ * The defines:
+ * CONFIG_P3M750 or
+ * CONFIG_P3M7448
+ * are written into include/config.h by the "make xxx_config" command
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_P3Mx /* used for both board versions */
+
+#if defined (CONFIG_P3M750)
+#define CONFIG_750FX /* 750GL/GX/FX */
+#define CFG_BOARD_NAME "P3M750"
+#define CFG_BUS_HZ 100000000
+#define CFG_BUS_CLK CFG_BUS_HZ
+#define CFG_TCLK 100000000
+#elif defined (CONFIG_P3M7448)
+#define CONFIG_74xx
+#define CFG_BOARD_NAME "P3M7448"
+#define CFG_BUS_HZ 133333333
+#define CFG_BUS_CLK CFG_BUS_HZ
+#define CFG_TCLK 133333333
+#endif
+#define CFG_GT_DUAL_CPU /* also for JTAG even with one cpu */
+
+/* which initialization functions to call for this board */
+#define CFG_BOARD_ASM_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */
+#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE 0x00000000
+#ifdef CONFIG_P3M750
+#define CFG_SDRAM1_BASE 0x10000000 /* each 256 MByte */
+#endif
+
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#if defined (CONFIG_P3M750)
+#define CFG_FLASH_BASE 0xff800000 /* start of flash banks */
+#define CFG_BOOT_SIZE _8M /* boot flash */
+#elif defined (CONFIG_P3M7448)
+#define CFG_FLASH_BASE 0xff000000 /* start of flash banks */
+#define CFG_BOOT_SIZE _16M /* boot flash */
+#endif
+#define CFG_BOOT_SPACE CFG_FLASH_BASE /* BOOT_CS0 flash 0 */
+#define CFG_MONITOR_BASE 0xfff00000
+#define CFG_RESET_ADDRESS 0xfff00100
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
+#define CFG_MISC_REGION_BASE 0xf0000000
+
+#define CFG_DFL_GT_REGS 0xf1000000 /* boot time GT_REGS */
+#define CFG_GT_REGS 0xf1000000 /* GT Registers are mapped here */
+#define CFG_INT_SRAM_BASE 0x42000000 /* GT offers 256k internal SRAM */
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+ /*
+ * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS
+ * To an unused memory region. The stack will remain in cache until RAM
+ * is initialized
+*/
+#undef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0x42000000
+#define CFG_INIT_RAM_END 0x1000
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_MPSC /* MV64460 Serial */
+#define CONFIG_MPSC_PORT 0
+#define CONFIG_BAUDRATE 115200 /* console baudrate */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*-----------------------------------------------------------------------
+ * Ethernet
+ *----------------------------------------------------------------------*/
+/* Change the default ethernet port, use this define (options: 0, 1, 2) */
+#define CFG_ETH_PORT ETH_0
+#define CONFIG_NET_MULTI
+#define MV_ETH_DEVS 2
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#if defined (CONFIG_P3M750)
+#define CFG_ENV_SECT_SIZE 0x20000 /* one sector (1 device)*/
+#elif defined (CONFIG_P3M7448)
+#define CFG_ENV_SECT_SIZE 0x40000 /* two sectors (2 devices parallel */
+#endif
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CONFIG_MV64460_ECC
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CFG_I2C_SPEED 100000 /* I2C speed default */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11 1
+#define CFG_I2C_RTC_ADDR 0x68
+#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show devices on bus */
+
+/* PCI MEMORY MAP section */
+#define CFG_PCI0_MEM_BASE 0x80000000
+#define CFG_PCI0_MEM_SIZE _128M
+#define CFG_PCI1_MEM_BASE 0x88000000
+#define CFG_PCI1_MEM_SIZE _128M
+
+#define CFG_PCI0_0_MEM_SPACE (CFG_PCI0_MEM_BASE)
+#define CFG_PCI1_0_MEM_SPACE (CFG_PCI1_MEM_BASE)
+
+/* PCI I/O MAP section */
+#define CFG_PCI0_IO_BASE 0xfa000000
+#define CFG_PCI0_IO_SIZE _16M
+#define CFG_PCI1_IO_BASE 0xfb000000
+#define CFG_PCI1_IO_SIZE _16M
+
+#define CFG_PCI0_IO_SPACE (CFG_PCI0_IO_BASE)
+#define CFG_PCI0_IO_SPACE_PCI 0x00000000
+#define CFG_PCI1_IO_SPACE (CFG_PCI1_IO_BASE)
+#define CFG_PCI1_IO_SPACE_PCI 0x00000000
+
+#define CFG_ISA_IO_BASE_ADDRESS (CFG_PCI0_IO_BASE)
+
+#define CFG_PCI_IDSEL 0x30
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "u-boot=p3mx/u-boot/u-boot.bin\0" \
+ "load=tftp 100000 ${u-boot}\0" \
+ "update=protect off fff00000 fff3ffff;era fff00000 fff3ffff;" \
+ "cp.b 100000 fff00000 40000;" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load;run update\0" \
+ "serverip=11.0.0.152\0"
+
+#if defined (CONFIG_P3M750)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_EXTRA_ENV_SETTINGS_COMMON \
+ "hostname=p3m750\0" \
+ "bootfile=/tftpboot/p3mx/vxWorks.st\0" \
+ "kernel_addr=fc000000\0" \
+ "ramdisk_addr=fc180000\0" \
+ "vxfile=p3m750/vxWorks\0" \
+ "vxuser=ddg\0" \
+ "vxpass=ddg\0" \
+ "vxtarget=target\0" \
+ "vxflags=0x8\0" \
+ "vxargs=setenv bootargs mgi(0,0)host:${vxfile} h=${serverip} " \
+ "e=${ipaddr} u=${vxuser} pw=${vxpass} tn=${vxtarget} " \
+ "f=${vxflags}\0"
+#elif defined (CONFIG_P3M7448)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_EXTRA_ENV_SETTINGS_COMMON \
