diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/PPChameleonEVB.h | 90 | ||||
| -rw-r--r-- | include/configs/netstar.h | 265 |
2 files changed, 351 insertions, 4 deletions
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index 7ca827f..c406c8f 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -188,10 +188,14 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ + +/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */ +#define CONFIG_NEW_NAND_CODE #define CFG_NAND0_BASE 0xFF400000 #define CFG_NAND1_BASE 0xFF000000 - -#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, CFG_NAND1_BASE } +#define NAND_BIG_DELAY_US 25 +#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ #define SECTORSIZE 512 #define NAND_NO_RB @@ -213,6 +217,83 @@ #define CFG_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ #define CFG_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ +#ifdef CONFIG_NEW_NAND_CODE +#define MACRO_NAND_DISABLE_CE(nandptr) do \ +{ \ + switch((unsigned long)nandptr) \ + { \ + case CFG_NAND0_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CE); \ + break; \ + case CFG_NAND1_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_CE); \ + break; \ + } \ +} while(0) + +#define MACRO_NAND_ENABLE_CE(nandptr) do \ +{ \ + switch((unsigned long)nandptr) \ + { \ + case CFG_NAND0_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CE); \ + break; \ + case CFG_NAND1_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_CE); \ + break; \ + } \ +} while(0) + +#define MACRO_NAND_CTL_CLRALE(nandptr) do \ +{ \ + switch((unsigned long)nandptr) \ + { \ + case CFG_NAND0_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_ALE); \ + break; \ + case CFG_NAND1_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_ALE); \ + break; \ + } \ +} while(0) + +#define MACRO_NAND_CTL_SETALE(nandptr) do \ +{ \ + switch((unsigned long)nandptr) \ + { \ + case CFG_NAND0_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_ALE); \ + break; \ + case CFG_NAND1_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_ALE); \ + break; \ + } \ +} while(0) + +#define MACRO_NAND_CTL_CLRCLE(nandptr) do \ +{ \ + switch((unsigned long)nandptr) \ + { \ + case CFG_NAND0_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CLE); \ + break; \ + case CFG_NAND1_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_CLE); \ + break; \ + } \ +} while(0) + +#define MACRO_NAND_CTL_SETCLE(nandptr) do { \ + switch((unsigned long)nandptr) { \ + case CFG_NAND0_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CLE); \ + break; \ + case CFG_NAND1_BASE: \ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_CLE); \ + break; \ + } \ +} while(0) +#else #define NAND_DISABLE_CE(nand) do \ { \ switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \ @@ -288,6 +369,7 @@ break; \ } \ } while(0) +#endif /* !CONFIG_NEW_NAND_CODE */ #ifdef NAND_NO_RB /* constant delay (see also tR in the datasheet) */ @@ -338,16 +420,16 @@ #define CFG_SDRAM_BASE 0x00000000 /* Reserve 256 kB for Monitor */ +/* #define CFG_FLASH_BASE 0xFFFC0000 #define CFG_MONITOR_BASE CFG_FLASH_BASE #define CFG_MONITOR_LEN (256 * 1024) +*/ /* Reserve 320 kB for Monitor */ -/* #define CFG_FLASH_BASE 0xFFFB0000 #define CFG_MONITOR_BASE CFG_FLASH_BASE #define CFG_MONITOR_LEN (320 * 1024) -*/ #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ diff --git a/include/configs/netstar.h b/include/configs/netstar.h new file mode 100644 index 0000000..30d2654 --- /dev/null +++ b/include/configs/netstar.h @@ -0,0 +1,265 @@ +/* + * (C) Copyright 2005 2N TELEKOMUNIKACE, Ladislav Michl + * + * Configuation settings for the TI OMAP NetStar board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <configs/omap1510.h> + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_ARM925T 1 /* This is an arm925t CPU */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP1510 1 /* which is in a 5910 */ + +/* Input clock of PLL */ +#define CONFIG_SYS_CLK_FREQ 150000000 /* 150MHz input clock */ +#define CONFIG_XTAL_FREQ 12000000 + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_MISC_INIT_R /* There is nothing to really init */ +#define BOARD_LATE_INIT /* but we flash the LEDs here */ + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CFG_DEVICE_NULLDEV 1 /* enable null device */ +#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */ + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ + +/* + * FLASH organization + */ +#define CFG_FLASH_BASE PHYS_FLASH_1 +#define CFG_MAX_FLASH_BANKS 1 +#if (PHYS_SDRAM_1_SIZE == SZ_32M) +/*#if 1*/ +#define CFG_FLASH_CFI /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER /* Use the common driver */ +#define CFG_FLASH_EMPTY_INFO +#define CFG_MAX_FLASH_SECT 128 +#else +#define PHYS_FLASH_1_SIZE SZ_1M +#define CFG_MAX_FLASH_SECT 19 +#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ) /* in ticks */ +#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) +#endif + +#define CFG_MONITOR_BASE PHYS_FLASH_1 +#define CFG_MONITOR_LEN SZ_256K + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH +#define ENV_IS_SOLITARY +#define CFG_ENV_ADDR 0x4000 +#define CFG_ENV_SIZE SZ_8K +#define CFG_ENV_SECT_SIZE SZ_8K +#define CFG_ENV_ADDR_REDUND 0x6000 +#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE +#define CONFIG_ENV_OVERWRITE + +/* + * Size of malloc() pool + */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +/* XXX #define CFG_MALLOC_LEN (SZ_64K - CFG_GBL_DATA_SIZE)*/ +#define CFG_MALLOC_LEN SZ_4M + +/* + * The stack size is set up in start.S using the settings below + */ +/* XXX #define CONFIG_STACKSIZE SZ_8K /XXX* regular stack */ +#define CONFIG_STACKSIZE SZ_1M /* regular stack */ + +/* + * Hardware drivers + */ +#define CONFIG_DRIVER_SMC91111 +#define CONFIG_SMC91111_BASE 0x04000300 + +/* + * NS16550 Configuration + */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE (-4) +#define CFG_NS16550_CLK (CONFIG_XTAL_FREQ) /* can be 12M/32Khz or 48Mhz */ +#define CFG_NS16550_COM1 OMAP1510_UART1_BASE /* uart1 */ + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/*#define CONFIG_SKIP_RELOCATE_UBOOT*/ +/*#define CONFIG_SKIP_LOWLEVEL_INIT */ + +/* + * NAND flash + */ +#define CFG_MAX_NAND_DEVICE 1 +#define CFG_NAND_BASE 0x04000000 + (2 << 23) +#define CONFIG_NEW_NAND_CODE + +/* + * JFFS2 partitions (mtdparts command line support) + */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=omapflash.0,nand0=omapnand.0" +#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:8k@16k(env),8k(r_env),448k@576k(u-boot);omapnand.0:48M(rootfs0),48M(rootfs1),-(data)" + +#if 0 +#define CONFIG_COMMANDS (CFG_CMD_BDI | \ + CFG_CMD_BOOTD | \ + CFG_CMD_DHCP | \ + CFG_CMD_ENV | \ + CFG_CMD_FLASH | \ + CFG_CMD_IMI | \ + CFG_CMD_LOADB | \ + CFG_CMD_NET | \ + CFG_CMD_MEMORY | \ + CFG_CMD_PING | \ + CFG_CMD_RUN) + +#else +#define CONFIG_COMMANDS (CFG_CMD_BDI | \ + CFG_CMD_BOOTD | \ + CFG_CMD_DHCP | \ + CFG_CMD_ENV | \ + CFG_CMD_FLASH | \ + CFG_CMD_NAND | \ + CFG_CMD_IMI | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_LOADB | \ + CFG_CMD_NET | \ + CFG_CMD_MEMORY | \ + CFG_CMD_PING | \ + CFG_CMD_RUN) + +#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ +#endif + +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT +#define CONFIG_LOOPW + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ +#define CFG_AUTOLOAD "n" /* No autoload */ +#define CONFIG_BOOTCOMMAND "run nboot" +#define CONFIG_PREBOOT "run setup" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "setup=setenv bootargs console=ttyS0,$baudrate " \ + "$mtdparts\0" \ + "ospart=0\0" \ + "setpart=" \ + "if test -n $swapos; then " \ + "if test $ospart -eq 0; then chpart nand0,1; else chpart nand0,0; fi; "\ + "setenv swapos; saveenv; " \ + "else " \ + "chpart nand0,$ospart; " \ + "fi\0" \ + "nfsargs=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \ + "nfsroot=$rootpath root=/dev/nfs\0" \ + "flashargs=run setpart;setenv bootargs $bootargs " \ + "root=/dev/mtdblock$partition ro " \ + "rootfstype=jffs2\0" \ + "initrdargs=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \ + "iboot=bootp;run initrdargs;tftp;bootm\0" \ + "fboot=run flashargs;fsload /boot/uImage;bootm\0" \ + "nboot=bootp;run nfsargs;tftp;bootm\0" + +#if 0 /* feel free to disable for development */ +#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */ +#define CONFIG_AUTOBOOT_PROMPT "\nNetStar PBX - boot in %d sec...\n" +#define CONFIG_AUTOBOOT_DELAY_STR "R" /* 1st "password" */ +#define CONFIG_BOOT_RETRY_TIME 30 +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "# " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_AUTO_COMPLETE + +#define CFG_MEMTEST_START PHYS_SDRAM_1 +#define CFG_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */ + +/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1. + * This time is further subdivided by a local divisor. + */ +#define CFG_TIMERBASE OMAP1510_TIMER1_BASE +#define CFG_PVT 7 /* 2^(pvt+1), divide by 256 */ +#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT)) + +#define OMAP5910_DPLL_DIV 1 +#define OMAP5910_DPLL_MUL ((CONFIG_SYS_CLK_FREQ * \ + (1 << OMAP5910_DPLL_DIV)) / CONFIG_XTAL_FREQ) + +#define OMAP5910_ARM_PER_DIV 2 /* CKL/4 */ +#define OMAP5910_LCD_DIV 2 /* CKL/4 */ +#define OMAP5910_ARM_DIV 0 /* CKL/1 */ +#define OMAP5910_DSP_DIV 0 /* CKL/1 */ +#define OMAP5910_TC_DIV 1 /* CKL/2 */ +#define OMAP5910_DSP_MMU_DIV 1 /* CKL/2 */ +#define OMAP5910_ARM_TIM_SEL 1 /* CKL used for MPU timers */ + +#define OMAP5910_ARM_EN_CLK 0x03d6 /* 0000 0011 1101 0110b Clock Enable */ +#define OMAP5910_ARM_CKCTL ((OMAP5910_ARM_PER_DIV) | \ + (OMAP5910_LCD_DIV << 2) | \ + (OMAP5910_ARM_DIV << 4) | \ + (OMAP5910_DSP_DIV << 6) | \ + (OMAP5910_TC_DIV << 8) | \ + (OMAP5910_DSP_MMU_DIV << 10) | \ + (OMAP5910_ARM_TIM_SEL << 12)) + +#endif /* __CONFIG_H */ |