diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/PM856.h | 439 |
1 files changed, 439 insertions, 0 deletions
diff --git a/include/configs/PM856.h b/include/configs/PM856.h new file mode 100644 index 0000000..5dae1b6 --- /dev/null +++ b/include/configs/PM856.h @@ -0,0 +1,439 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao <X.Xiao@motorola.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * MicroSys PM856 board configuration file + * + * Please refer to doc/README.mpc85xx for more info. + * + * Make sure you change the MAC address and other network params first, + * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ +#define CONFIG_MPC8560 1 /* MPC8560 specific */ +#define CONFIG_PM856 1 /* PM856 board specific */ + +#define CONFIG_PCI +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE +#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + + +/* + * sysclk for MPC85xx + * + * Two valid values are: + * 33000000 + * 66000000 + * + * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz + * is likely the desired value here, so that is now the default. + * The board, however, can run at 66MHz. In any event, this value + * must match the settings of some switches. Details can be found + * in the README.mpc85xxads. + */ + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 66000000 +#endif + + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest region */ +#define CFG_MEMTEST_END 0x00400000 + + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#if defined(CONFIG_SPD_EEPROM) + /* + * Determine DDR configuration from I2C interface. + */ + #define SPD_EEPROM_ADDRESS 0x58 /* DDR DIMM */ + +#else + /* + * Manually set up DDR parameters + */ + #define CFG_SDRAM_SIZE 256 /* DDR is 256 MB */ + #define CFG_DDR_CS0_BNDS 0x0000000f /* 0-256MB */ + #define CFG_DDR_CS0_CONFIG 0x80000102 + #define CFG_DDR_TIMING_1 0x47444321 + #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ + #define CFG_DDR_CONTROL 0xc2008000 /* unbuffered,no DYN_PWR */ + #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ + #define CFG_DDR_INTERVAL 0x045b0100 /* autocharge,no open page */ +#endif + + +/* + * SDRAM on the Local Bus + */ +#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 0 /* LBC SDRAM is 0 MB */ + +#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ +#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */ + +#define CFG_OR0_PRELIM 0xfe006f67 /* 32MB Flash */ +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_FLASH_EMPTY_INFO + +#undef CONFIG_CLOCKS_IN_MHZ + + +/* + * Local Bus Definitions + */ + +#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ + + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ + +/* + * EEPROM configuration + */ +#define CFG_I2C_EEPROM_ADDR 0x58 +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* + * RTC configuration + */ +#define CONFIG_RTC_PCF8563 +#define CFG_I2C_RTC_ADDR 0x51 + +/* RapidIO MMU */ +#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE +#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC2 1 +#undef CONFIG_MPC85XX_FEC +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 + +#endif /* CONFIG_TSEC_ENET */ + +#define CONFIG_ETHPRIME "ENET0" + +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ + + +/* + * - Rx-CLK is CLK15 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers + * - Full duplex + */ +#define CONFIG_ETHER_ON_FCC3 +#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) +#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) +#define CFG_CPMFCR_RAMTYPE 0 +#define CFG_FCC_PSMR (FCC_PSMR_FDE) + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x80000) + #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CFG_RAMBOOT) + #if defined(CONFIG_PCI) + #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_PCI \ + | CFG_CMD_I2C) \ + & \ + ~(CFG_CMD_ENV \ + | CFG_CMD_LOADS)) + #else + #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_I2C) \ + & \ + ~(CFG_CMD_ENV \ + | CFG_CMD_LOADS)) + #endif +#else + #if defined(CONFIG_PCI) + #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_EEPROM \ + | CFG_CMD_DATE \ + | CFG_CMD_PCI \ + | CFG_CMD_PING \ + | CFG_CMD_I2C) + #else + #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_EEPROM \ + | CFG_CMD_DATE \ + | CFG_CMD_PING \ + | CFG_CMD_I2C) + #endif +#endif + +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x1000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_LOOPW + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_ETHADDR 00:40:42:01:00:00 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:40:42:01:00:01 +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:40:42:01:00:02 +#endif + + +#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx +#define CONFIG_BOOTFILE pm856/uImage + +#define CONFIG_HOSTNAME pm856 +#define CONFIG_IPADDR 192.168.0.103 +#define CONFIG_SERVERIP 192.168.0.64 +#define CONFIG_GATEWAYIP 192.168.0.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 9600 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=400000\0" \ + "ramdiskfile=pm856/uRamdisk\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ |