diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/MPC8572DS.h | 6 | ||||
| -rw-r--r-- | include/configs/MPC8641HPCN.h | 2 | ||||
| -rw-r--r-- | include/configs/P2020DS.h | 7 | ||||
| -rw-r--r-- | include/configs/PM854.h | 1 | ||||
| -rw-r--r-- | include/configs/PM856.h | 1 | ||||
| -rw-r--r-- | include/configs/XPEDITE5170.h | 756 |
6 files changed, 766 insertions, 7 deletions
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 2aba689..6f1b1a4 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -404,7 +404,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* controller 3, direct to uli, tgtid 3, Base address 8000 */ #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull #else #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 @@ -423,7 +423,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* controller 2, Slot 2, tgtid 2, Base address 9000 */ #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull #else #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 @@ -442,7 +442,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* controller 1, Slot 1, tgtid 1, Base address a000 */ #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull #else #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index d8042fb..035874b 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -335,7 +335,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCI1_MEM_PHYS 0x0000000c00000000ULL #else #define CONFIG_SYS_PCI1_MEM_BUS CONFIG_SYS_PCI1_MEM_VIRT diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index a39ff26..fddcce5 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -46,6 +46,7 @@ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE @@ -437,7 +438,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy); /* controller 3, Slot 1, tgtid 3, Base address b000 */ #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull #else #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 @@ -456,7 +457,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy); /* controller 2, direct to uli, tgtid 2, Base address 9000 */ #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull #else #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 @@ -475,7 +476,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy); /* controller 1, Slot 2, tgtid 1, Base address a000 */ #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull #else #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 diff --git a/include/configs/PM854.h b/include/configs/PM854.h index 3f943aa..4b9bcca 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -96,6 +96,7 @@ #undef CONFIG_DDR_SPD #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_FSL_DMA /* use DMA to init DDR ECC */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef diff --git a/include/configs/PM856.h b/include/configs/PM856.h index 43c2873..1db20bc 100644 --- a/include/configs/PM856.h +++ b/include/configs/PM856.h @@ -98,6 +98,7 @@ #undef CONFIG_DDR_SPD #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_FSL_DMA /* use DMA to init DDR ECC */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef diff --git a/include/configs/XPEDITE5170.h b/include/configs/XPEDITE5170.h new file mode 100644 index 0000000..2553293 --- /dev/null +++ b/include/configs/XPEDITE5170.h @@ -0,0 +1,756 @@ +/* + * Copyright 2009 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * xpedite5170 board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_MPC86xx 1 /* MPC86xx */ +#define CONFIG_MPC8641 1 /* MPC8641 specific */ +#define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */ +#define CONFIG_SYS_BOARD_NAME "XPedite5170" +#define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */ +#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ +#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ +#define CONFIG_ALTIVEC 1 + +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* + * DDR config + */ +#define CONFIG_FSL_DDR2 +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ +#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ +#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ +#define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ + +/* + * virtual address to be used for temporary mappings. There + * should be 128k free at this VA. + */ +#define CONFIG_SYS_SCRATCH_VA 0xe0000000 + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */ + +/* + * L2CR setup + */ +#define CONFIG_SYS_L2 +#define L2_INIT 0 +#define L2_ENABLE (L2CR_L2E) + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) + +/* + * Diagnostics + */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 + +/* + * Memory map + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable + * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable + * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable + * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable + * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable + * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable + * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable + * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable + * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable + */ + +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_2 | LCRR_EADC_3) + +/* + * NAND flash configuration + */ +#define CONFIG_SYS_NAND_BASE 0xef800000 +#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2} +#define CONFIG_SYS_MAX_NAND_DEVICE 2 +#define CONFIG_NAND_ACTL +#define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */ +#define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */ +#define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */ +#define CONFIG_SYS_NAND_ACTL_DELAY 25 +#define CONFIG_SYS_NAND_QUIET_TEST +#define CONFIG_JFFS2_NAND + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 +#define CONFIG_SYS_FLASH_BASE2 0xf0000000 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \ + {0xf7f00000, 0xc0000} } +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ + +/* + * Chip select configuration + */ +/* NOR Flash 0 on CS0 */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ + BR_PS_16 |\ + BR_V) +#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\ + OR_GPCM_CSNT |\ + OR_GPCM_XACS |\ + OR_GPCM_ACS_DIV2 |\ + OR_GPCM_SCY_8 |\ + OR_GPCM_TRLX |\ + OR_GPCM_EHTR |\ + OR_GPCM_EAD) + +/* NOR Flash 1 on CS1 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\ + BR_PS_16 |\ + BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM + +/* NAND flash on CS2 */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\ + BR_PS_8 |\ + BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\ + OR_GPCM_BCTLD |\ + OR_GPCM_CSNT |\ + OR_GPCM_ACS_DIV4 |\ + OR_GPCM_SCY_4 |\ + OR_GPCM_TRLX |\ + OR_GPCM_EHTR) + +/* Optional NAND flash on CS3 */ +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\ + BR_PS_8 |\ + BR_V) +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM + +/* + * Use L1 as initial stack + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 +#define CONFIG_SYS_INIT_RAM_END 0x00004000 + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_BAUDRATE 115200 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Use the HUSH parser + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 100000 /* M41T00 only supports 100 KHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE + +/* PEX8518 slave I2C interface */ +#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 + +/* I2C DS1631 temperature sensor */ +#define CONFIG_SYS_I2C_DS1621_ADDR 0x48 +#define CONFIG_DTT_DS1621 +#define CONFIG_DTT_SENSORS { 0 } + +/* I2C EEPROM - AT24C128B */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* GPIO/EEPROM/SRAM */ +#define CONFIG_DS4510 +#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 + +/* GPIO */ +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 +#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c +#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e +#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f +#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 + +/* + * PU = pulled high, PD = pulled low + * I = input, O = output, IO = input/output + */ +/* PCA9557 @ 0x18*/ +#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ +#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ +#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ +#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ + +/* PCA9557 @ 0x1c*/ +#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ +#define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */ +#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ +#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ +#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ +#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ +#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ +#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ + +/* PCA9557 @ 0x1e*/ +#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */ +#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */ + +/* PCA9557 @ 0x1f */ +#define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */ +#define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */ +#define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */ +#define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */ + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +/* PCIE1 - PEX8518 */ +#define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ + +/* PCIE2 - VPX P1 */ +#define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ + +/* + * Networking options + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define CONFIG_HAS_ETH0 + +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_PHY_ADDR 2 +#define TSEC2_PHYIDX 0 +#define CONFIG_HAS_ETH1 + +/* + * BAT mappings + */ +#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) +#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\ + BATU_BL_1M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT) +#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU +#endif + +/* + * BAT0 2G Cacheable, non-guarded + * 0x0000_0000 2G DDR + */ +#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U + +/* + * BAT1 1G Cache-inhibited, guarded + * 0x8000_0000 1G PCI-Express 1 Memory + */ +#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\ + BATU_BL_1G |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U + +/* + * BAT2 512M Cache-inhibited, guarded + * 0xc000_0000 512M PCI-Express 2 Memory + */ +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\ + BATU_BL_512M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U + +/* + * BAT3 1M Cache-inhibited, guarded + * 0xe000_0000 1M CCSR + */ +#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\ + BATU_BL_1M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U + +/* + * BAT4 32M Cache-inhibited, guarded + * 0xe200_0000 16M PCI-Express 1 I/O + * 0xe300_0000 16M PCI-Express 2 I/0 + */ +#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\ + BATU_BL_32M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U + +/* + * BAT5 128K Cacheable, non-guarded + * 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory) + */ +#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\ + BATL_PP_RW |\ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\ + BATU_BL_128K |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L +#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U + +/* + * BAT6 256M Cache-inhibited, guarded + * 0xf000_0000 256M FLASH + */ +#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\ + BATU_BL_256M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\ + BATL_PP_RW |\ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U + +/* Map the last 1M of flash where we're running from reset */ +#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT6U_EARLY (TEXT_BASE |\ + BATU_BL_1M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ + BATL_PP_RW |\ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY + +/* + * BAT7 64M Cache-inhibited, guarded + * 0xe800_0000 64K NAND FLASH + * 0xe804_0000 128K DUART Registers + */ +#define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\ + BATU_BL_512K |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\ + BATL_PP_RW |\ + BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U + +/* + * Command configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DS4510 +#define CONFIG_CMD_DS4510_INFO +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_SAVEENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SNTP + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */ +#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ +#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) + +/* + * Flash memory map: + * fffc0000 - ffffffff Pri FDT (256KB) + * fff80000 - fffbffff Pri U-Boot Environment (256 KB) + * fff00000 - fff7ffff Pri U-Boot (512 KB) + * fef00000 - ffefffff Pri OS image (16MB) + * f8000000 - feefffff Pri OS Use/Filesystem (111MB) + * + * f7fc0000 - f7ffffff Sec FDT (256KB) + * f7f80000 - f7fbffff Sec U-Boot Environment (256 KB) + * f7f00000 - f7f7ffff Sec U-Boot (512 KB) + * f6f00000 - f7efffff Sec OS image (16MB) + * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) + */ +#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff00000) +#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f00000) +#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfffc0000) +#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7fc0000) +#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) +#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) + +#define CONFIG_PROG_UBOOT1 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_UBOOT2 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_BOOT_OS_NET \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "if test -n $fdtaddr; then " \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "bootm $osaddr - $fdtaddr; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi; " \ + "else; " \ + "bootm $osaddr; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS1 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS2 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT1 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT2 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=yes\0" \ + "download_cmd=tftp\0" \ + "console_args=console=ttyS0,115200\0" \ + "root_args=root=/dev/nfs rw\0" \ + "misc_args=ip=on\0" \ + "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ + "bootfile=/home/user/file\0" \ + "osfile=/home/user/uImage-XPedite5170\0" \ + "fdtfile=/home/user/xpedite5170.dtb\0" \ + "ubootfile=/home/user/u-boot.bin\0" \ + "fdtaddr=c00000\0" \ + "osaddr=0x1000000\0" \ + "loadaddr=0x1000000\0" \ + "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ + "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ + "prog_os1="CONFIG_PROG_OS1"\0" \ + "prog_os2="CONFIG_PROG_OS2"\0" \ + "prog_fdt1="CONFIG_PROG_FDT1"\0" \ + "prog_fdt2="CONFIG_PROG_FDT2"\0" \ + "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ + "bootcmd_flash1=run set_bootargs; " \ + "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ + "bootcmd_flash2=run set_bootargs; " \ + "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ + "bootcmd=run bootcmd_flash1\0" +#endif /* __CONFIG_H */ |