diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/IceCube.h | 2 | ||||
| -rw-r--r-- | include/configs/NC650.h | 12 | ||||
| -rw-r--r-- | include/configs/atstk1002.h | 69 | ||||
| -rw-r--r-- | include/configs/mpc7448hpc2.h | 411 |
4 files changed, 462 insertions, 32 deletions
diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index 0d38254..5988112 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -182,7 +182,7 @@ #define OF_CPU "PowerPC,5200@0" #define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 8) +#define OF_TBCLK (bd->bi_busfreq / 4) #define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" /* diff --git a/include/configs/NC650.h b/include/configs/NC650.h index 8da29c4..a12c8da 100644 --- a/include/configs/NC650.h +++ b/include/configs/NC650.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2006 Detlev Zundel, dzu@denx.de + * (C) Copyright 2006, 2007 Detlev Zundel, dzu@denx.de * (C) Copyright 2005 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * @@ -237,18 +237,8 @@ /* * NAND flash support */ -#define CFG_NAND_LEGACY - #define CFG_MAX_NAND_DEVICE 1 -#define NAND_ChipID_UNKNOWN 0x00 -#define SECTORSIZE 512 -#define NAND_MAX_FLOORS 1 #define NAND_MAX_CHIPS 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 -#define ADDR_COLUMN 1 -#define NAND_NO_RB - /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h index 458ebab..beaf385 100644 --- a/include/configs/atstk1002.h +++ b/include/configs/atstk1002.h @@ -62,11 +62,14 @@ */ #define CFG_PLL0_OPT 0x04 -#define CFG_USART1 1 - -#define CFG_CONSOLE_UART_DEV DEVICE_USART1 +#undef CONFIG_USART0 +#define CONFIG_USART1 1 +#undef CONFIG_USART2 +#undef CONFIG_USART3 /* User serviceable stuff */ +#define CONFIG_DOS_PARTITION 1 + #define CONFIG_CMDLINE_TAG 1 #define CONFIG_SETUP_MEMORY_TAGS 1 #define CONFIG_INITRD_TAG 1 @@ -75,16 +78,47 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTARGS \ - "console=ttyUS0 root=/dev/mtdblock1 fbmem=600k" + "console=ttyS0 root=/dev/mtdblock1 rootfstype=jffs2 fbmem=600k" + +#define CONFIG_BOOTCOMMAND \ + "fsload; bootm $(fileaddr)" + +/* + * Only interrupt autoboot if <space> is pressed. Otherwise, garbage + * data on the serial line may interrupt the boot sequence. + */ +#define CONFIG_BOOTDELAY 2 +#define CONFIG_AUTOBOOT 1 +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n" +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * These are "locally administered ethernet addresses" generated by + * ./tools/gen_eth_addr + * + * After booting the board for the first time, new addresses should be + * generated and assigned to the environment variables "ethaddr" and + * "eth1addr". + */ +#define CONFIG_ETHADDR "6a:87:71:14:cd:cb" +#define CONFIG_ETH1ADDR "ca:f8:15:e6:3e:e6" +#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 +#define CONFIG_NET_MULTI 1 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_SUBNETMASK \ + | CONFIG_BOOTP_GATEWAY) #define CONFIG_COMMANDS (CFG_CMD_BDI \ | CFG_CMD_LOADS \ | CFG_CMD_LOADB \ - /* | CFG_CMD_IMI */ \ + | CFG_CMD_IMI \ /* | CFG_CMD_CACHE */ \ | CFG_CMD_FLASH \ | CFG_CMD_MEMORY \ - /* | CFG_CMD_NET */ \ + | CFG_CMD_NET \ | CFG_CMD_ENV \ /* | CFG_CMD_IRQ */ \ | CFG_CMD_BOOTD \ @@ -96,7 +130,7 @@ /* | CFG_CMD_I2C */ \ | CFG_CMD_REGINFO \ /* | CFG_CMD_DATE */ \ - /* | CFG_CMD_DHCP */ \ + | CFG_CMD_DHCP \ /* | CFG_CMD_AUTOSCRIPT */ \ /* | CFG_CMD_MII */ \ | CFG_CMD_MISC \ @@ -106,19 +140,22 @@ /* | CFG_CMD_SAVES */ \ /* | CFG_CMD_SPI */ \ /* | CFG_CMD_PING */ \ - /* | CFG_CMD_MMC */ \ - /* | CFG_CMD_FAT */ \ - /* | CFG_CMD_IMLS */ \ + | CFG_CMD_MMC \ + | CFG_CMD_FAT \ + | CFG_CMD_IMLS \ /* | CFG_CMD_ITEST */ \ - /* | CFG_CMD_EXT2 */ \ + | CFG_CMD_EXT2 \ + | CFG_CMD_JFFS2 \ ) #include <cmd_confdefs.h> #define CONFIG_ATMEL_USART 1 +#define CONFIG_MACB 1 #define CONFIG_PIO2 1 #define CFG_NR_PIOS 5 #define CFG_HSDRAMC 1 +#define CONFIG_MMC 1 #define CFG_DCACHE_LINESZ 32 #define CFG_ICACHE_LINESZ 32 @@ -150,16 +187,8 @@ #define CFG_INIT_SP_ADDR (CFG_INTRAM_BASE + CFG_INTRAM_SIZE) #define CFG_MALLOC_LEN (256*1024) -#define CFG_MALLOC_END \ - ({ \ - DECLARE_GLOBAL_DATA_PTR; \ - CFG_SDRAM_BASE + gd->sdram_size; \ - }) -#define CFG_MALLOC_START (CFG_MALLOC_END - CFG_MALLOC_LEN) - #define CFG_DMA_ALLOC_LEN (16384) -#define CFG_DMA_ALLOC_END (CFG_MALLOC_START) -#define CFG_DMA_ALLOC_START (CFG_DMA_ALLOC_END - CFG_DMA_ALLOC_LEN) + /* Allow 2MB for the kernel run-time image */ #define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x00200000) #define CFG_BOOTPARAMS_LEN (16 * 1024) diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h new file mode 100644 index 0000000..243a3f6 --- /dev/null +++ b/include/configs/mpc7448hpc2.h @@ -0,0 +1,411 @@ +/* + * Copyright (c) 2005 Freescale Semiconductor, Inc. + * + * (C) Copyright 2006 + * Alex Bounine , Tundra Semiconductor Corp. + * Roy Zang , <tie-fei.zang@freescale.com> Freescale Corp. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board specific configuration options for Freescale + * MPC7448HPC2 (High-Performance Computing II) (Taiga) board + * + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* Board Configuration Definitions */ +/* MPC7448HPC2 (High-Performance Computing II) (Taiga) board */ + +#define CONFIG_MPC7448HPC2 + +#define CONFIG_74xx +#define CONFIG_750FX /* this option to enable init of extended BATs */ +#define CONFIG_ALTIVEC /* undef to disable */ + +#define CFG_BOARD_NAME "MPC7448 HPC II" +#define CONFIG_IDENT_STRING " Freescale MPC7448 HPC II" + +#define CFG_OCN_CLK 133000000 /* 133 MHz */ +#define CFG_CONFIG_BUS_CLK 133000000 + +#define CFG_CLK_SPREAD /* Enable Spread-Spectrum Clock generation */ + +#undef CONFIG_ECC /* disable ECC support */ + +/* Board-specific Initialization Functions to be called */ +#define CFG_BOARD_ASM_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HAS_ETH1 + +#define CONFIG_ENV_OVERWRITE + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115000 */ + +/*#define CFG_HUSH_PARSER */ +#undef CFG_HUSH_PARSER + +#define CFG_PROMPT_HUSH_PS2 "> " + +/* Pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,7448@0" +#define OF_TSI "tsi108@c0000000" +#define OF_TBCLK (bd->bi_busfreq / 8) +#define OF_STDOUT_PATH "/tsi108@c0000000/serial@7808" + +/* + * The following defines let you select what serial you want to use + * for your console driver. + * + * what to do: + * If you have hacked a serial cable onto the second DUART channel, + * change the CFG_DUART port from 1 to 0 below. + * + */ + +#define CONFIG_CONS_INDEX 1 +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK CFG_OCN_CLK * 8 + +#define CFG_NS16550_COM1 (CFG_TSI108_CSR_RST_BASE+0x7808) +#define CFG_NS16550_COM2 (CFG_TSI108_CSR_RST_BASE+0x7C08) +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#undef CONFIG_BOOTARGS +/* #define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" + * to mount root filesystem over NFS;echo" */ + +#if (CONFIG_BOOTDELAY >= 0) +#define CONFIG_BOOTCOMMAND "tftpboot 0x400000 zImage.initrd.elf;\ + setenv bootargs $(bootargs) $(bootargs_root) nfsroot=$(serverip):$(rootpath) \ + ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000; " + +#define CONFIG_BOOTARGS "console=ttyS0,115200" +#endif + +#undef CONFIG_EXTRA_ENV_SETTINGS + +#define CONFIG_SERIAL "No. 1" + +/* Networking Configuration */ + +#define KSEG1ADDR(a) (a) /* Needed by the rtl8139 driver */ + +#define CONFIG_TSI108_ETH +#define CONFIG_TSI108_ETH_NUM_PORTS 2 + +#define CONFIG_NET_MULTI + +#define CONFIG_BOOTFILE zImage.initrd.elf +#define CONFIG_LOADADDR 0x400000 + +/*-------------------------------------------------------------------------- */ + +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_ASKENV \ + | CFG_CMD_CACHE \ + | CFG_CMD_PCI \ + | CFG_CMD_I2C \ + | CFG_CMD_SDRAM \ + | CFG_CMD_EEPROM \ + | CFG_CMD_FLASH \ + | CFG_CMD_ENV \ + | CFG_CMD_BSP \ + | CFG_CMD_DHCP \ + | CFG_CMD_PING \ + | CFG_CMD_DATE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/*set date in u-boot*/ +#define CONFIG_RTC_M48T35A +#define CFG_NVRAM_BASE_ADDR 0xfc000000 +#define CFG_NVRAM_SIZE 0x8000 +/* + * Miscellaneous configurable options + */ +#define CONFIG_VERSION_VARIABLE 1 +#define CONFIG_TSI108_I2C + +#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C EEPROM page 1 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)/* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00400000 /* default load address */ + +#define CFG_HZ 1000 /* decr freq: 1ms ticks */ + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area + */ + +/* + * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS + * To an unused memory region. The stack will remain in cache until RAM + * is initialized + */ +#undef CFG_INIT_RAM_LOCK +#define CFG_INIT_RAM_ADDR 0x07d00000 /* unused memory region */ +#define CFG_INIT_RAM_END 0x4000/* larger space - we have SDRAM initialized */ + +#define CFG_GBL_DATA_SIZE 128/* size in bytes reserved for init data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ + +#define CFG_SDRAM_BASE 0x00000000 /* first 256 MB of SDRAM */ +#define CFG_SDRAM1_BASE 0x10000000 /* next 256MB of SDRAM */ + +#define CFG_SDRAM2_BASE 0x40000000 /* beginning of non-cacheable alias for SDRAM - first 256MB */ +#define CFG_SDRAM3_BASE 0x50000000 /* next Non-Cacheable 256MB of SDRAM */ + +#define CFG_PCI_PFM_BASE 0x80000000 /* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */ + +#define CFG_PCI_MEM32_BASE 0xE0000000 /* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */ + +#define CFG_MISC_REGION_BASE 0xf0000000 /* Base Address for (PCI/X + Flash) region */ + +#define CFG_FLASH_BASE 0xff000000 /* Base Address of Flash device */ +#define CFG_FLASH_BASE2 0xfe000000 /* Alternate Flash Base Address */ + +#define CONFIG_VERY_BIG_RAM /* we will use up to 256M memory for cause we are short of BATS */ + +#define PCI0_IO_BASE_BOOTM 0xfd000000 + +#define CFG_RESET_ADDRESS 0x3fffff00 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* u-boot code base */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ + +/* Peripheral Device section */ + +/* + * Resources on the Tsi108 + */ + +#define CFG_TSI108_CSR_RST_BASE 0xC0000000 /* Tsi108 CSR base after reset */ +#define CFG_TSI108_CSR_BASE CFG_TSI108_CSR_RST_BASE /* Runtime Tsi108 CSR base */ + +#define ENABLE_PCI_CSR_BAR /* enables access to Tsi108 CSRs from the PCI/X bus */ + +#undef DISABLE_PBM + +/* + * PCI stuff + * + */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_TSI108_PCI /* include tsi108 pci support */ + +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +/* PCI MEMORY MAP section */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +/* PCI Memory Space */ +#define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS) +#define CFG_PCI_MEM_PHYS (CFG_PCI_MEM32_BASE) /* 0xE0000000 */ +#define CFG_PCI_MEM_SIZE 0x10000000 /* 256 MB space for PCI/X Mem + SDRAM OCN */ + +/* PCI I/O Space */ +#define CFG_PCI_IO_BUS 0x00000000 +#define CFG_PCI_IO_PHYS 0xfa000000 /* Changed from fd000000 */ + +#define CFG_PCI_IO_SIZE 0x01000000 /* 16MB */ + +#define _IO_BASE 0x00000000 /* points to PCI I/O space */ + +/* PCI Config Space mapping */ +#define CFG_PCI_CFG_BASE 0xfb000000 /* Changed from FE000000 */ +#define CFG_PCI_CFG_SIZE 0x01000000 /* 16MB */ + +#define CFG_IBAT0U 0xFE0003FF +#define CFG_IBAT0L 0xFE000002 + +#define CFG_IBAT1U 0x00007FFF +#define CFG_IBAT1L 0x00000012 + +#define CFG_IBAT2U 0x80007FFF +#define CFG_IBAT2L 0x80000022 + +#define CFG_IBAT3U 0x00000000 +#define CFG_IBAT3L 0x00000000 + +#define CFG_IBAT4U 0x00000000 +#define CFG_IBAT4L 0x00000000 + +#define CFG_IBAT5U 0x00000000 +#define CFG_IBAT5L 0x00000000 + +#define CFG_IBAT6U 0x00000000 +#define CFG_IBAT6L 0x00000000 + +#define CFG_IBAT7U 0x00000000 +#define CFG_IBAT7L 0x00000000 + +#define CFG_DBAT0U 0xE0003FFF +#define CFG_DBAT0L 0xE000002A + +#define CFG_DBAT1U 0x00007FFF +#define CFG_DBAT1L 0x00000012 + +#define CFG_DBAT2U 0x00000000 +#define CFG_DBAT2L 0x00000000 + +#define CFG_DBAT3U 0xC0000003 +#define CFG_DBAT3L 0xC000002A + +#define CFG_DBAT4U 0x00000000 +#define CFG_DBAT4L 0x00000000 + +#define CFG_DBAT5U 0x00000000 +#define CFG_DBAT5L 0x00000000 + +#define CFG_DBAT6U 0x00000000 +#define CFG_DBAT6L 0x00000000 + +#define CFG_DBAT7U 0x00000000 +#define CFG_DBAT7L 0x00000000 + +/* I2C addresses for the two DIMM SPD chips */ +#define DIMM0_I2C_ADDR 0x51 +#define DIMM1_I2C_ADDR 0x52 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1/* Flash can be at one of two addresses */ +#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */ +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_WRITE_SWAPPED_DATA + +#define PHYS_FLASH_SIZE 0x01000000 +#define CFG_MAX_FLASH_SECT (128) + +#define CFG_ENV_IS_IN_NVRAM +#define CFG_ENV_ADDR 0xFC000000 + +#define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x00000400 /* Total Size of Environment Space */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * L2CR setup -- make sure this is right for your board! + * look in include/mpc74xx.h for the defines used here + */ +#undef CFG_L2 + +#define L2_INIT 0 +#define L2_ENABLE (L2_INIT | L2CR_L2E) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CFG_SERIAL_HANG_IN_EXCEPTION +#endif /* __CONFIG_H */ |