+ "hostname=p3m7448\0"
+#endif
+
+#if defined (CONFIG_P3M750)
+#define CONFIG_BOOTCOMMAND "tftp;run vxargs;bootvx"
+#elif defined (CONFIG_P3M7448)
+#define CONFIG_BOOTCOMMAND " "
+#endif
+
+#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_BOOTFILESIZE)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_PCI | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_SDRAM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x08000000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * Marvell MV64460 config settings
+ *----------------------------------------------------------------------*/
+/* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected device width */
+#if defined (CONFIG_P3M750)
+#define CFG_BOOT_PAR 0x8FDFF87F /* 16 bit flash, disable burst*/
+#elif defined (CONFIG_P3M7448)
+#define CFG_BOOT_PAR 0x8FEFFFFF /* 32 bit flash, burst enabled */
+#endif
+
+/*
+ * MPP[0] Serial Port 0 TxD TxD OUT Connected to P14 (buffered)
+ * MPP[1] Serial Port 0 RxD RxD IN Connected to P14 (buffered)
+ * MPP[2] NC
+ * MPP[3] Serial Port 1 TxD TxD OUT Connected to P14 (buffered)
+ * MPP[4] PCI Monarch# GPIO IN Connected to P12
+ * MPP[5] Serial Port 1 RxD RxD IN Connected to P14 (buffered)
+ * MPP[6] PMC Carrier Interrupt 0 Int IN Connected to P14
+ * MPP[7] PMC Carrier Interrupt 1 Int IN Connected to P14
+ * MPP[8] Reserved Do not use
+ * MPP[9] Reserved Do not use
+ * MPP[10] Reserved Do not use
+ * MPP[11] Reserved Do not use
+ * MPP[12] Phy 0 Interrupt Int IN
+ * MPP[13] Phy 1 Interrupt Int IN
+ * MPP[14] NC
+ * MPP[15] NC
+ * MPP[16] PCI Interrupt C Int IN Connected to P11
+ * MPP[17] PCI Interrupt D Int IN Connected to P11
+ * MPP[18] Watchdog NMI# GPIO IN Connected to MPP[24]
+ * MPP[19] Watchdog Expired# WDE OUT Connected to rst logic
+ * MPP[20] Watchdog Status WD_STS IN Read back of rst by watchdog
+ * MPP[21] NC
+ * MPP[22] GP LED Green GPIO OUT
+ * MPP[23] GP LED Red GPIO OUT
+ * MPP[24] Watchdog NMI# Int OUT
+ * MPP[25] NC
+ * MPP[26] NC
+ * MPP[27] PCI Interrupt A Int IN Connected to P11
+ * MPP[28] NC
+ * MPP[29] PCI Interrupt B Int IN Connected to P11
+ * MPP[30] Module reset GPIO OUT Board reset
+ * MPP[31] PCI EReady GPIO IN Connected to P12
+ */
+#define CFG_MPP_CONTROL_0 0x00303022
+#define CFG_MPP_CONTROL_1 0x00000000
+#define CFG_MPP_CONTROL_2 0x00004000
+#define CFG_MPP_CONTROL_3 0x00000004
+#define CFG_GPP_LEVEL_CONTROL 0x280730D0
+
+/*----------------------------------------------------------------------
+ * Initial BAT mappings
+ */
+
+/* NOTES:
+ * 1) GUARDED and WRITE_THRU not allowed in IBATS
+ * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
+ */
+/* SDRAM */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L (CFG_SDRAM_BASE | BATL_PP_RW | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT)
+#define CFG_DBAT0U CFG_IBAT0U
+
+/* init ram */
+#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* PCI0, PCI1 in one BAT */
+#define CFG_IBAT2L BATL_NO_ACCESS
+#define CFG_IBAT2U CFG_DBAT2U
+#define CFG_DBAT2L (CFG_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (CFG_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* GT regs, bootrom, all the devices, PCI I/O */
+#define CFG_IBAT3L (CFG_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
+#define CFG_IBAT3U (CFG_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
+#define CFG_DBAT3L (CFG_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U CFG_IBAT3U
+
+#define CFG_IBAT4L (CFG_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U (CFG_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT4L (CFG_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U CFG_IBAT4U
+
+/* set rest out of range for Linux !!!!!!!!!!! */
+
+/* IBAT5 and DBAT5 */
+#define CFG_IBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT5U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT5U CFG_IBAT5U
+
+/* IBAT6 and DBAT6 */
+#define CFG_IBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT6U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U CFG_IBAT6U
+
+/* IBAT7 and DBAT7 */
+#define CFG_IBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT7U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT7U CFG_IBAT7U
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
+#define CFG_VXWORKS_MAC_PTR 0x42010000 /* use some memory in SRAM that's not used!!! */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * L2CR setup -- make sure this is right for your board!
+ * look in include/mpc74xx.h for the defines used here
+ */
+#define CFG_L2
+
+#if defined (CONFIG_750CX) || defined (CONFIG_750FX)
+#define L2_INIT 0
+#else
+#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
+ L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
+#endif
+
+#define L2_ENABLE (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */