diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/pcs440ep.h | 82 |
1 files changed, 79 insertions, 3 deletions
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 751b512..0e83e48 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -106,19 +106,26 @@ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +#define CONFIG_ENV_OVERWRITE 1 /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +#define ENV_NAME_REVLEV "revision_level" +#define ENV_NAME_SOLDER "solder_switch" +#define ENV_NAME_DIP "dip" + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #undef CONFIG_DDR_ECC /* don't use ECC */ #define SPD_EEPROM_ADDRESS {0x50} +#define CONFIG_PROG_SDRAM_TLB 1 /*----------------------------------------------------------------------- * I2C @@ -143,6 +150,8 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "hostname=pcs440ep\0" \ + "use_eeprom_ethaddr=default\0" \ + "cs_test=off\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -173,6 +182,36 @@ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +/* check U-Boot image with SHA1 sum */ +#define CONFIG_SHA1_CHECK_UB_IMG 1 +#define CONFIG_SHA1_START CFG_MONITOR_BASE +#define CONFIG_SHA1_LEN CFG_MONITOR_LEN + +/*----------------------------------------------------------------------- + * Definitions for status LED + */ +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED 1 + +#define STATUS_LED_BIT 0x08 /* LED 1 is on GPIO_PPC_1 */ +#define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE STATUS_LED_OFF +#define STATUS_LED_BIT1 0x04 /* LED 2 is on GPIO_PPC_2 */ +#define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_BIT2 0x02 /* LED 3 is on GPIO_PPC_3 */ +#define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE2 STATUS_LED_OFF +#define STATUS_LED_BIT3 0x01 /* LED 4 is on GPIO_PPC_4 */ +#define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE3 STATUS_LED_OFF + +#define CONFIG_SHOW_BOOT_PROGRESS 1 + #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ @@ -214,7 +253,10 @@ CFG_CMD_DIAG | \ CFG_CMD_EEPROM | \ CFG_CMD_ELF | \ + CFG_CMD_EXT2 | \ + CFG_CMD_FAT | \ CFG_CMD_I2C | \ + CFG_CMD_IDE | \ CFG_CMD_IRQ | \ CFG_CMD_MII | \ CFG_CMD_NET | \ @@ -222,9 +264,8 @@ CFG_CMD_PCI | \ CFG_CMD_PING | \ CFG_CMD_REGINFO | \ + CFG_CMD_REISER | \ CFG_CMD_SDRAM | \ - CFG_CMD_EXT2 | \ - CFG_CMD_FAT | \ CFG_CMD_USB ) @@ -410,4 +451,39 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ + +#define CONFIG_IDE_PREINIT 1 +#define CONFIG_IDE_RESET 1 + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_CF1 + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET (0x0000) + +/* This addresses need to be shifted one place to the left + * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0) + * This values are shifted + */ +#define CFG_ATA_PORT_ADDR(port) ((port) << 1) + #endif /* __CONFIG_H */ |